Search Documents

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By Jack Parker

"The original design of mine openings and pillars at White Pine was based upon traditional assumptions; i.e., that the principal load is due to the weight of overburden, and that horizontal stresses are equal to one-. third of the vertical.Beginning January, 1964, borehole deformation measurements confirmed suspicions that the principal stress is horizontal and several times greater than the vertical.Vertical stress appears to be directly related to depth, but lateral stresses vary considerably in direction and magnitude. The direction of major principal stress lies parallel to the bedding and is apparently parallel to tension joints. Lateral stresses appear to originate from an igneous intrusive.Mining induces stresses which add to the primitive stresses, in some areas precipitating failure. In this paper, rock failures are illustrated, methods of measurement and typical results are given, and measures to counter or utilize the lateral stresses are described."

Jan 1, 1966

By I. V. Kojo

Continuous development of technologies has been self-explanatory for Outokumpu Technology's engineers for decades. The aim in the development has always been the improvement of profitability of the copper production but also the sustainability of the processing i.e. high copper recovery, low external fossil based energy utilization, high emission captures and of course low operation and investment costs. Outokumpu Technology's long-term view of the development is a change towards continuous processes and elimination of number of unit operations in smelting i.e. elimination of possible sources of emissions. Outokumpu blister smelting processes i.e. Outokumpu Direct-to-Blister Flash Smelting and Kennecott-Outokumpu Flash Converting have shown excellent operational results during the years of operation and it is expected that soon more than 10 % of the world primary copper is produced by these technologies. The paper will give some background of this development trend.

Jan 1, 2007

By B. McFadzean, J. Taguta

In order to recover minerals by flotation, the sub-processes of collector adsorption onto the valuable minerals followed by bubble-particle attachment should occur efficiently. This paper investigates both of these sub-processes for various thiol collectors and their mixtures onto base metal sulfide minerals. The aim of the work was to investigate whether there is a correlation between the strength of the collector interaction with the mineral and the subsequent bubble-particle attachment. The collector-mineral affinity was measured experimentally using an isothermal titration calorimeter in order to determine the molar enthalpy of adsorption for each collector-mineral system. The bubble-particle attachment was measured using a microflotation device which essentially determines the hydrophobicity of the mineral. Sodium ethyl xanthate (SEX) and sodium diethyl dithiocarbamate (DTC) and mixtures thereof were used as collectors with either single minerals or binary mixtures of pyrite and chalcopyrite, respectively. The adsorption enthalpies of the collectors were interpreted with reference to the chemical structure of the collector molecule and showed that the greater the positive inductive effect of the collector, which may be qualitatively related to their pKa, the greater their affinity for the mineral surface. In the microflotation studies, recoveries were strongly related to the alkyl chain length but there was no correlation between the enthalpies of adsorption and the flotation recoveries. When mixtures of collectors were used there was clear evidence of synergistic effects and in the case of DTC/xanthate mixtures it is possible that this synergism is related to a DTC promoted oxidation of xanthate to dixanthogen. When mixtures of pyrite and chalcopyrite were used the flotation recovery and enthalpy of adsorption of SEX onto the individual pyrite particles in the mixture increased substantially compared to the case of pyrite alone. Mechanisms are proposed to interpret these important observations.

Jan 1, 2016

By Graham Farquharson, Jame Marshall

"Mining towns have always been an important part of Canadian geography. Many Canadians grew up in them. The frontiers of northern Canada would be a lot closer to the United States border but for the pioneering of new mines, new towns, and new transportation routes. Names such as Labrador City, Chibougamau, Val d’Or, Rouyn-Noranda, Kirkland Lake, Timmins, Sudbury, Red Lake, Thompson, Flin Flon, Yellowknife, Whitehorse,Trail and Kimberley are some of the better known larger communities that have grown to become major commercial and government centres, but which started as the base for a mining development.Many other smaller towns never grew beyond being small communities, dependent upon the local mine and many of these are still alive, but perhaps not quite what they used to be. In this list would be Buchans, Schefferville, Chapais, Cadillac, Virginia town, Lynn Lake, Uranium City, Pine Point, and Keno Hill.Nevertheless, all these towns and dozens more like them were residential communities where people lived and raised families and were quite accustomed to being days from the major centres of Montreal, Toronto, Edmonton and Vancouver, and not just hours away as wet end to measure travelling time today."

