Search Documents

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

This paper discusses a number of examples of how environmental factors have been incorporated into the water management aspects of mining projects. One example is the Kingston Lignite Project in the South-East of South Australia where the most significant environmental issue was considered to be the effect of drawdown from mine dewatering and depressurization upon the use of groundwater. By proposing an alternative mining method - the use of floating dredges rather than a two-pass dragline method - drawdown effects would no longer be a concern. A second example is the Pine Creek Gold Mine in the Northern Territory. In this case the principal area of interest from an environmental viewpoint was water management - in particular effluent disposal, contaminated seepage from overburden and tailings, and project water supply. Through an integrated approach to the management of wastes and water the potential for water quality impairment was significantly reduced and external water supply requirements were also significantly reduced.

Jan 1, 1987

By Martinick WG

In July 1986, Cable Sands (W.A.) Pty Ltd commenced mining for mineral sands at Minninup, approximately 16 km south of Bunbury, Western Australia.The area being mined is from the heel of the foredune to the rear of the hind-dune. The vegetation is mostly native vegetation with some old degraded pasture.The mining operation will be by suction cutter dredge, with continuous dredging, mineral separation and re-depositing of the sand.

Jan 1, 1986

By Cox A

A key concern both in public perceptions of the environmental performance of the mining industry and in the development of policy relating to mining activities is the state in which the areas may be left at the completion of mining operations. There is, in effect, concern that the transient economic benefits of mining are enjoyed by the few, while the 'scars' may remain for all. While the techniques of mine rehabilitation have improved rapidly in recent years, an important set of economic issues has generally been neglected.In this paper, the economic and policy aspects of mine rehabilitation are examined. The key issue addressed is how to determine when expenditure on rehabilitation should stop. The answer to such a question requires consideration of the full range of social, as well as private, costs and benefits of rehabilitation at a particular site. Clearly these costs and benefits will vary between sites. From both an economic and policy perspective it is important to establish whether the additional gain from more rehabilitation would exceed the additional cost.It is concluded in the paper that the technical feasibility alone does not justify a paeticular level of rehabilitation activity and expenditure. While more rehabilitation at a particular site may be technically feasible, the additional expenditure incurred in undertaking that rehabilitation may result in little extra benefit. This conclusion has important implications for government policy, particularly with respect to establishing the goals for rehabilitation, criteria for successful rehabilitation and enforcement of rehabilitation objectives.

Jan 1, 1992

By M F. Navarrete

During 2003, different plastic stemming plugs (Cats«, Stemtite«, and Taponex«) were tested in EscondidaÆs Mina Sur, to determine the effect on gas retention time when used in conjunction with drill cuttings in production shots with a blasthole diameter of 10 5/8ö. Longer retention times were expected to provide greater fragmentation and muckpile looseness. In order to determine which plug showed the greatest enhancement of stemming retention, 17 trials were carried out û in the first seven tests, only the Cats were used, in the following five tests, a combination of Cats, Taponex and Stemtite were used, and in the last three tests, only the Taponex plug was used. In the last two blasts, drill cuttings were used without stemming plugs as a benchmarking exercise. Blasts were filmed with a high-speed camera, which could record the detonation times of holes using rolls of shock tube tied to stakes at the hole collars, to act as flash indicators. The camera allowed measurement of the time between charge detonation and the commencement of stemming ejection. In order to obtain the statistical parameters of each one of the stemming plugs used in the 17 trials carried out, the Minitab software was used and a data base was created for it, corresponding to each stemming configuration with the retention time obtained from the filming. Once it was determined which stemming plug provided the greatest enhancement of stemming retention, the impact on the fragmentation was analysed using the WipFrag image analysis software to estimate the muckpile size distribution.

Jan 1, 2004

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963

By Churchill M

One of the significant changes which has occurred in the flotation sector of the minerals industry, over the last two decades, has been the successful development of the very large flotation machine. The last twenty years has seen the volume of the individual cell, available to the industry, increase by a factor of ten. Today, new mills, and existing mill modernization plans, can consider individual cell volumes as large as 85 m3 with the certainty that the metallurgical performance capability of the large machine is inherently as efficient as the smaller machine. The large flotation cell offers benefits to the user such as reduced floor space, lower total power, process control simplification, and reduced maintenance. However, the flotation machine size selection process, based on overall installation economics, must include such factors as process tonnage, flotation kinetics characteristics, and metallurgical performance objectives. This paper discusses the flotation machine size and circuit arrangement selection based on both metallurgical performance and economic considerations. A computer based flotation kinetic analysis technique, which has proven valuable in quantifying the metallurgical response of flotation circuits having different cell sizes and number, is utilized to illustrate the selection of cell size and arrangement best suited to a client's Requirement.

