Search Documents

By M. Hozayen, Q. Ni, E. S. Radwan, P. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests used in this study are summarized in Part I of this paper whereas wellbore stability analysis and formulation of a3D geomechanical model that was built for that purpose is summarized herein.A 3D geomechanical reservoir model was developed, which included natural fractures. The mechanical properties of the reservoir rock, such as Young’s modulus, Poisson’s ratio, UCS, friction angle and tensile strength were populated based on the correlations established in Part I of this paper and the developed model was then used to simulate the 3D mechanical-property distribution and the evolution of the in situ stresses in the field due to depletion from 1983 to present-day. Based on the full field model, mud weight cubes were developed to predict the safe mud weight windows in different drilling directions. In addition, well stability prediction for two planned wells was performed using a 3D near-borehole model. Firstly, the computed stress state and mechanical properties simulated in the full field model were extracted along the well trajectory of an existing horizontal well which was drilled recently and then, a3D near-borehole model was constructed along the well trajectory. The wellbore stability analysis along the well trajectory, including stress state, strain distribution and displacements, was performed to identify the instability events along the well trajectory. It has been seen that the presence of natural fractures is closely related to the recorded borehole instability incidents. The computed plastic strains which indicate the wellbore failure were consistent with the recorded wellbore instability events in the FMI image logs, what provide further verification of the developed model. Then, this 3D near-borehole model was applied to two planned horizontal wells and the wellbore stability analysis for the two wells was carried out.The results showed that drilling vertically in the reservoir is safer than drilling horizontally. However, the drilling mud weight window in the vertical direction is narrow, being as narrow as 18.7 pcf or 0.299 sg locally. Drilling horizontally is less stable towards the maximum far field stress direction than towards the minimum far field stress direction. The mud weight cubes were used to identify the optimal well placement and well trajectory. For planned well trajectories, this technology can also be used to determine the optimal mud weight."

Jan 1, 2015

By A. M. Reyes

Flow field hydrodynamics of serpentine flow channels was investigated numerically using computational fluid dynamics (CFD). The velocity profile simulated by the CFD model was evaluated with respect to experimental results from the literature. Rectangular and tapered flow channels were compared with respect to mixing and water management capabilities, and pressure drop. The CFD model was further developed to account for electrochemical reaction on the cathode side to determine which channel configuration was most effective in reactant conversion. The velocity profile differences between the channels were found to impact reactant conversion, as the rectangular channel had the highest conversion. With respect to water management, although the tapered channel was found to have a higher overall pressure drop, the rectangular channel was found to have higher shear and pressure forces acting on simulated liquid water droplets in the channel.

Jan 1, 2005

By Gonzalo Mato, Colin Godwin, G. Ditson

"The mid-Cretaceous Seagull batholith intruded Mississippian sedimentary and volcanic rocks and Jurassic(?) granitic and ultramafic rocks within the Omineca Crystalline Belt in the Yuk on Territory near the British Columbia boundary. Leucoerotic fluorine- and boron-rich granites of the batholith exhibit many textural variations from aplite to pegmatite, but are dominated by a coarse-grained seriate unit and a fine-grained porphyritic unit.Four distinctive tin vein occurrences within and near the batholith are described, the most interesting of which is the MC showing of quartz-calcite-chlorite-cassiterite veins in intensely fractured zones of sedimentary and volcanic rocks. Three other showings occur within the batholith:J) the EC showing of quartz-fluorite-cassiterite-sulphide veins with prominent muscovite-illite alteration;2) the DU showing of quartz-hematite-fluorite-sulphide- sulphide-cassiterite with considerable manganese staining and sericitic alteration; and3) the VAL showing of quartz-tourmaline-cassiterite-fluorite-arsenopyrite veins with little associated alteration.Most cassiterite occurrences are within easterly-trending, vertical structures and all occurrences are thought to represent parts of a single system. These mineralogical and physical variations are apparently related to the distance from the upper contact of the batholith.For the Seagull batholith, Rb-Sr isotopic data give a 100±1.4 Ma isochron age that is concordant with the K-Ar model age from biotite of 101±4 Ma. Initial Sr isotopic ratios for the batholith are high at 0.712, indicating an old, sialic crustal source for this pluton. This initial ratio is similar to values for granitic rocks associated with tungsten deposits in the Yukon Territory. The high initial ratio for Sr, the high Si02 content, the high s/I index, the presence of normative corundum. leucogranitic composition and associated lithophile-tungsten mineralization demonstrate that the Seagull batholith is probably an S-type granitic body. This factor is significant to regional exploration jar tin and tungsten in the Canadian Cordillera."

