Search Documents

The paper describes the reasons for the development and for the selection of systems which were finally adopted; further estima- tion and design engineering problems, as well as experience with large screens in operation. Advantages, disadvantages and the final li- mits of screen dimensions are indicated.

Jan 1, 1984

By Mutmansky J. M, Hartman H. L

Multiple operating points for mine fans are a problem that fan and mining engineers must constantly be aware of in mine/fan systems. In a single-fan system, unstable conditions can be avoided by restricting fan operation to the "normal operating range." When mine fans are operated in parallel, the situation becomes a little more complicated. Multiple operating points are more often encountered and the fan user must be aware of these multiple points to have a suitable set of operating conditions. However, for fans in parallel, the engineer can plot the combined characteristic in a relatively straightforward manner and thus can avoid conditions that would cause instability in the mine/fan system.

Jan 1, 1988

By Wilkinson RDB, Van Der Meer FP

In order to overcome the statistical limitations imposed by the need to recover density tracers by hand, magnetic density tracers were developed to determine the efficiency of dense medium separators treating porous materials. The tracers were manufactured by extrusion of polypropylene ferrosilicon mixtures and subsequently coated with a distinctive paint to allow hand sorting according to density. Fifteen tracer batches were manufactured in the range 1.61 - 1.94 g/cm3. The tracer densities were determined by a hydrostatic method. The tracer method was applied to the dense medium separation of a Moroccan oil shale in a pilot scale Dyna Whirlpool separator. For each test, about 20,000 tracers were added with the plant feed and subsequently recovered from the products with a dry low intensity magnetic separator. The Tromp curve determined by conventional heavy liquid analysis was displaced towards lower densities compared with that determined by tracers, indicating that the porous shale particles absorb heavy liquid. It is concluded that for porous materials like oil shale and coal, the tracer method gives the most accurate results. In pilot scale testwork the tracer method is also much faster than the conventional heavy liquid analysis, as rather large samples have to be processed by the latter method to ensure Representativeness.

Jan 1, 1987

High precision GPS systems for mining are accurate to within a few centimetres. Typical systems consist of one or more GPS antenna, GPS boards, sensors to detect the position of the blade or bucket of the machine radios to pick up correction signals, a computer to control the system and a display screen to give instructions and information to the operator. GPS systems offer two benefits û they give information to the operator to get his job done faster and more accurately and they can send information to management about how the job was done. On dozers, GPS systems allow the operator to accurately complete earthmoving jobs with no survey pegs. On hydraulic excavators the systems can be used to accurately locate the position of the bucket teeth for selective mining. On blasthole drills the systems can guide the operator to each hole and record accurate as-drilled plans. By reporting the position of the blade or bucket in three dimensions it is possible to continuously upgrade a mapfile of the excavation. From this file it is then possible to report productivity numbers in real time. High precision GPS works best with a minimum of five satellites visible. This may be difficult in a pit. Systems which also access the Russian GLONASSS satellites offer significantly better uptime. GPS systems will become indispensable for efficient mining operations in the future.

Jan 1, 2003

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992

By G R. Ballantyne, M S. Powell, M Tiang

This paper reviews the proportion of energy attributable to comminution within the Australian gold and copper mining sector. The need for this is motivated by inconsistencies in the quoted energy usage data and the lack of a common basis for reporting the fraction of energy in mining that is attributable to comminution. This study should form a reliable basis from which to assess both demand and opportunities to reduce energy consumption.The proportion of milling energy was calculated for the major producers in the Australian gold and copper sector. A sampling methodology created by Powell et al (2003 - 2010) was initially used to provide an accurate and meaningful measure of the energy used in the comminution process. However, no useful method for grouping similar mines was found. Fortunately, a surprisingly large amount of high quality data was found from a number of different sources, allowing the development of robust relationships to be used to estimate a high proportion of the unknown values. The fraction of energy attributable to comminution was found to be dependent on how the total energy consumption was defined. For instance, comminution accounted for 52 per cent of the electrical energy, but only 21 per cent of the total energy publicly reported by the mines because a substantial proportion of energy used on a mine is in the form of transportation fuel (mostly diesel). Critically, the measured electrical energy consumption does not account for transmission and generation losses, while diesel energy usage is typically quoted according to its calorific value. This review proposes that diesel should instead be converted via the mechanical efficiency factor for diesel engines. Using this conversion, comminution was found to account for 36 per cent of the available energy on average. This approach allows a useful basis of comparison for mines regardless of whether milling energy is obtained from electrical or diesel generation. A summary of the results are shown in Figure 7 with other values obtained from literature. The total comminution energy assessed in this study accounts for 1.3 per cent of AustraliaÆs electricity consumption, this figure will increase as the other mineral commodities are added to the study.CITATION:Ballantyne, G R, Powell, M S and Tiang, M, 2012. Proportion of energy attributable to comminution, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 25-30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K Steamy, D Lesmana, K Yulia