Jan 1, 1991

By R Bertuzzi

Permanent rock bolts in civil engineering are taken as having to serve their design purpose for at least 50 years. In many projects the design life is specified as greater than 100 years. A review of recent Australian tunnelling projects shows that substantial differences exist in the level of corrosion protection provided for permanent steel shafted rock bolts. This paper reviews the current state of practice and sets out what the authors consider to be appropriate requirements for corrosion protection.

Jan 1, 1999

By Weller KR, Lim IL

The high pressure grinding rolls is one of the few new comminution devices that offer substantial savings when compared with traditional crushing and grinding circuits and with SAG milling. The machine has been well accepted in the cement industry, but mining companies have been more cautious in adopting this technology, partly because of wear and availability problems, and partly because of uncertainties in designing circuits which will deliver the power savings without complicating downstream processing. This paper addresses the latter problem by providing a model structure for predicting power draft and throughput from measurements made with small pilot scale high pressure rolls. Three existing models for predicting product size distributions are assessed and suggestions made for future work. The model structure comprises a power equation, incorporating measurements of torque and rolls speed previously used by the authors. Transport through the mill is assumed to be plug flow. Throughput is governed by the equilibrium gap between the rolls, which is determined both by machine settings and the physical properties of the feed material, including its size distribution. Therefore some form of physical testing in a model machine is required to determine throughput parameters. Results from copper and nickel ore experiments covering a wide range of machine conditions are presented and compared with model predictions. Model assumptions are discussed and directions for future work Suggested.

Jan 1, 1993

The methods employed in dressing 'the tin ore up to the required percentage of purity depend mainly on the type of ore crushed.These may be briefly divided into two distinct classes-viz., q, free: milling ore and a complex milling ore. In the former the ore is practically free from the common metallic sulphides, such as pyrites, mispickel, blende, galena, etc., and 1!' clean concentrate of 70 per cent metallic tin can be directly obtained in one continuous act of concentration; in the latter, however, in order to get a good extraction, it is only advisable to primarily concentrate up to 30 to 40 per cent. tin oxide, the rest being the sulphides of the metals. This concentrate is then roasted, re-ground, and re-concentrated up to 70 per cent. metallic tin on a separate set of tables.In the complex milling ore the tin is intermixed very closely with the sulphides, so that it becomes necessary to collect all the mineral present in order to obtain clean tailings. Stamp mills are the most popular machines for the primary crushing in the district, but whether they are invariably the best for the purpose is rather an open question. No doubt for some of the very tough chloritic ores they are the most efficient, but for a brittle quartzose ore, such as the free milling proposition usually is, the writer thinks Oornish rolls would well hold their own, especially when the tin occurs coarse, as is so often the case with this class of ore. Of course, the great drawback to stamps is the excessive quantity of tin slimed and slime tin is one of the problems of tin-dressing-while rolls give...

Jan 1, 1907

By D Ray, D Brett

A clay-capping trial was established in 1996 on Magazine Dump at the Mt Lyell Copper Mine. The trial was initially constructed under the Mount Lyell Remediation Research and Demonstration Program, a co-operative venture between the State and Federal governments. The detailed engineering design for the clay cover included the following features; reshaping and compaction of dump batters, 5 m vertical bench interval, overall side-slopes of 2.5:1, emplacement of clay in four 150 mm lifts, compaction by a 10 t vibrating roller or ætrack rollingÆ on batters with density testing for quality control. A small section at the base of the dump ( The trial also generated certain unexpected findings. Field permeability tests on the cover yielded uncertain results and oxygen remains available throughout the dump. The flow data indicate that, while total outflow has decreased as a result of storm shedding, inputs from groundwater and batter infiltration are still significant. Outflow during the driest weeks of the year may have risen following capping. Detailed assessment of the data is hampered by insufficient pre-capping information; however, there is a possibility that conductivity flux emitted when flows in the receiving environment are at their annual minimum is unchanged or worse post-capping.