Jan 1, 1983

By G. Chi

Outline 1.Regional geologic setting 2.Host rocks and structures 3.Mineralization, alteration and paragenesis 4.Geochronology 5.Major and trace elements 6.Fluid inclusions 7.Carbon and oxygen isotopes 8.Conclusions

Apr 1, 2005

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By Tom Shumka

Introduction ?This technique detects 100% of all gear tooth surface indications, providing comprehensive data, and has the ability to size indications accurately. ?The remarkable advantages of ECA technology, is improved inspection capabilities and significant time-savings. ?The advantage of using EMCD is its ability to size indications accurately. ?This technique does not require the gear teeth to be wiped down by hand after cleaning as in MT, LT or UT inspections. (Figure 1) ?This technique will inspect one gear tooth in 30 seconds. ?All of the data can be archived for future comparisons in an electronic report. Methodology ?This technique utilizes Eddy Current Array (ECA) as the principle inspection technique. ?What has been added are specialty scanner probes with multiple coils, a multiplexer and a software package. ?With 2 and 3D dimensional isometric displays, the defect can be seen electronically as it is on the gear tooth surface, thus, reducing the reliance on human interpretation.

May 1, 2011

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By C. A. Born

This paper describes the rejuvenation of a molybdenum mine mill complex at the head of Alice Arm, 500 miles north of Vancouver and 85 miles north of Prince Rupert, British Columbia. It includes a description of the property history of the deposits and of the previous operations, together with details of the project for re-opening the mine.

Jan 1, 1979

By C. Bourgoin

"The factors constraining productivity in the mining of narrow vein ore deposits are numerous and often interdependent. This paper concerns mining techniques capable of reducing some of these constraints in the case of vein deposits whose dip is less than 45 degrees. Modifications of conventional mining methods as well as suggested new developments are presented, as are matters pertaining to the mechanization of operations as a mean of increasing both productivity and work safety. IntroductionThe mining of vein deposits, whose width (thickness) is generally less than 2 metres and whose dip is often variable, calls for the use of varying stoping procedures as well as appropriate infrastructure and equipment. In the case of intermediate dips (15 degrees to 45 degrees), it is generally conceded that the degree of mechanization is limited and that ore removal via gravity is impossible. This paper proposes certain innovations in matters of equipment use and stoping methods, together with certain technical data pertaining to the application of these new procedures Stoping MethodsTo mine vein deposits, one must choose a method that can adapt to irregular ore limits and allow, as well, for good ore recovery with as little dilution as possible. In addition, it is important to minimize development work in waste rock. In principle, one selects a method that is both safe and profitable; this method will be defined mainly by the nature of the vein deposit and its dip, by the competency of the rock formations and by certain technical considerations. Moreover, the stoping procedure in a given deposit may well change with time as a function of new layouts or new equipment."

Jan 1, 1994

By A. Dave Mackintosh

The Current demand for potash has pushed world prices to record levels and allowed Saskatchewan producers to operate at maximum capacity. Several years of strong demand has resulted in a permitting rush not seen since the 1960?s. Even though Saskatchewan has a huge potash resource, mining and processing constraints will limit the areas of economic development. Introduction In 1969 M. E. Holter prepared a report ?The Middle Devonian Prairie Evaporite of Saskatchewan?, published by the then Dept. of Mineral Resources. Holter?s report has remained the bible of geologists working in potash ever since. It is astounding that a report written before there was really much potash mining history in the province, is as valid today as when it was first published. This paper re-iterates much of Holter?s report and adds a little mining experience to essentially confirm the importance of his work.

May 1, 2008

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By Gil Espejo, Denise Duncan

"In Alberta, several initiatives are under way to form partnerships between educators and industry to work together in preparing a skilled and technically competent workforce for the future. One successful initiative is the Teachers in Business program which provides high school teachers one month paid internships in Alberta businesses. Initiated by the Science Alberta Foundation in 1992, this program has offered participating teachers a variety of work experiences and job shadowing tours in industry.A Growing Need of Education and Industry PartnershipsIn our ever evolving world, industry is in a tight race to keep up to date with new technology and to remain competitive. Industry is relying on the education system to provide them with the core base for their future workforce. To accomplish this, the education system needs the support of industry to develop the right focus to prepare its students for the race. What skills will our future workforce need? How can we best prepare our students for these needs?Teaching the latest in technology, especially at the high school level, is a major challenge. It is difficult for educators to keep abreast of the rapid changes in technology. High school graduates need exposure to the latest advancements. And so do their teachers. Students must be prepared to adapt to the challenges of the future, Le. global competition, rapid technological change and an expanding knowledge base."

