Search Documents

By M Haest, S Sandler, R Botha, H Lang, K Hume

Benchmark practices in the mining industry include the establishment of Quality Programs — Quality Assurance and Quality Control (QAQC) — to monitor the correct execution of sampling protocols and control each stage of the ‘Sample Cycle’: Sample Collection, Preparation (comminution) and Analysis. QAQC reports commonly include statistical-numerical results that quantify performance of QAQC controls (field duplicates, preparation duplicates, blanks, standards etc). Graphics such as scatter plots, QQ plots, histograms and cumulative frequencies are used to represent the results. Statistical values including relative difference, absolute difference, relative variance, averages, T-test, and Zscores are used to quantitatively express the relationship between duplicate pairs ... but is an effective quality program just a statistical exercise? This paper aims to highlight the concept of ‘Quality Management’ (QM) as the precursor of continuous monitoring (ideally in real time) of QAQC results on Exploration, Production, Processing and Port samples, determined by trend analysis performed on a time and/or grades basis. Currently, there is a paradigm in the process of quality assurance that if individual data points fall within a predetermined acceptance limit then they are ‘acceptable’ and therefore suitable for informing operational and investment decisions. However, what is stated with respect to QM is that sometimes results found within the acceptance limits can indeed be internally biased, or show material deviations over a period of time, thereby impacting reconciliation results and/or potentially creating discrepancies with the final buyers. QM refers to the proactive detection of these ‘anomalous tendencies’, the approach and communication with the source of the information, the understanding of the reasons that cause the deficiencies, and the generation of agreed action plans to remediate the situation and ensure the consistency of results, in other words: continuous improvement on proactive manners.

Mar 22, 2022

Coal washery wastes comprise tailings, finer than 0.5 to 0.1 mm depending on the sophistication of the washery, and coarse reject, typically finer than 50 mm. Subaerial disposal of coal tailings slurry at about 30 per cent solids by mass results in the formation of a delta with an average slope of about 1 in 100, representing one extreme. The ravelling of coarse reject on loose-dumping, results in an angle of repose slope with an angle of about 37o (1 in 1.3), representing the other extreme. The pumped co-disposal of coal tailings and coarse reject results in the formation of an upper delta with an average slope of about to one in ten, between the two extremes. The depositional behaviour of these three waste streams is discussed and compared in this paper. The important depositional and material parameters, and a theoretical description of the processes involved, are also presented. Comparisons are made between the depositional behaviour of the various coal washery waste streams, and natural depositional systems, such as rivers, alluvial fans, and scree slopes.

Jan 1, 1998

By C Fong

Compliance Planning is an active approach to ensure mining operations align more closely to their longer-term plans. Through Compliance Planning, operations can not only measure their performance on intervals as short as intra-shift, but they can then apply corrective measures to ensure they remain as close as possible to the plans. Compliance Planning targets short-term and execution level teams, as these are the shortest duration planning divisions commonly found in mining operations. Compliance Planning combines live information with intelligent planning capabilities to provide a framework that enables mining operations to realise a significant improvement in reconciliation of plan to actual movements.

Jun 22, 2022

By C Augustin, M Hahn, K Nienhaus

Operators of mining machinery like haul trucks or excavators have very limited information about the exact distance to other equipment as well as to the natural boundaries like berms, walls and structures such as crushers. The industry is seeking solutions to provide safety and positioning. The authors have developed a solution approach which is being used in several installations. This solution consists of three parts: first robust and compact two-dimensional (2D) radar scanners that provide range and angular information of the environment especially under difficult conditions like dust, rain, snow and fog; second an intelligent data processing framework flexible enough to adopt to different machines and operation modes like speed, inclination, visibility, tire friction, GPS position, orientation and acceleration; and third a high quality and easy to use interface giving highly condensed data to the operator, not blinding the operator at night and being sunlight readable. The truth of present proximity detection sensors is that they not only have a high false alarm rate but furthermore cover only a fraction of the possible scenarios. This makes them unsuitable for stand-alone collision avoidance systems. On the other side, mine dispatch systems only deliver database and GPS information, but no information regarding the real environment. The indurad company and its Australian partner CTS (http://www.cts.com.au) addressed these aspects by developing smart productivity enhancement driver assistance tools like lane and crusher dumping assistance.An innovative driver assistance tool developed in cooperation with the coal shearer manufacturer Eickhoff and the RWTH Aachen University has been awarded with the annual research award of its customer RAG, being the largest German hard coal producer, as well as with the bauma Innovation Award in 2010.

