Search Documents

By Stephen Royce

[PAGE Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine (TP 2000 by JOHN W. VANDERWILT, Min. Tech., May 1946. Discussion by STEPHEN ROYCE and the Studies of the Design of Shaped Explosive Charges and Their Effect in Breaking Concrete Blocks (TP 2157 by GEORGE B. CLARK, Min. Tech. May 1947. Discussion by PHILIP B. BUCKY, V. H. CLARK, E. D. GARDNER, M. H. HAWKINS, H. L. WALKER, and the author) 2 See TP 2377, Min. Tech., May 1948 for discussion of San Manuel ProsPect (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the authors)] Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine STEPHEN ROYCE•-It is interesting to note from B, Fig 2, how closely the subsidence limits approximate to the 60° angle of draw, which is so commonly found to rule in large scale rock subsidence. The tension cracks shown at B are commonly found in the initial stages of subsidence movement and spread like a halo about subsidence limits as movement extends. These tension cracks usually grow into escarpments later on. Apparently from the illustrations and description given, a system of vertical fractures is the predominating weakness in the wall rock at Climax, and therefore both tension cracks and escarpments are prevailingly vertical in attitude. The illustrations in Mr. Vanderwilt's article seem to conform to the general rule that yield by subsidence is heralded by tension cracks which foreshadow the appearance of the subsidence scarps which are both described in the paper and shown in Fig 2. The difference between the B side and the A side of Fig 2 is apparently caused mainly by the vertical fracturing which controls subsidence at Climax as compared to the relatively homogeneous rock formation at A upon which the original figure in Peele's Handbook was based. The draw at B is exactly 60°, while the draw at A is a little flatter. The influence of the vertical fractures explains the difference. The surprising feature is the relatively small deviation from the general 60° draw line, which is about the average of rock subsidence experience. The influence of local fracture systems, faults and bedding in controlling subsidence all the way from extremely low angles of draw to vertical is rather fully discussed in the Peele's Handbook article referred to. The more illustrations of subsidence there are published the better will be our knowledge. The general principles are pretty well established. The wide local differences reflect the effect of local conditions. This paper is a very valuable contribution to the subject, and for the benefit of the mining industry, it is to be hoped that there will be many more such clear and concise presentations. Particularly block caving is apt to be of greatly increasing importance in the future of a mining industry that must meet high labor costs. More examples of block caving from small scale to large scale operations like those at Climax will serve a vital need. JOHN W. VANDERWILT (author's reply)-I would like to thank Mr. Royce for his discussion; however, in his comments the meaning of subsidence, draw and tension cracks is not entirely clear. As used in my discussion of subsidence at Climax, subsidence refers to movements involving appreciable downward displacement. Tension cracks indicate only

Jan 1, 1947

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE existence of v phase in the Mn-Mo system was discovered in this laboratory several years ago,' but neither the conditions of its formation nor its composition were known, and preliminary attempts to reproduce the phase were unsuccessful. We wish now to specify the information appropriate to phase formation on the basis of experiments performed since that time. The starting materials were in every case electrolytic manganese and high purity molybdenum. Two methods of preparation were employed: l—arc-melting varying combinations of the elements in an inert atmosphere and subsequent heat treating, and 2—sintering compressed mixtures of finely divided powders of the elements. In the latter method, the powders were first passed through 200 mesh screen and then compressed into cylinders of % in. diameter and % in. length, which were sintered at elevated temperatures in an atmosphere of dry hydrogen. For some samples, the sintering temperature was 1200°C (for 1 hr), and these were then heat- treated at lower temperatures for times up to 24 hr. Eventually it was found, for the proper composition, that essentially pure a phase could be produced by sintering at 1125°C for 3 hr. Quenching to room temperature was effected by means of a stream of cold, dry hydrogen in a water-cooled chamber. The arc-melting procedure was found to be unsatisfactory after an investigation of many samples at different compositions and temperatures. Large quantities of manganese were vaporized during melting and none of the products were homogeneous or contained extended regions of pure phase. Nonetheless, these experiments established that no formation occurs in the Mn-Mo system below 1115oC, and indicated, at least roughly, the composition range of interest for further exploration. The more definite results obtained from samples produced by the second method are given in Table I. A portion of sample 2 heated for 16 hr at 1000°C in a Vycor tube transformed to molybdenum plus unidentified phases of complex X-ray pattern. From these few results it appears that the region of phase is quite narrow in composition. It is of interest that the composition is such as to make for difficulties in correlating this structure on an electron atom basis with other a structures of iron, cobalt, and nickel. In that respect Mn-Mo shows the same anomaly as Mn-Cr and Mn-V systems.' A second feature is that in common with the two other known molybdenum (Fe-Mo and Co-Mo), Mn-Mo v exists only at elevated temperatures. The X-ray powder pattern of the pure a phase of Mn-Mo is given in Table 11. It agrees well with the patterns established for other structures, especially with that for Fe-Mo as given by Goldschmidt.An attempt is being made to establish whether an ordering of the respective atoms occurs and such information will be reported in a future publication. Acknowledgment The authors acknowledge gratefully the assistance of Mrs. J. R. Belanger in some portions of this work. References 'J. S. Kasper, B. F. Decker, and J. R. Belanger: Journal of Applied Physics (1951) 22, p. 361. 2 A. H. Sully: Journal Inst. Metals (1951) 80, p. 173. H. J. Goldschmidt: Research (1949) 2, p. 343.

