Search Documents

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1' and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,'' by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.'= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By Alfred H. Bell, George V. Cohee

In 1941 Illinois produced 134,139,000 bbl. of oil, or 9.5 per cent of the total for the United States, and ranked fourth among the states. The production for 1941 declined 9.2 per cent from the previous year's total of 147,647,000 bbl. Daily average production for 1941 was 366,000 bbl. At the beginning of the year daily production was slightly more than 326,000 bbl. and it remained at appoximately that amount until June, when there was a slight increase. The increase continued until the peak of 431,260 bbl. daily was reached for the week ending Oct. 4. Daily average production at the end of the year was approximately 387,500 barrels. The increased production during the last half of 1941 was largely due to the rapid development of the Johnsonville field, Wayne County, the Rural Hill field, Hamilton County, and the Benton field, Franklin County—new fields discovered in the current year (Fig' 1)—and the Woodlawn pool, discovered in 1940. Discoveries In 19 counties in southern Illinois, 44 new fields were discovered in 1941 (Fig. 2 and Table 2), and extensions to 40 fields were successfully completed (Table 3). At the end of the year there were 10,496 wells in the fields discovered since Jan. I, '937, as compared with 71965 wells at the end Of '940. The area proved for production in the new fields increased from 78,040 acres at the beginning of 1941 to 97,483 acres at the end of the year (Table I)—an increase of 19,433 acres, of which 9,955 acres are in the fields discovered during the current year, and the remainder of 9,478 acres in extensions to pools discovered earlier. Drilling During the past year, 3838 wells were completed in Illinois (Table 4), of which 2912 were oil producers, 13 were gas producers and 913 were dry holes; 76 per cent of the wells drilled were producers. Of the total number drilled, 591 wells are classified as "wildcat" and of these 84 (1 in 7) were successful in obtaining production. The results of an investigation to ascer-tain the reason for the locations of the wildcat wells are set forth in Table 5. Of the 591 wildcat wells, the 292 known to have been located by scientific methods were 21.6 per cent successful. The total footage of wildcat wells drilled in 1941 was 1,341,743 ft., of which a total of 216,995 ft. was drilled in successful wells. Exploration MEthods Subsurface geology and geophysics, largely the reflection seismograph, are still the principal methods used in exploration and development in the state. The number of seismograph parties operating throughout the year was as follows: seven parties on Jan. I, 1941; five on Apr. I; four On July I; eight on Oct. I; fifteen on Jan. 1: 1942.

Jan 1, 1942

By Alfred H. Bell, George V. Cohee

In 1941 Illinois produced 134,139,000 bbl. of oil, or 9.5 per cent of the total for the United States, and ranked fourth among the states. The production for 1941 declined 9.2 per cent from the previous year's total of 147,647,000 bbl. Daily average production for 1941 was 366,000 bbl. At the beginning of the year daily production was slightly more than 326,000 bbl. and it remained at appoximately that amount until June, when there was a slight increase. The increase continued until the peak of 431,260 bbl. daily was reached for the week ending Oct. 4. Daily average production at the end of the year was approximately 387,500 barrels. The increased production during the last half of 1941 was largely due to the rapid development of the Johnsonville field, Wayne County, the Rural Hill field, Hamilton County, and the Benton field, Franklin County—new fields discovered in the current year (Fig' 1)—and the Woodlawn pool, discovered in 1940. Discoveries In 19 counties in southern Illinois, 44 new fields were discovered in 1941 (Fig. 2 and Table 2), and extensions to 40 fields were successfully completed (Table 3). At the end of the year there were 10,496 wells in the fields discovered since Jan. I, '937, as compared with 71965 wells at the end Of '940. The area proved for production in the new fields increased from 78,040 acres at the beginning of 1941 to 97,483 acres at the end of the year (Table I)—an increase of 19,433 acres, of which 9,955 acres are in the fields discovered during the current year, and the remainder of 9,478 acres in extensions to pools discovered earlier. Drilling During the past year, 3838 wells were completed in Illinois (Table 4), of which 2912 were oil producers, 13 were gas producers and 913 were dry holes; 76 per cent of the wells drilled were producers. Of the total number drilled, 591 wells are classified as "wildcat" and of these 84 (1 in 7) were successful in obtaining production. The results of an investigation to ascer-tain the reason for the locations of the wildcat wells are set forth in Table 5. Of the 591 wildcat wells, the 292 known to have been located by scientific methods were 21.6 per cent successful. The total footage of wildcat wells drilled in 1941 was 1,341,743 ft., of which a total of 216,995 ft. was drilled in successful wells. Exploration MEthods Subsurface geology and geophysics, largely the reflection seismograph, are still the principal methods used in exploration and development in the state. The number of seismograph parties operating throughout the year was as follows: seven parties on Jan. I, 1941; five on Apr. I; four On July I; eight on Oct. I; fifteen on Jan. 1: 1942.

