Search Documents

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By L. F. Haven

"The desirable shovel speed-torque curves are described, along with the characteristics of the more important electrical components used to approximate these curves. A particular shovel regulator system combining these components is discussed in detail and some of the advantages and disadvantages of the system are given.INTRODUCTIONIN 1959, STATIC CONTROL was for the first time successfully applied, installed and operated on a mining machine in North America. Since that time, a great deal has been learned about this control by the people maintaining these machines as well as by the de-signers.In 1961, the first SCR (Silicon Controlled Rectifier) or thyristor control system was installed on an excavator. This control differed from the earlier static control in that thyristor excitors supplied the generator fields directly. The development of thyristors of a sufficient rating to supply amounts of phase-controlled power to the generator fields eliminated the bulky Mag. Amp. -Rectifier combination previously used."

Jan 1, 1969

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada's mineral production, chief basis of the nation's post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By George J. Simandl, Donald F. Gunning

At the beginning of the 20 century, British Columbia produced a wide variety of quality dimension stone products for both domestic and foreign markets. The industry flourished until the 1930s when most of the producing quarries closed as a result of the Depression. During the 1990s, British Columbia experienced the resurgent North American dimensional stone production trend. The industry benefited from increased prospecting activity and from substantial new investment in processing equipment, particularly in the granite sector. These activities resulted in new quarry developments, the reopening of abandoned quarries such as on Granite and Fox Islands <www.quadrastone.com>, and a renaissance in downstream value-added activities. British Columbia has reestablished itself as an important, reliable and innovative source of high-quality stone products.

Jan 1, 2001

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By J K. Irwin

The authors discuss the application of drum and friction hoists under modern conditions and give four examples of friction hoists proposed for various applications. The paper concludes with a summary of the advantages and limitations of friction hoists relative to drum hoists. Introduction T H~ introduction of the multiple-rope friction hoist m the late 1940&apos;s has complicated the se-lection of the right hoist for a given job. Once such considerations as rope safety factor, drum to rope ratio, hoisting distance, tons per hour and/or service duty have been decided upon, the selection of a drum hoist is relatively simple. We now ask our-selves "which hoist -drum or friction? (See Figure 1 and Figure 2). When a friction hoist is a possibility we are immediately concerned with how many ropes to use, whether to hoist balanced or counter-balanced, whether a friction hoist will be flexible enough for the application and, of course, what the relative costs will be.

Jan 1, 1964

By T. Banerjee, Y. Dumais, R. Lemire

"Agnico Eagle LaRonde produces over 300,000 ounces of gold annually, along with silver, zinc and copper by-products. The LaRonde plant consists of a conventional SAG and Ball mill circuit, followed by flotation. Load management is imperative for maintaining stability in grind size and ensuring consistency of the flotation feed. In flotation, the mass pull profiles of the cells and reagent dosage rates need to be managed to maximize recovery, while maintaining product quality. This is achieved by controlling the air, level and reagent addition set-points across the circuit. However, disturbances such as feed size distribution, ore hardness and mineralogy make it challenging to maintain efficient control using traditional control techniques. LaRonde therefore worked to develop a progressive control strategy, targeting stability and optimization. This started with a year-long instrumentation upgrade campaign, focusing on optimizing the performance and reliability of plant-wide instrumentation. The process was then optimized, leveraging AwaRE advanced controllers running in closed loop with PARC modules embedded within the PLC. The installation of 8 PFC cameras in flotation changed the flotation operation from a level and air control based strategy, to one that controls mass pull. This new control philosophy has allowed the plant to effectively manage mill load, improving grind size and providing increased throughput with better flotation performance.INTRODUCTION Background Since 2015, Agnico Eagle LaRonde has been conducting an optimization campaign to maximise the performance of plant assets leveraging instrumentation and control. The grinding and copper flotation circuits were identified as the areas having the greatest opportunities and value proposition for advanced control. A disciplined approach was followed to design and implement a progressive control solution to achieve operational excellence."