Sep 26, 2011

By A Gibbs

The mining sector has been a leader in investing in safety improvement initiatives, yet relatively few mining organisations can accurately track the positive effects of these initiatives or identify areas that may require more attention. The consequences of not taking safety seriously are severe, and unfortunately injuries and fatalities are continuing to occur across the mining sector (Brady, 2019). There is a tendency to turn to lag indicators such as All Injury Frequency Rate (AIFR), Total Recordable Injury Frequency Rate (TRIFR), and Lost Time Injury Frequency Rate (LTIFR) to track these outcomes. As outlined below these approaches are inherently flawed and a renewed focus is needed on indicators within the control of leaders, indicators that have high predictive validity for future events and data that is used in a way to enable learning and change.

May 5, 2022

By D Drinkwater

In 2009, Peter Munro and Peter Tilyard examined the “human capital” in the mineral processing sector in a paper entitled Back to the Future (Munro and Tilyard, 2009). One of their major concerns was a general decline in technical skills and process knowledge, exacerbated by lack of appreciation of the impact this can have on process plant performance and, ultimately, profitability or sustainability of the industry. There are many reasons for this decline, not least of which are the work schedules of today’s metallurgists which have a very different balance between technical and non-technical responsibility than those in the past. However, a shift towards a more technical focus has potential to deliver a range of benefits for industry at large and for the individuals in it This paper discusses some options for development of core metallurgical and process engineering skills that can be used by graduates, employers and training providers.Key skills are identified and mapped against available opportunities for development, such as existing graduate programs, on-the job training and external courses. The authors also review a number of past and present high-quality graduate development programs, including the graduate development program in place at Mount Isa Mines in the 1980s and the Anglo Platinum Graduate Development Program (AGDP) currently operating in South Africa.

Aug 8, 2011

By A G. Grice

WMC Resources Pty Ltd û Copper Uranium Division operates the large underground Olympic Dam Mine at Roxby Downs, South Australia. These operations mine and process the ore to produce refined copper, uranium oxide, gold and silver. In mid-1996, the company committed to the Olympic Dam Expansion Project (OEP) to expand production from 3.0 million tonnes per annum of ore (85 000 tonnes per annum of copper metal) to over 9.0 million tonnes per annum of ore (over 200 000 tonnes per annum of copper metal). Along with the increase in the ore production capacity of the underground mine and the surface ore handling and processing facilities, expansion of the backfill system was required. The target backfill placement rate was 2.0 million cubic metres of backfill per annum which was to be predominantly delivered as cemented aggregate fill (CAF). This paper discusses the engineering activities undertaken to assess and change the method of designing the required strength of fill exposures. In addition, the operational changes that were introduced to achieve the required fill quantities and the mix designs to meet the specified strengths, including the use of alternate binders, are discussed. This work resulted in a large increase in the fill placement rate and a reduction in the overall unit cost of fill.

