Search Documents

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

By R A. Pax, B Cornish

Increasing the throughput of the MMG Century operation by over 25% from past practice to preserve cash flow close to the end of life of mine has revealed new throughput and load dynamic instabilities in the SAG mill causing significant time averaged loss of production. A twelve microphone array around the SAG mill (Pax, 2014) using the non-contact acoustic measurement methodology (Pax, 2011, 2012) has been used to diagnose the new dynamics. Dynamic acoustic noise signal information allows discrimination of the behaviour of the steel balls and the rock. Determination of mill load, toe and shoulder angles, water holdup, and proxies for mill load are possible.The instability was diagnosed with the help of an abnormality in the liners/lifters of the SAG mill with one row of lifters having a slightly increased in-mill life compared to the rest. The steel shoulder angle is observed to be disturbed cyclically at a rate of precisely one revolution at low throughputs of 750 t/h. However, at throughputs closer to 1100 t/h, the cyclic signal disappears indicating additional dynamics to randomise the repetitive behaviour of the mill charge. The cyclic signal has been used to operate the SAG mill with improved stability at 1100 t/h by adjusting the feed water addition rate.This paper presents and discusses these results and proposes the suggested origin of the extra dynamics. A small consistent aberration of the lifters circumferentially provides a useful detector of stable mill operation and a novel sensor for the dynamics of the internal operation of a SAG mill.CITATION:Pax, R A and Cornish, B, 2015. A novel measurement for the internal operation of a semi-autogenous mill using acoustic sensors – a case study, in Proceedings MetPlant 2015, pp 120–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By S Telford, J Weir

Heathgate Resources Pty Ltd (Heathgate) operates the Beverley Uranium Mine in South Australia, located on the plains between the northern Flinders Ranges and Lake Frome some 600 km north of the state capital Adelaide. The uranium orebody exists in permeable sands within the confined, highly saline Beverley aquifer, approximately 125 m below the ground surface and the uranium is mined using in situ recovery (ISR) technology. The Beverley mine is a highly technologically advanced ISR mine and is operated in accordance with stringent safety and environmental standards. The mine is currently licensed to export 1500 t of uranium oxide (U3O8) per annum. This paper outlines the fundamental differences between ISR operations and the more traditional uranium production methods, such as agitation leaching and heap leaching, where the ore is removed from the deposit, stockpiled, crushed, milled and leached on the surface. Solids tailings from either the mill or the heap are finally deposited in a tailing storage facility. ISR mining differs from conventional mining because the ore remains in place underground (in situ) and the groundwater contained in the ore-bearing aquifer is utilised as the mining fluid. This is achieved by drilling into the deposit and installing wells for extracting and re-injecting the groundwater which is fortified with chemicals. The fortified groundwater (ie mining fluid) flows through the permeable sands containing the orebody, dissolving the uranium. The pregnant mining fluid is then collected and transferred to the recovery plant where the uranium is captured (on ion exchange (IX) resin in the case of Beverley). The barren mining fluid is then re-fortified and recycled to the wellfields. Once mining is completed in a wellfield, the surface infrastructure is relocated to a new wellfield, and the mined-out wellfield is rehabilitated to its original surface condition. A comparison of 'standard' hydrometallurgical plants, heap leach and ISR shows a number of key differences, such as the rate of leaching, the level of control available to the operators, and the type of contact/reaction that occurs. While limited in its applications, ISR mining has proven successful at Beverley and provides another mining and processing method for the production of uranium.

Jan 1, 2008

THIS paper proposes to give a general description of the pumping and other machinery in use at the Thames Hauraki Pumping Station, situated on the Thames goldfields of the North Island, New Zealand. An idea of the general arrangement of the pumping engines and pumps can be obtained, together with a certain amount of detail, by reference to the illustrations. The history of the pump is rather interesting, and is as follows: -In 1894 the Government decided that a subsidy of £1 for £1up to an amoUllt not exceeding £25,000 be granted towards the erection of suitable machinery to exploit the Thames low levels.With a guarantee of such assistance a company was floated in London, with a capital of £300,000, to develop several properties at Thames. As the old Queen of Beauty Company had produced bullion worth £400,000 prior to closing down on account ofa breakdown to its pumping gear, their shaft was chosen as the site of the principal work. As soon as the company was floated, operations were commenced at the Queen of Beauty shaft, situated at the entrance of the Waio-Karaka Creek, and not more than about half a mile distant from the principal mines on the field.