Jan 1, 2003

By T Ross, S Cameron

The requirement to use explosives in ground temperatures exceeding 50¦C is becoming more common as mines work to maximise the recovery of their resources. Orica Explosives was requested to assist in the development and implementation of æhot blastingÆ safe working procedures at Liddell Coal Open Cut in the Hunter Valley. The mine operator, Hunter Valley Earthmoving (HVE), had to contend not only with elevated temperatures in their overburden resulting from burning coal beneath, but also old underground workings which tended to exacerbate the problem. The paper discusses the following issues:the consultative process that was used to develop the procedures employed to ensure the process could be carried out safely; the technical issues surrounding blasting in hot ground, including temperature monitoring, product selection, application and design to ensure safety and performance were maintained; the need for confidence and trust in the team that was working together in a potentially hazardous environment, the emotive issues that were encountered and how they were addressed; the value of a regular review process combined with open and honest communication to ensure the procedures represented best practice and that all stakeholders understood the process; and the value delivered to Liddell Coal when sterilised areas of coal became accessible with little disruption to the mining process. The paper also discusses the challenges that were encountered in the Reservoir Block where proximity to major power lines and rail infrastructure meant that hot blasting procedures had to also consider vibration limits and the need for Energy Australia to disconnect the power.

Jan 1, 2001

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

Low-grade, porphyry copper type mineralization at the Moonmera prospect is related to the intrusion of a granodiorite porphyry mass into the Upper Permian "Gracemere granodiorite". Significant copper mineraliza- tion appears to be associated with the alteration assemblage quartz-sericite- kaolinite. The ore shell is surrounded by a zone where montmorillonite and kaolinite are in greater abundance and this assemblage is over- lapped, mainly at depth, by potassium feldspar alteration. Secondary biotite is abundant throughout the mineralized zone. Preliminary sulphur isotope results on the sulphide mineralization are compatible with a magmatic origin for the sulphur.

Jan 1, 1974

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

By Tsuchida N

The history of world nickel production has been affected significantly by the supply and demand situation and fluctuation of LME price of nickel metal. In the beginning of the 1980s, the decline of price and demand lead to the withdrawal of un-competitive producers and the shrinkage of the production capacity. During the same period, Sumitomo Metal Mining maintained the production level with continuous improvement of the traditional matte electrorefining process. However, Sumitomo has recognised that the continuous improvement alone does not promise us the ability to catch up with rapid changes in the world. In the meantime, Sumitomo intensively researched chloride hydrometallurgy and has developed the chloride process for the nickel refining. This includes the solvent extraction and chloride electrowinning in the mixed sulphide process and the chlorine leach of the anode slime arising from matte electrorefining. In the late-1980s, Sumitomo Metal Mining decided to develop a new nickel refining technology based on chloride hydrometallurgy. The new process was designed from the comprehensive aspects involving safety and the environment. Construction of the plant for the matte chlorine leach electrowinning (MCLE) process was commenced in 1991. The MCLE plant with a capacity to 2000 tonnes per month has been commissioned at Niihama since 1992. The process has provided high productivity, overall good economics and high quality of electrolytic nickel produced. After the establishment of the process, Sumitomo has maintained continuous improvement of the new process and has attained the best practice of the work classification.

Jan 1, 1996

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

By Miyashita T, Yamamoto R, Kishimoto s

Following considerations of the effect of furnace size on pressure loss, pressure loss in front of tuyeres, gas flow in the lower parts of the furnace, the distribution of the burden and the gas flow in large blast furnaces is examined with particular reference to the burden distribution at the throat and the gas flow at high production rates. Improvement of gas flow is related to application of super-high top pressure and the use of moveable armour. A brief description of the NKK type moveable armour is given and its use in controlling the gas flow outlined. The operating results under controlled gas flow show an increase in production of Fukuyama No. 5 BF from 9,200 tpd to 11,000 tpd with a decrease in the fuel rate from 490 kg/thm to 460 kg/thm.

Jan 1, 1975

Within the Business Process Improvement Program initiated at Placer Dome during 2003 was the Business Performance Management Project (BPM).BPMÆ s aim has been to extract productivity improvements from individual business units by providing a model for implementing leading practice based management process within the Placer Dome Group, sharing management best practice, injecting new management techniques and instilling a continuous improvement culture. The installation of an underground dispatch system has been a key component of the BPM project at Osborne Mine.Information capture and analysis allows for corrective action to be planned and executed before there is a material impact on the performance of a business unit. This paper briefly describes the principles and practices of effective business performance management, the four processes of a management operating system namely; strategic and tactical planning, implementation and reporting. The identification of business drivers, their measures and associated key performance indicators is discussed. The benefits of an underground dispatch system at Osborne with respect to safety, production and maintenance is described along with the installation process within the mining department that included its configuration, resourcing and roll out.

Jan 1, 2005