Jan 1, 2000

By J J. L du Plessis

Escalating energy and electricity costs have become one of the biggest expenditure drivers in mining operations. During the last eight years, energy costs have trebled when expressed as a percentage of total running cost in South African mines. Power consumption on mines is controlled by three main strategies, namely load clipping where energy use is reduced for parts of the day, load shifting where energy use is shifted to other parts of the day, and energy efficiency where energy use is reduced permanently.To reduce the operating costs of ventilating and cooling underground mines continuously, system optimisation studies must be completed. A part of this paper describes methods that can be used to reduce energy usage by optimising cooling and ventilation systems during planning and in existing operations using network simulation models that accurately reflect the current and planned ventilation conditions. These models are used to examine various options for improving the overall ventilation and cooling efficiency. Furthermore, an overview of refrigeration and cooling practices, and ventilation strategies is presented.Ventilation-on-demand and cooling-on-demand strategies have the potential to reduce both the capital and operating costs associated with mine ventilation and cooling systems. In addition, it has been proven that modern strategies and energy-efficient tactics are technically feasible.It is also important that the correct equipment selection is made. This must be based on the best technology with the highest energy efficiency. Where equipment replacement is being considered, energy efficiency must be one of the key decision drivers.In this paper a number of studies were presented and from the experience and the data presented it is clear that a large financial benefit is possible through optimising ventilation and cooling during the planning of mines or within an existing operating mine.CITATION:du Plessis, J J L, 2015. Strategy and tactics implemented to achieve energy-efficient ventilation and cooling of mines, in Proceedings The Australian Mine Ventilation Conference, pp 9–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Darvall

Magnetite ore blending has yielded signifi cant performance improvements in OneSteel’s magnetite concentrator. The magnetite concentrator beneficiates magnetite ore from the Iron Magnet Deposit and produces concentrate, which is pelletised, then fed to the OneSteel Whyalla blast furnace. Concentrator feed variability severely detracts from the concentrator’s performance, affecting both concentrate yield and grade, which impacts on all downstream processing costs.A coordinated approach has integrated mine planning, geological modelling and grade control, to minimise concentrator feed variability, through effective ore blending throughout the mining and stockpiling process.Mine planning personnel design shots that extend the full width of the orebody and hence across the stratigraphic profi le. Based on geological information contained in block-outs and in consultation with Geology, the Grade Control team allocates material to each primary stockpile, potentially from every stratigraphic domane in the orebody. This ensures primary stockpiles are designed with maximum practical homogeneity and consistency.Using only primary movement, the allocated ore is stockpiled in a layer-cake fashion. The ore is pimple dumped across the width of the stockpile footprint and on completion of a layer, it is dozed flat with an access ramp that allows dumping to commence on the next lift. The primary stockpiles are reclaimed normal to build direction and the magnetite is crushed, all in, to a concentrator feed stockpile.The ore is sampled at the crusher from a falling stream cut. These assay data, are used for benchmarking and control charting the grade and variability of concentrator feed stockpiles. The concentrator feed stockpiles have demonstrated a statistically signifi cant reduction of within pile variation, between pile variation and pile to pile variation, primarily attributable to the development of ore blending. The concentrator has seen sustained, improved performance as a direct result, which translates into lower concentrate cost per tonne and improved yield and quality.

Jul 11, 2011

By A K. Ghosh, J Chung, E Topal, M Asad

"Many open pit (OP) mines with considerable vertical extent are approaching the end of their life-of-mine; some of them are seeking the opportunity to make the transition from OP to underground (UG) mining. The decision on the best location for transition from OP to UG mining should be addressed at the strategic mine planning stage. Conservatively, the transition to UG mining is considered near or after the exhaustion of the reserve within the ultimate pit.However, if UG is evident and exclusively viable from the inception, defining the best location for the transition through a conservative approach may not be an optimal option to explore. This clearly establishes the need for a mathematical model that aims to maximise the project value and considers OP and UG mining with crown pillar (CP) requirement simultaneously. Underground mine layout varies from one UG mining method to the other, and consequently the variation in the location of transition is eminent. Thus, focus on the selection of UG mining method must be a part of this analysisThis paper presents an implementation of an integer programming (IP) based mathematical model that evaluates the changes in mining layout and the project value under possible variation in the transition point from OP to UG mining for stoping and block caving methods. An IP problem is a mathematical optimisation or feasibility method in which some or all of the variables are restricted to be integers. The outcome of the implementation reflects that mining strategies with OP transition to stoping and block caving methods generated higher values than OP-only mining strategy. The case study not only demonstrates the difference in mining layout for both stoping method and block caving method, but also reflects that a joint consideration of OP mining, UG mining and CP placement helps to achieve maximum project value and resource utilisation.Citation:Darbritz, J, 2016. Remediation of Wall Failure at Kalgoorlie Consolidated Gold Mines' Golden Pike Cut-back 2016, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 96–103 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

