Search Documents

By Vishal Shukla, Prateek Singh, D. P. Chakraborty

"Continuous thickening by an operation called sedimentation is the separation of suspended solid particles from a liquid stream by gravity settling. The primary purpose of thickening is to increase the solids concentration of the feed stream. High rate thickeners are designed specifically to maximise the flocculation efficiency. A detailed investigation has been carried out to understand the influence of ore type and operating parameters such as bed level, bed mass, rake arm torque and flocculent concentration on thickening operation. Tata steel’s Noamundi plant data shows that variation in ore type, and operating parameters are major contributors to fluctuation in thickener performance. A lot of research has been done earlier on thickening operation but effect of ore type and operating variables by using plant data was never touched before.In this context, the performance of thickener was evaluated by daily data to study the influence of ore type and operating variables on thickener operation. Investigation shows that friable ore % in feed mix is proportional to slime density because friable ore is porous & brittle in nature. As a result, friable ore generates more fines/ultrafine during communition process in wash plant. Increase in flocculant concentration and bed mass is showing a positive change on high rate thickener performance Investigation shows that optimum bed mass and flocculant concentration is required to achieve desired pulp density in thickener underflow at different feed pulp density (g/cc).INTRODUCTIONOver the years, Iron Ore Beneficiation at Tata Steel, Noamundi has seen varied changes. Depletion of high grade iron and with increasing iron ore throughputs coupled with lowering of the hard ore a subsequent increase in slime generation, slime management and clear water requirement for wet Plant has thrown up myriad challenges. To overcome these challenges, many improvements initiatives were taken by Tata Steel in last decade. One of the major changes is the recent High Rate Thickener commissioning at Tata Steel Noamundi to cater the high iron ore throughput requirement. Slime reporting to Thickener has increased from 1.4 MTPA 2.5 MTPA over the last few decades. The above changes further aggravate the poor settling and dewatering characteristics of the slurry which is being feed to HRT. Considering the above mentioned constraints and stringent environmental implication proper water management has become a major challenge to reckon with. The thickener is used to increase the concentration of the suspension by sedimentation, accompanied by the formation of a clear liquid. In most cases the concentration of the suspension is high and hindered settling takes place."

Jan 1, 2016

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By The Staff

"SummaryDetermination of uranium in ores may be made by measurement of their radioactivity.The method most commonly used is that of measuring beta radiations with the tray-type beta counter. This will give an accurate uranium determination provided the sample does not contain thurium and that the beta and gamma activities have not been disturbed from their natural state of equilibrium. Such a loss of equilibrium will result from mining the ore or from the weathering of the surface rock.A method is described which eliminates errors due to loss of equilibrium. The beta and gamma activities are measured simultaneously in one simple operation. This method is recommended for assaying samples of products from milling operations and its use is limited only by the presence of thorium in a ratio greater than one part of thorium to twenty parts of uranium.A third method is recommended for the analysis of exploration samples and diamond drill cores, which may be assayed in the uncrushed state.Rapid determinations of a large number of samples is possible with the pressure ionization chamber, which is sensitive to gamma activity."

Jan 1, 1950

By C. D. Anderson, C. G. Anderson, P. R. Taylor

"Rare Earths have become critical for our energy and materials driven society. While primary production must ramp up to fill growing demands, the recycle of these strategic elements must also be initiated. This paper will outline the potentials of and metallurgical technologies employed for Rare Earths recycle from various secondary sources.INTRODUCTIONWhen investigating the recovery of rare earths from secondary sources it is necessary to understand the nature of the sources to be processed. As of 2009, the USGS reports the distribution of rare earths by end use, in decreasing order, was: chemical catalysts 22%, metallurgical applications and alloys 21%, petroleum refining catalysts 14%, automotive catalytic converters 13%, glass polishing and ceramics 9%, rare earth phosphors for computer monitors, lighting, televisions 8%, permanent magnets 7%, electronics 3%, and others 3% (USGS, 2011). Additionally, it is reported that the amount of recycling was quite small and consisted primarily of rare earth magnet scrap, although with the sharp increase in the price of rare earths, and the potential shortage in supply, focus in this area is continually growing. Thus, the opportunities, whether realistic or not, are extremely vast in the recycling of rare earth containing materials. The following subsections will present methods proposed for the recycling of rare earths based on the feed material type.RECYCLING OF RARE EARTH MAGNETSCurrently, investigations are ongoing in the area of recycling production scrap and end-of-life materials in the rare earth magnet industry. The following techniques illustrate potential methods for the recovery of rare earths from secondary RE magnet sources.Recycling of Rare Earth Magnet Sludge by Selective ChlorinationDuring the production of neodymium magnets, a by-product of production is the so called “magnetic sludge”. This by-product contains high amounts of neodymium, thus a process for the recovery of Nd has been proposed. In this process the Nd present is selectively chlorinated/distilled by the addition FeCl2 via the following reactions."

