Search Documents

King Island is situated at the western approach of Bass Strait and approximately mid way between Victoria and Tasmania. The scheelite orebodies lie within the south east of the island. Ore bearing horizons from 10 m to 40 m thick occur in south and east dipping stratiform deposits. The orebodies occur in skarn formed by contact metasomatic replacement of carbonate rocks by granite intrusives. The scheelite is deposited as fine disseminated grains in and along the margins of andradite garnets in the skarn. King Island Scheelite operates two under- ground mines from which 350 000 tonnes per year are obtained. The Dolphin mine produces almost two-thirds of the total. See Figure 1. The Dolphin orebody lies beneath the sea and an area of reclamation. The orebody is inter- sected by zones of major dislocation. A chequerboard post pillar cut and fill stoping system has been chosen to provide the necessary support to the hanging wall. Because the stability of the pillars is critical to the economic welfare of the mine, considerable attention is given to the reduction of overbreak.

Jan 1, 1977

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By Muir D

A review of the various methods of degrad- ing cyanide either from gold processing liquors or electroplating baths is presented with some discussion on their relative merits or problems. Whilst alkaline chlorination is common practice in many U.S. and Canadian plants it poses particular problems for certain plants. Alter- native methods include electrolysis, hydrolysis and air oxidation with activated carbon as catalyst which are also integral steps in the carbon-in-pulp process. A basic study of the degradation of cyanide ion has been carried out therefore to determine the effect of temperature, oxygen and carbon. It is shown that carbon is an excellent catalyst for degradation by air and likely to lead to higher losses of cyanide in a C.I.L. circuit. Degradation by hydrolysis is important at high temperatures and high pH such as employed in the Pressure Zadra or Anglo elution processes. Carbon catalysed degradation of cyanide by oxygen in effluent streams may be an environmentally acceptable alternative to conventional chlorine degradation.

Jan 1, 1987

By Browning E. J

The application of conventional dust control systems in British Coal mines has considerably reduced the incidence of pneumoconiosis. A number of new techniques have been developed involving extraction close to the cutting heads of mining machines which will be capable of controlling airborne dust with the greater intensity of production necessary in the present economic climate.

Jan 1, 1988

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

The last decade has seen a dramatic change in the. size and complexity of mining and mineral processing projects in Austral- asia. Major projects of today are vastly different from major projects of the 19.50's. This change has in turn resulted in a change in the role-of consultants whose contributions have been increasingly in the provision of specialist services and less in the form of overall project design and construction supervision. It is anticipated that, the specialist function will continue to represent the principle mode for consultant participation in major, projects. However, by means' of international affiliation, the development of comprehensive engineering and project management capabilities and possibly as a result of Government intervention, it is expected ,that local consultants will assume an increasing degree of participation in.the overall project design and supervision Function.

Jan 1, 1975

The Japanese Government promulgated the æLaw Concerning Special Measures Against DioxinsÆ on 16 July 1999 and it was enforced on 15 January 2000. This is a unique law specialised to protect the environment by the control of dioxin emissions from waste incinerators and several industrial processes. In this law, a few metallurgical processes other than waste incinerators are designated as æspecified facilitiesÆ emitting certain dioxins. Thus, emission standards for dioxins to the air were set for electric arc furnaces (EAF) for steelmaking, iron ore sintering, zinc recovery from EAF dust and aluminum recycle processes. In this paper, the inventory of dioxin emissions for Japan and the recent research and development to reduce emissions from those processes are introduced. Further, some details on the formation mechanism of dioxins and future subjects for effective control of their emissions are discussed.

