Search Documents

By R. F. Favreau, Favreau Patrice

"The economy profits from the rock excavated in mines and quarries and the excavations required for the construction of roads and buildings. However such excavations are achieved by blasting withexplosives, and explosions create fly rock and vibrations which in some cases may throw rock far intoinhabited regions and may vibrate buildings excessively in these regions. Society, however, no longeraccepts that their quality of life be disturbed by the risks of fly rock or the perturbation of vibrations.Thus it is important to know how to design blasts that do not cause excessive fly rock or vibrations, and to understand why sometimes a blast does create excessive vibration or fly rock. An article presented at the 2015 ISEE (reference 1) explains how unacceptable vibrations can be avoided, while the present article explains why dangerous fly rock occurs and how it can be avoided. The article shows by rigorous calculations with the blast simulator Blaspa that long range fly rock can be due to short collar or short burden, but mainly it explains how inadequate blasting that allows the floor to rise can cause even further reaching fly rock, a situation not usually recognized by most blasters."

Jan 1, 2016

By Douglas Rudenko PG, Jay Elkin, Siavash Mahvelati Ph. D.

Very little studies have investigated the behavior of cracks in unlined tunnels over long periods of time, especially when such flaws are subjected to blast-induced vibrations. Using a pool of 30+ blast events, a positive correlation was found between the peak particle velocity and peak crack movement.

Feb 1, 2020

By David E. Siskind

In the early 1980's, the Bureau of Mines published four reports of structural response and damage from surface mine blasting, vibration monitoring, and analysis methods. These findings replaced simpler and less restrictive Bureau criteria dating back to 1962 for ground vibration and 1943 for airblast.

Jan 1, 1991

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

By L C. Taylor, H U. Lesiste

This paper provides a preliminary description of the properties of the output pressure (shock) wave of an end initiated, cylindrical charge of low height to diameter ratio in saturated sand. The properties of primary interest are the pressure wave velocity, peak pressure and rate of rise of peak pressure to within 1.4 charge diameters from the output end of the charge. The behavior of these properties is seen to be quite different from their behavior at more customary ranges in water.

Jan 1, 2013

By G. Cavanough, A. Torrance

Emulsions have been developed for over forty years to become the most common water-resistant explosives used in the mining industry. An emulsion is a common commodity, with many examples in our day to day lives of one immiscible liquid dispersed in another. They have varying degrees of stability from a few seconds to years. What makes their application in explosives unique is twofold. They contain a high concentration of salts in the dispersed phase and also have a far larger volume of dispersed phase than continuous phase. The continuous phase contains at least 75% by weight of an oxidizer such as ammonium nitrate dissolved in water. The crystallization point of these solutions is often >60oC which means that the formation of the emulsion has to occur at an elevated temperature. Once the emulsion is cooled, its structure helps to prevent the formation of crystals in an otherwise unstable system. At room temperature there is a considerable potential for the small oxidizer droplets to crystallize which is countered by the strength of the oil layer and also the size of the emulsion droplet. If the emulsion droplet is too large then crystals can form which may lead to rapid deterioration of the emulsion and overall crystallization, accompanied by a temperature rise as the heat of crystallization is released from the emulsion. The size of the emulsion droplet is critical in preventing crystal growth and subsequent droplet coalescence and emulsion break down. One method of examining emulsions and understanding their structure is to use optical microscopy to measure droplet size and also emulsion deterioration from shearing, temperature cycling and when contaminants are introduced, such as detergents, different oil types, coating agents and dust particles. This paper reports on advanced techniques to quickly assess emulsion quality and stability

Jan 1, 2024

By Joseph Hoang, Nick Reed, Scott Wishart, Michael Lovitt

Marvel Loch Underground forms part of St Barbara Limited’s Southern Cross Operations which is located 360km (224 miles) east of Perth. Southern Cross Operations produces approximately 120,000 ounces of gold each year. Mining occurs in over 8 lodes using a variety of stoping methods including Uphole Benching, Long Hole Open Stoping, and Core and Shell.

