Search Documents

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By Graeme J. Jameson

In conventional flotation machines, the recovery is strongly related to particle size. As particle size increases, the recovery also increases, reaching a maximum in the range 20 to 120µm. Beyond this range however, the recovery declines quite quickly. The reason for the decline in recovery observed with coarse particles can be traced to the effect of turbulence. Bubbles trapped in turbulent eddies rotate rapidly, and when the centrifugal force on a particle exceeds the retaining forces due to surface tension, the particle detaches. Since the centrifugal force varies as the cube of the diameter of the particle, and the attachment force varies simply as the diameter, being proportional to the length of the contact line, it is clear that detachment forces will predominate as the particle size increases. The corollary is that the recovery of coarse particles can be improved if the level of the turbulence in the cell can be reduced to a minimum. In this paper, a new type of flotation machine will be described, in which the particles to be floated are suspended in a fluidized bed. An up flow of fluidizing water is provided, by recycling liquid from the top of the cell. The recycle stream is aerated in a high-energy device that disperses the air into fine bubbles that capture the fines and ultrafines. Results are presented for several minerals and coarse coal. Keyword: fluidized bed flotation

Sep 1, 2012

By S. Mohanta

The air dense medium fluidized bed separator which has been developed for the dry beneficiation of coal is recognized as a low cost and high efficiency process. The success of this separator for beneficiating any specific coal, alone or in combination with other processing methods, mostly depends on the characteristics of run-of-mine coal. Therefore, a thorough knowledge of the mineralogical composition and washability characteristics of representative coal sample is highly essential for correctly and effectively assess the suitability of this process. Available literature conforms that although the characteristics of Indian non-coking coals are well known, the correlations between the particle compositions with its density are entirely lacking. In the present study the washability, proximate, ultimate and elemental analysis was conducted for four typical Indian high-ash non-coking coals and their elemental compositions were well correlated with the specific gravity of coal. The results obtained in this study provide some essential information to the coal-processing engineer for efficiently operate and control the process. Furthermore, the beneficiation potential of air dense medium fluidized bed was experimentally evaluated and compared with the results obtained from an operating wet beneficiation plant. Based on this comparative study the air dense medium fluidized bed is established to be a possible alternative to the conventional wet beneficiation method for beneficiating Indian coals with Ep values in the range of 0.03 to 0.06

Sep 1, 2012

By Nicolás Luis, Qi Liu, Gonzalo Montes-Atenas

"The prediction of froth flotation performance is still an unresolved topic. Classic industrial models based on particle size, elemental and mineralogical information provides recovery results with deviations that may become significant. One possible reason for this deviation may be the fact that the current liberation analysis provided by electron microscope based techniques does not take into account the outmost surface layer composition of liberated particles. In order to complete the description provided by the liberation analysis, other spectroscopy techniques measuring the extreme surface of the minerals can be tested. For instance, X-ray Photoelectron Spectroscopy (XPS) is a technique which measures the first tens of nanometers providing elemental composition over the particle surface and allows resolving the elemental associations present at the surface sample. However, this information needs to be statistically robust, reproducible and most importantly representative of what is occurring in the process. The aim of this research work is to develop a statistical model based on particle population to evaluate the feasibility of turning the XPS technique into a metallurgical tool. The model consists of classic statistical population arranged in a bed of heterogeneous particles with a known grade and mineral liberation. The simulations showed that the XPS results statistically followed a well-defined pattern. The statistical results were confronted with pilot plant results obtained from a rougher bank when processing a copper sulfide ore from a Chilean mine site. It was observed that the probability function distribution was in agreement with the experimental data. Further analysis on how the XPS results provide valuable information improve the computation of froth flotation recoveries is also discussed."

Jan 1, 2014

By Andrey V. Tarasov

"An environmentally clean and virtually waste-less technology for treatment of domestic and industrial solid waste (HGIW) including other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations.The essence of the process is that the HGIW are decomposing in the liquid base in air-bed slag melted layer under the temperature of 1350-1400°C.HGIW is considered as fuel heat-producing energy of 1500-1800 kCal/kg with 51,7%.Processing of municipal and industrial solid waste in molten slag is carried out autogenously without additional fuel, the blowing is enriched by oxygen up to 50-70%.The complex makes it possible to treat the furnace charge without preliminary drying and sorting with big differences in chemical and morphological composition due to the versatile firing chamber.The proposed process resolves the acute and globally significant problem of dioxin formation.The purpose of the proposed technology is to ensure such destruction of the structural lattice that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. It was established the required preconditions to achieve this purpose."

