Search Documents

Knowledge of the crystal chemistry of carbonate apatites is very important for the development of the concept of biomineralisation and the creation of a scientific base for new biocompatible materials for medical purposes. The present work is devoted to research results on various synthetic and biological carbonate apatites obtained at Saint Petersburg University over many years. All-important problems will be considered such as the location of CO32- ions in the apatite structure, the ionic substitutions in various biological apatites and the development of synthesis methods for their analogues. Syntheses of apatites were realised by precipitation methods and under hydrothermal conditions (from solid compounds and by calcite treatment). Biological samples used in this study were physiogenic and pathogenic apatites formed in the human organism, eg in teeth and in renal and salivary stones and dental calculi as well as apatites from fossils of different taxonomic families (brachiopods, conodonts, fishes, reptiles, mammal) with different geological ages and burial conditions. The study of the crystal chemistry of carbonate apatites has been carried out by powder (including high-temperature measurements) and single-crystal X-ray diffraction methods, IR-spectroscopy, thermal analysis and various chemical analytical techniques.

Jan 1, 2008

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By M I. Pownceby, S Bhargava, F Charalambous, S McMaster, R Ram, J Tardio

"A key component of any geometallurgical investigation involves being able to predict element or mineral recoveries from simplified input data such as bulk chemistry and/or mineralogy. This relies on the metallurgist having access to accurate information regarding the chemistry of the ore and gangue minerals as well as the likely impact on processing/extraction caused by the impurities (present either as gangue or as substitutional impurities). In this study the chemical properties of two commercially important uranium minerals, brannerite (U4+Ti2O6), and uraninite (U4+O2), were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). Significant levels of impurities were present in both samples with the uranium minerals deviating significantly from their ideal chemical formulae. Differences in chemistry were due to: cationic substitution decay of the uranium isotopes into radiogenic lead and other daughter products mixed uranium oxidation states post-depositional alteration.As well, the brannerite sample showed evidence of significant radiation-induced metamictisation. Leach tests to measure the ease of extraction of uranium from both samples were conducted over a wide range of conditions (temperature, acid concentration and oxidant concentration). For uraninite, the lower U dissolution rates observed in the natural sample compared to a synthetic UO2 sample were directly attributed to the presence of impurities. For brannerite, significant metamictisation of the natural sample led to enhanced U extraction rates compared to a heat treated fully crystalline sample. This study highlights the importance of detailed mineralogical characterisation studies in any uranium process mineralogy investigation as the compositional, textural and microstructural aspects of the main uranium phases present will likely play an important role in any process to extract uranium.CITATION:Ram, R, Charalambous, F, McMaster, S, Pownceby, M I, Tardio, J and Bhargava, S, 2013. Chemical and microstructural characterisation studies on naturally occurring uranium minerals - implications for processing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 325-334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By G York

South African gold reserves extend to great depths. However, strategies for the mining of such deposits have changed only slightly over the past number of years. Regional support at depth is currently provided by rock pillars and backfill. Many problems have been experienced with these regional support practices at deeper levels. In this paper several alternative forms of regional support are described which include the use of concrete, the use of back area caving and confinement to strengthen pillars. These new concepts are supported by numerical and laboratory modelling and in situ results.

Jan 1, 1998

By C Mason, A Littleboy

This paper presents the results of a large scale survey of The Australasian Institute for Mining and Metallurgy (AusIMM) membership. This survey aimed to understand and define the key issues and drivers that AusIMM members perceived would shape the development of the Australian minerals industry over the next 20 - 30 years. Nine hundred and fifty-nine participants rated the importance of 11 issues and six drivers (generated from interviews with AusIMM members), and 236 of these participants also provided qualitative descriptions of the future. Issues were defined as problems or opportunities for the minerals industry that may be controlled or influenced by the industry, while drivers were defined as those factors that will influence the direction of the industry that are not within the control of the industry. The quantitative data revealed that the top four issues, in order of their perceived importance to the Australian minerals industry, were: investment in exploration, workforce, health and safety, and innovation. The top three drivers in order of their perceived importance, were: economics of mining, global context and Australian society. While the top four issues were largely consistent across professional groups examined, metallurgy and mineral processing professionals rated water inputs and energy inputs significantly higher than the other professional groups. For the list of drivers, there was strong agreement regarding their ranked order of importance across the professional groups examined. Within the qualitative data, however, a single issue (technology) and a single driver (economics of mining) dominated participantsÆ descriptions of the future. These findings provide important input into a broader program of scenario development for the Australian minerals industry being undertaken by CSIRO and its partners. The results of this study demonstrate the importance of using a mixed methodology in generating these inputs to understand more fully how important stakeholders view the future and the factors that will shape it. The results of this study are also discussed with respect to the role that CSIRO may play in facilitating the exploration of uncertainty around the future of the Australian minerals industry.

