Search Documents

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013

By S. G. Shabestari

In the metal casting industry an improvement of component quality mainly depends on better control over the production parameters. Thus, thermal analysis cooling curve of the alloy is used for process control in aluminum casting industry. Cooling rates of the alloy during solidification process affect microstructure, grain size, eutectic silicon morphology, and dendrite arm spacing (DAS). In this research, effect of cooling rate on the microstructure and solidification parameters of 319 aluminum alloy that is a widely used alloy in automotive industry, has been investigated by means of thermal analysis. Seven different cooling rates have been obtained by using CO2-bonded silica sand molds with two different wall thicknesses, hot-work tool steel molds (H13) with and without coating, thin-wall steel molds with different coatings. In each case, cooling curve and first derivative cooling curve have been plotted by use of very accurate thermal analysis equipment. Effect of different cooling rates on solidification parameters e.g. Nucleation temperature (TN,a), nucleation undercooling (ATN,a), recalescence temperature (TR,a), solidification range (AT,s), and total solidification time (t 0 have been studied in the liquidus region. Microstructural evaluation has been carried out and DAS were measured in all solidification conditions. A numerical equation was proposed to predict cooling rates via measuring DAS in 319 aluminum alloy. Nucleation process and the effect of cooling rate have been interpreted by using thermal analysis cooling curves and microstructural study.

Jan 1, 2004

By Dennis Z. F. Mraz

"Because rock salt and pot ash formations contain particles capable of elastic deformation, the material has usually been compared with various rheological models containing elastic elements. Extensive laboratory testing of salt and potash samples resulted in various theoretical conclusions based on conditions quite different from those in a deep mine. It is felt that sufficient data have now been collected from underground measurements and observations to demonstrate the inelastic behaviour of salt masses in a deep mine. The conditions in deep salt strata can be defined as near hydrostatic, because the acting pressures are very high compared to the negligible elastic limit of the salt. The pressure field and creep around the single opening is a function of its shape, size and age. The same factors, together with extraction, determine the behaviour of the mining a rea. The application of the correct analytical method in mine design can significantly improve the excavation techniques and predetermine the long-term behaviour of openings."

Jan 1, 1973

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

Energy benchmarking is widely applied across industries to determine the potential to improve energy performance. Unlike the many technologies for which energy benchmarks and efficiency rating systems are already in maturity, benchmarking of mining processes is still in its infancy. Benchmarking energy usage in mining operations, where energy costs are high and represent a significant portion of overall operating expenses, is challenging due to the uniqueness of each mining operation. Mines vary in terms of geology, geographic setting, ore body geometry, mineralogy which impact the mining method, material handling, processing and waste management. In order to gauge the opportunity for reducing the energy intensity of individual operations and also to compare the energy performance of operations on a global scale, the deployment of new benchmarking methodologies, models and frameworks is necessary. As a step towards the establishment of an accurate framework for benchmarking the energy consumption of mining operations, comminution, one of the more energy intensive mining sub-processes, was selected as the focus of a new energy benchmarking method. The methodologies and processes used to onset fragmentation in a rock mass to the crushing or grinding of rock to a size that is suitable for economic extraction are predominantly dependent on the ore properties. For this reason, site specific factors, such as the size reduction requirements and ore hardness were included in an energy benchmark model so that the energy performance of comminution processes at different operations could be normalized and compared on a global scale. Single particle compression breakage has been identified by several prominent researchers in the field of comminution as the upper limit of energy utilization in size reduction processes. For this reason single particle compression breakage was proposed as the basis of a work index for ores to be used as an input for the benchmark model. Overall, the new method showed that the energy benchmark for mineral comminution can be normalized and subsequently compared for a range of mining operations once the ore hardness has been appropriately characterized.

Aug 1, 2013

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By Nur Hossain

Analysis of Linear Elastic Fracture Mechanics (LEFM) parameters via the Virtual Crack Closure Technique (VCCT) has been obtained for SENT specimens of AM6OB magnesium alloy. It is found that the ratio of initial crack length to initial monotonic plastic zone size is one of the critical factors in establishing the limit of using LEFM concepts. If this ratio is below a certain limit (i.e. when crack lengths are small in comparison to the plastic zone size), loss of similitude stress intensity factor range would occur. This ratio, therefore describes the limit below which the use of LEFM would no longer be admissible. In this study, the above limit was established for AM6OB magnesium alloy. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determination of the coefficients of Paris model.