Jan 1, 2002

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995

By Totterdell JM

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid- Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian- Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

Copper heap leaching involves both the simultaneous and sequential leaching of very large tonnages of ore over long periods of time. It is not unusual to be leaching three or four million tonnes over periods of 12 to 18 months. As a consequenc

Jan 1, 1998

Although the diesel engine is normally considered a tried and proven power source, many new and exciting diesel design concepts are being evaluated in engine development laboratories around the world. Three such programs currently underway at Cummins Engine Company are discussed. The turbocompound engine converts into power exhaust heat energy which is normally wasted. It does this by incorporating after the turbocharger a low pressure gas turbine which is gear driven to the crankshaft. The adiabatic engine has no conventional cooling system. It converts into useful power most of the heat energy normally rejected to the coolant. The series boost turbocharged engine uses seperate low and high pressure turbochargers to increase engine output and improve transient performance. These design concepts make possible increases in diesel engine thermal efficiency from the current 33 to 38 per cent range to the 50 percent range.

Jan 1, 1982

By Krokhmai VS, Sayko OP

The paper summarises the theoretical and experimental studies which led to the development of new industrial equipment designed to recover liberated gold from placer gravity concentrates. The new technology is based on environmentally clean magnetic methods, which avoids use of mercury in the production process and obtains higher gold recoveries compared to the amalgamation technique, and which can reach 98.6 - 99.5 per cent. The complex of equipment thus developed is now commercially used at nine Russian gold mining operations. Six more such complexes are due to come on stream in 1993, some of them outside the CIS. The new technology appears to hold much promise for the recovery of precious stones (diamonds, rubies etc) semi-precious stones (pyropes, chrysolites etc) and also artificial diamonds, for which case there are encouraging laboratory results.

Jan 1, 1993

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

By R van Berkel

Regional synergies concern the capture, recovery and reuse of by-products, water and energy between industrial operations in close proximity. The Centre for Sustainable Resource Processing (CSRP) undertakes applied research to further advance regional synergies in the Kwinana Industrial Area in Western Australia in order to achieve greater efficiencies in water, energy and materials consumption and reduction in waste and emission generation. The Kwinana Industries Council (KIC) and its member organisations recognise water consumption and disposal as key environmental issues. Some 30 companies in Kwinana consume a total of more than 35 000 ML/yr of fresh water. Over the past years significant progress has been made towards the reduction of water consumption and improvements in effluent disposal. As part of the CSRP Kwinana Synergies Project, water balances for the ten major water consuming companies have been completed, including workshop sessions with company staff on water synergy opportunities. This work resulted in a set of synergy opportunities which are currently being pursued. In parallel to the Kwinana project, the CSRP has commissioned a supporting project that delivers a toolkit to guide a more targeted and less resource intensive way to identify feasible water synergy opportunities. One of these tools focuses specifically on water, and takes count of input and output water flows within a given industrial area to deliver listings of prioritised water synergy opportunities. This paper discusses the water mapping and workshop approach taken in Kwinana and its outcomes, which are to identify and evaluate water synergy opportunities. The results from the trial application of the developed Regional Eco-Efficiency Opportunity Assessment Toolkit are also presented.

Jan 1, 2006

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

This paper reviews the role of fill in mining including consolidated fill both histor- ically and currently as determined by a recent survey of the Fill Subcommittee of the Canadian Advisory Committee on Rock Mechanics (CACRM). It covers the application of fill in modern min- ing methods including mechanized cut and fill, undercut and fill, post pillar cut and fill and longhole pillar recovery between stabilized fill. An automated fill preparation plant and recent developments in rotary drilling of hydraulic fill conducting holes are described briefly. The paper also summarizes the findings of some of the important laboratory and field work carried out on the behaviour of fill in Canada, the United States and Australia and again draws on current information obtained from the Fill Subcommittee of the CACRM. Space limitations and unavailability of suitable material prohi- bit the summary of similar information from other countries.

Jan 1, 1973

By Grinenko VA

Mineralogical, chemical, and isotopic data have been obtained for samples from 11 volcanoes and 4 kortlandite intrusives on Kamchatka.Similarities and differences in ore-bearing and barren intrusives are discussed. Differences in sulphide mineralization and sulphur isotope compositions of intrusives are explained in terms of the "auto-sulphurization" hypothesis which involves the redox conditions of the host rocks. possible role for carbon in nickle sulphide ore formation is also considered.

Jan 1, 1990