Search Documents

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973

By J. C. Heaslip

Introduction The greatest single advance in rock drilling practice since the advent of percussion drills was the introduction of tungsten carbide tipped rock drill?bits. The evolution of rock drills has been a long and highly diversified effort which has culminated in the highly refined ?drilling machines we know today, but because of the spectacular possibilities shown by ?detachable bits, and especially those with tungsten carbide inserts, there is little doubt that the cutting face of .the drilling unit has in recent days stolen the spotlight of rock drilling research and commanded the major attention of the rock drilling fraternity. "Solid" Steels Until about twenty years ago, all rock was drilled with a one-piece rod with a bit forged on one end. In the early years of the art of rock drilling, there was tried every conceivable pattern of :bit from the single-edge chisel to elaborate geometric 'designs. In the end, it was found that a 4-point bit with two sharpened cutting edges crossing each other at right angles would serve best for most rock drilling requirements. For some years thereafter, the main concern of drill manufacturers was .to obtain the best possible steel for drill rods. This was not accomplished as easily as might be thought. The cutting end had to be such that it could be hardened sufficiently to do its work without premature dulling and yet not so brittle as to shatter under the multiple impacts.

Jan 1, 1951

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By B. J. Walsh

ABSTRACT Segregation of sphalerite minerals in zinc concentrates into christophite, marmatite and ordinary sphalerite by means of magnetic fractionation is investigated. A Frantz ferromagnetic filter, 1.2 amp., and a Dings magnet, 0.3 amp., is used to fractionate seven zinc concentrates produced in the Province of Quebec. The Dings magnetic product contains the pyrrhotite, and the sphalerite as christophite. The Frantz magnetic product contains sphalerite as marmatite, while the Frantz nonmagnetic product contains ordinary sphalerite. The results indicate that the magnetic susceptibility of sphalerite increases with increasing isomorphous iron content and that a satisfactory separation into christophite, marmaite, and ordinary sphalerite may be accomplished by magnetic fractionation. INTRODUCTION SPHALERITE, the chief ore of zinc, is almost never pure zinc sulphide. Iron is almost always present isomorphously replacing an ?equivalent amount of zinc. What may be referred to as 'ordinary' sphalerite contains up to 10 per cent iron. More highly ferriferous varieties, with 10 to 26 per cent or more iron, have been named marmatite .and christophite.

Jan 1, 1951

By P. O. Sandvik, George Erdosh

"AbstractThe Cargill phosphate deposit, located 32 kilometers southwest of Kapuskasing, Ontario, was discovered by the Resource Development Group of International Minerals & Chemical Corporation in 1975 and has been evaluated through an extensive program of 190 drill holes, numerous chemical analyses, metallurgical tests, and engineering and economic studies.The Cargill alkalic complex, comprising principally car-bonatite and pyroxenite-amphibolite rocks, was intruded in to the rift system of the Kapuskasing High during late Precambrian time about 1,800 million year s ago, near the intersection of northeast- and northwest- trending faults. The Cargill complex is one of at least ten known alkalic complexes in or close to the Kapuskasing magnetic-gravity-high system and is expressed by an elongated, northeast- oriented, three-part magnetic anomaly 7.2 kilometers long by 2.8 kilometers wide . Weathering and leaching under assumed temperate to cool, moist climatic conditions , and controlled by faulting, shearing and/or initial petrographic variations within the carbonatite , developed a small, locally confined karst system in the car bonatite rocks and resulted in a thick enriched leached carbonatite zone, capped by troughs and sinks, filled with a residuum of apatite, goethite, clay and other minerals stable in the near -surface, oxidizing environment. Overburden is 5 to 165 meters thick."

Jan 1, 1977

By Aaro E. Aho

Yukon, one of the most potentially accessible, relatively undeveloped, regions of Canada, has major mineral possibilities. The Klondike placer gold fields and the Mayo silver-lead ?district are the sole major producers but large base-metal re-serves have been discovered in re-cent years and important asbestos deposits are now being explored. Several major exploration companies are active in this region despite short seasons, permafrost overburden, remoteness, lack of transportation, and resultant high costs. Pro-posed new roads can be expected to accelerate development. At ?present the major future mineral possibilities are considered to be lead-zinc, copper, aslbestos, silver-lead, gold, and mineral fuels. These and other mineral possibilities are outlined for various geological subdivisions of Yukon. Major favourable metallogenic features of Yukon include complexity of rock types and structures, widening of the Cordillera with cross-trends, and variety and quantity of mineralization found even with limited prospecting. Comparisons with southern 'British Columbia and the U.S. Cordillera suggest that further exploration will result in discovery and development of more major ore deposits and reserves which will eventually revolutionize economy of mining in Yukon. Such mineral resources, with interior petroleum and natural gas possibilities, and ?huge coastal hydroelectric power potential, are the foundations of a much larger future mining industry in Yukon.