Jan 1, 2010

By S. N. Aliferova, E. I. Afonina, S. N. Titkov, A. Ju. Bondareva, N. N. Panteleeva

"Potash ore is mainly processed using the method of cationic flotation. Potash ore deposits of the CIS, namely: at Upper Kama river, Gremyachinsk (Russia), Starobin (Belarus), Tubegatan (Uzbekistan) are characterized by relatively low KCl impregnation (1.0 – 1.5 mm) and contain up to 10% of waterinsoluble impurities (WII). Water-insoluble impurities are presented by aluminosilicate, silicate, carbonate (calcite, dolomite) minerals and anhydrite. In the process of milling the ore to a flotation size there are released and dispersed the insolubles impurities actively sorbing the cationic collector, i.e. aliphatic amines C16 – C22. In this regard there is carried out a preliminary desliming of the ore.Currently grinding the ore to a flotation size (1.5 mm or less) is carried out in rod mills along with forming of a large number of fine-grained ore fractions having the size under 0.25 mm, which results in the increased KCl losses with halite slime waste and reduction in the quality of finished product. There has been developed the technique for processing of potash ores with a high content of water-insoluble impurities (10 – 12%) containing, in different ratios, silicates, carbonates and anhydrite. The technology involves the use of the ore dry grinding to the flotation size and subsequent reagent activation of the processes for sludge removal and sylvite flotation.INTRODUCTIONCurrently there are being developed the potash ore deposits in the CIS countries, namely: at Upper Kama river and Gremyachinsk deposits (Russian Federation), Starobin deposit (Republic of Belarus) and Tubegatan deposit (Uzbekistan). Potash ores are a mixture of sylvite and halite and contain water-insoluble impurities of silicates, carbonates and anhydrite. The content of water-insoluble impurities (WII) reaches up to 10%, disseminated (impregnated) sylvite does not exceed 1.5 mm and in connection with that the ore is crushed to a particle size under 1.5 mm. Ore grinding is performed by wet process in rod mills with producing a significant amount of fine-grained mineral fractions and sludge, which are actively sorbing a cationic collector, i. e. primary aliphatic amines C16 - C22. The ground ore is deslimed and the slime product is directed to a sludge depot (pits)."

Jan 1, 2016

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By S. D. Anitha Kumari, T. G. Sitharam

"The huge urbanisation of the world cities have invariably resulted in enormous requirements of development in transport and other facilities. As the surface space available for the construction of these infrastructural facilities is found to be inadequate, underground space is widely used recently for this purpose. However, to understand the behaviour of these underground structures through experiments under various loading conditions is not practically feasible. Hence numerical methods have widely been used to model these structures and predict their behaviour. The underground structures generally rest on soil or rock. Depending upon the properties of the material surrounding the tunnel, the deformation pattern and the stress contours vary. If the tunnels are placed on soft ground at a shallow depth, the presence of existing structures will add to the stresses and strains developed. In the case of densely populated cities, tunnelling operation may result in huge damages if the settlements are not within the desirable limits. This may in turn lead to the collapse of the tunnel along with adjoining structures. So the determination of stress levels associated with the yield of wall due to excavation is very important and necessary supports and reinforcement should be provided. Numerical simulations using discrete element method (DEM) and finite element method (FEM) have been done to understand the stress variation around single and twin tunnels. Studies are also done to quantify the improvement of stability on the introduction of lining around the tunnels in a weak cemented soil mass like sandstone.INTRODUCTIONMost of the life line facilities which include pipelines for electricity, water, communication, sewage, gas, roads, metro, utility tunnels etc in modern urban areas are underground structures. Infrastructure development is crucial for any city and sustainable development urges for underground constructions. Accordingly, there is already a great demand for tunnels to be constructed in difficult and crowded urban settings. This results in the fact that a large number of risk factors are associated with tunnels in these densely populated urban areas. These constraints pose threats to tunnel construction and also demands for minimal disturbance to the public and to the surrounding utilities. One of the most important factor to be considered while designing an underground structure is its stability with respect to the surrounding medium and adjoining existing structures. In this study, a comprehensive presentation of the numerical modeling of single and twin tunnels adopting two different methods is presented."

Jan 1, 2015

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By K. Shikaze

"For the last three years (1967-9) the value of the output of mineral resources in the Province of Ontario exceeded one billion dollars per year. To produce this great wealth, it was necessary for the mining industry in Ontario to dispose of an estimated 80 million tons of waste mill tailings. Some of these tailings were returned underground but the greater proportion was disposed of above ground in lakes, watercourses, marshy areas and in engineered impoundment basins. This volume of tailings, if accumulated in one location would cover an area of 1000 acres to a height of almost thirty feet. The provision of proper disposal of the waste mill tailings in a manner such that they will not create problems in the environment is one of the costs which must be borne from the extraction of such a wealth from our mineral resources. It is principally the potential water pollution which may occur as a result of the indiscriminate discharges of waste mill tailings which is of concern to the Ontario Water Resources Commission.ONTARIO WATER RESOURCES COMMISSIONThe Ontario Water Resources Commission was formed in 1956 and operates under the Ontario Water Resources Commission Act. The Act has been broadened and amended many times by amendments."

Jan 1, 1970

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited available technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "observational construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of a mountain tunnel (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert et al. requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electro-optical distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily management measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this proposed method. It then presents the typical results of a field demonstration test at a tunnel under construction. Lastly, the predictable range from the stratum boundary at which ground stiffness changes are discussed based on the results of three-dimensional numerical analysis.

Jan 1, 2015

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014

By Steve Scott

Outline of Talk Seafloor Massive Sulfides (SMS) and Seafloor Sedimentary Sulfides (SSS) Ocean mining of SMS (Nautilus Minerals) Environmental issues Summary

May 1, 2013