Jan 1, 2009

A study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fel_xS, CuFeS2, Cu2S) has been conducted using a mesophilic strain of T. 6ejtAooLcdcth4. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate ion has been monitored. Partially oxidised sulphide substrates have been characterised at regular time intervals by X-ray diffraction methods and extra-cellular organic compounds reporting into leach solution have been identified by'thin layer chromatography. The results indicate that the S¦/SO4 2 partitioning of the sulphide substrates is independent of cell inoculum size and initial pulp density and varies with solution pH, Eh, leaching time and mineralogical properties of the individual sulphide minerals. The signifi- cance of results for applications in selective flotation, coal desulphurisation and agglomera- tion has been outlined.

Jan 1, 1984

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By A R. Cruden, M S. Egglseder

The formation of banded iron formation (BIF)-hosted high-grade iron ore deposits in the Hamersley Province, Australia has been debated for decades. Although a structural control on their formation is widely accepted, only the roles of large-scale structures (ie faults and folds) formed by brittle and ductile deformation have been considered to date. However, the deformation of multilayered sequences in the Hamersley Province (ie the Mount Bruce Supergroup), with their contrasting rheological behaviours, creates challenges for understanding the complex structural framework at regional to deposit scales, including the significance for mineralisation and orebody location.Our approach to understanding these complex relationships is based on an established principle of structural geology, which is to extrapolate microscale structures to deposit-scale structures and vice versa, supported by state-of-the-art 3D modelling techniques. Complexly deformed hand samples associated with the Mount Tom Price iron ore deposit (Hamersley Province, operated by Rio Tinto Ltd) have been analysed and visualised with 3D explicit (Move™, Midland Valley Ltd) and implicit modelling software packages (Leapfrog™, AranzGeo Ltd) and supported by microstructural investigations (optical and X-ray microscopy) and fieldwork.Our study shows that the deformation of BIFs in the central Hamersley Province is controlled by microscale chemical processes (ie dissolution precipitation creep) due to rheological differences between iron oxide and chert layers, contrasting fluid flow properties and layer thickness variations. These processes account for the removal of vast amounts of silica, its transportation by diffusion in the presence of a fluid and reprecipitation at low-pressure sites. Consequently, this structural framework was used by different upgrading fluids to form iron orebodies.CITATION:Egglseder, M S and Cruden, A R, 2015. Evolution of a structural framework for high-grade iron ore deposits, in Proceedings Iron Ore 2015, pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J J. Eksteen

"In the platinum group metals (PGM) industry, smelters are often perceived as ‘black boxes’ that have to process concentrates of variable mineralogy and originating from multiple mines operating along strike or downdip from each other in the same geographical region, as is the case in the Western Bushveld of South Africa. However, PGM smelter complexes are much more sensitive to concentrate blend variation than most metallurgists or geologists would anticipate.This paper will review the impact of concentrate blends deriving from a number of concentrators processing ores from the Bushveld Igneous Complex (BIC) on smelting and converting behaviour and the constraints they impose upon smelter operation. Significant variation in behaviour is not only noted between the main mineralisation types, namely the Merensky and Upper Group 2 (UG2) reefs, but also within a given reef type. Due to the way PGMs are mineralised and finely disseminated, concentrators have to grind concentrates ultra-fine to liberate the PGMs and provide a sufficiently high-grade concentrate for smelting.The chemistry and mineralogy of the concentrates vary with the type of mine (open pit versus underground), the reef type and varies along strike; this variation impacts numerous key smelter parameters such as the base metals content, the matte fall, the converter aisle capacity, sulfur dioxide gas production, furnace matte and slag temperatures, and the accumulation of high smelting chromite-spinel minerals that has led to significant smelter upset conditions such as catastrophic furnace hearth and sidewall failures.Due to the production intensity of smelting, ie its high rate of processing per unit volume, smelters have been found to be far more sensitive to rapid variation in concentrate properties, highlighting the need for adequate blend control.CITATION:Eksteen, J J, 2016. Impact of Mineralogical Variation on the Smelting of Cu-Ni-PGM Concentrates, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Manlapig E. V

