Search Documents

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By Alan E. Renshaw

"This paper is a practical overview of ways to reduce cost in the design and operation of an Arctic mine. The economically important issues of the Arctic mine that will be addressed include: permafrost and the active zone in general terms; road building in and over permafrost; Arctic geotechnical mine design considerations; pit dewatering techniques in sub-zero temperatures; and blasting frozen materials with techniques to obtain optimal results. A final section on a few special topics conclude this paper.Although this paper primarily refers to near surface conditions more closely associated to an Arctic surface mine, many of the ideas and techniques contained in the paper also apply to the surface construction of an Arctic underground mine."

Jan 1, 1996

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By D. Shishin

Continuous integrated experimental and thermodynamic modelling work is conducted in Pyrometallurgy Innovation Center (PYROSEARCH). The target is to develop a tool, which is capable to predict the compositions of phases, phase equilibria and enthalpy balance for pyrometallugical processes with higher accuracy. All these can be achieved by thermodynamic calculations based on Gibbs energy minimization algorithm. Recent developments made it possible to predict important factors, such as the chemical solubility of Cu in slag as a function of matte grade, temperature, P(SO2), Fe/SiO2 ratio in slag, wt% Al2O3, CaO and MgO in slag. In industrial practice, it is not only chemical solubility, but the overall amount of slag, which affects the recovery of copper and other valuable metals. It will also impact the energy balance. The presence of solids in the slag matrix influences the physical entrainment of matte in slag. Oxygen enrichment which is sometimes used to control the temperature of the furnace, may also affect the volatilization of minor elements into the gas phase. Same is true if additional fuel is used to compensate for heat balance. In other words, all key process parameters mentioned above are interrelated. Present study demonstrates the ways thermodynamic modelling can be used to link those process parameters on the example of copper smelting. INTRODUCTION Research methodology involving integrated thermodynamic modelling and experimental approach has been recently reported by the authors (Shishin, Hayes, & Jak, 2018 Shishin, Hidayat, Jak, Decterov, & Belov, 2016). Present paper reviews the updates and discusses challenges in the development of a large self- consistent thermodynamic database. The database covers the Al-Ca-Cu-Fe-Mg-O-Pb-S-Si-Zn-(Ag, As, Au, Bi, Ni, Sb, Sn) chemical system. The database works in the environment of FactSage software Bale et al., 2016 and related family of products: ChemApp (Petersen & Hack, 2007), ChemSheet and SimuSage. A list of phases, and thermodynamic models is shown in Table 1. For the copper industry, most important phases are Gas, Slag, Spinel and Liquid matte/metal/speiss. Black-colored elements represent the base system, elements in green can be considered as slag modifiers (slagging elements), and elements in red are minor. Ni is highlighted because it was included recently, in 2019, and currently under development. In addition to copper, the database covers the conditions typical for lead and zinc pyrometallurgical extraction. It is developed in consistency with the experimental results for high concentrations of Pb and Zn. Examples of applications in the present study include the thermodynamic analysis of fluxing for an agitated copper reactor to show the effect of Fe/SiO2, and calculations of copper slag cleaning using reductant.

Jan 1, 2019

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

By A. Roy MacLean

This paper outlines the changes in modern-day coal mining that have been brought about by the increased cost of labour and the use of new and highly efficient equipment. In the latter category are mentioned the ramp-plate, the Bretby cable carrier, armoured face conveyors and the shearer-loader. Greater productivity and increased safety are emphasized.

Jan 1, 1969

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By Karen Munro

Importance of Aquatic Studies for Mining ?Aquatic habitat is usually the first area where a mine interacts with the ?real world? outside the mine footprint ?Water management is a key consideration for a mine?Effects on the aquatic environment often extend to wildlife and human uses ?There is a lot of regulatory focus on issues of water quality, fish and fish habitat

May 1, 2011

By Frank Condon

?Location ?Background ?Drilling Program ?Mineral Resources ?Geology ?Economic Assessment ?Strategic Partner ?Located in Nunavik, Québec ?160 km northwest of Schefferville ?240 km south of Kuujjuaq ?160 km northeast of Brisay ?Magnetic Anomaly ?Property Boundary ?Diamond Drill Holes