Jan 1, 1954

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By N. J. Grant, C. F. Flo, F. B. Cuff

An investigation of the Ti-Cr system has shown the presence of a complete series of solid solutions in the ß phase, with a minimum in the solid us near 50 pct Cr. An intermetallic compound, TiCr2, forms during cooling from the ß solid solution. There is a eutectoid reaction at the low chromium side of the system. IN view of the recognition of the potentialities of titanium and its alloys as important structural materials there has arisen a need for a systematic investigation of various titanium binary diagrams. Of these, the Ti-Cr system was of particular interest because of the improved properties imparted to titanium by small chromium additions. A literature survey disclosed a partial constitution diagram that had been suggested by Vogel and Wenderott,¹ This diagram, shown in Fig. 1, is the result of work done on the Fe-Cr-Ti ternary system. Alloys containing less than 43 pct Cr were not investigated. In addition to this, a study of alloys in the Ti-Cr system was reported by McPherson and Fontana.² Adenstedt3 furnished a number of dilato-meter curves obtained from specimens containing 5, 10, and 15 pct Cr. Very recently, McQuillan4 submitted a proposed diagram covering the complete range of compositions between titanium and chromium. This diagram was in general agreement with the one described here. Experimental Procedure Sponge titanium (99.7 pct) and electrolytic chromium (Bureau of Mines analysis: 99.03 pct Cr, 0.40 pct Fe, 0.53 pct O2) were used for the initial determination of the system. Subsequent refinement of points, particularly for the low chromium side of the diagram, was accomplished by using iodide titanium and high purity chromium (National Research Corp. analysis: 0.050 pct C, 0.045 pct O2). The Ti-Cr alloys were prepared by melting 25 g charges in an enclosed, water-cooled copper crucible using a movable tungsten electrode. The atmosphere was helium, prepurified by first passing it through a drying agent and then through sponge titanium heated to 850°C. Particular care was taken to avoid any large scale segregation resulting from insufficient mixing of the components. Each charge was melted and kept molten for approximately 1 min, allowed to cool, inverted, remelted, and kept molten for an additional minute. In order to ascertain the amount of impurity pickup (oxygen and nitrogen) during the melting procedure, three iodide titanium specimens were melted in sequence and then checked for increased hardness. The specimens in the as-cast condition showed a relatively large hardness increase over the hardness of the as-received iodide titanium. The scattering on these readings was large. However, after the specimens had been homogenized at 840 °C for 2 hr and slowly cooled, the measured increase in hardness over the as-received titanium was small with a corresponding decrease in scatter. The reason for this hardness change is that in heat treating these specimens below the transformation temperature (885°C) there was a conversion from the as-cast structure to the more nearly equilibrium structure of the annealed specimen. The alloys were analyzed for chromium content and although the actual percentage was invariably low the deviation from the nominal composition never exceeded 0.6 pct Cr.

