Search Documents

By J. R. Thoenen

This circular is part 6 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cableway excavators, and hydraulic monitors; part 3, hydraulic, clamshall, ladder, and diaper dredges; part 4, haulage equipment, particularly industrial cars with locomotive or hoist as the motive power; part 5, conveyor belt, motor truck, pump and pipe line, towboat and barges, and aerial-trams haulage. This circular discusses the application of these various types of equipment to the different types of sand and gravel deposits and contains a reference bibliography. It completes the discussion of excavating problems.

Jan 1, 1936

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Edmond Chin

The area encompassed by the political entities included in this study com-prises 11 million square miles or about 15 percent of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest is-land or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The region is noted for its great rivers. The Chang, Huang, Amur, and Mekong are respectively the fifth, sixth, eighth, and eleventh longest rivers in the world. The Ganges-Brahmaputra has created the world's largest delta, which covers 30,000 square miles. Abutting East Asia are the Sea of Japan, Dong Hai, Nan Hai, Bay of Ben-gal, and Arabian Sea. In the Southern Hemisphere, there is the Indian Ocean and the South Pacific Ocean. The Continental Shelf adjacent to the region constitutes a large proportion of the world's readily accessible shelf area. On the other hand, the Philippine and Java trenches and, further out, the Mariana Trench reach to formidable, abyssal depths, downward to 6,000 fathoms. Contrasting to this is Mount Everest, which reaches a lofty height of 29,028 feet. And then there is Xizang, whose high plateaus have been called the roof of the world.

Jan 1, 1992

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

By R. E. Brewer

A critical review of the numerous test methods that have been devised for measuring the "plastic" and "swelling" properties of bituminous coking coals and the practical evaluation of the data obtained has long been needed. The author appreciates fully, first, the arduous problem of doing justice to the merits and limitations of the many original test methods and their manifold modifications and, second, the more difficult task of interpreting the test data obtained in their practical applications to the important problems involved in the coking process. It has been the constant aim of the author to point out the broader significance of the test principles employed in the different classes of test methods and the usefulness of the test data obtained in relation to the problem of coking bituminous coals, rather than to stimulate unduly a controversial criticism of the merits and limitations of any particular class of test methods or of individual test methods devised by different workers. The task has been quite difficult because of the almost total lack of accepted test standards and specifications.

Jan 1, 1942

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By J. William Ganser

This paper is one of a series being prepared by the United States Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

By A. L. Service

In 1965 the Western phosphate industry ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock and phosphate rock products. It has become an important regional industry and, since the close of World War II, it has become important in the national phosphate economy. This report includes an evaluation of the trends and outlook for the Western phosphate industry through 1975 as part of the Bureau's program to determine the rate at which the Nation's mineral resources are being utilized. The first part of this report is concerned with the relationship between the Western phosphate industry and that of the United States and the world. It describes the principal phosphate deposits and discusses production, export, and import of phosphate rock and marketable products. The second part of the report is concerned with the Western phosphate industry and discusses trends and outlook through 1975. Projections for the utilization of phosphate rock, phosphate fertilizers, and elemental phosphorus have been developed and extended through 1975 in an effort to provide data and information pertaining to the rate of depletion of the Nation's phosphate resources.

Jan 1, 1967