Effective selective mining relies heavily on high quality geological data and assay data. Such assay data is dependent on effective sampling protocols, sample preparation techniques, assaying practices and well founded quality assurance/quality control (QA/QC) procedures. This paper describes recent developments in grade control sampling at PT Nusa Halmahera Minerals high-grade Kencana gold mine at Gosowong Indonesia and presents a case study in identifying, minimising and monitoring random and systematic sampling error including the use of duplicate sampling and the Thompson Howarth technique for quantifying random sampling error.

Jan 1, 2009

By Jackson E

The general level of awareness amongst members of the professions that they are faced with an increasing number of claims for breaches of their professional duty was dramatically heightened by the decision of Rogers J. at first instance in Cambridge Credit Corporation v Hutcheson (1985) 3 ACLR when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million - well in excess of their insurance cover. No comfort should be found in the fact that this decision was overturned on appeal, for that result rested on the issue of whether there had been a causal connection between the breach of contract which had occurred and the loss suffered rather than on the fundamental principle of auditors' liability.

Jan 1, 1989

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

By Fraser CJ

Stability control plays a prominent part in the planning and execution of coal winning in the deep open cuts in the Latrobe Valley operated by the State Electricity Commission of Victoria (SECV). Different stability mechanisms affect the individual overburden and coal faces. These are the classical rotational slip in overburden and the three-dimensional tetra- hedral wedge or planar block slip in the coal faces. The stability of the overall batters is affected by the so-called "block sliding" mechanism, which is unique in Australian open cuts. The basal stability of the open cuts is affected by pressure from water in confined aquifers underlying the coal being excavated. This paper describes each of these mechanisms and the current monitoring and con- trol techniques practised by the SECV.

Jan 1, 1982

By Thatcher R

In areas where land suitable for development is a scarce resource, an upgraded post-mining land use can result in economic benefits to both the mining company and to the community.A study undertaken at Aberdare Colliery near Ipswich during 198611987 assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed fmal land use plan comprised a combination of these uses that can be upgraded to higher valued uses once subsidence monitoring of backfilled open-cut areas and dumps indicates that total settlement has reached acceptable levels for development to proceed.The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled open-cuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1990

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

My forebears migrated to South Australia in the 1830s, 1840s and 1850s. All of them were literate but, because they moved about South Australia looking for work, family papers have become scat- tered and I am left with a few fragments. Some years ago I was intrigued to find among my fath- er's books a frontispiece in an old Anglican Book of Lessons. As can be seen Joseph, a mining smith, was also a Freemason. Thus my interest was aroused. I know some- thing of modern day mining communities in South Australia and wondered what they were like 100 or more years ago.

