Search Documents

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

The series of events leading to the adoption of more complex flotation circuits for coal have been reviewed. In essence, it has been concluded that ac- ceptable overall flotation recovery will only be obtained when efficient distri- bution of collector over all the component feed size fractions is ensured. The achievement of this goal is most likely to be obtained by feed classification and separate flotation of appropriate size fractions. The adoption of such a phil- osophy, however, imposes a number of process problems of both a chemical and an engineering nature. Some of these problems have been identified and possible solutions discussed. A case is emerging for the development of a new generation of flotation cells designed specifically for the flotation of classified coal and for the development of a series of novel re- agents which have the propensity to float middling particles.

Jan 1, 1984

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

By Adeloju S, McQuade CV, Riley SJ

Metal contamination of sediments can be an issue for minesites discharging water. Water sampling of receiving waters is frequently undertaken. Sampling and analysis of sediment is less common. The variability of receiving environments makes the formulation of a generic sediment sampling strategy virtually impossible. Each situation needs to be carefully assessed before sampling is undertaken. This paper outlines the approach taken for one such survey.The main factors that need to be considered in a survey of surficial sediments are sample representativeness and sample variability. A simple data set from one site within a regional survey is used to illustrate the importance of these factors. The metal content of sediment is shown to vary significantly over small spatial scales.The variability associated with the spatial distribution of samples within a site is shown to be the most significant source of variability in the study. This variability could bias the results of a study if not planned for in the sampling methodology. Taking multiple samples from within each site (sub-site samples) and combining the data gives a more representative indicator of overall conditions than a single sample. The optimum number of sub-site samples to be taken from each sampling site was found to be 15.It is shown that a composite of sub-site samples can give a good indication of the average site metal content, while considerably reducing the sample preparation and analysis effort.

Jan 1, 1998

Resource rent tax is a form of taxation or royalty, which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax (APT). The implications of the current form of Additional Profits Tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine, if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of Additional Profits Tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation. Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional Profits Tax is both time and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory. A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with Additional Profits Tax. The review includes examples based on the structure of Additional Profits Tax which is levied in Papua New Guinea.

Jan 1, 1997

At Bulong, the mineralised (>0.8 per cent nickel) ore exists within numerous lithologies, which can and do occur coincidently. It is very important to discriminate between the different host units for estimation purposes, stockpiling and scheduling. This allocation of host unit has relied upon visual interpretation by the geologist recording the information, which can be very subjective by its nature. By using quantified constraints, such as assayed magnesium oxide and iron, the subjectivity of describing the host material of nickel laterite ore is reduced. The constraints permit consistent identification of the various host units, which improves the confidence in the overall estimation and scheduling of the ore.

Jan 1, 2000

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is an energy efficient way of grinding and a number of operations have utilised this in the design of their comminution circuits. Owing to the large flow of slurry through the mill that results from operating this way the grates and pulp lifters have to be designed to cope. However, the literature has little or no information on how grate and pulp lifter size and design are related to their ability to remove slurry from the mill. Over the last few years the JKMRC has been researching this area and has developed relationships between grate/pulp lifter design and flowrate capacity. At the same time it has determined the major causes of pulp lifter inefficiency and a solution to preventing this inefficiency (the Twin Chamber Pulp Lifter). This paper describes the models that have been developed through this program and uses industrial scale data to illustrate their accuracy. Results from the industrial trials of the Twin Chamber Pulp Lifter are also presented.

