Search Documents

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By Rod Hocking, Nenad Djordjevic, Randolph Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures of operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill.Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulated the assemblage of a physical mill."

Jan 1, 2003

By A. N. Zagorodnyaya, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva, A. S. Sharipova

"In Kazakhstan, there is a unique sulphide copper deposit, in the ores containing the natural isotope of osmium-187 (more than 90 %). In the pyrometallurgical processing of concentrates for the target metal, osmium is mainly sublimated, with wet cleaning of metallurgical gases (dust and gas mixture) 40 % of it together with rhenium passes into washing solutions (wash acid). On the basis of this acid, the production of ammonium perrhenate was organized at the enterprise of the RSE ""Zhezkazganredmet"" and for the first time in the world practice - the isotope of osmium-187. However, the degree of its recovery from solutions does not exceed 8 % of the amount supplied with the charge or 25 % of the amount that was received for extraction. But the bulk of it (~ 75 %) remains in the raffinate, discharged to sewage treatment plants (wastewater). The studies presented in this work are aimed at solving the problem of osmium isotope-187 extracting from wastewater, which are a potential source of increasing metal production in Kazakhstan. The aim of this work is the development and scientific justification of osmium deposition regimes from wastewater using such reagents as thiosulfate and sodium sulphide. The influence of various physicochemical factors on the precipitation of the osmium was studied and optimal conditions for its maximum transition to sediment were chosen. An original method for obtaining osmium concentrate in the presence of sodium thiosulfate with the addition of potassium iodide from a new type of wastewater - man-made ammonia solutions has been developed. These solutions were combined mother liquors of solid-phase stripping operations and dissolution of pulp of crude ammonium perrhenate. On the basis of the obtained results, a settling technology for extraction of the osmium from man-made ammonia rhenium-containing solutions was introduced at RSE ""Zhezkazganredmet"". It should be noted that the degree of extraction of osmium, depending on its concentration in solutions entering on the settlement, and taking into account the addition of sulfuric acid, will vary from 60 to 90 %. The recovery of osmium during the test period was 58 %."

Jan 1, 2018

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By Andries Van Wyk, Steven Bradshaw, Guven Akdogan, Jacques Eksteen, Cornelius Snyders, Cleophace Mpinga

"In order to exploit lower grade and complex platinum group metal resources, cheaper and more efficient alternatives to the conventional mill-float-smelt-refine route are being sought, particularly for resources’ in areas that are water-scarce and where electrification is costly and problematic. Leaching with cyanide is a promising process option and although recoveries are lower than in the conventional process routes, progress into the understanding of cyanide leaching of PGM containing ore and concentrate has been made. Research regarding the feasibility of upgrading the pregnant PGM leach solution using activated carbon has, however, been lacking and hence forms the focus of this paper. Bottle roll adsorption tests for dilute PGM solutions (0.15ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) onto granular activated carbon showed high rates within the first 60 minutes (giving more than 90% recovery of precious metals). Comparison of the Pt isotherm to Au isotherms from literature indicated a similar loading capacity, while that of Pd was found to be significantly lower. The effects of solution pH, temperature, base metal concentration, free cyanide concentration, thiocyanate concentration, initial PGM concentration and activated carbon concentration were investigated and are discussed. Elution of the Pt and Pd, with the AARL elution process, was found to be effective with recoveries of 95% after 5 bed volumes of eluant at the optimum pre-treatment concentrations and a temperature of 80°C. Temperature, NaCN and NaOH pre-treatment concentration and the ionic strength of the eluant were found to be the most important factors affecting elution while base metals concentration, acid-pre-treatment, carbon loading and thiocyanate concentrations to a lesser extent. Simplified combined flow sheets are suggested and the corresponding mass balances are compared."

