Search Documents

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By A. F. Buckham

Introduction Several basins of the Nanaimo series, a group of coal-bearing sedimentary rocks of Upper Cretaceous age, underlie parts of Vancouver island and the adjacent gulf islands. One, the Nanaimo basin, occurs on the southern half of the west shore of the gulf of Georgia. About fifty square miles at the north end of this basin are known to be underlain by productive coal seams, this area being known as the Nanaimo coal field. Coal has been mined from two horizons- that of the Wellington seam, fairly low in the series, and that of the Newcastle and Douglas seams, about the middle of the series. Coal has been mined here since the fall of 1852. About fifty million tons have been produced, almost half the total production of British Columbia. About seventy-two years ago, James Richardson of the Geological Survey made a reconnaissance of the coal measures on Vancouver island, and thirty-five years ago C. H. Clapp mapped and reported on most of the Nanaimo coal field. Twenty-four years ago, J. D. MacKenzie extended the work to those areas not mapped by Clapp. MacKenzie died before the results of his work could be published, but did issue a revised estimate of the Goal Resources of Southern Vancouver Island. Work by the present writer is a further contribution by the Geological Survey to knowledge of the island coal measures. Having spent more time in the field, and having had more data at his disposal than were available to his predecessors, the writer has been able to throw additional light on the Nanaimo, and other, coal fields on Vancouver island. He is indebted to Canadian Collieries (Dunsmuir), Limited, and to its officials for access to much valuable information in their possession.

Jan 1, 1947

By John H. Walsh

"ForewordPart I of this paper, published in the March 1992 issue of the CIM Bulletin, surveyed the probable consequences of a limitation on the emissions of carbon dioxide to the atmosphere for the steel industry. What might be termed the conventional responses to this restriction open to the industry were also surveyed in that section. This section, Part II of the paper, explores a new option - the possibility for the joint production of iron and liquid fuels useful for transportation purposes. In this case, it is shown that it is important to minimize the production of carbon dioxide during the reduction stage to maximize the proportion of the reductant carbon embodied in the fuel. It is also advantageous to conserve hydrogen in the reduction step. In essence, the same carbon fulfills two purposes: it serves as a reductant and fuel for ironmaking and then as a constituent of a liquid fuel. If recovered plastics could be used in ironmaking, the same carbon could serve three useful purposes in turn. The conditions and limitations for the joint use of carbon in such 'cascading' processes are explored below. ABSTRACTIt is becoming increasingly probable that emissions of carbon dioxide from the fossil fuels will have to be reduced to deal with the threat of global warming. This issue is likely to be resolved one way or the other in the period 1995 to 2000 which does not leave much time to develop responsive options. In the intervening period, the policy of the Government of Canada is to stabilize emissions of greenhouse gases at their 1990 level by 2000, by encouraging greater efficiency in the use of energy. Should further reductions prove necessary, economic instruments would probably be employed but these would not be applied before a comprehensive international agreement is reached.There are three main themes in this paper: it is assumed that measures to control carbon dioxide emissions will in fact be necessary by the turn of the century; that there will be a rising need for liquid fuels to supply the world's steadily growing fleet of motor vehicles for many years to come, and that the future niche for Canada's industry in such a carbon-constrained world will be the operation of the energy-intensive industries with efficiency and environmental sensitivity.The steel industry, as a large user of both coal and energy in other forms, would be significantly affected by a need to reduce carbon dioxide emissions. This paper first examines what might be called the conventional responses open to the industry in such a situation and then explores a new possibility for making better use of carbon by the co-production of iron and liquid fuels."

Jan 1, 1992

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By A. M. Christie

Acknowledgements The following account has been compiled mainly from records and maps of Eldorado Mining and Refining (1944), Limited, hereinafter called the Crown Company. This work was done under the supervision first of R. F. Murphy, Chief Geologist, and later of E. B. Gillanders, Eldorado Mine Manager and Manager of Eldorado Exploration Division. W. F. James and B. S. W. Buffam are consulting geologists. Since 1946, S. N. Kesten has supervised geological work for the Company in the Goldfields area. Where maps of Eldorado properties have been included in this paper, the name of the geologist who examined the property is acknowledged on the map. Outline of General Geology The geology of the area is described in the Goldfields and Martin Lake preliminary maps of the Geological Survey and accompanying Paper 49-17. In brief, the Tazin series of Precambrian age, consisting mainly of sediments with minor interbedded volcanics and basic intrusives, is intruded and replaced by granite, now generally gneissic. The late-Precambrian Athabaska series of conglomerate and arkose, with interbedded basalt and andesite flows, rests unconformably on the older rocks. All these rocks are cut by small diabase dykes. The geological terms used in this paper and in the accompanying figures are standard with the exception of the term 'mafic rocks'. These include all the basic or dark coloured rocks of the Tazin group, such as amphibolites, biotite schists, and chlorite-epidote rocks (greenstones), whether they be of extrusive, intrusive, or sedimentary origin.

