Search Documents

By H S. Shin, H Jin, B H. Ryu, J Lee

Prospecting ice on the Moon necessitates drilling systems to obtain subsurface samples and measure the composition of ice deposits. Landers and rovers equipped with drilling equipment are essential for analysing ice and subsurface resources located at the Moon’s poles. These devices must be small, lightweight, low-power, highly efficient, and high-performance units to function properly in the extreme conditions of the lunar environment. Researchers have developed a prototype drilling apparatus capable of operating in atmospheric and cold environments. A newly developed drilling system in Korea, capable of performing not only sampling but also subsurface investigation, is introduced.

Sep 1, 2024

Poor ground conditions associated with historical workings have presented significant challenges to the drilling of production downholes at the Sons of Gwalia Mine. The combination of foam and polymer drilling, the use of Aquacrete to drill through voids and the practice of lining completed holes has allowed downholes to be effectively drilled and blasted in delaminated ground.

Jan 1, 2002

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By S Kodate, Ö Aydan, Y Suda, J Tomiyama

Fracture zones are commonly found in the Earth’s crust. These zones may cause very severe engineering problems. Therefore, the formation and the assessment of the mechanical characteristics of these zones is of great concern for rock engineers. A new double shearing jig was used to study the formation of shear zones in rock under static and impact loading conditions using the device developed by the authors. A series of experiments were undertaken to investigate formation on the formation and characteristics of fracture zones in laboratory. Although actual fracture zones are more complicated, various tests give some insight view of the formation of fracture zones as well as some information on their mechanical behaviour under both dynamic conditions and static conditions. The authors report the outcomes of these experiments and discuss their implications in practice.

Nov 29, 2022

The original design of the Bougainville Copper Limited (BCL) concentrator took cognisance of the constraints imposed by the topography, the need to minimise capital cost, and the need to allow for plant expansion which, it was known, would be necessary to maintain copper and gold production as head grades declined.At the same time as spare slots have been taken up with additional equipment, technological innovations have been embraced whenever there appeared to be a chance of improving the productivity ofexisting equipment, or replacing it with a more efficient alternative.There are many examples of this in the BCL concentrator in the areas of process control, process design, instrumentation, materials handling, equipment design and wear part technology.Current process developments also pursue the latest technology. The development of the Omnicone crusher, flotation control, tailings water reclamation, and the variable speed gearless drive on the No. 13 mill are prime examples.

Jan 1, 1986

By J Krnmmelbein, T Raab

In Lusatia, lignite mining causes major disturbances on the landscape scale. Reclamation procedures are applied to recover the reconstructed landscape for different land use options. In this study we investigate soil physical properties of an agricultural reclamation/recultivation site directly after site restoration and the development of selected parameters within the first years after site restoration depending on varying recultivation strategies.The sandy substrates used for recultivation stem from depths of several meters. They are unstructured, free of recent organic matter and have high contents of calcium carbonate. During reconstruction and most of all during surface levelling with heavy crawlers, the substrate?undergoes high mechanical stresses. This leads to partly severe soil or substrate compaction, depending amongst others on substrate water content and mechanical stresses during site construction. We investigate the effect of different organic soil amendments, different crop rotations and partly subsoiling on the development of soil structure. We compare results of laboratory measurements directly after site construction before any reclamation measures had been applied to results we gained after three and four years of recultivation. The results show that after the earthworks are completed, the site is strongly heterogeneous in relation to mechanical stability, permeability for air and water, pore volume and bulk density. The results after three and four years show that the heterogeneity of soil physical parameters decreases. The selection of suitable crop rotations superimposes the affects of other reclamation measures, eg varying organic fertilisers or deep loosening.CITATION:Krnmmelbein, J and Raab, T, 2012. Reclaimed lignite mining areas A73 in Lusatia - Development of soil physical parameters of an agricultural site within the first years after site reconstruction, in Proceedings Life-of-Mine 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By H Bartosiewi, M Kuruppu, F Mashiri

Wire ropes are one of the most heavily used components in a dragline. They are subjected to harsh conditions during the regular usage of a dragline in a mining operation. Hoist ropes are subjected to fatigue due to the cyclic nature of load handling as well as due to rope bending over the sheaves and the drum under load. This leads to wire breaks due to fatigue. Accumulation of a number of wire breaks close to each other can have a detrimental effect on the rope. Furthermore, to allow for the increasing demand for higher load capacity coupled with the inconvenience of having very large ropes, the factor of safety is often compromised, which increases the wear rate. Drag ropes are also subjected to heavy loads. More importantly, they are allowed to drag along the rough mine surface subjecting them to external physical abrasion. This makes the life of drag ropes one of the lowest among those used in a dragline. Suspension and IBS ropes are relatively uniformly loaded during their regular usage although they need to withstand dynamic load cycles as well as bending. Hence they tend to last for a number of years on average. The paper analyses the wear types and their severity of each of these rope applications, and suggests methods to determine rope wear rates and the resulting rope life. The paper further gives suggestions for good operating and maintenance practice that can extend the rope life and help reduce the large expenditure associated with every major rope change in a dragline.