Jan 1, 1953

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By A. D. Schwope, L. R. Jackson, A. M. Hall

In the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of re-crystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. Materials Used in The Investigation Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table I. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871° C in air and hot rolled to % in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hr. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pet reduction) in 6 passes and annealing at 427'C for 4 hr. This annealed wire was then drawn to 0.081 in. wire, (37.1 pet reduction) in 2 passes. Square rod was made by hot rolling wire bars to Re in. rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 346 hr at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°Cf or 3 1/2 hr Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 x 0.268 in. square, annealing for 3 1/4 hr at 538°C and cold rolling to 0.257 x 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hr in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from o.o15+.oz5 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. Effect of Cold Drawing and Tensile Strain on Strength of Copper Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are 6

Jan 1, 1949

By W. W. Krysko

In order to calculate the critical particle size of lead oxide entrapped in lead, Stoke's Formula may be applied. All data were available except figures for the density of lead oxide at elevated temperatwes. The density of lead oxide was determined by means of dilatometmetrc and volumetric methods up to 1010°C. Graphs of the density of lead and lead oxide as well as the viscosity of lead are given and discussed, with the conclusion that the most unfavorable region for the separation of lead oxide from molten lead lies just above the melting point of lead. DURING previous investigations, particularly on the dedrossing of lead with aluminum1 and the oxygen solubility in lead,' the critical particle size of lead oxide which could be entrapped in solidifying lead was estimated by calculation, and it was shown that high values found for the oxygen content of lead may be due to the method of sampling and the entrapped particles of dross. Unfortunately, due to lack of data, an exact mathematical solution was not possible. The particle size which will separate under a given condition can be estimated from Stoke's Law, which states that where: d = diameter of the critical particle size ¦q = viscosity of lead in Poise V = constant velocity in cm sec-I g = 981 cm sec-2 61= specific gravity of lead 62= specific gravity of lead oxide The depth of the lead bath and the time before solidifying define the velocity. The viscosity of molten lead is known from earlier work by Krysko and is given in Table I. The specific gravity of lead is also known, see Table II. These values are according to Hofmann. A careful survey of literature revealed no values for the density of lead oxide at elevated temperatures. The present investigation was therefore conducted to provide this information. RESEARCH INVESTIGATIONS The density of lead oxide was determined from the following experiments: 1) Determination of the density of lead oxide at room temperature. 2) Dilatometric investigations on the same samples. 3) Determination of the shrinkage at the liquid-solid trans£ormation. 4) Density determinations on liquid lead oxide. 5) Time temperature curves during cooling. 1) The samples for the determination of the density of lead oxide in the solid state were prepared in the following manner. Molten lead oxide was cast into I hot mold which could be opened along the longitudinal (vertical) axis. The cast samples were cylinders of approximately 10 mm diam and approximately 80 mm length. The cylindrical hot mold was open at both ends and was placed on a large copper chill plate shortly before casting. The solidification of the lead oxides proceeded upwards without any formation of internal cavities. The sample was carefully checked with respect to density and crystalline appearance, and only the lower portions which were crystalline and free from porosity were used. The density was determined in a specially made pyknometer-like container, where the surplus liquid was squeezed out through an orifice approximately 1/10 mm in diameter. Mercury or water was used as the liquid. The densities of the samples were calculated from the weight, volume, and mean specific gravity of eight samples was 9.62 * 0.05 g cm"3 at 22"~. 2) The samples were machined to approximately 1 1/2 in. in length and fitted into a dilatometer. A