Jan 1, 2012

By G. Shaw

IN recent years, most of the reconnaissance work of the Geological Survey of Canada has been mapped on a scale of 1 inch to 4 miles. Topographic base maps, commonly made from aerial photographs, were available to the geologist for such work. The advent of war curtailed aerial photography for civilian purposes, and by 1941 all areas already photographed had been geologically mapped. Nevertheless, the need for geological maps to assist post-war prospecting was so apparent, and the country to be covered is so vast, that some new method of rapid mapping had to be devised. It was felt that the need would be met if geological maps could be produced at a scale of 1 inch to 8 miles, provided they were sufficiently accurate in topographic detail to serve as guides to travel. Though in such maps there would be considerable sacrifice of geological detail, they would serve to outline, at least approximately, the major geological units, some of which might prove of sufficient interest to warrant later detailed study. It seemed that such mapping would be particularly useful in the northern regions of Canada which the work of early explorers has indicated are underlain largely by granitic rocks. These, so far as is known, are barren of mineral deposits, but within them are known to be areas or bands of 'greenstones' of the type that, in some localities, have been found to contain valuable orebodies. The problem, then, was to devise a method of mapping, particularly of such greenstone bands, that would make it possible to cover a relatively large area-say 30,000 square miles-in one season and at a cost below that of 4-mile mapping, with, of course, some sacrifice of accuracy. The problem seemed to be threefold: (a) to observe as much of the bed-rock as possible; (b) to produce a topographical map of as much of the area as possible, with particular reference to portions of geological interest; and (c) to cover as large an area as possible in a limited time, which meant faster modes of travel than have hitherto been used. The obvious answer to all three phases of the problem was the use of aircraft. If rock types could be broadly differentiated from the air, reconnaissance traverses by air would supply the answer to the first part of the problem. For topography, air photographs taken on reconnaissance flights appeared to be the answer. For the third phase of the problem, the use of aircraft was ideal.

Jan 1, 1943

By Daniel Torres Espinoza, Jose Pinedo

"Ventilation is a vital service in underground mines, required to provide fresh air to the work force and dilute diesel equipment gases (CO, NOx) and diesel particulate matters (DPM). At a Mexican precious metal mine in the state of Chihuahua there is a VOD system implemented using Howden’s control and monitoring system and a state of the art tagging and tracking technology. The JM zone of the mine is ventilated using a push and pull system, using automated regulators on each level to control the air going in and out of the levels. The implementation of advanced control strategies using Howden’s VentSim™CONTROL allows the mine to generate significant savings and increase health and safety of the workers.INTRODUCTIONIn underground mines, ventilation is a requirement in order to maintain the fresh air needed for personnel and equipment. Ventilation regulations dictate the amount of air required underground to carry out day to day operations by limiting the exposure that workers have to toxic gases and other pollutants. Regulations for required airflow in underground operations for diesel pollutants are generally provided on vehicle rated brake horsepower, in Mexico the requirement is 75 cfm/bhp. In underground mines, ventilation services can account to up to 75% of the mine’s energy consumption, and it is very common for fans to operate all the time because of a lack of control infrastructure for the ventilation system. By the implementation of a Ventilation On Demand (VOD) system a mine can reduce this consumption with different control strategies. The main infrastructure required to implement this system consists of remote control of ventilation infrastructure (fans and regulators), a communication network between throughout the mine with the surface and a tracking system for personnel and diesel equipment. Software is required to determine fresh air requirements based on the tracking system data and then send the control commands to the different ventilation infrastructure. In 2015, San Julian Mine acquired Howden’s VentSim™CONTROL (formally SmartEXEC) and the hardware solution to deploy a VOD system at their operation. The VOD system and Fresnillo plc’s San Julian Mine in Chihuahua, Mexico, consists of control of 10 surface exhaust fans, 2 surface intake fans, and 12 underground automated regulators. It also includes the monitoring of 46 flow sensors, 28 CO sensors, 28 NO?? sensors and 42 temperature and humidity sensors, approximately 500 personnel tags, approximately 220 vehicle tracking tags with diesel status (ON or OFF) and approximately 250 tracking zones. This paper discusses the control strategies that have been implemented at San Julian Mine since the system was commissioned and the next steps that will be taken at the mine with the system as they test different level on VOD."