Jan 1, 2005

By S C. Bhowmik, R Gupta

This paper presents the ventilation problem faced by Jaduguda uranium mine, operated up to a depth of 905 m. The first two stages of the mine workings are up to 555 m, which are nearly exhausted. The third stage of the mine is from 555 m to 905 m and presently most of the stopping and development activities of the mine are carried out in the third stage. The total available intake quantity in the third stage was only 21 m3/s. As a result, the mine was facing a radiation hazard. The different instruments and the methods used for monitoring of radiation levels are also presented in the paper. It was observed that the average individual effective dose (external + internal) of radiation workers in Jaduguda mine increased from 6.93 mSv/y in 1995 to 9.5 mSv/y in 2001 and during this period the average individual effective dose of mine workers of the world was less than 5 mSv/y. Keeping this problem in view, a detailed ventilation investigation has been carried out in this mine. Initially the requirements of intake air quantity have been assessed by carrying out field investigation in different stopes and it was found that the third stage workings require nearly 100 m3/s. A detailed ventilation survey has been carried out in the total ventilation network and a basic ventilation model of the mine has been prepared. Different alternative schemes for effectively ventilating the third stage workings of the mine were simulated and a set of recommendations were made for implementation. The recommendations were partially implemented in 2002. As a result the total intake quantity to third stage workings increased to nearly 70 m3/s and the average individual effective dose (internal + external) of mine workers came down from 9.5 mSv/y in 2001 to 6.65 mSv/y and 6.60 mSv/y in 2002 and 2003 respectively. The implementation of remaining recommendations is in progress. Finally, a mathematical model has been formulated from the first principle for predicting air quantity requirements in cut and fill stopes in uranium mines and this model is being validated for further use.

Jan 1, 2005

By D Baas, Y Atasoy

With increased pressure for companies to cut costs during design of new mineral processing plants, overall plant design has changed over the last decade with less design for feed blending and less installed surge capacity. This has changed the operability of new mineral processing plants, where disturbances due to variable ore types have resulted in the evolution of new control techniques. These techniques are necessary to maintain stability and optimise the performance of these new plants. This paper describes the benefit of applying these new control techniques in a new mineral processing plant in Australia utilising RockwellÆs ControlLogix system architecture.

Jan 1, 2008

Many of the large refrigeration plants used in, the cooling systems on deep South African gold mines are situated on surface where they are exposed to seasonally and diurnally varying climatic conditions, and to a diurnally varying demand for cooling made by the mine. It has been traditional to accommodate the seasonal variation in climate by manual control applied to the plants at appropriate times of the year, and the plants have normally been specified to conform passively to the diurnal variations. This paper introduces new strategies for the active automatic control of the plants on a diurnal cycle, and shows that attractive benefits in energy and chilled water resource management can be accrued through the use of these strategies. The results have been derived through the modelling and simulation of a representative refrigeration plant.

Jan 1, 1985

By Schneider CL

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance, and it is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require a very detailed knowledge of the complex interactions between the fracture patterns and the mineralogical ore texture when brittle particles are subject to impact fracture. Most of the liberation models that have been developed to date apply only to batch comminution processes and under these conditions the liberation problem can be studied in isolation. When the comminution is continuous and forms a unit operation in a flowsheet that includes classification and separation operations, the situation is very different, and then the liberation of the minerals must be described when single particles of known mineralogical composition are fractured. Important industrial examples are conventional milling circuits closed by hydrocyclone and regrind mills in flotation plants. This paper presents an efficient computational algorithm for the calculation of the liberation spectrum produced by continuous milling operations. The algorithm relies heavily on the detailed internal structure of the Andrews-Mika diagram. The modifications that are required to make this diagram apply to practical ore minerals, and the internal structure of this diagram can be established using single-particle fracture on mono-size, mono-grade material but suitable liberation models are essential to interpret the data in terms of the cross transfer coefficients required for the population balance procedure. Models proposed by Leroux (1992) and King (1990) are compared to experimental data.