Jan 1, 2014

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012

By J. Yianatos

The cleaning circuit operation and its effect on the plant metallurgical performance, was characterized at Los Pelambres concentrator, Chile. Experimental data from columns, scavenger and regrinding stages was evaluated. Each stage was characterized by size fractions, and the interaction between stages (columns, scavenger, regrinding) as well as the effect that circulating loads had. The approach for describing the flotation equipment operation (cells and columns) considered the collection and froth zones separately. This methodology allows for the identification of the impact that particle size distribution has on the actual collection and froth transport processes, independently. In this way the effect of regrinding on flotation recovery and grade can be related to the corresponding operating variables, e.g. pulp flowrate, air flowrate, pulp level and pulp density, among others. The effect of gangue entrainment was considered using an empirical dimensionless correlation. The interaction between the circulating load and the overall performance of cleaning circuit was evaluated. The circulating load was defined as the ratio between the solid flowrate of scavenger concentrate over rougher concentrate. It was found that the overall cleaning flotation circuit (column-scavenger) can operate at a relatively high and constant recovery for a wide range of mineral treatment. This is possible when the scavenger has the capacity for compensating the decrease in column recovery at larger circulating loads. Under the condition of high overall cleaning recovery, the rougher stage closely represents the plant recovery. However, at large mineral treatment conditions, the design characteristics (e.g. concentrate transport channel capacity and transfer boxes) as well as instrumentation, control facilities and operation, became bottle-necked. A simulator was developed using empirical models for each stage (column, scavenger and regrinding) in order to evaluate proper operational strategies for cleaning flotation circuits Keywords: flotation, cleaning, regrinding, Vertimill, simulation.

Sep 1, 2012

By Jun Qiu, Ping Chen, Xianjun Lu

Nitrogen of different forms from wastewater was adsorbed by the natural bentonite and modified bentonite. The effects of adsorption conditions on the nitrogen removal were investigated. The experiment results showed that natural bentonite could easily adsorb ammonia while poorly adsorb nitrate, the organic bentonite modified by octadecyl trimethyl ammonium could effectively adsorb nitrate with the removal ratio increased from no more than 5% to 89%. Two kinds of bentonite were added together to the simulated wastewater which contained ammonia nitrogen of 15mg/L and nitrate nitrogen of 10mg/L, the dosages were 1.0g respectively. Both ammonia and nitrate had significantly decreased on conditions that the oscillation time was 1.0h and room temperature 20?. The optimum pH value for ammonia removal was 7 while for nitrate removal was above 7. The adsorption isotherm fitting results indicated that the Freundlich adsorption isotherm was the better model to describe ammonia adsorbed on the natural bentonite and the saturated adsorption capacity was 10.25mg/L, while the Langmuir isotherm could better describe the adsorption of nitrate on the organic bentonite and the saturated adsorption capacity was 14.35mg/L. Fully considering the interaction between different ions and controlling the appropriate conditions, removing nitrogen from wastewater by adsorption of bentonite is an economic and effective method.

Jan 1, 2014

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By Z. K. Liu

Production of the amines collectors and cation surfactant gives out the liquid waste containing high COD (Chemical Oxygen Demand) and ammonium & nitrogen, which is difficult to be treated with conventional biological method to reach waste water discharge standard. In this paper an engineering practice of treatment on the liquid waste by the technology combined high effective microbe with A/O (Anaerobic& aerobic) process is presented. The quality of treated water comes up to class A national standard for discharging.

Jan 1, 2014

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Gauti Asbjörnsson

Material handling is an essential part of the aggregate and mining industries. Mixing and blending of granular material can affect the grading and particle size distribution of the material leaving the system. Segregation and variability can cause problems in the downstream process while insufficient capacity will disturb upstream processes. Process plants utilize surge bins for handling recycle streams of material and act as a buffer for the process. The flow through the surge bin is usually controlled by a simple PID controller or PID controller in combinations with a plant-wide controller. Even though the surge bins play an important role of smoothening out the plant and creating a steady operating condition they are seldom included in plant simulations. This can lead to a number of problems in the form of decreased plant capacity, plant lockdown, and even operation units malfunctioning. The main objective of this study is to investigate the dynamic behavior in surge bins and develop a model more suitable for representing this behavior, which can occur during operation, for dynamic simulations. The proposed model adopts vertical layers which allow for flows between segments depending on the level of neighboring segments. This enables both the representing of segregation within the system and gives an indication on the effects from different inlet- and outlet placements. The proposed model was developed in MATLAB/Simulink and validated against an actual bin with the total capacity of 660 m3 in platinum ore application. With the new bin model significantly higher fidelity and more accurate dynamic, simulation results were achieved. Keywords: dynamic simulation, modeling, segregation, material handling, MATLAB/Simulink

Sep 1, 2012

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012