Jan 1, 1942

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale' defines clay as material finer than approximately 4 microns. Grim' has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By Ramesh Malhotra, Hubert E. (Deceased) Risser

THE WORLD Coal, as a source of energy and as a source of coke for the smelting of iron ore, has contributed significantly to the development of every major industrial nation of the world A number of other materials-oil, natural gas, wood, waste materials, water, and, in some applications, nuclear materials -can be used satisfactorily for the generation of heat and energy, but no generally acceptable and economic substitute has been found to supplant coke in iron ore smelting in conventional blast furnaces. In the development of many nations, coal provided the initial source of energy for industrialization Although coal provided more than 60% of the world's energy each year between 1902 and 1929, oil and natural gas have surpassed it as a source of energy in more recent years (Ref. 38, pp. 439, 441). Despite the rapid rise in importance of other fuels, a considerable amount of the total energy consumed is still supplied by coal. In 1972, coal supplied 32.1 % of the total world energy (Ref. 49, pp. 2-3). To produce this energy, 2.4 billion metric tons of coal were consumed-a 16.0% increase over the amount consumed in 1962. A further worldwide increase in the amount of coal used to supply energy is projected. According to Dr. Karlheinz Bund (Ref. 37, p 145), by the year 2000 world coal consumption could amount to 5 billion mt. Coal Resources and Production The world's coal resources are estimated to be about 10,872 billion mt. Of this amount, 1,297 billion mt are classified as measured reserves (Ref. 50, p. 57). In Table 13.A.1 the estimates of measured reserves and total resources, recent production, and the ratio of measured reserves to production of major coal-producing countries are shown. About 90% of the world's total coal resources are estimated to be in the USSR, the United States, and China. The United States ranks second in the world in coal resources, but in measured reserves, it ranks first. Because of the difference in rate at which available coal resources are being exploited, the ratio of measured reserves to actual production varies widely among areas and countries. France and East Germany have the lowest reserve to production ratios, 49.5 and 60.1, respectively. In Mexico, where currently less than 5 million mtpy of coal are produced, the ratio is 1257 For all countries producing more than 200 million mtpy of coal (except East Germany), the ratio ranges from 350 to 670. For the United States, the ratio is 669.7. In Table 13.A.2, distribution of the world's coal resources by area is shown. More than 97% of the total resources lie in the northern hemisphere, with Asia, including European USSR, having 63.4%. Only 1.9% of the total coal resources are estimat-

Jan 1, 1976

By F. L. Kadey

The petrographic microscope is a well known tool in nonmetallic materials research. Its utility in the study of perlite is, therefore, not surprising. Valuable information has been derived on samples smaller than those needed by most other methods of analysis. Relatively little has been written about the petrographic analysis of perlite for two chief reasons: perlite is a material of relatively new commercial interest; and the independent prospector or expander, responsible for most studies, attacks the problem from an immediately practical viewpoint. Hence, petrographic studies of perlite have been limited to academic aspects. Rapid development of commercial interest in perlite has changed the situation. Mining and expanding companies now have effective research tools; and such instruments as the petrographic microscope have added materially to practical knowledge about this mineral. Petrographic techniques employed in the search for suitable deposits screen worthless samples rapidly and inexpensively compared with large-scale expanding tests. Hence, only samples of potential quality are selected for further testing. Field appearance of perlite reveals little about its true identity and practically nothing about its commercial significance. Consequently, any method that can be used to separate the "wheat from the chaff" is valuable. In addition to the conventional thin-section and immersion methods used in evaluation of crude perlite, petrographic microscope techniques have contributed to the study of expanded perlite. When apparently similar materials behave as differently in use as perlites, the internal structure of the individual particles becomes a subject of great interest. The purpose of this paper is to discuss some of the petrographic techniques used to characterize this material. WHAT IS PERLITE AND WHERE IS IT FOUND? Perlite was at first described as a glassy rhyolite possessing a pearl-like luster and exhibiting numerous concentric cracks resembling an onion skin appearance.' Fig. 1 is an illustration of perlite in this classical sense. Recently, its definition has taken on a commercial connotation: an acid volcanic containing 2 to 5% of combined water that, when heated rapidly to the softening point of the glass, coincident with the volatilization of the combined water, expands or "pops". Fig. 2, although hardly fitting the classical description given by Johannsen, is an excellent perlite in the commercial sense. It may occur as a breccia in rhyolite, (Fig. 3) and sometimes it is associated with obsidian nodules, as illustrated in Fig. 4. The term perlite includes the expanded product also. In the United States, perlitic rocks are restricted to the western part of the country. 2 Elsewhere in the northern hemisphere, European occurrences follow a belt beginning in Iceland and extending in a southeasterly direction through Scotland, County Antrim in Northern Ireland, and through the Massif Central of France, Germany, and Hungary; thence, into Italy and Sardinia, and through some of the Aegean Islands. A general oriental belt extends from Japan through Australia and New Zealand. Rhyolitic areas elsewhere in the world undoubtedly contain perlite.