Jan 1, 2018

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By V. A. Preto

The Rexspar uranium deposit is located approximately 5 kilometres south of Birch Island, B.C. Three separate zones of commercial-grade uranium mineralization mineable by open pit have been outlined. Uranium and fluorite-celestite mineralization occur in a trachytic member of alkali-feldspar porphyry, lithic tuff, tuff breccias and pyritic schist conformably interlayered with a succession of strongly deformed greenschists and fragmental rocks that are, in large part at least, of volcanic origin. The age of these strata is not precisely known, but they are considered as part of the possibly Mississippian Eagle Bay Formation. Commercial-grade uranium mineralization is always associated with fluorphlogopite-pyrite replacement of the trachytic unit and is contiguous to, but separate from , a zone of ore-grade fluorite mineralization. In all zones, ore occurs in lenses of variable thickness and lateral extent, which lie parallel to the schistosity of the trachytic rocks and surrounding greenschists. The principal radioactive minerals at Rexspar have been identified by other workers as uraninite, uranothorite, bastnaesite, torbernite and metatorbernite. Considerable amounts of thorium oxide and widespread rare earths have been reported from all three radioactive zones. The geology of the deposit suggests that the trachytic rocks represent a highly differentiated intrusive-extrusive system in which fluorphlogopite, pyrite, fluorite and uranium-bearing minerals were deposited late in the evolution of the system by deuteric, volatile-rich fluids. The considerable amounts of thorium and widespread rare earths associated with the uranium tend to support the thesis that this element is of primary origin rather than secondary.

Jan 1, 1978

By Fei Dai

Musculoskeletal disorders (MSDs) are a group of painful disorders that affect muscles, tendons, nerves, joints, cartilage, and ligaments. They are a serious problem among the workforce in the United States. In the construction industry, high physically demanding tasks expose construction workers to a number of well recognized MSDs risk factors such as repetitive motion, high force exertion, and awkward body posture. Finding ways to effectively identify and evaluate risks of MSDs can significantly alleviate this problem. To this end, this paper reviews state of practice and research in the assessment of risks of MSDs among construction workers, in which a number of biomechanical models have been developed to evaluate joint and tissue loading with the aid of state-of-the-art remote sensing technologies. Findings from the review reveal that despite the advances in tracking human motion and muscle activities, current remote sensing approaches still involve sophisticated instrumentation and expensive experiment setup. These factors greatly limited the applicability of such approaches in real construction settings. How can we detect and evaluate the construction worker?s MSDs risk in real work environments? In this paper, strategies by utilizing video surveillance systems are presented, to set the stage for addressing the above question and discussing future research in real-time, marker-less, and costeffective MSDs risk assessment.

Aug 1, 2013

By R. R. Rogers

Abstract The degree of cathodic protection of steel and the anode corrosion rate were determined when anodes and waters of different compositions were used at temperatures similar to those in domestic hot water tanks. Twenty different anode materials, sixteen of them magnesium-zinc-aluminium alloys, were immersed in six different synthetic waters resembling those to be found in various parts of Canada. The results showed that (1) both the degree of cathode protection and the average anode corrosion rate are affected materially by the composition of the anode material and of the water; (2) poor cathode protection is associated with low anode corrosion rate; (3) when the cathode is fully protected, the anode corrosion rate may be comparatively low or comparatively high, depending upon the composttion of the water; (4) an important relationship exists between the magnesium content of the preferred anode and the composition of the water; (5) the degree of protection is increased as the SO4 + Cl concentration of the water is increased and thus as its specific resistance is decreased. Introduction Fairly recently, the use of the active metal magnesium for the cathodic protection of less active metals has received a considerable amount of attention. This interest has been stimulated by the fact that the wartime demand for magnesium was greatly in excess of the present peacetime demand and there is a natural desire to continue operating the large magnesium plants which were built during the war. Information regarding the use of zinc and aluminium for this purpose also has been published. There is a great demand for domestic hot-water tanks which will resist corrosion satisfactorily. This problem is rather complex in view of the fact that the composition of the water used in such tanks varies greatly and depends upon the locality. The present investigation deals with the effect of water composition and anode composition on the cathodic protection of steel under conditions approaching those which exist in hot water tanks.

Jan 1, 1948

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35&apos;W, latitude 49°25&apos;N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"Abstract -The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack&apos;s Pond, Daniel&apos;s Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and fine­ grained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack&apos;s Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. AU are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack&apos;s Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-rnassive pyrite + chalcopyrite are known.The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to host polymetallic massive sulfides.Daniel&apos;s Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit Jacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, Jess deformed volcanic­ sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

By Webber. G. R.

Variation in content of some of the major and minor elements in the Lake Dufault granodiorite near Noranda, Quebec has been studied. The element variation and specific gravity data show a pattern consistent with the concept of a concentrically zoned intrusive on the western side of Lake Dufault with a potassium-rich core and a calcium-rich inner zone. The part of the intrusive on the eastern side of Lake Dufault is of more problematical origin, but the suggestion is made that it has resulted from assimilation of volcanic rock by the intrusive. THE purpose of this investigation was to test the application of x-ray fluorescence analysis to the study of variation in chemical com-position of the Lake Dufault granodiorite. The Lake Dufault granodiorite is an intrusive body approximately six miles long by three miles wide located four miles north of Noranda, Quebec. This intrusive is of particular interest because of its -

Jan 1, 1962