Search Documents

By J. T. McGrath, R C. A Thruston

The structural changes which take place in polycrystalline copper under the action of alternating cycles of torsion stress were studied, using the optical microscope and the X-ray dif-fraction camera, and an attempt was made to correlate them with changes in the shape of the cyclic stress-strain curve. It was found that the period of work-hardening was less than one per cent of the fatigue life, and that persistent surface marking, which are assumed to be incipient or actual microcracks, occur upon completion of work-hardening. X-ray diffraction patterns revealed considerable grain distortion at the completion of work-hardening in specimens cycled at a high strain amplitude. This distortion became progressively less as the strain amplitude de-creased. Mechanisms for the completion of work-hardening and the formation of microcracks are discussed.

Jan 1, 1962

By M. Desjardins

The Hoyle Pond underground mine, located in the Porcupine Gold Camp, east of the city of Timmins, Ontario, Canada, is the cornerstone of Goldcorp Canada Ltd?s Porcupine Gold Mines. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. In order to meet increased flow requirements of 256 m3/s at the mine, a new Fresh Air Raise (FAR) and new surface fans were commissioned in early 2005. The newly acquired fans were capable of supplying the desired volume of air within a range of 1.5 and 2.0 kPa. Upon commissioning of the surface fans the total pressure was found to be exceedingly high; far beyond the design capabilities of the new installation. Consequently only one surface fan could be operated at any given time providing about half the required volume of air. Extensive work was immediately started aimed at reducing the system resistance in order to permit operation of the two fans in parallel and achieve the required mine flows. Larger booster fans were installed in parallel at the 900 m level, a 3 m raise bore linking the 450 and 900 m levels was developed to twin the existing fresh air circuit, and the FAR from surface to the 450 m level was twinned with the original FAR. This strategy, completed in 2012, resulted in a drastic reduction in system resistance and pressures, allowing the two surface fresh air fans to be safely operated in parallel and meeting the flow requirements. This paper describes details of the engineering design work and commissioning of the modified ventilation system, successfully ensuring the long term viability of the project.

Aug 1, 2013

By H. Paudyal, K. Ohto, H. Kawakita, S. Alam, B. Pangeni

The orange waste after lime water modification was converted into promising adsorbents for fluoride by metal loading reaction. The effectiveness and mechanism of fluoride adsorption on metal loaded orange waste gel from synthetic and real plating solution were investigated. Amount of zirconium(IV), aluminium(III), cerium(III), lanthanum(III), titanium(IV), vanadium(IV) and tin(IV) loaded on orange waste from aquearegia dissolution were evaluated to be 1.62, 1.16, 0.93, 0.95, 1.20, 1.12, 0.97 mmol/g respectively. The maximum adsorption capacity (qmax) of zirconium(IV), cerium(III), lanthanum(III), iron(III) and aluminium(III) loaded orange waste for fluoride ions were evaluated to be 1.74, 0.91, 1.07, 0.98 and 1.01 mmol/g from aqueous solution. The mechanism of fluoride adsorption by metal loaded orange waste was inferred to be ligand exchange reaction. Application of zirconium(IV) loaded saponified orange juice residue(SOJR) for real plating solution showed effective removal of trace concentration of fluoride down to the accepted standard. The negligible interference of co existing anions like nitrate, carbonate, sulphate and chloride makes zirconium(IV) loaded SOJR a promising sorbent for waste water treatment. The adsorbed fluoride from fluoride loaded zirconium(IV)-SOJR was effectively desorbed by using alkali solution for its regeneration. This work shed light on the potential application of metal loaded SOJR to remediate fluoride contaminated water for environmental relevance.

Jan 1, 2012

By Robert A. Macinnes, Peter Moon, John P. Pappone

"This paper, in presenting the results of the application of the assessment centre method at Texasgulf Canada Ltd., illustrates a novel "" in-use"" technique for manpower training in the mining industry.IntroductionMining history is full of examples of what goes wrong when human judgment fails-disasters, floodings, loss of life and property. We must, therefore, assume the importance of selecting competent people for supervisory responsibility. This article de scribes a method for assessing supervisory ability, its first application in Canadian mining and the result s obtained over the past six years. It is known as the assessment centre method."

