Search Documents

By T. O. Massalski, J. D. Ayers

A massive transformation, 0 —am, takes place in a number of copper-based systems where the ß phase field at high temperatures extends to compositions that are slightly less solute-rich than the limits of the a phase field that exists at lower temperatures. Consequently a solid-state transformation becomes possible that does not involve a change of composition. Within this narrow range of composition the massive am phase can be usually produced in two ways: by a fast quench from the ß phase through the a phase field, or by pulse heating into the a phase field of an undecomposed ß phase retained at room temperature by a prior quench. In the Cu-Ga system the occurrence of a massive am phase has been also observed in alloys whose composition falls outside the equilibrium a phase field1 but not in the Cu-Zn system.2 We have recently observed the occurrence of the ß — am transformation also in two silver-based systems, Ag-Zn and Ag-Cd. The a and 0 phase fields in these systems again slightly "overlap" in a narrow composition range. In the Ag-Zn system this range falls between 36.7 and 40.2 at. pct Zn, and in the Ag-Cd system between approximately 41 and 42.5 at. pct Cd. Alloys were prepared from high-purity materials and cast in quartz tubes under inert atmosphere. No significant change of composition occurred during casting. After homogenizing in the 0 phase field, small pieces of each alloy were reheated at the homogenizing temperatures for a few minutes and quenched into various media. There were examined metallographic-ally after removal of surface layers that may have suffered from contamination or from the loss of the solute element. In the Ag-Zn system extensive areas of the am phase (identified by selective etching, observation of the slip trace variants, and occurrence of twinning) were observed in a comparatively low-zinc alloy (37.8 at. pct Zn) for all quenching media employed: iced

Jan 1, 1969

By F. E. Crane, H. A. Kendall, G. H. F. Gardner

Two effects of a difference in density may be observed in miscible displacement. As the difference is increased from zero there is first a change in mode from multiple fingers to a single finger. A further increase results in a more rapid growth of the single finger. Miscible displacement with multiple fingers has been discussed by Blackwell, et al, whereas miscible displacement with a single finger has been discussed by Craig, et al. In the present paper experiments are described which bridge the gap between these extreme cases. INTRODUCTION Craig, et al,1 investigated the effect of gravity on frontal displacements for circumstances in which the gravity forces were significant. Blackwell, et a1,2 dealt with the other extreme in which gravity forces were negligible. The considerable difference between their results is illustrated in Fig. 1 where the breakthrough recoveries are plotted against the mobility ratio. The experiments described in the present paper were conducted to examine how the transition from the one extreme case to the other occurs when the gravity forces are gradually reduced. The transition is well illustrated by the production history after breakthrough. Fig. 2 shows how the number of pore volumes which must be injected at a constant rate to displace 98 per cent of the original fluid depends on the gravity force. For each mobility ratio there is a transition range, and a very significant change in the number of pore volumes occurs when this range is traversed. This range of the gravity force is physically linked with the formation of viscous fingers. A single finger is predominant for larger gravity forces; a multiplicity of fingers is formed for smaller gravity forces. Improved recovery and the occurrence of multiple fingers is concomitant with a large increase in the amount by which the fluids are mixed within the porous medium. The transition range depends on all the dimension-less groups which characterize the problem; but this dependence has not been exhaustively studied as yet and only fragmentary results are discussed in this paper.

By J. F. Wilkinson

A high degree of accuracy is often required in mine-surveying, in order that expensive mining work may not be misdirected. The making of underground connections by drifts or shafts located as the result of surveys presents a crucial test of correctness not usually involved in any other class of surveying. In view of these considerations, the present notes and description of a survey made in June, 1890, for the San Francisco shaft of the New Almaden quicksilver-mines, may be of interest to members of the Institute who are surveyors. The purpose of this survey was to locate on the surface a vertical 2-compartment shaft (3.5 by 7 ft.), to connect with another vertical shaft, of practically the same size, which had been sunk a number of years before from an adit-level about 240 ft. vertically below the surface, to a deeper, so-called 600-ft. level. It will be seen, of course, that the most important matter was to secure an exact coincidence in vertical line, so that the resulting continuous vertical shaft from the surface should have no offset or irregularity at the point of junction between its two parts. The levels were of less importance; but, as the hoisting-works were to be placed in position and the new shaft permanently timbered from the start, its correct alignment was an essential requirement. The important features of the work, therefore, were the methods used in determining with certainty : 1. That the shaft was located in the right place in a general way; 2. That the ordinary inaccuracies of linear and angular measurements were so reduced as to insure correctness of location within certain defined and allowable limits. Instruments.—Thc instruments used were: a Buff and Berger transit-theodolite, with a 6-in. horizontal plate, reading to 10 seconds; a Heller and Brightly Y-level; a Chestermán steel tape, graduated in tenths and hundredths of a foot; and New York leveling-rods, graduated to thousandths of a foot.