Jan 1, 1996

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Robert B. Parsons

"Canada doesn't really have a tax system for mining - it has eleven separate tax systems! The consequent maze adds some undefinable margin of difficulty to making investment decisions in Canada. But, this 11U1Ze is not likely to be simplified. Solution: learn it and sell it! Intricate Network of Winding PathwaysWebster's New World Dictionary defines the word ""maze"" as follows: ""a confusing, intricate network of winding pathways; labyrinth ... a state of confusion or bewilderment"". Webster's does not go on to give an example of a maze, but the dictionary could easily have referred to the taxation of a Canadian mining operation. The uninitiated would almost certainly look upon such taxation as a maze of the most perplexing sort.Twenty years ago, Canada's tax system was really quite simple. It is true that Canadian mining profits were subject to three levels of taxation (federal income tax, provincial income tax, and provincial mining tax), but this didn't pose a problem. Prior to 1974, at least the provincial income tax systems were somewhat the same in terms of rules .and rates, and even the provincial mining tax systems resembled one another. Mining profits were subject to pretty much the same rules, no matter what province or territory hosted the mine. Those were the “good old days” one could even dare to generalize about tax rates without fear of being labelled an imbecile!"

Jan 1, 1994

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By Robert M. Vadas

Special considerations are described as they apply to the design of ring gears for high-power grinding mills. AGMA requirements, the importance of the supporting structure, material selection and related field experience are discussed, with special emphasis on available and developing manufacturing technologies.

Jan 1, 1978

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By J. C. Murray

Introductory: In dealing with a topic so large, one that involves such a multiplicity of details, and that also has certain controversial aspects, it is quite impracticable within the limits of this article to touch upon many most interesting phases and incidents. Also, to bring out the actual truth, it is necessary to make certain categorical statements. The writer believes that all such statements made here-under are supported by facts. Again, however, it is out of the question to cite all the proof. The writer, therefore, will gladly answer any pertinent criticisms or questions and thus supplement the unavoidable brevity of this paper. Controversial points will take care of themselves. Historical: For present purposes the history of gold mining in Nova Scotia may best be summed up in a very few paragraphs, in some of which the writer quotes freely from recent reports compiled by himself. The first material discovery of gold was made in the year 1860. As this and rapidly succeeding discoveries were looked upon as bonanzas, the claims were fixed at a size of 20 by 50 feet, and a yearly rental of $20 was charged. Later the claims (areas) were increased in size to 50 by 150 feet. In the year 1866 a temporarily successful company, so we are informed by a contemporary writer, owned a mill and mining plant worth $6,000. As this fact is cited with admiration, it is apparent that most of the mining and milling must have been done in a very primitive manner indeed.

Jan 1, 1926

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By Jeremy G. Berg, James B. Mulligan

