Search Documents

Review of the mining legislation in New Zealand has coincided with a number of radical changes. These include a redirection of economic management towards a more open and competitive economy; major reform of the state sector aimed at greater efficiency, transparency and accountability; a new environmental administration; and a fundamental review of policy for management of natural and physical resources. These changes provide an opportunity to develop a consistent and coherent approach in the minerals and related statutes that will achieve objectives of economic efficiency, equity, practicability and good environmental management.

Jan 1, 1987

Gold recovered on the strikes at the Central Norseman mill, Norseman, Western Australia, has an approximate assay fineness of 850. Bullion recovered from the cyanide plant at the mine is of much lower value, and occasionally its assay fineness has been as low as 250. This indicates either that the fine gold particles in the ore consist of an alloy richer in silver than the coarse particles or else that a silver mineral, as well as the gold, is dissolved by the cyanide solutions.It had been observed at the mine that the amount of silver in the bullion appeared to increase when galena appeared to be more abundant in the stoped ore. Interest was, therefore, attached to the possible occurrence of a silver mineral associated with galena and, at the same time, soluble in cyanide.Four specimens of ore from different horizons in the mine were collected by the mine staff for examination as to whether any marked difference in the fineness of gold was apparent on a polished surface and for determination of the silver minerals. As the Norseman ore-body is a quartz reef containing a very small percentage of sulphide, the specimens were selected either because they cont;:lined free gold or because they were, relatively rich in sulphides. They were obtained from the following localities at the Phoenix shaft.1. Level 16, section 28.2. Level 16, section 31.3. Level 8, section 31.4. Level 14, section 38.Specimens Nos. 1 and 2 were thus obtained from different positions at the same mining horizon, while specimens Nos 2 and 3 were obtained from different levels in the same vertical section of the mine.All the specimens consist of quartz characterized by thin, discontinuous seams of sericite and the presence of a little ankerite. Gold and sulphides tend to be localized along these seams, but particles of gold and sulphides are also scattered throughout areas of white quartz. This scattered distribution of the sulphides in relatively wide areas of quartz has involved the preparation of two or more polished sections from each specimen.The outcome of the microscopical examination of these specimens has been to determine that there is no appreciable variation in the colour of the polished particles of gold and, therefore, no marked difference in the amount of silver alloyed with the coarse and fine particles. The presence of small quantities of the tellurides sylvanite, hessite and altaite has been revealed, and found to vary in abundance with the abundance of galena.

Jan 1, 1944

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

By Rogerson R, Queen L

The petrology and age of mid Cretaceous to Palaeogene marine volcanics may provide important clues to the palaeogeography of the period, particularly for tectonic elements and events outboard of the Papuan Basin. This initial survey of known marine volcanics of this age reveals a paucity of reliable data on isotopic ages, geochemistry and syngenetic mineralisation on virtually all units. Existing data allows a tentative subdivision of known marine volcanics into either MORB-like early Palaeogene rifts/ marginal basins, early Palaeogene ensimatic arc rocks overlying ?Late Cretaceous and Palaeogene fore-arc/marginal basin crust, late Palaeogene ensimatic arc rocks, and mid to Late Cretaceous ensialic rift rocks. Due to lack of data, some units are difficult to classify into these categories.

Jan 1, 1991

The Phoenix mine on the Mararoa Reef at Norseman, Western Australia, provides an outstanding: AUstralian instance of the recurrence of payable ore beneath the bottom of an abandoned mine, and an interesting and instructive example of the development ofideas with regard to ore recurrence in a particular district. The Mararoa Reef is the most productive of several hypothermal goldquartz vains in pre-Cambrian basic volc81olics which strike northsouth and dip on the average, 45 degrees east. The Phoenix minewas abandoned at 500 ft. vertical depth after producing 342,000 tons of 9.9 dwt. recovery grade (equivalent to nearly half of the total production of the Norseman field) from a 2,500 ft.. long, horizontally disposed oreshoot, which is reported to have had an ore outcrop only 30 ft. in length.Interest in the field was revived in 1933, and by 1941 new ore mined and developed on the Mararoa Reef by Central Norseman Gold Corporation N.L. amounted to approximately 700,000 tons of 6.7 dwt. recovery grade. In the same period another oreshoot of similar size and grade was developed by Norseman Gold Mines N.L., south of the old Mararoa company's site. As shown by the plans, the ore occurs in discontinuous shoots. The intervening area of shear is poor in quartz as well as in gold. Geological work on behalf of Western Mining Corporation Ltd., and Central Norseman Gold Corporation N.L. has been in progress in the mine and in the field more or less continuously from 1913 to 1941 and again since 1946. This paper describes the successive advances in the understanding of the exploratory problem up to late 1941, to which several investigators have contributed. It is published by permission of the Board of Directors of Central Norseman Gold Corporation N.L., owners and operators of the Phoenix and other mines.Development of the Prospect.In 1933 Western Mining Corporation acquired an option over the Phoenix property and adjacent leases. H. E. McKinstryl visited the mine and recognised that the ore occurred primarily on the flatly dipping sections of the vein, as distinct from the steeply dippingsections, in a wide shear zone with reverse movement. Many of the flatly dipping fractures were seen to exhibit tension phenomena and to link one shear plane to the next below on the footwall side. The flat links carried much more quartz than the steeper shears.Later, H. J. C. Conolly, assisted by J. D. Campbell, examined the prospect and by contouring the vein with reference to an inclined...

