Search Documents

By S. M. Chentouf, M. Jahazi, N. Bombardier, T. Belhadj

The main limiting factor in the commercial expansion of superplastic forming (SPF) of thin sheet aluminum alloys is the extent of cavitation phenomenon that takes place during the processing. The severity of the cavitation process is mainly dependent on the uniformity of deformation (i.e. level of local thinning) during processing. In the present paper, correlations are made between thickness variations in several formed sheets and the characteristics of the cavities observed in the material. The 1.4 mm thick 5083 aluminum alloy sheets were hot pre-formed at around 450°C for 4 min and then air-cooled. Opto-digital and Scanning Electron Microscopy were used to examine the microstructure and analyse the cavities. Also, grain size measurements were carried out for different location in the SPF formed piece. The surface and volume fractions of the cavities were measured with the aid of metallography image processing (MIPTM) on as-polished samples prior to etching. The results are analyzed in terms of the influence of applied strain and microstructure conditions on the propensity to cavitation of the alloy.

Jan 1, 2015

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

The bath level measurement is applied in many furnaces to keep control of the level of slag and metal or matte inside. The BLM is used mainly in bath processes, and has not seen much evolution in its basic functionality. For a closed DC FeCr furnace, special demands based on the furnace design and extreme process conditions were considered for the design of a bath level measurement in order to collect valuable information about the furnace operation. This paper will describe these demands and the solutions for them, followed by some of the uses for the BLM in a closed FeCr furnace. Some of the future developments on the BLM conclude this presentation.

Jan 1, 2015

By Unknown

Diesel locomotives for underground haulage have been used in coal mines in Continental Europe for twenty-five years or more. In Great Britain, it was not until 1935 that permission was granted to use them in gassy coal mines, but since that time they have been employed in increasing numbers both in gassy and non-gassy coal mines and in metal mines. Their use underground in coal mines in the United States is still prohibited and the same was the case in Canada until 1946, when permission was granted to operate a Diesel underground in the Adanac mine of West Canadian Collieries, Limited, at Bellevue, Alberta. The locomotive used here is a 50 h.p. Hunslet Mark II. More recently, a 100 h.p. Diesel was placed in operation for underground haulage at No. 18 Colliery of the Dominion Steel and Coal Corporation, in the Sydney coalfield, N. S. Thus, on this continent, Canada has been a pioneer in the use of these locomotives underground in coal mines and there is no doubt that more and more of them will be employed as time goes on. We feel, therefore, that the following notes concerning their design and performance, which we have received from the High Commissioner for the United Kingdom, will be of interest to our members.

Jan 1, 1949

By J. G. Trowell, D. T. Magee

"IntroductionMANITOBA'S first recoverable oil was from the California Standard Daly 15-18 well in Lsd. 15, Sec. 18, Twp. 10, Range 27, W.P.M., completed early in 1951. This well also gave the first indications of commercial production in the Williston basin, which is centred in North Dakota and extends into southeastern Saskatchewan and southwestern Manitoba. Subsequent drilling in the Manitoba portion of the basin has revealed the presence of oil in more or less commercial quantities at various points in an area approximately four townships in width and eleven townships in length.Although completions are becoming fairlly widespread in the area,, the greatest activity is in the Virden district, with the focal point in the Daly field, approximately eight miles west •of Virden. This paper will deal with the various techniques used in the Daly field, where •completion problems have •been unusually troublesome. Techniques evolved there have already been used with success at other points in southwestern Manitoba.Daly FieldGeneralTo date, all production has been from the Mississippian limestone, which is encountered •at depths ranging from 2,300 to 2,500 feet. Pay thickness is •of the order of 100 feet. Core analyses indicate average porosity .of about 9 per cent but permeabilities, for the most part, are extremely low."

Jan 1, 1953

By L W. Morley

The Division is concerned with physical methods as applied to geo-logical research and mapping. An at-tempt is made to describe long-term goals, illustrated by examples of projects in the fields of aeromagnetic interpretation, palaeomagnetic re-search, Pleistocene and groundwater geophysics, seismic surveying, electromagnetic research and instrument development. Cooperative projects in surveys and research, with universities, private companies and provincial organizations, are frequently undertaken. An outstanding example of this is the recently approved Federal-Provincial Aeromagnetic Survey Plan, the purpose of which is discussed both from an economic and a scientific point of view. HISTORY OF THE DIVISION M AGNETIC, electrical, seismic and gravity methods, as a means of extending the geologist's sphere of observation beyond the head of his hammer, came into wide-spread use for the first time after World ?war I. Interest in these methods was aroused amongst geologists of the Geological Survey and, in 1928, a group of these geologists and university

Jan 1, 1963

By Jeff Smith

Agenda About NORTHPARKES The NEED The INITIATIVE The SEARCH The PRODUCTS The SOLUTION The RESULTS The Northparkes copper-gold mine in Central Western NSW commenced operations in 1994. Copper concentrate is produced and shipped to smelters in Japan, China & India under long term contracts with spot sales to other Asian countries.