Jan 1, 1995

By A. L. Irwin

THE disposal of tailing or waste material, which is generally a very large proportion of the ore treated, is a major problem in the location and operation of any concentrating enterprise and especially so where the life of the operation is expected to continue for many years. Many factors need to be taken into consideration in the selection of a tailing site, chief among which are economical handling of the material, subsequent re-treatment of the tailing, and precaution against stream pollution by waste water. The final location of many mill sites bas been governed largely by the selection of a sui table area for tailing storage. The Sullivan concentrator of the Consolidated Mining and Smelting Company is situated about three miles from the Sullivan mine at Kimberley, B.C., and one of the deciding factors in its location at this distance from the mine was the availability of a suitable area in which tailing could be deposited. In view of the indicated long life of the property, a far-sighted policy bad to be adopted in the matter of tailing storage, for not only would it be necessary to accumulate a huge tonnage of finely ground material, but also reclamation for iron recovery at some future date bad to be considered. Some idea of the extent of the problem may be grasped when it is noted that, by the end of 1938, over 18,000,000 tons of tailing bad been impounded in an area of some 200 acres.

Jan 1, 1939

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

By Franz Simon

Conventional fine gold electrolytes for barrel applications working electrolytically actually permit significant precious metal savings by corresponding optimizations but the most gold is still deposited on areas of the components where it is not absolutely essential for the desired bonding and soldering applications, i.e. in high current density areas. Therefore an electrolyte working electrolessly has been developed which inevitably leads to a much more uniform thickness distribution since in an electroless process there are no areas favoured by metal deposition and current distribution. The new electrolyte will be presented and its performance will be compared with conventional electrolytes as regards thickness distribution. The potential gold savings will be discussed.

Oct 1, 2003

By M. C. Ethier, A. L. Laramie

"The Granisle and Bell Copper mines were officially put into production in 1966 and 1972, respectively. The Granisle Mine was purchased in late 1979by Noranda and the two operations were amalgamated as one division. Both mines were closed in 1982after sustaining heavy financial losses during a period of low copper prices beginning in 1981.This paper describes the resumption of operations at the Bell Mine in 1985 after its shutdown period of three years and the dramatic and sustained improvements in productivity and efficiency realized as a result of a commitment by employees and management to the application of Participative Management and Employee Involvement principles. After a general description of the effects of such a philosophy on the operation as a whole, and a comparison to the operation's last full year as a producer, it deals with the practice of this philosophy in the maintenance department at the Bell Mine and the superb results realized.IntroductionThe Bell Copper deposit was discovered in 1963 and came onstream as a 10000 ton s per day open pit mine in the fall of 1972. Identified reserves at that time were 46 million tons of ore containing 0.50% copper. The mine shared facilities of the townsite of Granisle with the nearby Zapata-Granby mine which had established the community six years earlier.Because of easy grinding ore and improvements to milling circuits, Bell's throughput rate was increased to 17 000 tons per day by the late 1970s. In the open pit, improvements resulted in mining of additional reserves with higher stripping ratios. At startup, a half ton o f waste was mined for every ton of ore processed.By the end of 1982, with 48.2 million tons already mined, the Bell Mine had identified additional mineable reserves of 39.4 million tons containing 0.52% Cu.In November 1979 the Granisle Mine was purchased from Zapata-Granby. The two mines, with a total of 700 employees, were operated under common management as the Babine Division until 1982 when low copper price s forced the closure of both for an indefinite period.The outlook for copper prices remained bleak and only 50 people were retained on the payroll to maintain the two plants, most of them working on a part-time schedule.The population of the Village of Granisle dwindled from over 1500 inhabitants to under 500, as people moved away to seek other employment.Prior to the shutdown, the Bell Mine employed 370 people and pit extraction averaged nearly 50000 tons per day of which 16000 tons was mill feed, and the remainder waste. Total cost to produce a pound of copper was C$1.36 in 1982."

Jan 1, 1990