Jan 1, 1950

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Dodd SF

Valuation of mining companies and their underlying assets prepared by brokers' analysts are, by necessity, approximations. The reliability of the valuations is entirely proportional to the quality of available data, the reliability of forecasts and the nature of underlying commodity price assumptions. The latter is perhaps the greatest single cause of gross variations in company and asset earnings estimates and- valuations. Assumptions are often necessary regarding commodity price achievement based on commodity hedge positions. Public disclosure from listed companies provides a sound base from which to project earnings, cashflows and balance sheets. The uncommon disclosure of projected production and cost schedules often reduces the reliability of future estimates. The application of reserve and resource estimates is contentious with practitioners applying differing weightings to importance of resources in estimating mine lives (and therefore cashflow streams). Valuation methods applied in equity markets usually focus on relative value and the identification of pricing anomalies. The commonest ""rules of thumb"" applied in the valuation of mining companies (and therefore their underlying assets) is with the use of year specific price/earnings (P/E) and price/cashflow (P/CF) ratios, with low multiples suggesting undervalued assets, high multiples overvalued situations (but these rules can often be clouded by market expectations of underlying commodity price movements). Another simply applied valuation tool is to examine the examine the value placed on reserves and resources by the market. Inexpensive gold in the ground (expressed as $ of market capitalisation per ounce of reserves or resources) might indicate a buying opportunity, but the market does discount the value of gold in the ground prior to mine development and where development risk is perceived.

Jan 1, 1994

By L D. Queen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tifalmin porphyry copper district is located in the Star Mountains roughly 35 km north-east of the Ok Tedi mine. The district is a cluster of temporally and geochemically related porphyry copper deposits and their associated skarns. It covers an area of roughly 10 × 6 km and comprises at least three intrusions (Olgal, Futik and Kum Kom) where drilling has demonstrated the presence of porphyry copper mineralisation, and another three intrusions (Rattatat, Unfin and Pad 48) where porphyry copper mineralisation is strongly suggested by surface investigations and geochemical or geophysical signatures.Copper and gold mineralisation was first discovered in the area in the 1960s as part of the regional exploration program by Kennecott that located Ok Tedi. The mineralisation is associated with poly-phase porphyritic diorites, quartz diorites and tonalites that intrude the Upper Eocene to Middle Miocene Darai limestone and underlying Cretaceous to Eocene Feing Group. Radiometric K-Ar and U-Pb zircon ages cluster between 4 and 2 Ma for both the mineralised and post-mineral intrusions. In addition to porphyry-type mineralisation, variable amounts of calc-silicate and/or magnetite skarn occur near the contact of most of the intrusions. Mineralisation in the Olgal and Futik porphyries occurs as chalcopyrite replacement of mafic minerals and in a stockwork of micro-veinlets. Mineralisation mostly occurs in the intrusions but is also observed in hornfelsed siltstones and sandstones of the Feing Group on the southern margin of the Olgal intrusive body. Quartz veining is uncommon. Secondary magnetite is commonly associated with the highest copper and gold grades. Sericitic alteration is most prominent in the mineralised hornfels. Structurally, the area is dominated by syn- to post-mineralisation thrusting from the north. At least one of the deposits (Olgal) appears to be truncated at depth by a thrust fault.CITATION:Queen, L D, 2015. The Tifalmin porphyry copper gold district, Star Mountains, Western Papua New Guinea , in Proceedings PACRIM 2015 Congress, pp 357–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Geotechnical input is interwoven into the mining process at George Fisher South Mine from the planning and design of working areas to the closure of worked out areas and maintenance of life of mine and long term excavations. The methodology used consists of a mixture of application of established theoretical principles and guidelines derived from successful historical experience. In the development stage, including long term infrastructure excavations, the process takes into account the expected life of the excavation, usage and expected stress changes during its life span. On the stoping stage, the design process takes into account the local rock mass conditions, geological structure setting and previous experience in a particular orebody. Due to the high variation in age of currently used excavations, a rolling monitoring and risk assessment process for long term and life of mine excavations and infrastructure is maintained. This paper has as an output the process that must be followed to ensure an excavation on the highly dynamic mining environment at George Fisher South Mine is blasted and maintained in compliance with applicably commonly accepted safety and industry requirements.