Jan 1, 2019

By D. F. Hambley

"In designing are passes f or underground mines specific consideration should be given to unimpaired flow of broken rock, the dump point, and typical practices f or overcoming operational difficulties. Design features such as branches, bends, and knuckles should also be considered. This paper pro vides engineering information and various criteria for designing are passes, draw points. feeders, and support systems, together with several illustrative examples.IntroductionOre passes are the primary mean s o f vertical transfer of mined ore to the ore bins and loading pocket from which the o re is hoisted to the surface (Fig. 1) . While the words "" ore"" and ""ore pass"" are used here, such transfer systems ca n be used for any broken rock.The most extensive ore pass systems are found in caving and sublevel stoping mines. Extensive ore pass systems are also found in multilevel mines having steeply dipping orebodies. In more flat-lying orebodies , ore pass systems are sometimes used in conjunction with conveyor systems .Two decades have passed since the principles of the flow of bulk solids were formulated (Jenike, 1961, 1964; Johanson and Colijn, 1964; Kvapil , 1965). However, few published papers are available that discuss the design criteria for ore pass systems. Therefore, the aim of this paper is to provide the information necessary for good o re pass design .Rock Flow in Ore Pass SystemsIf an ore pass system is to fulfill its function, the transfer o f material must occur in an orderly fashion and in such a way that the full size of the opening is employed effectively. Apart from un controlled flow at the drawpoint, or outlet , whose design will be considered later in this paper, two occurrences may impede flow in an ore pass, namely:• Hangups due to interlocking arches.• Hangups due to cohesive arches.Prevention of each of these problems will be discussed in succeeding sections of this paper. A third problem piping, is related to the ratio of the drawpoint size to the o re pass size and will be discussed under drawpoint de sign."

Jan 1, 1987

By W. J. Wolfe

"THE DETECTION OF BURIED MINERAL DEPOSITS by chemical analysis of vegetation (biogeochemistry) or visual observation of plant cover type (geobotany) is based on fundamentally simple principles. The root systems of vegetation collect aqueous solutions from a large volume of moist ground below surface and act as efficient sampling mechanisms by providing a composite sample of a reasonably large area. These aqueous solutions constitute a source of ore-associated metals that may ultimately be concentrated in the upper parts of the plant. Although certain plant species have a limited ability to break down primary minerals and extract elements, biogeochemistry normally detects only metals capable of moving in solution. Metal concentrations in the underlying soil must therefore exist in a form that is immediately available for uptake by the root systems - generally in the ionic state in aqueous solution or in readily exchangeable form on the surfaces of soil clay minerals. As a result, biogeochemical responses are closely related to variables such as soil pH, Eh, exchange capacity and complexing agents that control metal mobility in the surface environment. In terms of cost, reliability and anomaly contrast, soil geochemistry will normally be more useful than biogeochemistry in locating buried mineralization in regions of residual overburden or thin transported cover. However, in areas where the root systems penetrate thick deposits of transported post-mineralization overburden, plants can provide an effective mechanism of sampling below the transported material. Biogeochemical research in Canada, Scandinavia and the U.S.S.R. has therefore focused on the potential use of plant prospecting methods (1) in areas where the upper horizons of podzolic soils do not provide an adequate response to anomalous conditions under thick deposits of glacially transported till and (2) in widespread regions of peat and muskeg terrain where near-surface mineral soils are absent."

Jan 1, 1971

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By Peter A. Amelunxen, Richard LaDouceur, Courtney A. Young

"Many of the rare earth elements, the lanthanide series on the periodic table, are on the U.S. Department of Defense Strategic and Critical Materials list. In this regard, the U.S. Army Research Laboratory (ARL) has funded several projects at Montana Tech focusing on rare earth element recovery from natural resources. Current froth flotation operations utilize octyl hydroxamate for rare earth mineral extraction, however recovery is not ideal and flotation performance can be improved. Salicylhydroxamic acid (C7H7NO3) was identified as a novel collector due to similarities with n-octyl hydroxamate, notably the amine head group. Salicylhydroxamic acid is primarily used in the medical industry but due to the amine head group is ideally suited as a collector for rare earth mineral flotation.Parametric studies were performed for the flotation of rare earth minerals by modifying a wide range of variables. Mechanical variables of a 6L bench scale flotation cell, such as air inlet flow, rotor speed, and milling time for liberation were modified to elucidate energy input parameters for the desired minerals. Chemical parameters such as collector concentration and pH were varied to understand solution chemistry considerations of the salicylhydroxamic-rare earth mineral system. The study obtained a statistically significant experimental model for the flotation of rare earth minerals. A two stage compartmental model was also utilized for the determination of the first order flotation rate constants for each mineral. Optimized recovery of rare earth minerals was found to occur at near neutral pH ranges using salicylhydroxamic acid with maximum recoveries approaching ideal industrial standards although rare earth mineral grades were still not sufficient.INTRODUCTIONRare earth elements (REEs) are found in minerals that contain several REE which makes costeffective separation of the rare earths difficult. Significant scientific challenges have hindered mineral separation. The molecular similarity of rare earth elements results in minerals containing several REEs, such as bastnaesite [(Ce, La) CO3F]. This prevents efficient separation during concentration steps, for instance flotation, and has a direct impact on successive metallurgical processes. Consequently, concentration during flotation is of rare earth minerals (REM) as opposed to REE."