Jan 1, 1962

By J. Kucera, J. Vreštál

DIFFERENT authors1 ' have been engaged in meas-uring the vapor pressure of pure cobalt. The results of their measurements satisfy the expected temperature dependence of vapor pressure and are in mutual agreement, with the exception of the results by De Dyk Man and ~esmejanov.~ The latter authors, by using the effusion method, have achieved considerably higher values than other workers. By using the isotope exchange method they obtained much lower values than other authors. The determination of thermodynamic functions of the binary Ni-Co system was carried out, as far as we know, only by De Dyk Man and Nesmejanov.4 This determination was based on extremely low values of vapor pressure over pure cobalt obtained by the isotope exchange method. Therefore we considered it useful to repeat these measurements. Furthermore, the reliable values of thermodynamic functions should complement the migration characteristics, the inner magnetic field data obtained by Miissbauer effect measurements, specific heat data, and the K effect and positron annihilation characteristics that have been achieved for the Ni-Co system in the Institute of Metallurgy of the Czechoslovak Academy of Sciences in Brno.5-9 The measurements in this paper were performed by the isotope exchange method. In this method, as has been shown by analysis,10-'3 the vaporization rate, w, can be calculated from the relation w = k/1oSw [1] i0Sw) [1] where L, is the activity per unit mass of the source, S is the area of evaporation, k is the tangent at the point t = 0 to the curve giving the radioactivity de-pendence of the target vs annealing time, t, and wis the probability for the tracer atom condensation on the target surface. The value for cc. can be obtained from the equation w = a + 2P(l-a) [2] where P is Clausing's coefficient and a is the condensation coefficient. In the present work the cylinder shaped containers for annealing the samples were used, characterized by the ratio 1:d = 1.06. Here 1 is the length and d the diameter of the container. For this ratio P = 0.514 and w =0.5, and w is independent of the condensation coefficient. The vaporization rate is related to the vapor pressure p by the relation where R is the gas constant, T is the absolute temperature, and M is the molecular weight of the component investigated. Measurements of the vapor pressure of the i component over the pure metal, p!, and the alloy, pi, at the given temperature and composition enable one to calculate the thermodynamic activity of this component from the equation ai=pi/pi [4] is and the activity coefficient ri=ai/xi [5] xi where xi is the molar fraction of the investigated alloy component. EXPERIMENTAL Evaporization rate measurements were carried out with pure cobalt and eight different Ni-Co alloys, which were kindly delivered by the Centre National de Recherches Me'tallurgiques Liege, Belgium. The composition of the alloys is given in Table I. The cobalt used in these alloys contained the following impurities: 0.016 wt pct Fe, 0.014 wt pct Cu, 0.01 wt pct Mn. Other elements were present in much lower concentrations. From the melts, samples in the form of small cylinders of 12 mm in diam were ma-chined. The thickness of the targets and sources was 2.5 and 1.2 mm, respectively. The lower thickness of the sources was chosen to make their over-all ac-tivity as low as possible. Sources were activated in

Jan 1, 1970

By J. W. Cunningham, W. A. Tiller, D. H. Lane

The effect of ultrasonic vibrations on ingot solidification has been considered both theoretically and experimentally. The theoretical section elucidates the mechanisms by which the ultrasonic vibrations might refine the ingot structure. The experimental section describes a very efficient means of introducing the ultrasonic vibrations to the freezing interface. The application of this technique to the consumable-electrode arc melting process shows that the columnar mode of freezing may be effectively suppressed yielding an ingot structure consisting predominantly of equiaxed grains. The results support the contention that the ultrasonic vibrations increase the nucleation frequency in the layer of liquid adjacent to the freezing interface. CERTAIN structural characteristics of as-cast ingots are undesirable since they create considerable difficulty for subsequent processing and often produce defects in the finished product. These structural defects are illustrated in Fig. 1(a), and are: 1) planes of weakness where columnar grains growing from the different mold faces meet, 2) strength anisotropy due to the preferred orientation of the columnar grains and 3) inhomogeneity due to segregation at dendrite boundaries within the columnar grains and at the columnar grain boundaries. The type of ingot structure that eliminates 1) and 2) and diminishes 3) is the fine-grained equiaxed structure illustrated in Fig. 1(c). Many attempts have been made to produce the desirable ingot structure illustrated in Fig. 1(c) by inoculating, casting with varying superheats, vibrating or stirring, or by irradiation with ultrasonic vibrations. These attempts have met with various degrees of success, the ingots generally having the structure illustrated in Fig. 1(b). All four methods have been the subject of numerous investigations,1"4 the latter producing the most erratic behavior and inconsistent success. The method of ultrasonic irradiation during ingot solidification has shown considerable promise on small-scale ingots (diam 2 in.) but has not yet been successfully adapted to large-scale operation. The present paper considers the application of ultrasonic radiation to ingot solidification both theoretically and experimentally. The purpose of the paper is to elucidate the mechanism by which ultrasonic energy refines the ingot structure and to describe a method for producing the desirable ingot structure in both laboratory scale experiments and in ingots of commercial size. THEORY Conventional Casting—Before discussing the possible effects of ultrasonic radiation upon ingot structure let us first briefly review the reasons for the breakdown of columnar crystallization to equiaxed crystallization during ingot solidification. The following is a slightly oversimplified description. In the conventional method of casting, the alloy having a certain degree of superheat, T, is poured to fill a cold mold which is at room temperature, Tc,. Due to conduction of heat through the mold wall the outer rim of liquid metal cools rapidly to the liquidus temperature and begins to supercool. At some degree of supercooling, nuclei of solid form at random in this supercooled layer at the mold surface. The grains in this chill layer begin to grow inwards producing a solute build-up, thus lowering the freezing temperature at the interface as illustrated in Fig. 2. As growth proceeds, the temperature gradient in the solid conducts away not only the latent heat of fusion evolved during growth but it also conducts away some of the superheat of the melt so that the temperature