May 1, 2006

By J. G. Debanne

MOST company-employed petroleum engineers have in their accounting departments punch-card computers that can perform engineering calculations thirty to three hundred times faster than desk calculators, or they can rent such machines from Computing Service centres. These machines not only eliminate the drudgery of desk calculation but also the risks of human errors. The I.B.M. t 604 punch-card computer of Texaco's accounting department in Calgary has been used for oil and gas property evaluations, curve fitting by least squares, statistical core analysis studies, unsteady-state water in-flux studies, phase equilibrium performance prediction of oil reservoirs, gravity segregation calculations, etc.

Jan 1, 1958

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By Nessetech Consulting, L. A. Cisternas, E. D. Galvez, S. H. Kuan, L. H. Saw

"In Malaysia, there were two rare earths processing plants namely Asian Rare Earth (ARE) and the Malaysian Rare Earth Corporation Plant (MAREC) in Perak, which were operated until 1992 and were subsequently closed due to problems pertaining to disposal of large amount of radioactive waste. Recently, Lynas Advanced Materials Plant (LAMP) has become one of the largest rare earths processing plant in the world producing rare earth elements (REE) in Gebeng, Pahang. The primary raw material is lanthanide concentrate (LC) which is imported from Mount Weld mine in Australia and shipped to Malaysia. LC is produced from lanthanide ore after mining and mineral processing. The ore has a lower impact than Bayan Obo, Mountain Pass and adsorbed clay deposits, given the small footprint of the mine itself and the remoteness of the location. The type of ore being mined (rare earth phosphates: carbonatite, monazite) may have higher thorium content than bastnasite ore from the Chinese or American mines but still far below radiation concerns. This paper was written to review the processing flowsheet at the Lynas Advanced Materials Plant (LAMP), the environmental impact associated with the processing of the said ores and the sustainability of the operation.INTRODUCTIONRare earth minerals are one of a set of 17 minerals or chemical elements which consists of yttrium and scandium, as well as the 15 lanthanide elements (lanthanum, cerium, praseodymium, neodymium, promethium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium). Despite their importance, rare earth minerals rarely exist in economically viable concentrations and they are usually difficult to extract. Rare-earth minerals create strong magnets when added to magnetic elements such as iron, and are useful for the production of electronics systems as well as electric cars. They are also used extensively in automotive catalytic converters, fluid cracking catalysts in petroleum refining, wind turbines, phosphors in colour televisions and flat panel screens, displays for mobile phones and laptops, rechargeable batteries, and various medical devices. The elements are typically split into two subgroups: the cerium sub-group of ‘‘Light’’ rare earth elements (LREEs) which includes La to Eu and the yttrium sub-group of ‘‘Heavy’’ rare earth elements (HREEs) which include the remaining lanthanide elements, Gd to Lu, including yttrium (Gupta and Krishnamurthy, 1992; Jordens et al., 2013; Trifonov, 1963). Scandium, however, when it is classified as a rare earth element, is not included in either the LREE or HREE classifications (Gupta and Krishnamurthy, 1992; Jordens et al, 2013). Half of the world’s 110 million tons of reserves exist in China while other sizable deposits are found in Russia, United States, Brazil, India, Australia, Canada, and Greenland. The countries known to be actively mining REE are China, Russia, India, Brazil and Malaysia (Hao et al., 2015). Among these countries, China has the largest REE production, accounting for more than 93% of global supply (Yap, 2015). The critical metal report (Moss et al. 2011) listed 14 economically vital raw materials that are prone to supply disruption and concluded that supply disruption would threaten the goal for cleaner transport and sustainable energy since rare earth metals are used in products using green technology, such as hybrid/electric vehicles, carbon capture systems, wind power generation, low-energy lighting, and energy efficient flat-screen displays."

Jan 1, 2016

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015