Jan 1, 2000

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

By P Revell, A Jenkin

This paper presents an analysis of significant Australian-based R&D programs focussed on the minerals industry, which was commissioned by CRC ORE. The landscape analysis may assist organisations with R&D management issues including program creation, program/partner selection, portfolio management, and public policy settings. The dataset was collated early in 2020, and contains programs being conducted by or with Australian-based ‘Research Service Providers’ (RSPs), most notably Universities and CSIRO. It does not include R&D being conducted in-house by mining and METS companies, or by them with other organisations that are not RSP’s. The dataset contains 65 R&D programs, with total annual cash funding of $229m (70% from industry and 30% from government). The total funding compares unfavourably with the combined R&D expenditure of Australian universities and CSIRO of over $12b, and minerals industry export revenues of over $200b. The R&D landscape is analysed by program numbers and funding, technical domain, geography, and funding source. Areas of relative strength are noted in ‘mineral processing’, CSIRO Minerals, and the CRC program. Areas of relative weakness are noted in ‘bulk materials handling and logistics’, ‘tailings and waste management’, and ‘social and community’. The field of preconcentration is noted as a current area of R&D strength, but it is under significant threat with the impending completion of CRC ORE. The overall R&D landscape is characterised by a majority of small-scale programs, low levels of industry coordination, a low focus on step-change innovation, and total funding lower than should be expected for such a large critical industry. It is hoped that key stakeholders in the Australian minerals industry, particularly governments, and mining and METS companies, reflect on the analysis and act to address holistic weaknesses.

Nov 10, 2020

By C J. McKenzie, D F. S Natusch

The lignite deposits of Southland and Central Otago are a potentially significant energy resource for New Zealand. Current estimates put the technically mineable lignite reserves at 5.3 billion tonnes, which is more than ten times the energy content of the Maui gas field. Thus, the strategic importance of the lignite as a basis for maintaining current levels of self-sufficiency in transport fuels, or as a possible feedstock for electricity generation, deserves full investigation. The full extent of the lignite deposits was only recently established as the result of a scout drilling programme undertaken between 1976 and 1979 by the Mines Division of the Ministry of Energy, and from companion studies conducted by the New Zealand Geological Survey. These discoveries of large quantities of lignite coupled, at the time, with rising oil prices, raised the prospect of their development for production of transport fuels.

Jan 1, 1983

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024

By M Stewart, J Petrie, L Basson

This paper explores tools which have the potential to promote and assess the formation of partnerships between the minerals and energy industries to enhance the economic, environmentally responsible and socially acceptable use of energy. There is a need to look at energy provision and energy services in an integrated manner with key drivers for economic development û both locally and regionally. The minerals sector will remain highly significant to regional economic development in a number of globally significant regions in the medium term. Furthermore, mining, minerals and metalsÆ projects are both consumers and, in some cases (potential), generators of large amounts of energy (electricity included). It is therefore appropriate to focus on the promotion of partnerships between energy providers and the minerals sector which seek to improve resource efficiency within the combined minerals/energy envelope, guided by the tenets of Sustainability.Whilst there has been considerable development of systems analysis tools in recent years to address this sort of æcomplex systemsÆ analysis (Life Cycle Management, Cleaner Production and Industrial Ecology arguments for example), there is no effective roadmap available to decision makers to guide the selection and exploitation of these tools in different contexts. Our previous work developed a Decision Support Framework (DSF) which provides some guidance here, but only within the context of coal-based power generation. The DSF employs the tools of Multi Criteria Decision Analysis (MCDA), within which trade-offs between competing objectives are explored in such a way that alternatives can be compared without necessarily reducing all the different cost and benefits to a common basis (eg a monetary basis). Even if the existing DSF is extended to include all aspects of supply-side management, it is still lacking the necessary tools to analyse energy providers as dynamic network partners within minerals projects (or indeed any resource or manufacturing sector). New models are required for this, which firstly, seek to characterise such network structures, and secondly, enable the application of the necessary analytic tools to exploit these partnerships and networks for optimal performance.This paper explores the development of such an integrated set of network analysis tools, and their relation to the DSF. Due consideration is given to the choice of the attributes needed to characterise partnership linkages and network integrity (eg security of supply of electricity), and the efficiency of material transformations within any node of the network (as a function of energy consumption), and the impact that this has on the viability of other linkages (eg due to reduced availability of raw materials). We discuss how these perspectives help shape the form of objectives to be considered by MCDA.