Jan 1, 1993

By Terrill JE, Fergusson LJ

In the last decade of precious metal exploration, several important gold discoveries have conclusively demonstrated that epithermal gold deposits formed in what were once active geothermal areas. A significant deposit in this category is the Lihir Island discovery in the Tabar-Ferri volcanic island arc off the coast of New Ireland, Papua New Guinea. Within that arc are the Feni Islands where exploration by Esso PNG Inc. and City Resources Ltd. has been carried out since early 1984. On Ambitle Island in the Feni Group, an epithermal gold prospect located within a young caldera has been tested by diamond drilling. The drillholes intersected a boiling zone at depth beneath acid altered 'cap' rocks. The zone is 30-60 metres thick and comprises hydraulically fractured and mineralised lavas with gold grades of 1-7 g/t. The prospect is still an active geothermal area with current boiling in the zone tested. As on Lihir, the recent epithermal alteration and mineralisation overprints a relict prophyry system. On Ambitle and the adjacent Babase Island several other, cooler exciting gold prospects are currently being tested.

Jan 1, 1987

By T Hayward, G Lane, M Phillips

In December 2004 Phu Bia Mining Ltd commissioned Ausenco International Limited to conduct a feasibility study for its Phu Kham copper-gold project located in Laos. The feasibility study for a mining and processing operation treating 12 Mtpa of ore averaging 0.56 per cent copper and 0.25 g/t gold to produce an anticipated annual average 200 000 t of concentrate containing 25 per cent copper was completed in early 2006. The plant design incorporates a single processing line and includes a gyratory crusher, overland conveyor, coarse ore stockpile, SAG and ball mill grinding circuit, flotation circuit including regrind and three stages of cleaning, concentrate dewatering and concentrate load-out facilities. The Phu Kham copper-gold mineralisation comprises two principal styles: stockwork-disseminated and banded-massive sulfide within skarn limits. Primary copper in both mineralisation styles occurs as chalcopyrite and secondary copper sulfide minerals. Skarn includes the copper and gold mineralisation contained in pyrite, silicate, magnetite and haematite skarns, and in quartz-pyrite altered sediments. Both the stockwork-disseminated and banded-massive sulfide ores contain relatively high proportions of pyrite relative to the copper and gold mineralisation. Thus, the flotation metallurgy of the Phu Kham orebody is characterised by the need to reject a high proportion of the pyrite during differential flotation to yield a concentrate grade of approximately 25 per cent copper. The rejection of pyrite is accompanied by the rejection of some copper and gold and can result in modest metallurgical recovery. Consequently, the greater the pyrite content, the lower the expected copper and gold recoveries. The relative pyrite content is expressed on the basis of sulfur:copper ratio. For Phu Kham ores, the sulfur:copper ratios are in the range eight to 14 on a blended annual basis, but can be greater than 20 in the skarn components. Higher grades of copper and gold are also present in the skarn mineralisation. The design concepts for the concentrator were influenced by the need to provide a low capital cost approach for the project due to the relatively low grade of the ore and the modest metallurgical recovery. The concepts used to minimise capital cost whilst retaining operating and maintenance flexibility are discussed, together with the metallurgical challenges imposed by the high pyrite mineralisation.

Jan 1, 2007

By L Reynolds, N Whetter, S C. Cox

The Reefton Goldfield has had the largest hard-rock gold production (64 t Au) on the West Coast of the South Island of New Zealand, and is currently under renewed development by Oceana Gold. The gold predominantly occurs in variably sheared quartz veins that are associated with zones of tighter, shorter wavelength folds in the host Greenland Group metasediments. The quartz veins typically occur as a series of plunging shoots that align with specific fold limbs or fold hinge zones. Shear zones containing disseminated mineralisation and quartz veins have thickness variations that relate to the angular relationship between the shear and host-rock bedding. Exploration strategies and targeting can be developed around both types of structural control.

Jan 1, 2005

Pisolitic iron ores (also known as channel iron deposits) are an important resource of medium-grade iron ore in the Hamersley Province of Western Australia. They are a special case of transported pisolitic ferricrust, differing from normal transported ferricrust only in the exceptionally high iron and low alumina content. The pisoids typically range up to 5 mm in diameter with abundant particles of ferruginised fossil wood up to 15 mm in maximum diameter preserved in the sediment. Field observations indicate that pisoliths are commonly initiated by the action of raindrops on iron-rich soil. Pisolites form by the impact of raindrops forming coated beads of ferruginous soil, which after dehydration obtain additional coatings during successive showers. Thick deposits of pisolite that are transported and deposited primarily by sheetwash form in the distal regions of the pediment. A size range limited to particles that may be transported by extremely shallow water characterises the abundant fossil wood fragments. The absence of fine sedimentary layering in pisolitic iron ores is explained by the action of soil-forming processes after deposition, while the major coarse bedding features derive from successive erosional and depositional events in the evolution of the pediment. They are not deposited in channels by rivers which, in arid to semi-arid conditions, typically deposit quartz sands and gravels with characteristic point bars and current bedding, abundant ferruginous granules, but rarely pisoids. However, they may fill abandoned river channels.

Jan 1, 2007

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998