Jan 1, 1949

By H. McIntire, R. Preston, D. Roberts

"Repeated 3D terrestrial digital photogrammetric surveys were conducted on hard rock mine pillars to characterize damage during secondary mining. Damage was quantified by measuring Depth of Failure, DOF, from spalling material and crack intensity, D21. These damage values were then correlated to visually assessed Pillar Damage Ratings and numerically estimated pillar loads. Measured damage, particularly Depth of Failure, correlated well with Pillar Damage Ratings. Numerical predicted pillar stress vs. damage exhibited the expected trend with shorter pillars being stronger. High resolution photographs and 3D models were also used to characterize damage mechanisms, which were found to be structurally constrained. INTRODUCTIONThe Doe Run companies Southeast Missouri Operations consists of six room and pillar lead mines (Brushy Creek, No. 29, Casteel, Buick, Fletcher and, Sweetwater) (The Doe Run Company, 2014). The mines are hosted in the Carbonates and Shales of the Viburnum trend with mining depths varying from 180 to 300 m. Pillars are commonly cut square with widths varying from 7 to 9 m and heights generally between 5 and 18 m, resulting in extraction ratios between 80 and 85% (Roberts et al., 1999). Figure 1 presents an idealized stratigraphic section through the Viburnum trend and Figure 2 shows a plan view of the five areas spanning the three mines included in this study."

Jan 1, 2015

By Pierre Giasson

"Les avantages de l'électricitéLe thème de la réunion 1982 de l'ICM District No. 2: "" Le défi des années 80 pour l'industrie minière de la Côte-Nord"" exprime trè s bien la réalité . En effet, la récession économique qui touche présentement tout le monde industrialisé, frappe de façon particulièrement sévère le marché du fer et de l'acier. Il est donc primordial pour les industries minières de la CôteNord de minimiser leurs coûts de production. Comme on sait, une bonne part des coûts de production est directement reliée à la consommation d'énergie.Si on retourne en arrière de quelques années, les prix des produits pétroliers étaient beaucoup moins élevé s que maintenant . Par exemple: A Philadelphie, en janvier 1930, le prix de l'huile no. 6 (bunker C) était de 1.22$ le baril. En 1940, le prix mondial du pétrole brut se situait aux environs de 1.80$ le baril et augmentait très lentement jusqu'en 1973. A la mi-octobre 1973, l'organisation des pays exportateurs de pétrole (O.P.E.P.) surprend le reste du monde en annonçant que le prix du brut grimpe à S.12$ le baril. .. on connaît la suite.On sait qu'au point de vue énergétique, le nord du Québec est l'une des régions les plus avantagées au monde. Malgré le fait que notre climat soit plutôt défavorable, nous sommes assurés d'une alimentation électrique à toute fin pratique éternelle, contrairement aux autres régions du globe. En effet, l' hydro-électricité ne représente que 2.S070 de toute l'électricité produite dans le monde.Une bonne partie de l'énergie consommée dans les industries minières de la Côte-Nord est utilisée pour produire la vapeur. Or, il y a plusieurs avantages à produire de la vapeur à partir de l'électricité:1. Le prix d'achat d'une chaudière électrique peut être moins de la moitié de celui d'une chaudière à carburant fo ssile.2. Le prix de l'électricité est plus bas que celu i des autres sources d'énergie disponibles dans notre région.3. Hydro-Québec offre un programme spéci al de subventions et un prix garanti de l'électricité, inférieur de 10070 à celui de tout autre combustible (1982).4. Souvent il est possible d'utiliser l'énergie hors pointe à un coût minime.S. L'espace requis pour un chaudière électrique est beaucoup moindre. Par exemple: une chaudière d'une capacité de 120000 Ibs/hre ne demande que SO pi? de plancher, c'est-à-dire un cercle de 8 pieds de diamètre comparativement à environ 600 à 700 pi2 pour une chaudière au ma zout.6. Aucun espace n'est requis pour l'entreposage du carburant.7. Aucun espace n'est requis pour la cheminée.8. Il n' y a que très peu de pièce s mécaniques, donc ces chaudières demandent très peu d 'entretien .9. Les chaudières électriques ne génèrent aucune pollution, donc on n'a pas besoin d'équipement coûteux de contrôle de la pollution.10. Ces chaudières sont extrêmement rapides. En effet, on peut passer de zéro à la production maximum en moins d'une heure si la chaudière est froide et en quelques secondes seulement si la chaudière est à sa température d'opération.11. L'efficacité de ces appareils est au moins de 9S% par rapport à 80-8S% pour les chaudières au ma zout. De plus, cette efficacité demeure la même quel que soit le niveau de production de la chaudière. Il faut faire attention ici: les manufacturiers proposent des rendements de 99% et plus, mais ceci ne tient compte que des pertes de chaleur à travers l'enveloppe, et de l'énergie nécessaire au fonctionnement de la pompe de circulation. Il faut ajouter à cela l'énergie perdue à cause de la vidange qui varie selon le type de chaudière et selon la qualité de l'eau d'alimentation.12. Ajoutons simplement que ces appareils sont très facile à opérer du fait qu'il n'y a aucun système complexe à manipuler.Cependant, il y a un inconvénient non négligeable à utiliser l'électricité comme source d'énergie: comme on ne peut pas emmagasiner l'énergie électrique, nous sommes à la merci du fournisseur."