Jan 1, 1981

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By Dan Nower

Machinery Health Monitoring of Shovels MINExpo 2012: Caterpillar announced the largest Electric Rope Shovel, capable of 120 short tons The next day, JoyGlobal (P&H Mining) ?one-upped? CAT, introduced a shovel capable of 135 short tons Large Concern: breakdown (unplanned outages) of one machine will be more disruptive to production

May 1, 2013

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By I. M. Gordon, J. Blackshaw

"Run-of-mine ore is reduced to 4 per cent on 4 mesh (3/ 16 inch), using four stages of dry crushing. The mill feed is then reduced to 2 per cent on 48 mesh and 60 per cent through 200 mesh, using one stage of ball milling in cyanide solution. During the subsequent treatment about one-tenth of the tonnage is removed as a table concentrate and ground to 77 per cent through 325 mesh. The size of the mill tailing is 66 per cent through 200 mesh.Four stages of ore reduction began when the dry crushing plant at No. 26 Shaft came into operation at a maximum rate of 440 tons an hour on July 31, 1941. A detailed description of the crushing plant was published in C .I .M. Trans., Vol. LVI, 1953.One-stage ball milling in cyanide solution came into full operation on January 11, 1938. The ball milling plant had a capacity of 4800 tons daily when reducing mill feed at 2. 7 per cent on 1/ 4 inch to 54. 3 per cent through 200 mesh. Primary grinding to 60 per cent through 200 mesh commenced May 22, 1945, when the feed was 3 per cent on 4 mesh. Under these conditions the capacity of the ball milling plant is estimated at 4300 tons daily. A description of the 11 Hollinger Crushing and Grinding Plant"" by D. C. McLaren was published in the Canadian Mining Journal, June 1944.The concentrate grinding circuit using a 7 x 15 low discharge ball mill and a 19-foot diameter bowl classifier with a 6-inch centrifugal pump to close the circuit began operating in the ball milling plant on October 24, 1939."

Jan 1, 1965

By Raymond S. Suglo

Increasing depths of mining coupled with the mechanization of most underground mining operations have led to growing complexities in the mine environments with the production of large amounts of gaseous and particulate contaminants. Over 100,000 lives have been lost due methane gas and dust explosions in coal mine workings in both the US and Canada since 1900 when the methane concentrations exceeded stipulated levels in some workings. There is therefore the need to constantly assess and evaluate the performance of the existing mine ventilation systems to maintain safe and acceptable mine environmental conditions in workings to meet the requirements of federal, state or provincial laws. This paper uses the results of continuous monitoring of methane concentrations conducted in selected development headings in coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems in the control of methane gas concentrations in the headings. The results show that the average quantities of fresh air required to dilute, disperse and remove methane concentrations within set levels of one minute varied from 5.43 m3/s in Heading #11 (Condition 2) to 27.97 m3/s in Heading #10 (Condition 1) and this represented about 12 to 26% of the quantities required to dilute methane concentrations to safe levels within one minute under Condition 1 and 32 to 139% under Condition 2. The average dilution times in the headings studied were less than 8 minutes. The forcing efficiencies of the auxiliary systems in the headings studied ranged from poor to excellent implying that the auxiliary ventilation systems were capable of controlling the methane concentrations below statutory levels but may not be able to cope with large and unusual methane concentrations in the headings. This study is important to prevent methane gas and coal dust explosions in coal mines and thus avoid any loss of lives and property.

May 1, 2001

By O. A. Ojo, D. L. Chen, N. Zhou, J. Q. Zhang, A. K. Khan

Dual phase (DP) steels are designed to consist of hard martensite dispersed in a relatively soft ferrite matrix, which offers a favorable combination of high strength with good deformability. Fiber laser welding (FLW) is becoming increasingly important for joining advanced materials due to its flexibility and deep penetration. In this study, the microstructure of a dual phase steel, DP980, welded by FLW technique was carefully analysed. Gleeble thermo-mechanical simulation coupled with analytical transmission electron microscopy (TEM) revealed that the FLW process produced significant microstructural changes in a narrow heat affected zone (HAZ) and fusion zone (FZ), which can result in dramatic changes in mechanical properties. This is reflected in the micro-hardness profile obtained across the welded material. The salient phase transitions induced by the FLW, including the formation of new martensite grains in the upper-critical HAZ and FZ, are discussed.

Jan 1, 2014

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals.The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. It is shown here that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. However, the theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are unlikely to experience growth in crystal particle size through heterogeneous nucleation and are more likely to grow through aggregation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process."

Jan 1, 2016

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By R. L. Brown

The burning sulphide ores in the Sullivan Mine generate sulphur dioxide gases. This paper is concerned with a description of the environmental impact of SO2 on air quality in the mine and on the surface in the vicinity of the mine. As a result of surface caving, SO2 has been able to vent to surface and winds have carried it into one residential area of Kimberley. Monitoring practices are described.