Jan 1, 1963

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.'s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations' and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.' GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By Fred C. Bond

COMPRESSION TESTS THE standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of crossectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a high-speed steel disk with diamond dust embedded in the edges, and running under a water spray. Such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding planes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing Co., and are listed alphabetically in Table 1. These tests were made on one inch cubes or on diamond-drill cores approximately one inch in diameter and one inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. Compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test No. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TVA quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1946

By E. J. Valyi

The purpose of the continuous casting processes is twofold: As the name implies, they aim at performing a heretofore intermittent operation continuously; in this respect, they tend to satisfy the appetite of the beast that modern extrusion plants and rolling mills have grown to be. The effort invested in the development of these methods bore rich dividends in economy and in the improvement of technical characteristics. The other purpose of many continuous casting methods is to reduce the number o-f operations mushrooming between the liquid alloy and the finished mill product, essentially by substituting adequate chill in comparatively small cross sections for one or more "breakdown" steps. It is this second tendency of continuous casting that justifies description of the Soro process within the frame of our symposium: although not continuous, the Soro method constitutes a means of converting molten metal into a nearly finished mill product. The Process The name, Soro, is a composition of initials and abbreviations, with no particular technical significance. The process originates in Switzerland; it was adopted by numerous European plants between 1937 and 1940 and is now being installed in this country. It is applicable to ferrous and nonferrous alloys of an exceptionally wide range of composition. It is capable of producing rod from 1/2 in. to approxi- mately 4 in. in diameter, or other simple solid shapes of corresponding cross-sectional area. , Fig. I shows schematically the succession of operations involved. A ring is cast in a two-part centrifugal-casting metal mold. The cross section of the ring may be round, hexagonal, rectangular or some other solid shape, with the exception of any contour that is undercut with reference to the mold parting line. As cast, the ring has a riser along its inner periphery, which is removed in the next operation, so as to leave the ring with a dean cross section. Following the removal of the riser, the ring is severed at one point and one end is bent outward, leaving a slight clearance between the two ends. The next step is straightening of the ring in a special device, forming a bar with a slight bend; this is followed by any one of the conventional finishing operations that are necessary to obtain forging rod, screw-machine stock or strip. The outstanding features of this procedure are: I. The cross section cast is the same or within a few per cent of the cross section of the finished product (except for fabricating into strip and wire). 2. All operations following casting of the ring are performed cold. Equipment The equipment required is simple and inexpensive. The casting machine is a conventional horizontal-shaft mold assembly, similar to those found in centrifugal-casting foundries. Fig. 2 shows a battery of three machines- with their protecting hoods .swung open. One of these machines,

Jan 1, 1945

By V. V. Valleroy, A. J. Cornelius, B. T. Willman, G. W. Runberg, L. W. Powers

This paper reports the results of an investigation into the use of steam as a recovery agent. High oil recoveries by steam, as much as 100 per cent greater than by water flood, were demonstrated in laboratory linear cores. The principal mechanisms responsible for the additional oil have been identified as (1) thermal expansion of the oil, (2) viscosity reduction and (3) steam distillation. Although the first two also enhance recovery by hot water flood, they are effective with steam injection at lower volumes of produced fluids. Steam-zone residual oil saturation is independent of initial saturation. Recovery by steam is greater for lighter oils because they contain a greater fraction of steam-distillable components. Equations for the steam-zone advance in a radial homogeneous system are presented; these show the effect of reservoir parameters. The displacement in the hot liquid region moving ahead of the steam front can be estimated by a calculative procedure which is suggested. The method which takes account of the temperature gradient is applicable also to a regullar hot water flood. INTRODUCTION Considerable industry interest in the application of heat to petroleum reservoirs as a means of increasing oil recovery has been evident in the past few years. Three thermal methods which have attracted interest are (1) the injection of saturated steam, (2) the injection of hot water and (3) the injection of air into a formation to support combustion within the reservoir. Much has been published in recent years on underground burning, and there have been several papers on hot water injection. Although there are several early reports1,2 on steam injection, no recent experimental studies have been published on this recovery method. In our early thermal methods research, a marked improvement was found in oil recovery by steam injection compared with recovery by water injection in the same system. An investigation subsequently was undertaken to obtain quantitative information from which to evaluate steam injection as an oil recovery method. In addition, it was desired to investigate the recovery mechanism of hot water as compared with that of "cold" water and steam injection. An understanding of the mechanisms by which these processes operate would generally define favorable field conditions for their successful application. This paper reports the results of the laboratory study and suggests calculative approaches to estimate the field behavior of the steam-injection process. EXPERIMENTAL METHOD EQUIPMENT A schematic diagram of the equipment used for the displacement tests is shown in Fig. 1. Essentially, it consisted of a core with suitable means for recording temperatures, a feed system for injecting steam or cold or hot water, and a receiving train for condensing, cooling and measuring produced fluids. For the steam experiments, air-free saturated steam was piped from the boiler to the core face in insulated lines that were provided with steam traps and bleeds to remove any condensate formed in the lines due to heat losses. A 12-in. section of the line immediately ahead of