Jan 1, 2012

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By Jorge Blázquez, Pablo Ravanal, Paulo Couceiro, Juan Navarro

Blasting performance is influenced by rock mass properties and blast design parameters. From them, the rock is the only variable that cannot be modified, but it can be measured, so that, blast design variables can be adapted to optimize the results. A new methodology to assess rock mass quality from drill-monitoring data from both autonomous and manual rotary drilling modes is described to guide blasting in open pit operations. For that, a thorough normalization process has been developed to minimize external influences induced in the data by the rig system for autonomous mode and by the operator intervention for manual mode. Principal component analysis has been used to combine MWD information. Two rock description indexes are derived directly from Measurement While Drilling (MWD) data collected. The first index is a Structural factor that classifies the rock mass condition in three classes (massive, fractured and heavily fractured). The second index is a Strength factor that classifies the rock according to the strength properties. Both indexes have been combined to obtain an overall drilling rock factor along the hole. This has been named by the authors as the X-Rock model.

Feb 6, 2023

By Kris Shukla

Noise and vibration produced by blasting generate curiosity and concern from neighbors. Experiments conducted in Sweden, Canada and U.S.A. have established that fine cracks in the plaster--the weakest part of building components--appear at a particle velocity of 4.0" per second or more. Taking into account the margin of safety, the safe zone criteria of 2.0" per second has been established.

Jan 1, 1978

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By Ethan Steward, Robert Eades, Kyle Perry

Shock tubes, either gas or explosively driven, are often used for physical modeling of free field explosions or arena testing. The use of shock tubes often requires less setup time of subjects and smaller driving forces to create pressure versus time waveforms similar to that of arena testing. However, the effects of the shock tube cross sectional geometry on waveform properties is uncertain while free field explosion wave propagation and estimation is well studied.

Jan 1, 2018

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Pablo Segarra, José Ángel Sanchidrián, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD) data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al. (2018) and Navarro et al. (2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave- in rock and cavity. From it, an application for the geotechnical rock condition of orebodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting.

Feb 1, 2020

By Robert Hopler

Blasting powder is a slow-acting, black, granular explosive made of sulphur, charcoal and either potassium nitrate (saltpetre) or sodium nitrate. The blasting powder containing potassium nitrate is known as “A” blasting powder; that containing sodium nitrate, as “B” blasting powder. “A” blasting powder is a little denser, a little stronger and a little less hygroscopic than “B” blasting powder.

Jan 1, 2014

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By D. Scott Scovira, Thomas Gustavsson

The potential of hydrogen peroxide explosives was introduced to Thomas Gustavsson and Robert Håkland by Dr Miguel Araos through his development of hydrogen peroxide gel compositions (HPG). In 2020, Thomas and Robert developed a concept project with Boliden Minerals and received Swedish government funding to evaluate HPG technology in a mine environment. The project showed HPG reacted violently with mine mineralization and concluded that HPGs did not offer a commercial solution due to safety concerns. Thomas and Robert engaged with Stefan Nilsson to develop hydrogen peroxide emulsion (HPE) compositions and the process techniques to manufacture them. In 2021, laboratory work produced a promising low carbon intensity, nitrate free, ammonia free, emulsion formulation based on industrial grade hydrogen peroxide and a fuel-emulsifier phase. Design and construction of an HPE pilot plant and underground charging unit commenced. The manufacture of hydrogen peroxide emulsion shares several similarities with the production of nitrate-based emulsions in that the plant is a facility to blend a strong oxidizer solution with a liquid fuel phase into a finished emulsion. A key differentiator between HPE and nitrate-based emulsion is that the manufacture of HPE is a cold production technology in that neither the oxidizer phase (HP) nor the fuel-emulsifier phase requires high temperature heating to prepare raw materials. A successful proof-of-concept HPE evaluation ran from April 2022 to October 2022 at Boliden’s Kankberg underground mine in Sweden. This evaluation demonstrated HPE technology's safety, performance, production, handling, and indicative environmental benefits.

Jan 21, 2025

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012