ABSTRACT- I Results are given for a series of tests in which a 300 mm pilot-scale Jameson cell has been used in copper recleaner flotation, and for the flotation of a lead rougher feed. the results indicate that the production rate of solids, at the same superficial air velocity Jg, is higher than in conventional columns. Thus in the copper recleaner application, the pulling rate reached 14 gm/cm2/min compared with between two and three for an operating column, while in the lead cleaner application the comparable figures were 12 - 14 gm/cm2/min for the Jameson cell vs 8 - 9 gm/cm2/min for a test column. A froth crowder was used to increase the air superficial velocity Jg in the Jameson cell in the copper recleaner, while holding the collection mechanism and pulp feed rates constant. The recovery increased from 50 per cent to over 90 per cent, suggesting that recovery is controlled mainly by the froth conditions, rather than the particle-bubble interactions in the Downcomer.

Jan 1, 1991

Subsurface development requires some geotechnical conditions and challenges. Most of then are related to the compatibility between tunnelling system and surrounded ground conditions, and design criteria. Design criteria usually involve lining pressure and ground control of displacements. In order to fulfil these requirements, geotechnical parameters have to be obtained as well as construction aspects have to be taken into account for predicting the tunnel behaviour. The Brasilia Metro is presented as a case history illustrating the geotechnical conditions and challenges for its implementation. It is 42 km long, including tunnels excavated in collapsible porous soils by the New Austrian Tunnelling Method. The Brasilia porous clay presents some characteristics, which may lead to large deformations due to structural collapse. Empirical methods were calibrated for collapsible porous soils and then applied to predict tunnelling-induced settlements. Settlements due to soil structural collapse modify completely the expected settlement profile, increasing their values from the tunnel crown to the ground surface. Consequently, surface settlement trough volumes were also greater than the ground losses around the tunnel. In this case history, structural collapse of porous soils played an important role and must have been taken into account to predict correctly the settlement trough and profile. Numerical simulation has shown that settlement magnitudes due to structural collapse are strongly dependent on the soil stiffness reduction after collapse and the extent of the collapsible zone.

Jan 1, 1999

The State of Western Australia has a land area of 2 525 000 km2, and is well endowed with minerals and petroleum products. In 1989 - 90 these products were valued at nearly A$10 500 million.

Jan 1, 1992

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

By J Manuel, A Trudu

Regulations on the emission of particulates from sinter plant stacks are becoming increasingly stringent and reducing these emissions by improving gas cleaning systems is a significant cost to the sinter plants. This paper describes an investigation into the emission of particulate matter from an iron ore sinter bed during the sintering of a Japanese Steel Mill (JSM) style ore blend in a 300 mm diameter pot grate test facility. Several techniques were trialled to determine a reliable method to sample the quantity of dust emitted and determine the mechanism of dust emission from the sinter bed. The nature of the dust was also examined using chemical and size analysis as well as optical and scanning electron microscopy. The paper discusses the techniques used to carry out the program as well as results on dust loading measured during sintering and the nature of the dust captured.

Jan 1, 2002

By A E. C Peres, J D. Donda

With the aim of producing a concentrate with silica content lower than 1.0 per cent SiO2, laboratory experiments were conducted using a sample of the final concentrate from the Samarco iron ore flotation plant (mechanical cells circuit). The sample contained 3.08 per cent SiO2. This sample was split in two size ranges: >105 ¦m and 2. The >105 ¦m fraction, representing 23.3 per cent of the initial mass, was re-ground to 100 per cent 2 content were obtained. Considering the mass proportions of the two size fractions, the calculated silica content of the combined concentrate was 0.68 per cent, which is considered satisfactory for the objective of this investigation. The major reasons for the higher (0.90 per cent) silica content of the concentrate from the coarse fraction are the presence of silicon in the lattice of goethite and the presence of residual silicious slimes in the pores of porous hematite.