Nov 25, 2010

By C Noble, J Webster-Brown

A survey of selected West Coast Streams was undertaken in Summer 2001, Summer 2002 and Winter 2002 to establish the degree of arsenic (As) contamination in waters and sediments downstream of old coal and gold mine workings on the West Coast. Of the catchments studied, Soldiers/Ford Creek and Rapid Stream showed the most significant elevated As concentrations, predominantly in dissolved form, and evidence of AMD or ARD contamination (high sulfate concentrations and/or acidity). The rate and processes of removal of dissolved arsenic from the water column (attenuation) have been studied in these catchments. The Rapid Stream and Soldiers/Ford Creek catchments are directly affected by adit drainage from the Sullivan and Blackball coal mines respectively. Both catchments have high As concentrations in the sediments, with up to 770 mg/kg in Soldiers Creek and 490 mg/kg in Rapid Stream. Dissolved As concentrations are significantly elevated in the neutral pH waters of Soldiers Creek; typically as high as 100 - 200 ¦g/kg, up to 500 m downstream of the main adit discharge (800 ¦g/kg As). Adit inflows to Rapid Stream were acidic and contained 20 - 30 ¦g/kg dissolved As, with relatively high concentrations of arsenic in the stream water in winter (up to 18 ¦g/kg), but not in summer. Analysis of concentration trends and As:SO4 ratios downstream of these obvious As sources confirmed that dissolved As had been actively removed from the water column, but varied seasonally with greater removal evident in summer. Adsorption of arsenic onto iron oxide in the stream sediments is the most likely mechanism of removal. The Snowy River catchment, on the other hand, has relatively high As concentrations in both the sediments and the water column, but there was little evidence of a distinct AMD or ARD input from the Blackwater gold mining area. Preliminary investigation suggests that dilution rather than attenuation is responsible for decreasing As concentrations downstream.

Jan 1, 2003

By D J. Woodward, A B. Christie, S A. Henrys

Low-level aeromagnetic data available in digital form have been combined to produce a new 1:100 000 scale map of total force anomalies of the Coromandel region, New Zealand. The map incorporates data from 13 surveys flown between 1977 and 1990 and shows the regional magnetic pattern as well as more detailed localised anomalies. In addition to magnetic anomalies, the map also depicts data to aid interpretation, including small-scale maps of topography, geology, magnetic intensity gradient and apparent magnetisation. The primary magnetic anomalies of the Coromandel region are associated with Late Miocene and Pliocene volcanic rocks, but have been locally modified by intense hydrothermal alteration caused by geothermal activity. Epithermal gold-silver and porphyry copper deposits are associated with zones of hydrothermal alteration. The map of magnetic anomalies can be used as an aid to mineral exploration and the interpretation of the processes that control the distribution of mineral deposits in the region.

Jan 1, 2001

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By B W. Riddol1s

The 1983 Energy Plan calls for an increase in North Island coal production from both underground and opencast sources from the 1982/1983 production of 843 000 tpa to approximately 3.4 Mtpa within the ten year period to March 1993. This increased production is scheduled to come from the following sources: Huntly West No 1 underground mine reaching full production of 1.26 Mtpa. Huntly East underground mine increasing production to 750 000 tpa. The proposed new Huntly West No 2 mine producing 100 000 tpa in its first year of operation û 1992. The proposed Ohinewai opencast producing 920 000 tpa for supply to the steelmaking plant at Glenbrook, replacing Weavers opencast which will be worked out in 1990. Rotowaro opencast producing at 220 000 tpa (currently being achieved). Two additional sources of supply which are not scheduled to begin production for at least ten years, and both of which have been designated for coal fired thermal power generation, are the Maramarua and Mokau coalfields. It was originally envisaged that development of both coalfields would be a combination of underground and opencast mines. The form of development is yet to be confirmed by detailed feasibility studies. The location of the Maramarua, Ohinewai (Waikare Coalfield) and Mokau deposits is shown on Figure 1. Worley Consultants Limited, in conjunction with their partners Rheinbraun Consulting GmbH (Germany) and Longworth McKenzie Pty Limited (Australia) have been involved with investigations and mining assessments for the Maramarua, Mokau and Ohinewai prospects. The Maramarua and Mokau studies form part of the New Zealand Coal Resources Survey programme of updating information to the Pre-Feasibility Mining Assessment level before proceeding to detailed feasibility studies. The Ohinewai study was commissioned directly by Mines Division to investigate the feasibility of mining coal by 1989 before reserves at Weavers opencast are depleted. This paper describes typical studies which are now being commissioned by Mines Division to investigate large-scale mining development and the effect geotechnical-conditions may have on coal recovery. The magnitude of these projects is reflected in the proposed outputs û up to2 Mtpa from individual mines û and the introduction of new continuous mining systems for both underground and opencast mines on a scale which has not previously been contemplated.