Jan 1, 1901

By John Chapman, J. C. Vaughan

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By J. C. Vaughan, John Chapman

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By J. H. Frye, D. L. McElroy, E. E. Stansbury

The rates of growth of pearlite in high-purity Fe-C alloys have been measured as a function of the transformation temperature. These and other data have been correlated in terms of a derived rate equation. Activation energies for the growth were found to be 24,200 cal per mol of austenite for the 0.78 pct C alloy and 27,600 cal per mol for the 0.93 pct C alloy. Theoretical implications are discussed. AN excellent review of the the theoretical and experimental studies on the mechanism and kinetics of the eutectoid reaction has been presented recently by Mehl and Dube.' They have pointed out that these investigations have followed two lines of approach: 1—experimental studies and derivations of expressions for the overall transformation characteristics, and 2—derivation of expressions for the nucleation and growth rates in terms of fundamental processes. Investigations of the latter type have been concerned for the most part with the nature of the growth at the austenite-pearlite interface in plain carbon and alloy eutectoid steels. They discuss two theories of the rate of growth of pearlite from aus-tenite—those of Brandt and of Zener. Both derive rate equations which are based on the assumption that carbon diffusion is the controlling mechanism. Mehl and Dube,' Zener,2 and Brandts. " have attempted to calculate growth rates by use of these equations together with thermodynamic and diffusion data. The results are encouraging, but agreement is not so good as to constitute verification of the theories. Furthermore, it Is not clear how these equations are to be used to study the effect of alloying elements which apparently exert little influence on carbon diffusion, but markedly decrease growth rates. It is not clear whether or not the addition to iron of an alloying element which does not diffuse during transformation can alter the rate of growth of body-centered from face-centered cubic iron. That it can greatly decrease the overall transformation rate has

Jan 1, 1954

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By A. M. Gaudin, D. W. Fuerstenau

By streaming potential techniques, the zeta potential of quartz has been measured as a function of the concentration of dodecylammonium salts at different pH values. These experiments indicate that adsorption of dodecylammonium ions takes place as individual aminium ions until a certain critical concentration is reached in the double layer, at which point the adsorbed collector ions begin to associate into patches of ions, called hemi-micelles. Because of its effect on the surface potential of quartz, pH controls the adsorption of dodecylammonium ions. The value of cooperating agents and nonionized constituents of flotation systems is discussed. A PREVIOUS investigation' of the role of pH in the flotation of quartz with anionic collectors is here extended to an inquiry of how the cationic collector, dodecylammonium acetate, is adsorbed at the quartz-solution interface. The equilibrium amount of this collector adsorbed by quartz has already been measured as a function of concentration and pH.2,3 The weight of prior evidence has suggested that two mechanisms are involved in the adsorption of this collector by quartz, but with existing adsorption measurements alone it is not possible to determine what the mechanisms are. Gaudin and Bloecher2 postulated that a polymolec-ular adsorption coating begins to form before the first monolayer has been completed. Gaudin and Morrow4 indicated that a similar situation might exist in the film of dodecylammonium ions on hematite. A study of electrokinetic potentials at the quartz-solution interface provides some detail toward a fuller understanding of the adsorption mechanism. Experimental Results The zeta potential at the quartz-solution interface was calculated from streaming potential data measured with the apparatus described in detail in a thesis by Fuerstenau5 and briefly in a paper by Gaudin and Fuerstenau.1 The quartz used in these experiments was a 48/65-mesh fraction prepared in the manner described previously.' Zeta potential of quartz was obtained for various amounts of the amine salt at pH 4, 7, 10, 11. In

Jan 1, 1956

By B. E. Thompson, H. B. Fuqua

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (d) of the liquid-to-solid transfer at each temperature has been derived: d = ZLXL(XL - P) + Zsxs(P- ZL(XL - P) + Zs(P - Xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, XL and xs are the composi-tions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under considera-tion. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d -versus-temperature curves for two alloys Pl and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid FIG. I.-GENERAL SOLID SOLUTION DIAGRAM SHOWING S CURVES FOR ALLOYS P1 AND P2. phase only at the temperature of the be-ginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate tem-perature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1940