Jan 1, 1985

By S. Dessureault

The relatively recent explosion of available data in all business sectors has induced a common expression of “drowning in data, starving for information.” The mining sector is affected by the information age through equipment-based sensors, process monitoring, and traditional enterprise data sources. Information technologists have developed techniques such as data mining that apply new and old statistical algorithms to large datasets. Mine planners and managers can apply these tools for improved planning and control, thereby increasing the use of the highly underutilized information system infrastructure in most modern mines. This paper describes the use of data mining and its enabling technology, data warehousing, in the development of an energy consumption model for large surface mines using real historical data.

Jan 1, 2007

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By F. A. McLean

The past decade has witnessed a rapid increase in the number and variety of uses found for internal combustion engines in mining operations. Gasoline engines are now widely used for operating core drills, pumps, compressors, small hoists, switching locomotives, tractors, boats, and other equipment. The heavy-oil engine is employed for operating compressors, generators, shovels, ore-milling machinery, and- in the iron, copper, and coal districts- in connection with that' latest newcomer in modern railroading, the oil-electric locomotive. Each of these applications could well form a subject for a lengthy treatise in itself. This paper, however, will be confined to a discussion of some of the features of internal combustion engines as applied to mine compressing plants and mill drive. Perhaps at no time in the history of mining in Canada has the search for new mines been more vigorously carried on, more old properties rejuvenated, or more remote districts exploited than during the past three years. The mine operator of today has a far wider range of equipment and facilities at his disposal than had the pioneers of Rossland, Cobalt, or Porcupine. Each year now witnesses the hinterland driven farther and farther back as improved forms of transportation, machinery, and methods make possible the exploration of properties once considered too inaccessible to warrant serious attention. Howey, Sherritt-Gordon, Callinan-Flin Flon, Jackson-Manion, Picard Gold Mines, and a number of properties in British Columbia, afford excellent examples of work carried out on an extensive scale miles from a railway, or in comparatively inaccessible mountain regions.

Jan 1, 1928

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By J. M. Wolverton

CONSIDERABLE interest has always been taken in Safety-First and First Aid at the Sullivan mine. Even during the early days of development, Safety-First committees periodically held meetings, while lectures in first aid were given to any employees interested in the work. In 1929, a Safety Department was organized, and all accident-prevention and first-aid work was put in charge of a full-time Safety Engineer. An extensive programme has gradually been developed, the value of which can best be indicated by the reduction of the accident rate from 18.4 shifts lost per 1,000 shifts worked for non-fatal accidents and two fatalities for 1927, to 3.24 shifts lost per 1,000 shifts worked and no fatalities for 1936. SUPERVISION All work connected with accident prevention or first aid is under the jurisdiction of a central committee, known as the Accident Prevention Committee, which meets regularly once a month. It consists of all superintendents, department heads, foremen, and shift bosses, and is presided over by the Safety Engineer. At these meetings, the accident records of the previous month are reviewed and all accidents carefully analyzed and discussed. All proposed changes in the safety rules or in the accident tprevention programme are taken up and passed upon. Complaints or suggestions from the Safety-First Committee and the Employees Co-operative Committee, dealing with safety, are discussed and passed upon or a subcommittee is appointed to investigate and take any action found advisable. The question of underground ventilation and dust control, which recently has become a very important problem, always receives considerable attention.

Jan 1, 1937

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949