For effective backfilling, a system with the 13 features covered under the section: effective backfill systems, is required. Effective backfilling cannot be done with systems that are badly designed, outdated or overextended. But in cases where the requirements for effective backfilling are overlooked, the shortcomings of such systems may wrongly come to be regarded as limitations to the capabilities of backfilling per se. Mining is currently done to depths of 3500 m, and is to go deeper since the gold-bearing reef extends down to 4000 m and 5000 m below surface. Effective backfilling systems will be required at such depths, and with suitable design this can be achieved. Mining the narrow tabular orebody of a typical South African gold mine is described at the start of this paper, then cycloned backfilling is discussed in general, and its effectiveness (most of the fill placed in South Africa is cycloned backfill or ædeslimed tailingsÆ).

Jan 1, 1998

North Flinders Mines Limited (N.F.M.) is an Australian-owned mineral exploration and mining company based in South Australia. In the 1970's it researched the prospectiveness of the Tanami (central western region of the N.T.) for the identification of possible economic gold deposits. Having outlined the potential for such a deposit at The Granites (550 km. N.W. of Alice Springs), it marked out and in 1975 applied for the grant of eleven gold mining leases (G.M.L.'s) under the provisions of the then Mining Ordinance. This application was deferred by the Commonwealth Government during the time of the Aboriginal Land Rights Commission (Woodward), subsequent enactment of legislation and land claims. In 1980, the Walpiri and Kartangarurra-Kurintji land claim encompassing the G.M.L.'s, became Aboriginal land. It therefore became necessary for N.F.M. to negotiate a mining agreement with the Central Land Council (C.L.C.) represent- ing the Traditional Owners, before the G.M.L.'s could be granted. In August 1983, the C.L.C. and N.F.M. concluded an agreement to enable the grant of mining interests necessary for the devel- opment of The Granites Gold Project. In several ways this agreement is unique in That:

Jan 1, 1984

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993

By D Shuen, R Sales, D La Rosa

Semi-autogenous grinding (SAG) mill control is complex and depends on many dynamic process variables. Good control strategies ensure that a mill is operating as close to optimal as possible, resulting in significant economic benefits to an operation. Pueblo Viejo, a gold mine in the Dominican Republic, has been actively improving their control strategies since start-up in 2012, and one of these initiatives was to install an acoustic monitoring system on the SAG mill. The data from the system is used to optimise the mill’s performance by limiting the time the mill is either running too quiet or too loud. The lower limit is an indication that the charge in the mill is too high for efficient breakage or that the mill speed is too low and grinding media are not striking the toe of the charge. Conversely, when the acoustic emissions from the mill are too high, this can indicate that the balls are striking above the toe of the charge, resulting in inefficient grinding and excessive liner and lifter wear. Adjusting mill operating conditions to keep acoustic emissions in the ‘sweet spot’ between these limits results in more efficient grinding.Pueblo Viejo installed a Metso SmartEar™ to monitor the acoustic emissions of their SAG mill in January 2013. This system has been installed on many mills around the world and is specifically designed for optimising SAG mill control. One system output is the impact counter which measures steel-on-steel impacts on the mill shell. The impact counter uses both frequency and time domain analysis to approximate the number of ball impacts per minute. This method of analysis excludes parts of the sound signal not associated with steel-on-steel impacts and gives an accurate measure of this critical control parameter. After the acoustic system was installed, Pueblo Viejo collected data to determine the upper and lower limits for the impact count variable. The live data is available to the mill operators and it is used as one of the key operating variables to control the mill.Through continuous improvement and the use of advanced technologies like SmartEar™, Pueblo Viejo are improving the control and operation of their SAG mill, resulting in reduced liner wear, more efficient mill performance and optimised energy consumption. This paper discusses the installation of the system, and the measureable benefits obtained by using acoustic monitoring to control their SAG mill.CITATION:Shuen, D, Sales, R, Wortley, M and La Rosa, D, 2014. The benefits of using SmartEar™at Pueblo Viejo, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Tickner, Y Van Haarlem, G Roach, D Abernethy, M Smith, J OÆDwyer