Jan 1, 2016

By K. Heid

"Although concentrated efforts have been made to deplete PCB transformers from the Canadian environment, numerous transformers (as well as ballasts, capacitors and magnets) continue to exist throughout the Canadian mining industry. The existing installed base is slowly being phased out as environmental issues come under increasingly high profile. The following article identifies the potential problems of owning PCB transformers and offers some solutions for their removal, disposal and replacement. IntroductionPolychlorinated Biphenyls (PCB) are synthetic chemical compounds consisting of chlorine, carbon and hydrogen. PCB was widely used in transformers due to its physical properties, including stability, low flammability and non-conductivity. Use of PCB in electrical equipment has been banned since 1977 when the extent of environmental contamination was discovered.Although PCB’s have been outlawed for use in electrical equipment since the late 1970s, safe storage regulations were not addressed until 1988 when a major spill prompted the federal government eventually to issue the storage of PCB Material Regulations in 1992. These regulations replaced the Interim order of 1988 under the Canadian Environmental Protection Act.PCB transformers are usually referred to as askarel filled transformers or as PCB contaminated mineral oil transformers. Askeral transformers were designed to contain high concentration PCB fluids, referred to as askarel. Mineral oil transformers were not designed to have PCB concentrations but were inadvertently contaminated during manufacture or maintenance activities."

Jan 1, 1998

By S. Boisvert

Risk-based Inspection (RBI) addresses the challenges associated with ageing plants by focusing the inspection effort on the process equipments with the highest risk, thereby improving plant safety and reducing inspection costs. The RBI methodology is commonly used in the oil industry through the API 581 standard. Since no such standard exists in the mining and metals industry, BPR-Bechtel has developed one using inspection data from process equipments in CEZinc. Models were developed for various damage mechanisms, such as uniform corrosion and stress corrosion cracking. The equations were organized into a user friendly software that facilitates the implementation process.

Jan 1, 2010

By BRIAN HITCHON

Calcium, magnesium, bromide and iodide extraction from formation waters for use as industrial minerals has occurred in several countries, but not yet in Canada. Potential commercial brine fields exist in th e Upper Devonian Beaverhill Lake Formation of so uthern Alberta, and the Middle Devonian Elk Point Subgroup of north-central Alberta, f rom which calcium, magnesium and bromide are potential products. Iodide contents in fo rmation waters f rom the Upper Cretaceous Belly River Formation and the Lower Cretaceous Viking and Bow Island fo rmations in central and southern Alberta are at the lower range limit of commercial iodide-bearing formation waters elsewhere in the world. Available information is insufficient 10 outline potentially commercial areas in Alberta, but such info rmation can be most easily obtained f rom test borings for shallow natural gas. Lithium is not now produced commercially f rom formation waters but its content should be monitored in view of f uture increased demand for this metal.

Jan 1, 1984

By Roderick C. McDonald

Great Bear lake, the fourth largest body of water on this continent, comprises an area of approximately 12,000 square miles, and is set astride the Arctic circle, with a large portion of it witnessing both the Arctic winter night, and the Arctic summer day with its midnight sun. The very name itself, Great Bear, suggests an Arctic region. The seasonal contrasts at Great Bear lake are very marked by the cold and darkness of winter, and the warmth and brightness of summer. Signs of winter such as low clouds, snow, sleet, fog, and night frosts, generally appear the latter part of August, while ice forming on bays during the last two weeks in September ends boat travel on the lake about September 30th.Early in June the ice leaves the river mouths, during the last ten days of the month it disappears from small bays, and at some time during the last two weeks of July the main body of the lake becomes navigable. In 1916, the ice disappeared earlier than usual, and the lake was navigable on July 5th. Great Bear river generally breaks up about June 1st, but, on account of ice cliffs and floes, it is not navigable with safety until early in July. Even then, the traveller is confronted with the Charles rapids, but these might be overcome by a wagon or motor road, such as the one from Fitzgerald to Fort Smith: However, in 1931, Mr. A. W. Boland, Fort Norman, N.W.T., carried with scow and motorboat practically all freight between Fort Norman and LaBine point and Hunter bay, at the east end of the lake. During July and August, two types of clothing are required, for, although the days are mainly ones of warm sunshine, the nights are cloudy and cold. In the winter season, fur clothing is used exclusively. Considerable timber, mainly white spruce, suitable for fuel and building purposes, borders the lake and extends eastward to the Coppermine river. North of the lake, no timber is found except in the river valleys, but with oil and coal possibilities near Fort Norman, the fuel situation might be solved.