Jan 1, 2004

By P Dean, M Elmouttie

Radar monitors are now widely used in surface mining for monitoring slope deformations and predicting failure events. Their introduction has facilitated better management of risk associated with slope failure during mining and therefore protection of personnel and equipment. However, a wellrecognised problem is that radar monitors only measure deformation directed towards the detector (line-of-sight bias). This bias can lead to misinterpretation of deformation size, rate and failure mechanism, and therefore miscalculation of failure volume, which can significantly impact safety and productivity. This paper presents recently completed research and field trials into the feasibility of using low cost vision systems to mitigate this issue. It has been demonstrated that by integrating a computer vision system with an existing slope monitor, high precision tracking of features in the field of view can be performed. Combined with assumptions on the deformation characteristics, the true 3D deformation vector can be estimated. The applicability of using this technique for monitoring iron ore mine slopes is discussed.

Nov 8, 2021

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

By Stanojevic R, McGlinn PJ, Day RA, Levins DM

This paper reports the results of a number of studies that Ansto has carried out for mineral sands companies concerned about low-levels of naturally-occurring radioactivity in their products. Where measured levels of radioactivity have exceeded allowable levels, Ansto has used specialised techniques to identify the source and distribution of the radioactivity and investigated processing strategies to remove the Contamination.

Jan 1, 1993

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By R Yong, A McEwan, D G. Miljak, D Milinkovic, A Curtain, P J. Coghill, R Stefulj, B Lovric, G Roberts

The CSIRO has pioneered the development and use of certain classes of magnetic resonance (MR) for mining applications. The MR technique is a radio frequency-based spectroscopy that provides highly quantitative measurement of selected ore minerals. MR has many inherent advantages for bulk sensing in mining applications, including deep sensing penetration into most bulk ores with the use of non-contact sensors that are robust and tolerant of demanding mine conditions. The highly discriminating nature of the technique also provides the very desirable attribute of robust and simple calibration, that can often be performed prior to sensor installation. Rapid sensing (within seconds) at very low grade (few hundred ppm Cu) has been demonstrated, as well as sensing at high tonnage rate. Besides sorting applications, MR may also be applied to preconcentration applications involving very large volume sensing including: (i) haul truck sensing using portal arrangements, where truck destination assignment may be dynamically determined based on the truck grade, (ii) in-pit gantries used for loading trucks that may similarly be equipped with sensors for truck assignment and (iii) deep mine bench sensing, recently progressed through a CRC ORE project, where local bench grade is determined at the few-metre lateral scale and at depth prior to blasting, to aid selective blasting and ore extraction. MR sensor prototypes have been developed for each of these applications and have been tested in laboratory or limited field conditions. To inform the value proposition for truck or bench sensing, initial analysis of truck assignment improvement based on an analysis of in-situ mine bench grade has been performed for a porphyry style deposit. The prototype sensors, preliminary results and future technology development and objectives will be described.

Nov 10, 2020

By Hollis R. G, Tuppurainen J. M I

Improved control of non-ferrous sintering operations requires the on-line measurement of sinter quality. No on-line measure of sinter quality is currently available, however, previous work has shown that the raw mix chemistry and peak sintering temperature determine the mineral phases formed and hence the resulting Blast Furnace behaviour. Control of these factors should therefore lead to improved quality control. In this paper, the development of a simplified heat and mass balance model of the Sinter Plant at Mt Isa is described. The model used available plant data to calculate raw mix composition and a simplified reaction scheme to predict sinter composition. The extent of reaction is inferred from the flue gas analyses. Off-line testing of a dynamic version demonstrated that actual plant performance could be predicted with reasonable accuracy.

Jan 1, 1989

By Middlebrook PD

The problems of education and research in the extractive metallurgy area are being tackled by the University of Melbourne through activities centring on the Department of Chemical Engineering. The establishment of the G.K. Williams Laboratory and the enhance- ment of the teaching of material relevant to extractive metallurgy in the Chemical Engineering course aim-at providing graduates and experienced researchers for the industry and at providing a strong research group carrying out industrially significant research in the area of pyrometallurgy.

Jan 1, 1986