The development of novel technologies capable of real-time, high-accuracy, automated analysis of gold, other precious metals and mineralogy, both in ore samples and directly on process streams is reported.X-ray fluorescence (XRF) analysis is widely used for process stream monitoring of base metals. However, detection limits are generally a few parts-per-million (ppm) or larger, precluding the use of this method for monitoring precious metals. Complex interferences with other elements also limit accuracy. An XRF slurry analyser that uses advanced data-analysis techniques to resolve overlapping fluorescence lines, achieving detection limits in the parts-per-billion (ppb) range has been developed. This allows feed, concentrate and tailings streams in precious metal applications to be monitored in real-time. An extended trial of our technology in a platinum group element concentrator and laboratory tests on gold process slurries in the 0.1 - 2.0 ppm concentration range is discussed.Analysis of process stream mineralogy can provide useful information to supplement conventional elemental data. An on-stream X-ray diffraction analysis technique that provide real-time mineral and elemental measurement of process slurry streams has been developed. Both X-ray techniques can be combined into a single on-stream analyser to provide simultaneous elemental and mineralogical information. The successful trial of a combined XRDF (X-ray diffraction and fluorescence) slurry analyser is also reported.It is widely recognised that rapid, accurate analysis of grade is an essential prerequisite for optimising the efficiency of exploration, mining and processing of metals ores. The low grades of precious metals ores, such as gold and the platinum group elements, have led to fire assay becoming the predominant analysis technique. Significant drawbacks of fire assay include long turn-around times, limited absolute accuracy, high costs and requirement for skilled operating staff. For rapid measurement of gold samples, a technique that allows the gold content of large samples to be determined absolutely with high accuracy in less than two minutes using activation with high-energy X-rays has been developed. The method is non-destructive, has detection limits in the low ppb range, is capable of measuring slurries, ground or crushed solids with minimal preparation and can be made fully automatic. Initial results from laboratory trials are presented.CITATION:Roach, G, Abernethy, D, OÆDwyer, J, Smith, M, Tickner, J and Van Haarlem, Y, 2013. Advanced instrumentation for analysis of exploration, mining and process materials, in Proceedings World Gold 2013 , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By V S. Vutukuri, K Shariar

This paper present a modification of selected strength criteria for coal and rocks containing weakness planes. The three strength criteria, namely, Murrell (1965), Bieniawski (1974a, 1983) and Hoek and Brown (1980) have been assessed for coal (containing weakness planes) by using triaxial strength tests. Triaxial test results indicated that the strength of coal specimens depends on the weakness plane inclination with respect to the principal stress direction. However it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of coal specimens is reduced. The constant parameters in the three failure criteria for coal are determined for each weakness plane inclination by using the Datafit computer program (nonlinear regression analysis) and the results are compared with other rock types.

Jan 1, 1999

By D Hume

During 2001 the Ridgeway Gold Mine, driven by company initiatives and recent NSW legislation (General Rule 2000), developed and implemented Major Hazard Management Plans to control significant hazards identified at the underground mine. The paper presents the objectives, issues, outcomes and process involved in the development and implementation of the plans at Ridgeway. The sharing of the experience gained and an overview of the intended way forward will offer a valuable insight for other mines considering embarking on a similar journey.

Jan 1, 2002

The introduction of a new mining method to Australia is not without its risks and challenges. This paper discusses the processes of planning a new operation, with particular emphasis on block caving and its Northparkes adaptation. As well as applying advanced technologies, here also is the opportunity to develop the art and science of block caving for its application to a wider range of geotechnical conditions than previously Envisaged.

Jan 1, 1995

By J W. Lee, E Baafi, N Aziz

Ground subsidence due to mining is a common dilemma confronting the underground coal mining industry. The effects of underground longwall mining on river valleys have come under scrutiny, especially when mining is located underneath catchment areas. As public awareness of mining impacts on the environment increases, there is the need to develop damage mitigation strategies. Results of numerical modelling show that river valley response to underground longwall mining can be simulated and evaluated.

Jan 1, 2005

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022