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By Donald W. Scott, L. A. Roe, B. J. Sweo

INTRODUCTION THIS paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizers and organic dyes, and 35 parts of water are added to loo parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder' in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the overspray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1947

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By Toshimi Yamane

The internal friction of cold-worked titanium iso-thermally annealed at temperature below the recrystallization temperature was measured. The internal friction was calculated from the half width of a resonance curve of the specimen which was vibrated transversally by the electromagnetic method. The experimental results were as follows: 1) The specimens annealed for a long time at temperature below the re crystallization temperature after cold working have the strain-amplitude dependent internal friction. 2) The internal friction increased by the cold working was decreased during the isothermal annealing. The reason of decrease of the internal friction is considered to be caused by the annihi-lation of lattice defects. 3) There is a linear relation between logQt-1/Q0-1 and (1/T)2/3 below the recrys-tallization temperature, where Q0-1 is the internal friction standing 24 hr at the room temperature after cold rolling, Qt-1 is the internal friction annealed at T°K for t min. 4) The hardness of the cold-worked titanium does not change by the annealing at 300°C for a long time but decreases by annealing at 400ºand 460°C. METALS, when cold worked, show sharp changes in physical and mechanical properties' The internal friction of cold-worked metals increases sharply and has a maximum value1,2 connected with working de- grees. The increased internal friction of cold-worked metals is recovered by annealing. This phenomenon is the well known effect called Köster effect. The recovery of the internal friction occurs earlier than the changes in tensile properties, hardness, or X-ray diffraction, and is very sensitive to the structure of a metal. The mechanism of the recovery at a temperature lower than the recrystallization temperature is being considered variously by many investigators: there are such views as the annihilation of dislocations by smith,' the rearrangement of dislocations mentioned by Nowick,4 and interaction of dislocation with point defects.5 Smith and Nowick also considered the interaction but it is so difficult for them to explain the rearrangement mechanism systematically, it being not considered a special model; therefore, we do not explain it quantitatively. Experiments measuring the recovery of the internal friction of cold-worked metals were performed by Gordon and Nowick6 on NaCl, and by Smith on copper. In addition, there are many studies, particularly those of measurements on copper by other investigators. There are comparatively many investigations on aluminum and iron which are the cubic system,'-' but only a few on metals of the hexagonal system.10 In view of this, I investigated cph titanium at room temperature and measured the internal friction after annealing isothermally at temperature lower than the recrystallization temperature. SAMPLES AND EXPERIMENTAL METHOD samples for the experiment were cut from a 6-mm titanium plate. The long direction of samples was