"There is a very small fraction of wireless experts in the world with experience in underground installations and an even smaller fraction that have experience specific to building mine shafts. This is why in 2009, Redpath created its own system to meet the demands specific to shaft construction. Today, after a dozen shaft installations and several design iterations, Redpath has the expertise and experience required to implement a proper wireless system in any shaft configuration.This document will explain multiple proven wireless communication designs optimized for shaft construction and suitable for permanent use. This includes line of sight installations up to 1200m, short range mesh networks, and the latest patent pending Integrated Leaky Feeder Mesh Network. Additionally, this document will explore the lessons that Redpath learned in its effort to interconnect the people and tools needed to build a mine shaft.INTRODUCTIONAfter a decade of research, several design iterations and a dozen application examples, Redpath has resolved two wireless network architectures to best serve mine shaft construction projects.The long range line-of-sight (LOS) wireless network is the most cost effective and easiest to install, but requires an unobstructed line of sight between the working area and the shaft collar. As such, long range LOS is best suited for ventilation shafts or during the first phase of shaft sinking, before the shaft is equipped.Alternatively, a mesh network uses radios installed at pre-determined intervals in the shaft and on each conveyance. A wireless mesh uses antennas to bridge intervals between shaft radios, whereas Redpath’s integrated leaky feeder mesh network (patent pending) bridges these intervals with radiating cable, commonly referred to as a “leaky feeder” cable. Both of these mesh configurations can provide continuous reception for hoist conveyances travelling in shafts without line-of-sight, making them ideal for shaft equipping and even permanent installations in both mine shafts and lateral drifts.BACKGROUNDHoist operators receive operating commands using what are commonly referred to as “bell signals.” These instructions are delivered in a series of coded pulses on a spring returned pull cord or push button that is typically hardwired back to the hoist operator’s control room from one of many locations in the mine shaft. During the construction phase of a traditional mine shaft, a worker riding inside the sinking bucket would have to reach out to a pull cord installed on the shaft wall to send a stop command to the hoist operator. Today, Redpath’s modern shaft sinking projects use fully enclosed personnel carriers to protect the workers riding inside, specifically preventing workers from reaching out into the shaft while the hoist is in motion. The enforcement of this safety feature on all shaft projects in 2008 forced the engineering group at Redpath to find a suitable wireless solution for hoist communication to facilitate shaft construction.THE IDEAL COMMUNICATION SYSTEM FOR MINE SHAFT CONSTRUCTIONIdeally, the shaft communication system should not transform the tools to which the miners have grown accustomed. It should support the push-to-talk functionality of traditional VHF handsets and the standard belling system that has been used for decades. Additionally, it should be able to support a vendor independent framework upon which new devices and features can be added. The following paragraphs summarize some of the important requirements Redpath has identified.Support for voice transmission: Low latency is critical to prevent jitter during voice transmissions. The system must be compatible with commercially available mobile handsets and support several simultaneous conversations with the ability to broadcast a voice message to all users on a select channel using a “push-to- talk” microphone and loudspeaker.Transmission of PLC data: Low latency is required to"

Jan 1, 2019

By A. B. Baldwin

"Uranium and thorium mineralization occurs at several localities in eastern Quebec along the north shore of the Gulf of St. Lawrence. The main occurrences are near Sept-Iles, Baie Johan Beetz, Romaine and St-Augustin river. Mineralization occurs mainly as disseminated uraninite, uranothorite, uranothorianite, monazite and minor zircon and allanite. Yellow to orange oxidation products are observed along fracture planes of the uranium-bearing deposits to a depth of a few feet. Magnetite, biotite and smoky quartz have a distinct tendency to accompany the radioactive minerals. The host rocks include white to pink pegmatite, pink granite and also, in the case of the Romaine and St-Augustin River occurrences, cream to grey plagioclase-rich, well foliated paragneiss and migmatite. Radioactivity near secondary structures, such as fractures and joint planes, indicates some reconstitution of radioactive minerals.The North Shore of Quebec is the northeast extension of the Grenville sub-province. It is also a uranium-thorium metallogenic province."

Jan 1, 1970

By N. M. Steven, J. M. Moore, J. L. Kuyper

Abstract - Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, largely ensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegmatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphie order of host rock): (1) thin (5 cm to 2 meter) quartz+ plagioclase+ diopside ± scapolite cale-silicate granofels with finely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the cale-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); garnet+ pyroxene ± vesuvianite + scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unmineralized leucogranites; metaturbidite-hosted scheelite- (and possibly wolfrarnite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; scheelite-bearing vesuvianite +quartz+ garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt% W03 and 8 wt% CaF2.

Jan 1, 1994