Jan 1, 1987

The process of mine planning at AnacondaÆs nickel and cobalt laterite operation located at Murrin-Murrin in the Northern Goldfields of Western Australia is carried out in a number of stages in an endeavour to determine the optimum mining sequence in order to maintain supply to the 4 Mtpa plant subject to operational constraints. The 296 Mt @ 0.99 per cent Ni and 0.064 per cent Co ore reserve (based on a cut-off grade of 0.8 per cent Nickel) is spread geographically widely over three regions comprising Murrin North (15 km + 15 km), Murrin South (7 km + 16 km) and Murrin East (5 km + 13 km) (refer Figure 2). The nickel mineralisation has been broken up further within each region into 18 separate manageable block models representing the 32 different deposits. The models are based initially on the 50 m + 50 m resource drilling for long term planning and updated with 12.5 m + 12.5 m grade control drilling prior to mining. Each of the individual block models are optimised using Whittle 4X software to provide the shells used as the basis for each of the 126 pit designs. The pits are generally nested with starter pits targeting the higher value shells with subsequent pits incrementally cutting back ultimately to the life of mine shells. A series of steps including: the coding of the individual pits into the block model; data export; TCL scripting (to calculate additional economic and tracking information); importing; and re-blocking; completes the transfer of the data into a MineMax (mixed integer linear programming schedule optimising software) model. Using MineMax and the application of operational and production constraints allows the optimisation, assessment and economic evaluation of alternative scenarios in order to determine the optimum life of mine plan and schedule.

Jan 1, 2003

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995

By D J. Clark, S Hewson, T Li

Cadia Hill Pit is a gold copper porphyry deposit hosted in monzonite. The pit slope design is primarily based on structural controls related to faults and shears with largely massive rock masses between the structures. The slope design attempts to achieve an optimum configuration at a bench to overall scale, considering economics and safety implications against the geotechnical and structural conditions. To date the slopes have been mined at interramp angles of up to 60¦ over heights of 120 m. Limited slope and batter failures that have occurred are structurally controlled and occur rapidly. The pit-mining schedule requires concurrent mining of part of the final pit walls and the progressive interim cutbacks. Engineering and operational solutions to hazard reduction and risk management issues have been implemented wherever viable to æengineerÆ out the hazard and mitigate the risks. However, comprehensive management plans and operating procedures have also played a vital role. This paper details the management plan and the operating procedures that have been developed and implemented to mitigate the risks associated with rock falls.

Jan 1, 2003

By J C. Macintosh

Capcoal Mine has modified its water use practices over the past 15 years. Two issues have changed the way water was managed:an economic review of water supply options for a planned expansion of the coal handling and preparation plant (CHPP) in the early 1990s, and increasing neighbour concerns about discharge of worked water from the mine into the local streams. These issues resulted in commitment by the site General Manager to cease discharge of worked water from site and to convert from using raw water to worked water in the CHPP. Operational needs, societal demands and continuing dry weather are again demanding change to the siteÆs water management strategy. This paper outlines the drivers for past and future operational change.

Jan 1, 2006

Using a Jarrell-Ash "Compact" direct reading spectrometer, analyses were made of a wide variety of rocks ranging from acidic to ultrabasic types. Statistical evaluation suggests that accuracies comparable with the values obtained by the rapid chemical methods used by the United States Geological Survey will be obtained.The spectrographic method involves fusion of the rock with lithium tetraborate, strontium being incorporated in the flux as the internal standard. The resulting bead is ground with graphite and pressed into a pellet. The counts obtained on two standard pellets are used to correct for instrumental drift.Background readings are made at 4109 Å and corrections for background are made to all lines. Corrections for matrix interferences, both by chemical suppression and optical enhancement, are made. The three corrections of drift, background, and matrix are incorporated into one general expression which has been programmed on magnetic cards, each element requiring a separate card. The cards are placed individually into a desk top computer (an Olivetti Programma 101), which enables true counts to be calculated from the "readout" counts, and the element concentration is then obtained from computer-printed tables by referring to the appropriate value of true counts versus concentration. These tables were prepared by making a polynomial regression analysis of the spectrographic results from 50 standard and analysed samples, a curve of best fit being chosen for each element.The regression coefficients, usually of a fourth or fifth degree equation, together with other relevant data, were fed into a large computer, programmed to print out tables of concentration versus true counts. This technique enables the results obtained to be based on mathematically-derived values rather than on hand-drawn calibration graphs, giving greater inherent accuracy. The technique has been shown to give results of good accuracy and acceptable precision suitable for many geological and geochemical exploration programmes involving the analysis of many rock samples of different types.

Jan 1, 1969