Jan 1, 1963

By P. Rama Rao, D. H. Sastry, T. R. Anantharaman

Deformation (a) and twin (a') stacking-fault densities in cold - wor ked filings of fcc silver alloys containing 2, 4, and 6 wt pct Sb have been estimated from Debye-Scherrer peak shifts and asymmetries, respectively. Evidence has been obtained for a possible strain-induced transformation in a two-phase alloy containing 9.0 zut pct Sb. Using Fourier analysis of X-ray line profiles, the effective particle sizes and root mean square strains have been determined for the three fcc alloys in the cold-worked condition. The values of the compound fault probability 0.5a + a') evaluated from peak shifts and asymmetries are in reasonable apeement with those derived from peak broadening. COLD work of fcc metals may produce both deformation and twin (also called growth) stacking faults, which can be detected and quantitatively estimated by X-ray diffraction techniques.' In addition to peak broadening, deformation faults produce a shift in peak positions and twin faults an asymmetry of the Debye-Scherrer reflections. Besides stacking faults, a reduction in the size of coherently diffracting domains and distortion within these also broaden the powder reflections of deformed fcc metals and alloys. Fourier analysis' of peak shapes provides quantitative infor- mation about the effective domain sizes, lattice strains, and also the compound fault probability (1.5a + a'), where a and a' represent deformation-and growth-fault density, respectively. The Paterson method2 for determination of a from peak shifts, the warren3 or wagner4 method for evaluation of a' from peak asymmetries, and the Fourier analysis for quantitative estimates of all the contributory causes of peak broadening have, in the course of the last decade, been extensively applied to obtain data for a number of deformed fcc metals and alloys. One of the useful results of earlier measurements of a in several solid solutions is a correlation between a and the solute valence as well as electron concentration per atom (p) in alloy systems based on a particular solvent. The work of Smallman and westmacott5 on Cu-Zn, Cu-A1, and Cu-Sn, of Foley, Cahn, and ~aynor' on Cu-Si and Cu-Ge, and of Rama Rao and Anantharaman7 on Cu-Si and Cu-Sb has revealed a common trend in the increase of a with p and also a with valency of the solute. Cahn and Davies' and Ad-ler and wagnerg have observed similar trends for silver alloys containing cadmium, indium, and tin. Data on a for silver alloys with a pentavalent solute element are not, however, available. It is primarily to fill this need that the present investigation on Ag-Sb alloys was undertaken. Utilizing the Patersonand Warren methods, values of a and a', respectively, have been determined in three silver alloys containing 2, 4, and 6 wt pct Sb. By Fourier analysis of the broadening of Debye-Scherrer peaks, effective particle sizes, lattice strains, and the compound fault probability (1.5a +a') have also been evaluated.

Jan 1, 1967

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Table I (Jones, 1973) affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 (Anon., 1967) is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak-type brines, produced mainly for lithium. Market Attributes Some of the important market traits common to industrial minerals used by the chemical industry are listed below. 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. For example, fluorspar from China and Thailand normally goes to Japan, while South African fluorspar can go either to Japan or to the US. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities.

Jan 1, 1983

By K. E. Brown, F. W. Jessen

It is deemed feasible to store atomic reactor fuel wastes in salt dome cavities when the differential pressure acting on the cavity does not exceed 3,000 psi and the temperature is less than 400°F. Tests at pressure increments of 1,000 psi were conducted on a 2-in, cylindrical cavity contained in a 6-in. long X 6-in. diameter salt core. The cavity exhibited stability under pressures up to 3,000 psi and temperatures to 300°F. At temperature ranges of 100 to 400°F and with pressures of 5,000 psi and above continuous deformation of the cavity resulted. Initial movement of the salt was observed at all pressares. This was evidenced by vertical deformation and cavity size reduction. INTRODUCTION The development of storage techniques for safe disposal of atomic reactor fuel wastes is a goal of the Atomic Energy Commission. Salt domes have been used successfully for storage of liquefied petroleum gases and hence should prove to be suitable for liquid waste products of atomic reactors. The purpose of the following work is to evaluate the practicability of utilizing salt dome cavities for such wastes and to de-termine particularly the effect of pressure and temperature on a salt cavity. This work represents a part of a comprehensive study covering the over-all problem of storing re- actor fuel wastes in salt domes and/ or salt beds. The problem of accurately determining the stresses which exist in rocks in the earth's crust is indeed a complex one. Theoretical studies have differed widely in many of the basic assumptions about the physical properties of the rock itself. Some solutions of problems in underground stress analysis assume that rock is elastic, homogeneous and isotropic in character; others assume that rock possesses plastic, viscous, elasticovis-cous properties, or a combination thereof. Experimental evidence has shown that salt possesses plastic, viscous and elasticoviscous properties.' Recent work has shown that salt becomes more plastic with temperature.' APPARATUS AND PROCEDURE For experimental study a cylindrical cavity was chosen for analysis since it provided maximum volume per unit of depth with constant diameter. This particular cavity shape, allowing for irregularities, can be easily leached out of salt domes in field operations. For the purpose of approaching underground storage conditions as nearly as possible, the following factors were considered: (1) control of pressure and temperatures, (2) measurements of temperature gradients throughout salt mass, and (3) measurement of structural stability of salt cavities. In order to obtain triaxial pressure on the salt cavity without resorting to the application of fluid pressure directly on the salt mass, a system was designed whereby the same effect could be produced through axial loading only. By cutting a core to close dimensions to fit a steel test cylinder and applying axial pressure, a lateral pressure was obtained. This equipment is shown in Figs 1 and 2. A steel cylinder was made from

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952