Jan 1, 1912

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By D M. Menne

This paper is intended to give a general review of current gold extraction technology for free-milling or non-refractory auriferous ores. Fundamental process concepts and some of the differences between the current technologies is referred to. Typical flowsheets and layouts are provided and it is demonstrated that technology for extracting free-milling gold is relatively simple. For environmentally sensitive areas such as encountered in New Zealand relevant cyanide decay and destruction technology is also discussed. Brief mention is made of some likely future innovations. Finally reference is made of New Zealand's previous significant contribution to gold extraction technology. These contributions were pioneering ranging from the cyanide leaching of gold to adsorption by carbon and precipitation by zinc. New Zealand has not allowed its potential gold projects to develop at a rate commensurate with the rest of the world thereby stifling its renowned innovative approach in this technology. It is time for New Zealand mining to recognise its unique opportunities in developing gold extraction technology and again take a rightful place in leading the way.

Jan 1, 1986

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

Being a geologist I intend describing the renaissance of the gold industry in Australia within its geologic framework; there is a geological pattern to the numerous gold projects which have been brought on stream over the past decade. We are now about midway through our third and largest gold boom which, at a peak of 7.5 million ounces is about twice the production peaks achieved in the preceding booms. From discovery in 1851 through 1870 we saw the first boom largely based on alluvial production in NSW and in Victoria at the great Ballarat and Bendigo Goldfields. The discovery of the Golden Mile in Kalgoorlie, Western Australia, underpinned the second gold boom in the period 1895 - 1915. On that basis the present boom should last through the next decade.   It has been a golden decade for Australian gold production. From less than ten mines in 1980 with production over 10 000 ounces and the largest, Telfer, with output of about 130 000 ounces we now find over 130 deposits being worked around the country today that produce over 10 000 ounces with the largest, Boddington, having an output of over 400 000 ounces. In total these mines produced an estimated 210 tonnes of gold in 1989 and we expect this year, 1990, that a new record production of between 240 and 250 tonnes will be set. This positions Australia in third place in the Western World behind South Africa #1 and the USA #2 and fourth in the world with the Russians holding second place overall behind the South Africans.

Jan 1, 1990

By Sie A

After completing a feasibility study in 1987, Niugini Mining Limited (NML) obtained five Gold Mining Leases within PA 632, covering the Mount Victor and Clarkes Ridge gold deposits. Reserves prior to mining were 260 000t at 3.63g/t Au for Mount Victor and 40 000t at 2.8g/t Au for Clarkes Ridge. Ore was mined from the two deposits by NML from November 1987 to January 1990. A total of 645kg of gold and 346kg of silver were produced from 198 000 tonnes of ore pro- cessed. Mining and milling operations ceased in February 1990. Since then, there has been significant progress in rehabilitating and revegetating the site. Plant and workshop facilities have been dismantled and removed from site, exposed parts of the pit have been landscaped and replanted, tailings water has been neutralised and discharged, and the dam filled. All remaining personnel and equipment left the site in November 1990. It is envisaged that the replanted areas will be rapidly revegetated, leaving little evidence of mining. Niugini Mining did not recoup the initial investment for Mount Victor, but the mine produced a positive cash flow and made a significant' financial contribution to the local communities and Papua New Guinea as a Whole.

Jan 1, 1991

Clinoptilolite as a Low-Cost Solution to Remove Heavy Metals from Water in Mining and Mineral Processing Industry