Jan 1, 2005

By S W. Richards, J Buys

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Magmatic arcs are prime targets for porphyry- and epithermal-style mineral deposits, although settings within continental arcs and/or tectonically-thickened crust generally tend to be more prospective than intra-oceanic arcs in extensional settings. In this paper, we report new geochemical and geochronological data on igneous rocks of the Western Belt of the Vanuatu intra-oceanic arc. Dating of igneous hornblende (Ar-Ar) and zircon (U-Pb) from the igneous rocks place their formation in the late Eocene to Miocene. In most respects, these are typical arc igneous rocks. However, they contain inherited zircon grains with significant age populations at ca 2.8–2.5 Ga, 2.0–1.8 Ga, 1.75–1.5 Ga, 850–700 Ma, 530–430 Ma and 330–220 Ma. This inheritance signature is unlike anything recognised from the oceanic realm of the south-west Pacific, but, in general, does match the age of the major crustal blocks of the Australian continent. An exception is the significant proportion (~20 per cent) of zircons of Rodinia breakup age (~800 Ma), which previously has not been found in eastern Australia or the south-west Pacific.We propose that part of the Vanuatu arc basement comprises a ribbon of continental material rifted from northern Australia prior to, or during, the Cretaceous. The presence of ancient continental material within the Vanuatu island arc may help reconcile the relatively large thickness and low density of the crust of Vanuatu, and may enhance the prospects for significant porphyry and epithermal ore deposits in the region.CITATION:Spandler, C, Buys, J, Holm, R J and Richards, S W, 2015. Remnants of ancient Australia in Vanuatu – implications for south-west Pacific tectonics and mineralisation potential, in Proceedings PACRIM 2015 Congress, pp 183–188 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By Wilson AF

Gold-silver mineralization at Cracow and Ukalunda in Queensland comprise quartz-filled veins, fissures and breccia zones hosted by propylitically altered volcanics and epizonal intrusions which are strongly fractured. The terrestrial volcanic facies, structural setting, type of alteration and complex mineralogy suggest these deposits are of the epithermal type.The 180 depleted character of the wall-rocks is consistent with the involvement of meteoric waters in convective hydrothermal cells associated with the vulcanism. The Cracow quartzes have remarkably low 6180 values from -2.0 to -3.4 per mil typical. of meteoric hydrothermal systems at high latitude, consistent with the inferred position of Australia during the Permian. 6180 values for the Ukalunda quartzes exhibit a wide range from 5.1 to 14.9 per mil which reflect the mixing of magmatic and meteoric waters, and a steep geothermal gradient.Further stable isotope and geochemical studies are in progress to establish the scale and morphology of the zones of anomalous 6180 and mineralogy in the wallrocks which constitute significant exploration targets.

Jan 1, 1984

By Cocks T

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

ABSTRACT' The first references to gold in New Guinea were by the Portuguese in 1525. The first significant discovery and gold rush was on Sudest Island in 1888 and was a natural extension of the rush that surged up Australia's eastern coast and ended at cook- town. Prospectors made a series of minor discoveries in coastal regions before the first large discovery at Wau/Edie Creek/Bulolo in 1925. Major post war gold discoveries were made at Bougainville, Frieda River, Porgera and Ok Tedi. On Misima Island a large bulk low grade deposit has been recognised surrounding old gold workings. Gold exploration has increased drama- tically since the lifting of a 3 year moritorium on new exploration areas in Noverrber 1982. A new bulk low grade gold discovery has been made on Lihir Island, north of Bougainville and a number of other promising areas are being drilled. Gold production is also expanding dramatically from current levels of 600,000 ounces to an anticipated 1.3 million ounces in 1985 with the opening of Ok Tedi. Other potential developments are likely to increase output above 2 million ounces by 1990. Papua New Guinea's world ranking as a producer is likely to move from 9th to 7th in 1985 reflecting the favourable geological potential, stable political environment and attractive development terms offered by the Government.

Jan 1, 1984