By J. H. Bowden

The water-hoisting tanks herewith illustrated have been designed for removing large quantities of water from recently-flooded mines, through their hoisting-slopes, with rapidity proportional to the capabilities of the hoisting machinery available, the tanks being adaptable to slopes of small sectional areas and varying pitches. The following features may be of interest to those operating mines liable to be flooded. 1. The arrangement of doors on each tank by which it may be automatically filled by immersion at any point on the varying pitch of a slope, the water being retained while hoisting on the flat as well as on the steep pitches, and quickly and autoniatically discharged at the top. 2. The arrangement, in connection with the above-mentioned doors, of side-wheels over the rear wheeh of each tank and of sidedumping tracks at the top of the hoist, for the automatic emptying and quick return of the tank. 3. The arrangement of two or more tanks, one in front of the other, so as to give as large a capacity in a single hoist as the enginepower will permit, yet without making any tank too large for the sectional area of the slope, or of unwieldlp length, or of such a shape that it cannot easily pass over vertical curves; and without concentrating too much weight on any one pair of wheels or on any point of the track. The details of construction and method of operating are shown by the accompanying sketches (Figs. 1 and 2), and the following more detailed description. At the end of each tank is a large iron door of almost the full size of the end of the tank, opening inwards, so that when immersed the tanks fill almost instantly. To provide for holding the water while it is hoisted up flat pitches, a wooden door is attached to the front of each tank, opening outward. Each front door is attached to the

Jan 1, 1892

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By Alexander L. Field

In the light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and Egan,l it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550" C., when concentrations of carbon and FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant—a circumstance which might have been predicted from theoretical considerations. At 1550" C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550" C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020 = 2.3 per cent. effective 0.0086 FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By H. Biloni

A metallographic study of solute segregation produced during controlled solidification of Sn-Pb alloys has previously been reported.' It was found that the growth conditions which produced well-developed cellular substructures led to severe segregation, and even at solute concentrations of 0.2 wt pct Pb regions of a lead-rich phase were formed at the junctions of cell boundaries (nodes). Similar sample preparation and etching techniques have now been applied to several tin alloys at more dilute concentrations. The crystals were solidified uni-directionally under less-severe growth conditions so that the predominant interface structure was composed of two-dimensional cells.* Binary alloys with lead, using 9.999 pct Sn as a solvent, and ternary alloys with lead and bismuth or lead and antimony, using zone-refined tin as a solvent, were examined. The liquid was decanted from the growing crystals in all cases to reveal the interface structure and ensure that two-dimensional cells were being formed. However, since interference may arise from a liquid layer that clings to the interface during decanting,3 an examination of the segregation pattern was always made behind the interface. In all cases, the structure within the bulk of a crystal at greater than 1 cm behind the decanted interface was substantially the same as that nearer the interface. Representative photomicrographs of the dilute Sn-Pb alloy are shown in Figs. 1, 2, and 3. Most observations are similar to those of the previous investigation. For example, the solute concentration at the cell walls is higher than in the intercellular regions; where cell boundaries meet, the segregation is enhanced; the macromosaic or stria-tion substructure and grain boundaries show enhanced segregation; there is also a depletion of solute at cell walls near a striation boundary, as Spittle et a1.4 have observed at decanted interfaces. Not all these observations can be seen in the photos shown since attention has been focused on a special feature; as evident in the photomicrographs, cer-