Jan 1, 1977

By M. Walawalkar, C. K. Nichol, G. Azimi

Rare earth elements (REEs) are essential to the production of technologically advanced products, including wind turbines, electric and hybrid cars, automotive catalytic convertors, hand held electronic devices, and military defense systems. Their application in environmentally beneficial technologies puts them at a high priority for ameliorating environmental concerns. Because of their increasingly high demand and limiting resources, it is highly beneficial to find new sources for them. The present study is focused on leaching REEs from a phosphate based fertilizer by-product, known as phosphogypsum (PG). Global estimated world production of PG is about 240 million tonnes that is stored in the form of wet stacks adjacent to fertilizer production facilities, occupying vast amounts of land. PG also contains trace metals, which are detrimental to the environment, and hence it is crucial to monitor these stacks. We obtained our PG sample from Agrium Inc. (a fertilizer manufacturing company in Canada). We performed a comprehensive characterization of the PG sample and found that it predominantly contains Y, La, Ce, Nd, and Sm. For leaching purposes, we used hydrometallurgical acid leaching techniques. We investigated three acids over a range of operating conditions such as acid concentration, temperature, solid-to-liquid ratio, and residence time. We achieved an average leaching of 81% with hydrochloric acid as leachant using operating conditions that can be easily replicated in industrial settings. If our process is implemented, not only will it reduce the size of the existing PG stacks (mitigating their environmental risks), but also enable the development of new innovative routes for extracting REEs, making countries like Canada less vulnerable to supply disruptions.

Jan 1, 2016

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

By G. M. Ritcey, B. H. Lucas

In the conventional alkaline leaching of concentrate containing nickel, copper and cobalt, copper is usually removed from the system, prior to nickel reduction, by sulphide precipitation. A new process is described for the selective extraction of copper and separation from cobalt and nickel, using liquid-liquid extraction. General Mills LIX-63 dissolved in a kerosene diluent is the extractant. Trace amounts of co-extracted cobalt and nickel are easily removed by a scrub treatment, and copper is recovered from the extract by sulphuric acid stripping, thus providing a solution amenable to the oroduction of electrolytic copper. Estimated processing costs are included together with a proposed flowsheet.

Jan 1, 1972

By M. Grenon

"The presence, size, orientation, nature, and persistence of geological discontinuities dictate the behaviour of a rock mass. Block size, which is defined by discontinuity spacing, by the number of joint sets, and by the persistence of the discontinuities delineating potential blocks is an important indicator of the degree of fracturing of a rock mass. Consequently, block size is represented either explicitly or implicitly in all rock mass classification systems employed for analysis and design of surface and underground mining structures. Insitu block size distributions may provide a better means to describe the structural complexity of a rock mass. These are the distributions that would be derived if the in-situ rock mass was separated into its constitutive blocks, delineated by existing discontinuities, and each block measured. This paper presents the results of a field campaign at Louvicourt Mine aiming to characterize the rock mass using different methods for determining block size and block size distributions. IntroductionGeological structural data are used to provide input data for analysis and design methods for surface and underground structures. As the collection of structural data involves considerable investment of time and effort, it is sometimes overlooked, thus denying an important source of information for mine design. What is somewhat surprising, however, is that when structural data are available, they are not used to their full potential. Recent work has shown that data on block size have potential applications in different areas of rock engineering:• Blasting — Hudson (1993) has described the excavation process as the change of a preexisting natural block size distribution to the debris fragment size distribution (Fig. 1). Lizotte and Scoble (1994) have reviewed previous efforts on integrating site specific geological conditions into blast design. Grenon et al. (1997) provide a case study where in-situ block size distributions are compared to photogrammetric studies of blasted rock.• Rock mass classifications — Block size is used in the majority of rock mass classification systems either explicitly, as in the RMi classification system Palmstrøm (1995), or implicitly, such as in the NGI system, Barton et al. (1974)."

Jan 1, 1998

By J. D. Allan

"IntroductionThe purpose of this paper is to present a general picture of the Lynn Lake nickel area of northern Manitoba. The geology of the area will not be discussed in great detail, nor will the mining op; rations presently being conducted. Both subjects will be treated briefly and, in addition, mention will be made of some of the problems encountered in mapping in the area. some of the questions which still remain unanswered, methods of prospecting that have been applied and the future possibilities of the area.For present purposes, the Lynn Lake area will be considered as extending from west of Lynn lake to east of Barrington lake. Thus, more correctly, it should be termed the Lynn Lake-Barrington Lake area. It comprises five 15-minute map-areas, or a total of 800 square miles, in a block 47 miles east-west and 17 miles north-south.Lynn lake itself is about 120 miles north of Sherridon, Manitoba, the closes t rail terminal. The area is part of the Granville Lake sheet which was mapped by the Geological Survey of Canada in 1932, 1933, and 1935, the results being published in Summary Report 1933. Part C, and as Maps 343A and 344A on a scale of four miles to o.ne inch. In 1940, the McVeigh Lake area was mapped by the Geological Survey of Canada on a scale of 1,500 feet to 1 inch and a map was issued in 1945."

Jan 1, 1950