Jan 1, 1961

By C. F. Weinaug

In recent years, several methods have been proposed for correlation of physical properties and behavior of hydrocarbon systems. These correlations were found to be unsatis. factory for predicting differential gas liberation and shrinkage data now obtained experimentally. To achieve the desired accuracy, methods were developed to adjust the correlations with two experimental pieces of data. The required data are the saturation pressure at reservoir temperature and the specific volume or density at these conditions. The saturation pressure is used to adjust the vapor-liquid equilibrium-ratio correlations. The density measurement is used to determine the apparent density of liquid methane. With these adjustments, differential gas liberation and shrinkage are predicted within the experimental error. EQUILIBRIUM RATIOS Equilibrium ratios published by the National Gas Assn. of America' were used as a basis for the calculation. The convergence pressure for the sample was determined by using a hypothetical binary system, with methane as one component and the remainder of the system lumped together to form the other component. For the critical temperature of the heavy constituent, the weight average of the critical temperatures of the ethane and heavier components was used. The correlation of pseudo-critical temperature, density and molecular weight of Matthews, Roland and Katzl was used in this calculation for the hexane and heavier fractions. Points for the critical properties of methane and the hypothetical heavy constituent were placed on a chart of the critical loci of hydrocarbon systems. A critical loci for the hypothetical binary system was drawn, and the critical pressure of this system was determined at the reservoir temperature. This critical pressure became the convergence pressure for which equilibrium ratios were read from the NGAA4 charts. The NGAA equilibrium constants for C, through C, were used for the C,; through C, fractions since they were separated on the bases of normal paraffin boiling points. The correlation of Hoffman, Crump and Hocott5 as used to estimate the equilibrium constant for the C fraction. The NGAA eauilibrium-ratio charts are based primarily on paraffin systems and have to be corrected for the presence of naphthenes and aromatics. The correlations in the literature proved too unsatisfactory for determining these corrections. EXperimental data, the saturation pressure, is used with the correlation of Soloman2 to make this adjustment. The correction factors of Soloman were cross-plotted so that the factors for ethane and heavier components were made a function of the factor for methane. a2 = 0.7927 at + 0.1646 .........(1) where a, = correction coefficient for for methane NGAA equilibrium ratio, and a2t = correction coefficient for ethane and heavier NGAA equilibrium ratios. This equation and the equation for the bubble point are solved simultaneously for the correction coefficients. The bubble-point equation is anKnXn = 1.0 . . . . (2) The equilibrium constant for the saturation pressure at reservoir temperature is used. This procedure not only corrects for the relative volatility between components, but also assures that the results will be directly related to the experimental saturation pressure. METHANE DENSITY After determining a set of equilibrium ratios, the apparent density of condensed methane at 60°F and 14.7 psia was estimated. This was found to be necessary because the correlations of Standing3 ere found to be unsatisfactory. The law of additive volumes was employed to make this calculation.