Jan 1, 1965

By William A. Longacre

IN a previous paper1 the author discussed the problem described by the title of this paper, outlining and reviewing the Gish-Rooney method, with comparison and brief analysis of the interpretation techniques of Roman2 and Tagg.3 Some aspects of the simple type of two-layer system were reviewed from various sources.4,5,6 THE TWO-LAYER PROBLEM For the configuration shown in Fig. I, and for any electrode separation A, the apparent resistivity is a function of the relative depth [HA], the overburden resistivity pi, and a factor K defined by the equation [ ] where p2 is the resistivity of the lower bed, Thus, by the known theory of electrical images, [ ] THE MULTILAYER PROBLEM As the number of isotropic, homogeneous, horizontal layers increases, the difficulties of interpretation multiply. The theory becomes much more involved, and in view of the state of our knowledge, the general problem is virtually impossible of exact solution. However, certain types of [ ] multilayer problems can be worked out in terms of two-layer theory. Hummel,7 Pirson,8 Tagg,3 Watson,9 and others have pointed out the possibility of building up approximations of multilayer resistivity curves with suitable combinations of two-layer curves. Many three-layer curves can be constructed in this way to a good degree of accuracy, and special types of four-layer curves can be approximated. It is very likely that as the number of layers increases, the method of combination will not give good approximations except in very special cases, In the analysis of actual field data, the author has found that many obviously multilayer curves can be solved partially with a good degree of accuracy, using the theory that thin adjacent beds may be considered as one layer or zone, and applying two-layer theory to the extremities of the field curve. MODIFIED TAGG METHOD OF INTERPRETATION Tagg's second method, though superior to his first, necessitates a large number

Jan 1, 1941

By Shun-ichi Satoh

In the previous paper, the writer indicated that the arc welding of cast iron is practicable only when barium carbonate is used to retard the fusion of electrodes. Later, he tested the effects of 48 other elements, to discover the cause of their retarding action. Wrought-iron bars 33 cm. long and 0.53 cm. dia. were used as electrodes. The chemical analysis of the original electrode is given in Table 1. Table 1.—Analysis of Electrode Per Cent. Carbon.................................................. 0.045 Silicon................................................... 0.028 Manganese....................................... Trace Phosphorus.............................................. 0.047 Sulfur................................................... 0.008 Each of the bars was wound with a twine of asbestos (1 mm. dia., weighing 0.5 g.) and then was coated with a mixture of equal quantities of graphite and carborundum and one of the compounds listed in the second column of Table 2. The method used in coating was as follows: The mixtures were reduced to paste by adding to them a solution of water glass (1:3); they were next put in a glass tube of 8 mm. inner diameter, with funnel-shaped mouth (the same tube shown in the previous paper); then the bars were passed through the tube so that the mixtures were coated on them. The glass tube was used only as a means of making the diameters of all coated bars exactly 8 millimeters. The cast iron was deposited on the steel plates by connecting the electrodes first to the positive and then to the negative pole of the generator. The figures representing the time, voltage, amperes and energy required to melt each electrode are given in Table 2. They are arranged in the order of the atomic weights of the elements contained in the coatings. In Figs. 1 to 4, which show respectively the time, current, voltage and energy required in this operation, the abscissas indicate the atomic weights of the elements contained in the coatings, and the ordinates

Jan 1, 1929

By Eugene E. Ayres

The centrifuge has come into general use in the oil fields and in the establishments where lubricating and fuel oils are used. Probably centrifugal machinery will be found more useful in the refinery when the operators are more familiar with'the principles of modern centrifuga-tion and when centrifugal engineers better understand the refinery emulsion problems. It is not generally realized that centrifugal force and gravity have two distinct functions: First, subsidence wherein the suspended globules are brought into contact; second, coalescence (when this is possible) by rupturing the films around the globules. In the case of a water-in-oil emulsion, an exercise of the former function alone would yield: (1) oil, free, or as free as desired, from water; and (2) a concentrated water-in-oil emulsion—concentrated in the sense that it contains a relatively large percentage of the internal phase. An exercise of both functions will yield: (1) water-free oil and (2) oil-free water. Centrifugal force is much better than gravity for subsidence because, in the case of industrial emulsions where the suspended globules are visible under a microscope, subsidence is directly proportional to the force applied. Centrifugal force is only slightly better than gravity for coalescence. A minute trace of a proper reagent will immediately do more to nullify the interfacial surface tension opposing coalescence than an indefinite application of the highest attainable centrifugal force. No mathematical analysis has been made to explain the failure of high centrifugal force to induce a decidedly more rapid and more complete coalescence than is obtained by gravity. The adjustment of the centrifuge rotor depends more on the extent of coalescence that is desired or is possible than on any other factor. One reason for this dependence is to be found in the curious relation between the specific gravity and the hydrostatic pressure of emulsions. The continuous centrifuge works on the U-tube or Florentine flask prin-

Jan 1, 1924

By L. H Levenson, Charles S. Barrett

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.' Various methods involving etch pits have been used by other investigators. Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm's length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By Charles S. Barrett, L. H. Levenson

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.' Various methods involving etch pits have been used by other investigators. Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm's length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940