Jan 1, 2003

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By Wieslaw Wszolek, Kazimierz Trybalski, Ryszard Tadeusiewicz

"The present work is an attempt of neural networks application to the description of complex technological processes of useful minerals enrichment. Neural networks are among the most convenient tools that have been added recently to the professional toolbox of modelling specialists, and they are particularly useful in realisation of multiple practical tasks, characterised by great complexity and relatively low amount of available a priori knowledge about the nature of the modelled processes. They are successfully applied in a wide variety of problems related to data processing and analysis, their prediction, classification or process control. The object of the study was the technological site for copper ore enrichment by floatation, being a part of technological line in the Ore Enrichment Plant ZG „Polkowice”, KGHM „Polska Miedz” S.A.The main floatation is described by parameters measured by the supervision and control system, which can be grouped with respect to the functions performed for the object:a) input function: aFG - copper contents in the feed material for the main floatation [% Cu]b) control: LFG I - level in the first section of the floatation unit [%], LFG II - level in the second section of the flotation unit [%], LFG III - level in the third section of the floatation unit [%], LFG IV - level in the fourth section of the floatation machine [%]. These quantities compose the five elements long input vector.c) output function: ? - copper contents in the waste from main flotation (final waste) [% Cu]The measurement data, containing the above-mentioned parameters, have been collected during the normal operation of the plant. The data contain momentary values of the parameters, registered every 10 minutes, covering the period of 196 hours of the plant’s operation (1176 measurements for each quantity).For construction of the model used in the study classical multi-layer perceptron-type neural network has been used, with one hidden neuron layer, trained by the error back propagation method."

Jan 1, 2003

By R. Weyhe, B. Friedrich, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990's. In 1999 the output of cells exceeded 80,000 tons per year (1 billion cells per year). Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps.After shredding the steel shell, the various fractions of battery materials are carefully separated by mechanical processing. A hammer mill with one rotor with a perforated discharge grid of 20 mm opening, was found to be suitable for crushing the batteries to release the active mass of electrodes for metallurgical processing. The ground material is wet screened at a mesh size of 0.5 mm; thus a fine fraction is obtained with valuable components such as Ni, Co, and RE and an oversized fraction consisting of a mix of iron chips, electrodes grids, plastic chips, paper, and flocculent material of separators. The organic components are avoidable when there is a thermal step at the beginning of processing batteries.The separated fine fraction is smelted in an electric arc furnace. Any pyrometallurgical process relies on a suitable slag system. In this specific case, the process has to allow separation of nickel and cobalt as metal from the rare-earths almost quantitatively, collecting the rare-earths as well as impurities e.g. as oxides. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’."

Jan 1, 2003

By Ricardo Duque-Soto, Gonzalo Montes-Atenas

The depletion of water resources has posed an enormous challenge to the continuity of many mine sites, particularly those located in arid zones worldwide. In Chile, the use of seawater has been foreseen as one possibility to solve this problem. Nevertheless, the direct use of high ionic strength solutions such as those present in the sea has been found to have some drawbacks. Specifically, rhe extraction of copper from complex ores using high ionic strength solutions such as that of seawater has become one of the most relevant topics in the field of copper hydrometallurgy. This study aims to determine the effect of the degree of salinity on copper extraction kinetics in mixed oxide-sulfide ores. A leach protocol was implemented to study the extraction kinetics, varying the degree of salinity of the medium and the temperature. A thermodynamic model was developed to explain differences in the metal extraction. It was found that the ionic strength impacted positively the copper extraction, probably due to the reduction of the effective concentration in solution due to ionic interactions enhancing the diffusive mass transport of copper ions. This effect is observed to be enhanced when up to an overall salinity values close to 20gpl.