Jan 1, 1984

The placer mining industry of the West Coast region of the South Island is based largely around the production of alluvial gold, although other valuable minerals are also present. Since the first major discoveries in 1864-65, reported gold production has totalled around 264 t (8.5 Moz). During the past 10 years, annual production has totalled around 1460 kg (47,000 oz). It is anticipated that gold production over the next three years will continue at a level of 1400-1800 kg.   Annual gold production peaked during 1866 at approximately 17,170 kg (550,000 oz) and has not exceeded 100,000 oz since 1885. This reflects the ease with which gold was won from shallow, rich deposits that were present at many localities. Subsequently, there has been a general decline in the availability of this type of deposit, a trend that will continue in the future. This paper outlines the present state of placer mining in the West Coast region, gives some historical background to the industry and briefly predicts future trends.

Jan 1, 1997

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

Effect of Grinding Media on the Flotation of Sulfide Minerals

Sep 13, 2010

By S Robotham, P C. Stewart, K Maher

A data science based dilution study was conducted to identify the causes of dilution at South32’s Cannington Mine (Cannington), a large open stoping operation. In terms of industry benchmarks for unplanned dilution, Cannington is already performing very well, and so opportunities for improvement are more difficult to identify. The study is based upon back analysis of nearly 150 case studies from the mines reconciliation database, and has quantified the relative effect and significance levels for the following dilution parameters; time until paste filling, faulting and cable bolt reinforcement. Specifically, significant contributions were associated with faults and stope open duration. Quantifying the effect of faults on stability graph accuracy enabled a site specific adjustment to improve the predictive ability of the Cannington stability graph (unstable stope specificity improved from 63 per cent to 74 per cent). Despite Cannington’s already high levels of stope performance compared to industry benchmarks, data science methods have identified a complex interaction between identified dilution factors (ie stope open duration, presence of faults and cablebolting). Specifically, a third order Factorial ANOVA (Analysis of Variance) provided evidence that stope open duration reduces the effectiveness of cable bolts in faulted ground (average dilution = 2.1 m, p-value = 0.13). These results are consistent with site observations of a relationship between the stope open duration and the extent of failure when unravelling on a fault, even when cables are present.CITATION:Maher, K, Stewart, P C and Robotham, S, 2016. A data science approach to identifying and quantifying causes of dilution at Cannington Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 491–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The dissolution of gold in cyanide has been studied, using both chemical and electrochemical techniques. The electro-chemical studies have confirmed that gold may become passive in cyanide solution if its potential becomes more positive than -O· 5 V v. saturated calomel electrode (S.C.E.). The results of the conventional solution rate tests suggest that, although the solution rate is controlled by the rate of diffusion of oxygen at low oxygen and agitation levels, when these are increased the gold may become passive and its solution rate approach a steady value, or even decrease with increasing oxygen level. The passivity of gold has been shown to be of importance in the solution of small spheres of this metal, and in the extraction of gold from a calcined auriferous pyrite concentrate.INTRODUCTIONAlthough it has been appreciated for many years (McLaurin, 1893, 1895) that dissolved oxygen is a necessary adjunct to the solution of gold by the cyanide process, attempts to quantitatively assess its effect have led to conflicting results. For example, Barsky, Swainson, and Hedley (1934) reported that an increase in oxygen concentration improved the solution rate, but Beyers (1936) claimed that such an increase would reduce the rate at which the gold dissolved.By using an electrochemical approach Kudryk and Kellogg (1954) showed that the diffusion rate of either the cyanide or the oxygen was a controlling factor, and that, if the mole ratio of cyanide to oxygen concentration was greater than 10, the solution rate was proportional to oxygen concentration.These results, although they represent some of the most careful work available, were in direct contradiction to the findings of Mills (1951), who found that gold may become passive in cyanide solution, with a resultant decrease in solution rate.

Jan 1, 1963

Minerals Industry - 5 Year Outlook AusIMM sponsored project Positioning the Minerals industry for the 21st Century Does this seem right for New Zealand?  To ascertain the industry's perceptions of issues and capacity to address them: Industry context and issues Capabilities of professional staff Access to professional staff Balancing supply and demand Industry must do it. Cannot wait for others.   Some observations... Negative image - constrains capacity to influence community and government Major repositioning of professional staff competencies required Existing organisational arrangements and capabilities are under pressure to change Difficult to access professional staff of required capability Facing significant external challenges - with real concern about capacity to address them Prevailing culture not suited to needs of the future High level felt need for change The industry has a choiceà We can define where we want to be and act decisively Or We can respond to the future as it unfolds.

Jan 1, 2000