Jan 1, 1958

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By S. R. McCutcheon, D. R. Lentz

"Abstract - The 12.1 Mt Brunswick No. 6 Zn-Pb-Cu-Ag massive sulfide deposit (New Brunswick, Canada) lies between two subaqueous felsic volcanic formations near the base of the Middle Ordovician Tetagouche Group. The footwall comprises rhyodacitic pyroclastic rocks (Nepisiguit Falls Formation), whereas the hanging wall comprises a sequence of rhyolitic flows, breccias, and hyaloclastites (Flat Landing Brook Formation), with an age difference of less than 3 m.y. The Brunswick No. 6 deposit is a proximal autochthonous deposit with a well-zoned massive sulfide body and a basal Cu zone that, at depth, develops into a stockwork stringer sulfide (feeder) system. The massive sulfides are capped sharply by a layered magnetite-chert unit that extends regionally beyond the deposit. The deposit has a keel shape (sheath) formed by the F1F2 interference pattern. The heterogeneous ductile deformation and upper greenschist-grade regional metamorphism has transposed many of the epigenetic stockwork structures and alteration within the host sequence. Hydrothermal alteration is much more extensive, both vertically and laterally, in the footwall (a few 100 m) than in the hanging wall (<100 m). Anomalies farther up in the hanging wall sequence seem to be associated with independent alteration systems related to the rhyolite domes. The least-altered footwall units exhibit keratophyric alteration (albite or adularia) and weak Mg enrichment (chlorite). More intense micaceous (sericite and Mg-rich chlorite) alteration occurs around the footwall sequence. The transposed stockwork stringer sulfides are typically composed of Fe-rich chlorite (± sericite, ± silica) with pyrite, pyrrhotite, chalcopyrite, arsenopyrite, and sphalerite. The (Fe2O3T+MgO)/(Na2O+K2O) and base metal alteration indices are the best practical lithogeochemical vectoring tools at this deposit. Sommaire - Le gîte de 12.1 Mt de sulfures massifs de Zn-Pb-Cu-Ag Brunswick No.6 est localisé entre deux formations volcaniques felsiques sous-marines situées près de la base du Groupe de Tetagouche d’âge Ordovicien Moyen. Le mur consiste en roches pyroclastiques rhyodacitiques (Formation de Nepisiguit Falls) tandis que le toit consiste en une séquence de coulées, de brèches et d’hyaloclastites de composition rhyolitique (Formation de Flat Landing Brook); la différence d’âge entre les deux est de moins de 3 m.y. Le gisement Brunswick No. 6 est un gîte autochtone proximal comprenant un corps de sulfures massifs clairement zoné ainsi qu’une zone cuprifère basale qui passe progressivement à un stockwork de filonnets de sulfure en profondeur (feeder). Les sulfures massifs sont abruptement surmontés d’une unité laminaire de chert et de magnétite dont l’extension par delà le gisement est régionale. Le gisement affecte la forme d’une quille (fourreau) résultant d’un patron d’interférence F1F2. Plusieurs des structures épigénétiques du stockwork et des patrons d’altération de l’encaissant ont été transposés par la déformation ductile hétérogène ainsi que par le métamorphisme régional au faciès des schistes verts. L’altération hydrothermale est beaucoup plus importante, tant verticalement qu’horizontalement, dans le mur (quelques 100 m) que dans le toit (<100 m). Les anomalies situées plus haut dans le mur semblent être reliées à des systèmes d’altération indépendants associés aux dômes de rhyolite. Les unités les moins altérées du mur une altération kératophyrique (en albite ou en adulaire) ainsi qu’un faible enrichissement en Mg (chlorite). Une altération en mica (séricite et chlorite magnésienne) plus intense est présente autour de la séquence du mur. Les sulfures du stockwork de filonnets transposés consistent typiquement en chlorite ferrifère (± séricite, ± silice) accompagnée de pyrite, de pyrrhotite, de chalcopyrite, d’arsénopyrite et de sphalérite. L’indice d’altération (Fe2O3T+MgO)/(Na2O+K2O) et l’indice des métaux usuels sont les outils d’exploration les plus appropriés dans ce gisement."