Jan 1, 1932

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By A. Sutherland Brown, Stuart S. Holfand

"The Northeastern part of the Cariboo district lies in the big bend of the Fraser River between Quesnel and McBride. The area shown on Figure 1 extends from just west of Wells to Isaac Lake, about 30 miles across the regional strike of beds.Topographically the area extends from the moderately well dissected Interior Plateau in the west through a transition zone to the fully dissected Cariboo Mountains in the east.The area is an important source of lode and placer gold. The Cariboo Gold Quartz and Island Mountain lode-gold mines have produced more than 32 million dollars in bullion since 1932. Placer-mining has probably produced an equivalent or greater amount, although only 15 million dollars is officially recorded because accurate statistics. were not kept until fourteen years after the origiiaal gold rush of 1860.The regional structure of the Barkerville district was summarized by Lang in the Jubilee Volume (1948, pp. 141-149). Since then a large amount of detailed and areal mapping by the writers has expanded the information available and made necessary a complete revision of the regional geology. Much of the information summarized in this paper, together with a full discussion of the revisions, may be found in British Columbia Department of Mines Bulletins, Nos. 34 and 38, but other information is as yet un-published.Rocks of the Kaza group are exposed in the core of the Lanezi anti-clinorium between Spectacle and Isaac Lakes. The main part of the group is composed of greenish micaceous greywacke and greenish schist with knots of garnet, biotite, or both, and minor amounts of pebble conglomerate. The upper 1,000 feet is composed of white to brown quartzites and brown phyllites. Altogether, about 6,000 feet of the group is exposed. 1t is of latest Precambrian, i. e. Windermere, age."

Jan 1, 1949

By D. R. Keck

"SINCE the .Canadian Chemical Company has no direct connection with mining operations, and I have had no experience with mining, there is little I can tell you that you do not already know. However, we have had considerable experience with certain types of metallurgical problems and I would like to discuss with you some of these problems and their solutions by our metallurgists.In order to acquaint you with the type of plant and processes to be employed at Edmonton, I would like first to take a few .minutes to trace briefly the history -of the Canadian Chemical Company's affiliate, The Celanese Corporation of America. In the early •part of the twentieth century, two young Swiss brothers, Camille and Henri Dreyfus, received their P.h.D. degrees in chemistry. They were extremely interested in work which was being carried on at that time to find a suitable synthetic fiber that could compete with natural fibers, both quality and price-wise. Early man-made fibers were both coarse and hard to dye. The Doctors Dreyfus• poured all their earnings into research and ultimately developed cellulose acetate filament. During World War I, the Dreyfus brothers were invited to the United States to produce cellulose acetate 'dope' for airplane wing coverings. Dr. Camille Dreyfus built the first American plant for fiber production at Cumberland, Maryland, in 1924.Due to resistance of textile mills to the new fibers, Celanese was forced to set up its own dying, weaving, and finishing mills to prove the new materials. Through the years, however, this operation has •been retained primarily for fabric development purposes,.. with the majority of the acetate being sold to other textile mills."

Jan 1, 1953

By Harold N. Miller

Lost time and services caused by electrical equipment breakdown or cable faults can often be substantially reduced by the use of direct-current high-voltage testing as a maintenance tool. This paper discusses the relative merits of alternating-current versus direct-current testing, pointing out the advantages in size and cost of equipment and more definitive results achieved through the use of D.C. General principles of direct-current high-volt-age testing, types of testing, methods of performing the actual test and interpreting the results are explained. ?The value of insulation resistance measurements and their relationship to high-voltage testing is discussed. Pinpointing the physical location of a cable defect using a fault locator or thumper is described. Reference is made to several organizations that have effected considerable savings with high-voltage test programs. Introduction T HE past decades have seen great advances in the field of electrical power distribution and application. Motor generators, power-operated equipment, cables, etc., have all gone through various stages of improvement both in efficiency and reliability. Un-fortunately, however, power failures and equipment breakdown still occur -frequently with disastrous effects in loss of time,

Jan 1, 1965

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust&apos; or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013