Jan 1, 2014

By Georg Unland, Thomas Wegner

"Impact crushers are widely used in different industries to crush materials which can vary from soft to hard and from ductile to brittle. However, the sizing of impact crushers is still based rather on empirical than on scientific approaches. Therefore, a test rotor was developed in order to investigate the principles of comminution by impact. Rocks of diabase with different diameters were used to gain the crushing properties with the following results:RESISTANCE AGAINST CRUSHINGLikelihood of BreakageThe likelihood of breakage is a function of the impact velocity and the particle diameter. The likelihood increases with higher velocities and larger diameters. Maximum Crushing ForceThe crushing force is related to the area of projection of the rock. The smaller the particles and the higher the velocities the larger are the maximum related contact forces.Contact TimeThe contact time increases with the rock diameter whereas the influence of the impact velocity is neglectable.Mass Specific Crushing WorkThe mass specific crushing work decreases with the particle diameter and increases with the impact velocity."

Jan 1, 2003

By D. P. Hatfield, G. de Jager

"Recent developments in image analysis techniques and the power of computer hardware have spurred international interest in the potential uses of image analysis techniques in a range of industrial applications. One of these applications is the control of the complex flotation process. Despite years of work, the flotation process is still poorly understood. Current attempts to control flotation cells focus on consistently duplicating the control achieved by human operators.In human control of flotation two of the dominant visual cues are the froth flow speed and the froth stability. These two factors can be measured and inferred respectively from image analysis of video of the froth surface. Two important hydrodynamic variables for control of the flotation process are the air addition rate and the level of the froth pulp interface.The current work focuses on the relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell. Results are presented that show a strong relationship between flow speed and concentrate yield. These results include tests where the conditions in the cell were not changed, as well as tests involving changes to the cell level and air addition rate. Preliminary results are presented which show a correlation between froth stability and froth percent solids.Future developments of the system will include comprehensive froth texture typing, colour space and stability analyses."

Jan 1, 2003

By Paul W. Cleary

"Particle scale simulation of industrial particle flows using DEM (Discrete Element Method) offers the opportunity for better understanding the flow dynamics leading to improvements in equipment design and operation that can potentially lead to large increases in efficiency, throughput or product quality. DEM has been used for modelling many industrial applications, particularly milling. This includes ball and rock motions and power consumption in ball mills, AG and SAG mills, vibrational segregation, flows in rotating drums, operation of dragline excavators and hopper flows. In mineral processing, DEM has been concentrated on mills because of their critical importance. However DEM also offers the opportunity to improve many other parts of mineral processing operations. These areas often do not receive the attention that the key comminution equipment commands, but can become critical when they fail or under-perform. Importantly their assessment/improvement using DEM is often much more feasible because of smaller problem sizes and the absence of poorly understood physics such as breakage. In this paper we describe DEM simulations of four important pieces of non-comminution equipment that are commonly found in or near mineral processing plants (these are shown in Figure 1):"

Jan 1, 2003

By Fu Ping-Hao, J-P Franzidis, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton's Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By Paula Olea, Gonzalo Montes-Atenas

Froth flotation operation is a large tonnage process aiming at selectively separate economically valuable minerals from gangue material. The wellbeing of an industrial froth flotation operation has been historically assessed and understood in terms of many variables known to somehow affect the process performance. Among these variables, air dispersion have been pointed out as key to secure the correct transport of hydrophobic particles to the froth phase and, then, to the concentrate. One of the classic parameters assessed when evaluating the air dispersion in flotation tanks is the superficial gas velocity. Many reports have focused on studying the superficial air velocity profiles across the pulp phase and theories have been based on the fact that the measurements should be performed in the so called "quiescent zone", which is a volumetric region inside a flotation cell of difficult determination. The hypothesis behind this research work is that the reporting of particles to the concentrate would provide a better correlation with the effective air flowrate pattern created in the froth phase. The aim of this study, as a first step towards developing a flotation model fully froth phase-based, is to estimate the effective surface area used in a flotation cell derived from results obtained with a specific setup at laboratory scale. The methodology considers running a thin lateral flotation cell cut at different superficial air velocities, with and without particles. It was found a non-linear correlation between the superficial air flow rate and the characteristic distance between the vertical wall next to the cell lip and the cut point where the foam or froth flowrate almost stops contributing marginally to the overall amount of solid particles transferred to the concentrate. The presence of hydrophobic particles reduced the mobility of the froth phase reducing the characteristic distance.