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker's etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By J. Chipman, N. J. Grant, J. C. Fulton

This paper contains data on the distribution of silicon between liquid iron-silicon-carbon alloys saturated with respect to graphite and CaO-SiO2-Al2O3 slags under 1 atm of CO at 1600°C. The ranges of slag compositions studied were extended from the dicalcium silicate saturated liquidus composition up to silica concentrations at which Sic appeared as a stable phase. IN blast furnace operation it is not to be expected that slag and metal reach equilibrium with one another. Nevertheless, the silicon content of the metal varies with slag composition and with temperature in a manner which would be predicted from equilibrium considerations. Similarly, the distribution of sulphur between slag and metal does not attain an equilibrium state, yet the influence of slag composition is strongly analogous to its effect on the distribution equilibrium. The desulphurizing power of metallurgical slags has been shown to be highly dependent upon the FeO content of the slag. Moreover, the rate of removal of sulphur from slags is influenced by the oxygen potential of the slag-metal system. Thus it was shown by Grant, Kalling, and Chipman1 that the presence of MnO in slags which are low in FeO causes a marked slowing down of the transfer of sulphur from metal to slag. This led to the hypothesis that the slow removal of sulphur by blast furnace slags of more acid composition might be due in part to the effect of SiO2 on the oxygen potential of the system. This was verified in the work of Grant, Troili, and Chipman,' who found that the desulphurizing power of the more acid blast furnace slags could be markedly improved by an increase in the silicon content of the underlying metal. Their explanation of this improvement was that the higher silicon content of the metal decreased the rate of transfer of more silicon and, along with it, of oxygen from the slag to the metal. The slowness of the transfer of sulphur from metal to slag was the result of the slow reduction of SiO2 from slag to metal. Attempts to study the rate of sulphur removal had in the past resulted in very slow rates corresponding to the rates of silica reduction. It has become evident on the basis of these studies that further experimental studies on the rate of removal of sulphur must take these factors into consideration if there is to be a clear understanding of the rate of sulphur transfer under conditions simulating those existing in the blast furnace. It will be necessary, at least in a part of such study, to employ combinations of slag and metal in which the disturbing effect of silica reduction has been eliminated; in other words, to employ slag-metal combinations which are already in equilibrium with respect to the transfer of silicon. In preparation for such studies of desulphuriza-tion, a preliminary program of research on the distribution of silicon between slag and metal has been undertaken. This will ultimately include a comprehensive survey of the effects of temperature and slag composition on the equilibrium distribution of silicon between slag and metal. The present paper is a report on experimental methods employed and on

Jan 1, 1954

By W. D. Forgeng, R. E. Grace

The rate of copper corrosion in liquid lead was studied as a function of flow rate and temperature in a closed isothermal loop system between 350" and 500°C. Kinetic data were interpreted with the Nernst-Brunner equation and the Chilton-Colbum mass transfer analogy to heat transfer. Over the range of temperatures and flow rates employed the solution rate constant varied from 2 x 10-3 to 20 x 10-3 cm per sec. The rate constant was found to vary with the 0.76 power of the Reynolds number in the range 7500 < Re < 40,000. The results of this investigation indicate that the Cu-Pb corrosion process is controlled largely by diffusion across a boundary layer. particularly at the higher temperatures. The effective boundary layer for diffusion is found to be approximately three to four times smaller than the momentum boundary layer. CORROSION by liquid metals has long been a problem during melting, static containment, and casting. Recently, considerable emphasis has been placed on the understanding of liquid metal corrosion mechanisms in an effort to prevent mass transfer and eventual failure in liquid metal heat exchangers and in liquid-metal-fueled nuclear reactors. The present investigation was conducted to determine the relationships which exist between corrosion kinetics and hydrodynamic conditions in an isothermal loop containing a simple liquid metal-solid metal corrosion system. The Cu-Pb system was chosen for its simplicity and ease in handling. Previous isothermal Cu-Pb corrosion studies1-3 have been conducted in both static and dynamic systems but not under conditions which allow easy "scale-up" to engineering systems, such as liquid metal heat exchangers. On the other hand, most liquid metal loops which have been used to evaluate mass transfer rates4 have been driven with temperature gradients under conditions of natural convection and unknown flow rates. The primary contributions of this research are twofold: 1) to evaluate the design of a simple isothermal loop corrosion system and 2) to investigate liquid metal corrosion behavior under well-defined hydrodynamic conditions. MATERIALS AND EXPERIMENTAL WORK The apparatus used to measure the Cu-Pb corrosion rates is shown schematically in Fig. 1. The loop system consisted of 1) a reservoir made of Type 316 stainless steel containing a centrifugal pump and 2) stainless-steel tubing containing a removable copper test section. The copper test section was OFHC hard-drawn tubing, 11.0 0.05 cm in length and 0.775 ±0.005 cm ID. A Type 316 stainless-steel venturi meter* was inserted in place of the copper test sec- tion in order to determine the lead velocity as a function of pump speed at each temperature. The Cu-Pb system was chosen for this study because the solubility of copper in liquid lead is large enough to measure accurately but small enough that the diameter of the copper tubing was not changed significantly by corrosion. There are no intermediate phases formed in the system, and the solid solubility of lead in copper is vanishingly small so that back-diffusion cannot occur. Molten lead (corroding grade; 99.94+ pct Pb, 0.0015 max pct Cu) was charged from an auxiliary melting furnace into the system under an argon cover to minimize oxidation. The lead was then maintained at constant temperature by a stirred molten salt bath in which the loop was immersed to a depth just above the lead level in the reservoir, Fig. 1. The total volume of lead in the system was 320 2 cu cm.