May 1, 2011

By K. L. Ford, D. R. Lentz, J. H. Rickard, R. P. Taylor

Abstract - Coupled gamma-ray spectrometric and lithogeochemical studies throughout the Heath Steele Mines area, Bathurst Camp, New Brunswick, indicate that primary and secondary geochemical differences exist between the stratigraphic footwall and hangingwall crystal tuff units which host the massive sulfide deposits. Of particular interest is Th, and to a lesser extent, Zr and Y, which are more concentrated in the hangingwall than the footwall crystal tuffs, whereas the opposite is true for TiO2. This expands on earlier lithogeochemical-chemostratigraphic results concentrated in the eastern part of the Heath Steele belt that led to revision of the local stratigraphy, and necessitated a structural re-interpretation of the area with implications for exploration. Although K depletion (decreased K and K/Th) is typical of chloritized footwall zones of chloritization, these features were not fully apparent here due to the recessive nature of these altered zones. In situ radiometric analysis using a portable gamma-ray spectrometer is a rapid, inexpensive analytical technique for chemostratigraphic characterization of rock units within volcanogenic massive sulfide deposit settings, provided there is a contrast in the distribution of natural radioelements, particularly Th and K.

Jan 1, 1998

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By Michael P. Davies

Mine waste facilities, and in particular tailings impoundments, are one of the highest risk aspects of any mining venture. There are far too many recent examples of how real and/or perceived physical or environmental impact from one of these facilities has had enormous economic impact on both the specific project and the overall parent mining company. In many cases, such dramatic impacts have followed a period where a due diligence of the mine had been carried out (e.g. in an acquisition, merger or similar) or an internal or otherwise audit had taken place. Consequently, it is suggested that there is a need for an audit/due diligence framework to assist those processes in terms of assessing mine waste facilities. This paper presents a recommended framework for completing either an audit or due diligence assessment of mine waste facilities under a number of typical scenarios. The framework will be of relevance to reviews carried out prior to mine construction, during operations and for mines that have been in a care and maintenance position and are to be re-opened. Concepts of risk management are introduced as an essential part of the recommended framework. The paper should be of value to current and prospective mine owners involved in stewarding an area of significant risk to viability of their mining venture. The paper should also interest prospective lenders to these ventures.

May 1, 2007

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By Andre du Preez

Emergency Fall Arrest System Rio Tinto?s Primary Objective: ?To achieve repeatable controlled safe deceleration rates during emergency fall arrest activation (Ontario OHSA Regulations) ?Must operate effectively on mine specified steel shaft guides.

May 1, 2013

By J. G. Ross

A DESCRIPTION of the block-caving system of mining as practised at the King mine of Asbestos Corporation, Limited, Thetford Mines, Que., was presented. at the Annual Meeting of the Institute held in Quebec city, in April, 1934. The paper was published in the Transactions of the Institute for 1934. There has now been recovered, by this method, one million tons of ore, and a review of experience indicates that the method was well planned and has been executed smoothly. In approaching the problem of selecting the type of mining best adapted to this deposit, the method had to be one which would be low in cost, use no wood, and not disturb the surface immediately bounding the ore-body on two sides. Prior to 1931, block-caving had been considered but rejected, as it en-tailed disturbance of the surface area which lay within a 45° angle of the lowest contemplated workings, if the practice of such mines as Ray, Miami, Inspiration, and Morency, where this type of mining has been used extensively, was followed. At these properties there have been mined large tannages at outstanding low costs, but an extensive surface area has been disturbed in each case. In some instances, townsites in the mining area have had to be abandoned, and dwellings, not considered worth moving, have been allowed to fall into the depression. A study was made of the principles involved in the various types of block-caving, the existing information on ground movement, subsidence, etc., also being carefully analysed. Toward the end of 1931, a plan was conceived whereby the country adjoining ground being caved might be held permanently in place and undisturbed. The success of such a scheme was essential to the application of block-caving at the King mine on account of property boundaries, the Quebec Central Railway right-of-way, and expense of moving buildings. Study of existing data on caving and movement of rock, caused by sub-surface excavations of sufficient unsupported area to result in failure of the backs, indicated, in practically every instance, that such movements followed certain definite laws of mechanics.

Jan 1, 1936

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019