Jan 1, 2006

By James McMahon

Although doubt has been expressed many times as to who first brought self-contained breathing apparatus to this side of the Atlantic, there is none whatever that the first organized station was established at Glace Bay, N .S., by the Dominion Coal Company, in 1907. This station was started with 20 sets of 1907 "Draeger" apparatus and all necessary station equipment and supplies. After the fire at No. 1 pit, Sydney Mines, in 1908, the Nova Scotia Steel Company installed 15 sets of "Draeger" and sup-plies, which were housed in a rescue car (a converted pull-man.) In 1909 or &apos;10 a fire occurred at the Back Pit, Stellarton, where the apparatus from Glace Bay was used, and subsequently the Acadia Company erected a station and in-stalled 10 sets of "Securitas" apparatus. In 1912 the station at New Waterford was opened and equipped with "Draeger," and the same year the station at Springhill was built and equipped with the same type. Sometime during past years the Nova Scotia Steel Company acquired a couple of "Proto" machines, and after the explosion at the Allan shaft in 1918 the Acadia Coal Company added some "Gibbs" to their station. From this it will be seen that when the coal-fields were organized under the British Empire Steel Corporation the equipment was rather mixed, therefore steps were taken by the executive to stanardize the whole of the rescue and recovery work.

Jan 1, 1924

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners&apos; fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By E. G. Joe

The continuing increase in costs for power and fuel are affecting significantly the cost of milling Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors, carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that, in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc .ore mills were moderate in energy consumption, and uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. Although plant heating costs varied somewhat with location, it was apparent that the lowest heating costs were achieved by those plants built with proper insulation and energy conservation design. If the cost per million British thermal units is taken as $2.00, the mill energy costs generally ranged from 40ft to $1.20 per ton.

Jan 1, 1979

By J. F. Henderson

THE National Advisory Committee on Research in the Geological Sciences was established seven years ago - in 1949. In 1952, shortly after the Committee had really begun to function and had issued its first report, a paper ( l) was presented describing the objectives and organization of the Committee and the progress to that time. Another four years have gone by and the Committee feels a further progress report may be of interest. HISTORY Ten years ago, in 1946, the Geology Division of the Institute set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. Hawley, recommended that "a National Advisory Committ.ee on Research in the Geological Sciences be formed" (2). With the backing of the President and Council of the C.I.M. this recommendation went forward to the then Minister .of Mines and Resources and, with his approval, to the Committee on Scientific and Industrial Research of the Privy ?Council. As a result, the National Advisory Committee was set up in 1949.

Jan 1, 1956

By C. S. Gibson

INTRODUCTION I WELCOME the opportunity to speak on Programmes in Safety. The invitation to do so shows that those guiding affairs of the Institute in this District realize the practical importance of this subject. My remarks are intended primarily for mines having 100 to 400 employees, approximately. With minor modifications, however, they apply also to larger or smaller operations. Others, I hope, will derive benefit from this paper, for they, too, have a part to play in accident prevention; for example, contractors such as shaft-sinkers; manufacturers of equipment; and consultants and designers of mining, milling, and metallurgical methods. These troubled times stress, as never before, the importance of efficient operations in mining. The days are gone when neglect can be afforded. Safe working conditions and satisfied employees are essential for efficient production at reasonable cost. The mining industry of Ontario long has been keenly aware of the human aspects of this subject, and as a whole it has done much to decrease the frequency and severity of disabling accidents. The number of fatalities per 1,000 employees has been reduced from a high of 5 some two decades ago to an all-time low of 0.89 in 1948; the incidence was slightly higher in 1949, being 1.17 per 1,000. The reduction in non-fatal compensable accidents also has been outstanding, frequency having ?been reduced from over 200 per 1,000 employees some two decades ago to 54 per 1,000 at the producing mines in 1949. These statistics demonstrate progress. Nevertheless, the general picture still leaves much to be desired when viewed from two other angles.

Jan 1, 1951

By S. J. Cook

Copper, a world commodity, and the first metal used by man, played a great part in the beginnings of modern civilization, which rests so dependently on the utilization of metals. Then, long after the close of the so-called &apos;bronze age,&apos; when iron and steel had attained great prominence as the world&apos;s most important metals, the practical application of electricity to industry and commerce, for the improvement of every phase of man&apos;s multitudinous activities, gave a new impetus to the production of copper. Improved metallurgical practice made it possible to work low-grade properties at a profit. Research disclosed many new uses for copper. The metal, now produced from the mines of the world in the proportion of about one pound to every 50 tons of pig iron, has attained an importance which rivals that of iron and steel in the commerce and daily life of every nation. New fields of copper-bearing ore have been discovered in Canada in recent years. Established mines in the United States and Chile are producing on a great scale. Africa looms up as one of the great question marks in the future of copper. Whereas, a few years ago, the end of the world?s resources was predicted as being in sight, the evidence now available seems to show that the copper production of the world is likely not only to continue, but to increase for a long time yet to come. Canada&apos;s future in copper is a great subject; in the present paper only a few of the most outstanding factors affecting Canada&apos;s destiny in this large field may be noted, but if consideration of the points raised herein serves to focus attention on the magnificent possibilities of Canada as a producer of copper, the preparation of the paper will be more than justified.