Jan 1, 2014

By Alejandro Rubio-Lopetegui, Gonzalo Montes-Atenas

The occurrence of Enargite (Cu3AsS4) in hydrometallurgical plants bears a number of challenges. One question lies on how Copper and Arsenic can be selectively extracted from the solid surface structure when immersed in aqueous solution. The leaching of Enargite in ambient conditions has been extensively studied; nevertheless, challenges regarding the process kinetics and surface structures enabling the extraction process remain ill-understood. Prior knowledge indicates that different conditions of pH, Eh, temperature, speciation of the aqueous phase or variations of these parameters defines the overall rate at which metals and other elements will be transferred to the solution. One aspect that the research studies have seldom addressed involves studying the main features of the surface structures formed during the leaching process at the outmost surface atomic layer. Such structures will mediate between the solid bulk and the solution to undertake subsequent stages of leaching process. The aim of this research work is to critically analyze the state of the art of Enargite electrochemistry from the mediator formation-dissolution mechanisms standpoint occurring at the mineral-solution interface. The most probable mediator species reported in the literature were found to be: Arsenolite and Sulfur (acidic media), Covellite (acidic and alkaline media) and Tenorite (alkaline media). As a result of this analysis, it was observed that the surface speciation was not in full agreement with the previous knowledge suggested to explain Enargite leaching reactions and, therefore, modified Eh-pH diagrams are presented. The acquired insights on the surface structures rising from the Enargite-aqueous solution interactions is further revised to provide new experimental protocols towards selectively separating Copper and Arsenic through hydrometallurgical paths.

Jan 1, 2014

By Susanna A. C. Stadler, Chris Aldrich, Jacques J. Eksteen

"Slag foaming occurs in several pyrometallurgical processes. These processes include steelmaking in basic oxygen steelmaking furnaces and electric arc furnaces as well as various non-ferrous operations like sulphide smelting/converting and base metal slag cleaning. Although slag foaming in steelmaking processes has been extensively researched, little attention has been given to slag foaming in non-ferrous operations. Slag foaming phenomena are complex because often the system consists of three or more phases. With this in mind, factors previously identified as influencing slag foaming were investigated. These include the slag basicity, physical properties of the slag, namely viscosity, surface tension and density, the formation of particles due to undercooling of the slag and the FexO concentration in the slag.Slag foaming was investigated in a vertical tube furnace. The different slags were contained in alumina crucibles and bubbling argon gas through the molten slag induced foaming. The foam height was measured by using stainless steel probes and a voltmeter. The conductivity of the slags made it possible to measure the foam height from the position of the probes when the electrical circuit was completed. Slags were foamed at different temperatures to investigate the effect of solid precipitates.The effect of increasing FexO concentration was found to decrease the foam index due to lower viscosities, but higher surface tension depression appears to have led to increased foam index values at high FexO concentrations."

Jan 1, 2003

By Katsunori Okaya, Toshio Inoue

"Movement of mill charge in the centrifugal mill is essentially dissimilar from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. This dissimilarity is the reason for the substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Bradley et al. (1983) developed a math model regarding the mill charge as a lump. This model is presented in a simple equation with which motion of the mill charge can be predicted in terms of the parameters describing the specification and the operation of the centrifugal mill. This equation can be used to explain the power draft of the mill as well as the stability of mill operation. More recently, on the other hand, a numerical simulation technology called discrete element method (DEM) has become a vital vehicle for estimating the motion of the grinding media in the mill. The authors developed a mill simulator called ‘Mill Solver’. Mill Solver is designed to simulate various types of mills including centrifugal and vibration mills. The principle of this simulator is to calculate individual kinetic events of interaction of balls in the mill in a minute time interval, hence the mill performance can be constructed for estimation."

Jan 1, 2003

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"The effects of mixed collectors on some physicochemical parameters (thin film lifetime, kinetics of expansion of the three-phase contact, equilibrium three-phase contact angle and surface tension) involved in the elementary act of flotation were investigated experimentally.We have used the microscopic thin balance developed by Scheludko et al (1970) to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates at 1:1 molar ratio. The experiments were performed at a range of concentrations at pH 6.5. The equilibrium contact angle was measured with a microscope technique using the modified Mingins-Sheludko method (Mingins and Scheludko, 1979). The surface tension was measured by the method of Wilhelmy (Adamson, 1960). It was found that the mixed surfactants caused lower contact angles, lower rates of the thin film rupture and longer film lifetime, compared to the pure amine system."

Jan 1, 2003

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003