Sep 13, 2010

By Edwards A. B

Renison Bell is on the Emu Bay Railway, midway between Zeehan and Rosebery on the west coast of Tasmania. The tin deposits in this area have been described by G. A. WaIler (1902), L. K. Ward (1909), H. Hermani (1914), and Hartwell Conder (1918), for the Tasmanian Geological Survey. The ore-bodies occur in the slates, grits, altered lava flows and tufts of the Dundas Series, and consist of fine-grained cassiterite disseminated through massive sulphides (chiefly pyrrhotite or pyrite), or through bodies of quartz and sulphides. Some of these bodies show a N.W.-S.E. strike, parallel to the strike of the tin belt, but others strike N.E.-S;W. or E.-W.The ore-bodies are of two types: (1) steeply dipping fissure veins,' spoken of locally as "feeders," and (2) flatter-lying bodies more or less conformable with the bedding planes of the slates (bedded veins), spoken of locally as "floors."The feeders range from 5-12 ft. in width, with occasional bulges as great as 4q ft. Their lengths vary from 100 ft. to several hundred yards, and they are known to continue to Clmsiderable depths. 'They dip steeply, generally at angles of 45° to 60° to the east or south.The floors, where they occur, 'are directly connected with the feeders, and are sheet-iike bodies of sulphide ore. The composite ore-bodies thus have the shape of an inverted L, or a T, according to whether 'the floor extends out from one side or both sides of the feeder. Most of the floors extend from the hanging-wall side of the feeder. Where erosion has removed the connection, they appear as separate bodies.The feeders as a rule carry more quartz and arsenopyrite than the floors, and are richer in tin. In addition, the cassiterite tends to be coarser grained in the feeders than in the floors. The floors, on the other hand, carry a greater proportion of -sulphides, chiefly pyrrhotite, and the grade of ore and grain size of the cas,siterite tend to decrease as the floor is followed down the dip away from the feeder, so that the outer and lower extremities of the floors may be too low-grade to work economically. The average grade of the ore worked at present is 0·9,0/0 tin. The slates forming the roofs of the floors are commonly much contorted and silicified,' so that they form hard rocks in which the contortion and shattering of the original slates are well preserved. Joints extending upwards, more or less at right angles to the roof of the floor, are occasionally filled with finely crystalline quartz, similar to that in the orebodies, and are often rich in tin, so much so that the slate as a whole may average 0·4% tin.Some carbonate gangue is present in all of the ore-bodies, commonly on the footwall side, and, in places it becomes an important constituent...

Jan 1, 1943

By Paterson R. G, Compston W

The Mine granite at the Ardlethan tinfield is dated by Rb-Sr on a muscovite concentrate at not less than 417 ± 2.5 Ma (2s), consistent with the intrusion of this granitic body into folded Late Ordovician sediments. A combination of Rb-Sr and K-Ar evidence suggests a slightly younger age, 41O ± 2.5 Ma, both for the neighbouring Ardlethan Granite and for the hydrothermal alteration of the Mine granite, with which the tin is associated.On this basis, the somewhat high 206Pb/204Pb of two galena samples from within the hydrothermal alteration zone is best explained by an increase in U/Pb of order 10 per cent during a geochemical event in the Late Precambrian, in the rocks which eventually yielded the Pb to the mineralising fluid. This earlier event probably increased Th/U in these rocks as well, by as much as 5 per cent. If these reconstructions are valid, the lower-than-average U/Pb implied for the original Precambrian source rock bespeaks a mantle component of marginally greater proportion than for "average orogene".

Jan 1, 1982

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

Societal expectations about how the industry operates and treats its people will be a key driver in the development of the Australian mining industry over the next 20 - 30 years (Moffat, Mason and Littleboy, 2009). Understanding these expectations will be critical in maintaining what much of the minerals industry calls its 'social licence to operate', or its public acceptance or approval. Yet what constitutes this social licence is poorly articulated, with little published research exploring the concept at a local operational level or at the national level in Australia or internationally. This research aimed to explore the societal expectations of the mining industry in Australia and test a participatory methodology to articulate them. Three workshops were conducted with a sample of 24 members of the 'Australian voting public' to explore community objectives for the onshore exploration and mining industry, and the underlying expectations for how the industry should operate in the future. Qualitative analysis of this data revealed three overarching objectives for the onshore mining industry held by participants. They thought that the industry should: advance Australia's national interests (including social well-being); minimise environmental impact, and; act in a socially responsible manner. Within each of these three key themes, or objectives, a number of tensions were evident in the views of participants regarding the trade-offs they are willing to make to secure economic benefit from mining, as well as the basic conditions for socially acceptable mining. These data provide an insight into the conditions for a national social licence in Australia for the mining industry, and the means for its realisation.

Jun 1, 2010