Jan 1, 1928

By K. D. Bulin

"An interesting brief history review of shovels as the primary excavating tool will permit the reader to see that immeasurable development and resources have preceded the shovel excavators which today are used extensively throughout the mining industry. With this as a background, the shovel manufacturer has the ability to utilize his resources best in those areas of shovel development in which the maximum benefits of increased reliability, performance and ease of maintenance will improve the operating rewards to the user of the equipment. The author explains the function of the shovel as a part of the material handling system. A detailed description of those areas of the shovel in which the most recent developments and major improvements have been implemented in the manufacture of the shovel excavator arc included."

Jan 1, 1973

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By I. Southern, S. Kelebek

"Smelting furnace bricks contain significant quantity of base metals trapped in refractory material. A series of flotation tests were carried out on samples of old bricks from Sudbury area to examine upgrading behaviour for recycling purposes. Depending on the grind size used nickel recoveries varied from 60 to 90.6% with corresponding grades of 20% and 14.7%Ni. There is a trade-off between nickel and copper. The nickel has responded well to fine grinding, however, the copper recovery suffered from it. Mineralogical characteristics and flotation behaviour of the brick material are discussed in reference to those from the primary ore. INTRODUCTIONMineral processing is well recognized as a mature technology not only for the mining industry, but also for the environmental industry for the purpose of remediation and recycling. Materials available for recycling are usually the products of many years ago. There are multiple stake holders in this area. In general, when the processing results in a product that can be reused or sold, the company carrying out the remediation makes a profit, while the regulators and the public are pleased due to a cleaner environment. From these points of view, there have been many papers published over the years on various mineral processing techniques applied to separation of many different materials including from mining and metallurgical industries (Wilson et al., 1994; Tsunekawa et al., 2005; Saikia et al., 2012).Flotation may be viewed as the backbone of the mining and metallurgical industry since its invention for separation of solids from one another almost a century ago. It is capable of recovering a variety of finely divided different solids following their liberation from each other. Its versatility and highly competitive nature in terms of cost per tonne of material processed, accounts for its occasional uses in the environment engineering area. In the mining industry, flotation is the standard method used for the sulphide ores. It can be applied as a bulk flotation and/or differential flotation. Bulk flotation, which refers to co-flotation of several components from their source, is most suitable for environmental cleanup objectives. Desulphurisation of various plant tailings is a typical example of this (Benzazzoua et al., 2000)."

Jan 1, 2012

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By Unkown

To the Membership of the Institute Gentlemen: The Mineral Industry of Canada in 1948 The preliminary estimate issued by the Dominion Bureau of Statistics and tabulated in the Bulletin of January, 1949, indicated that the value of Canada&apos;s mineral production in 1948 reached an all-time high of $808,180,216, showing an increase of 25 per cent over the previous record of $644,696,007 established in the preceding year. The output value of metallics was increased by 22.4 per cent; of fuels, by 43.7 percent of other non-metallics, by 19 per &apos;cent; and of structural materials, by 16.8 per cent. The value of metals produced in 1948 at $483,770,759, was about $87,000,000 more than in the previous year. There were substantial increases in the tonnages of copper, lead zinc nickel, and other base metals produced, but the rises in market prices for such metals accounted for most of the gains in output values. Production of gold at 3,495,403 ounces valued at $122,339,105 indicated an increase in volume of approximately 500,000 ounces and an increase in value of 14 per cent. Despite the benefits provided under the Emergency Gold Mining Assistance Act 1948 the volume of gold produced in the year was still nearly 2,000,000 ounces less than the record of 5,300,000 ounces established in 1941. The value of mineral fuels produced in 1948, at $158,787,255, was 44 per cent above the 1947 total. Coal production at 18,431,250 tons valued at $107,298,757, while substantially higher than in the preceding year was still half a million tons below the record reached in 1942. Striking developments in the Leduc field in Alberta were responsible for bringing the output of crude petroleum in the year to a new high of 12,098,166 barrels, valued at $36,858,959.

Jan 1, 1949