Jan 1, 1969

By B. Lustman

IT has been known for a number of years that the addition of certain alkaline-earth and rare-earth metals to nickel-chromium base electric resistance alloys causes marked increase in their oxidation resistance as measured in an intermittent oxidation test similar to the ASTM—B 76-39 test. However, the mechanism whereby such additions confer protection is still unknown. On the basis of the experimental observation that the increase in life in intermittent tests of nickel-base alloys is proportional to the atomic radius of the added element, Hessen-bruchl has proposed that the added metal ions occupy holes in the oxide lattice which prevent diffusion of nickel ions in the oxide. Horn2 has postulated that the effect of such additions is to accelerate the rate of diffusion of chromium atoms in the metal and thus to favor the formation of Cr2O3 scales. Hickman and Gulbransen3 concluded from electron diffraction observation that the addition of the elements in question results in the formation of a barrier to the diffusion of nickel ions to the surface. In connection with some experiments conducted to develop a test for the resistance to oxidation of alloys in massive form under conditions of intermittent heating and cooling, some features of the oxidation of nickel-chromium base alloys were revealed which may serve to elucidate the mechanism of protection conferred by rare-earth and alkaline-earth elements. Specimens of cylindrical shape 0.360 in. diam x 0.37 in. long were placed in alumina thimbles and inserted into and withdrawn from a Globar-heated furnace operating at 2150°F at 7.5-min intervals. The weight of oxygen absorbed as well as the weight of oxide spalled were measured at intervals. With the particular experimental conditions used, the specimens in a 7.5-min cycle were at temperature for 2 min which corresponds to the heating time of the ASTM test. The weight changes of similar specimens under conditions of continuous heating in air at 2150°F were also measured. The specimens after oxidation were examined metal- lographically and samples of the spalled oxide collected for X-ray diffraction identification of the phases. The specimens used were from the same lot of material used by Hickman and Gulbransen3 and had the compositions shown in table 1. Included in table I are results of ASTM life tests on the materials in the form of wires. These materials, their composition and the ASTM life test data thereon were all supplied by F. E. Bash of the Driver-Harris Co. It may be noted that alloy 13246 of 80 pct nickel, 20 pct chromium nominal composition showed the shortest life in the ASTM test; alloy 12246 with the addition of small amounts of the elements zirconium, calcium, and aluminum, intermediate life; and alloy 12046 with the further addition of silicon, the longest life. In fig. 1 are shown the results of intermittent oxidation tests made on bulk specimens at 2150°F as well as continuous tests conducted at the same temperature. Duplicate tests were made on each specimen. The ordinate scale, inches of metal oxidized, was derived from the experimentally observed weight gain of oxygen by assuming the scale to be entirely Cr2O3. It may be noted that the metal-loss curves during intermittent oxidation show a constant or continuously increasing rate of weight

Jan 1, 1951

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,&apos; the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*&apos; specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By J. H. Jackson, P. D. Frost, C. H. Lorig, A. C. Loonam

THIS paper describes (1) the effect of sodium on the tensile ductility of magnesium-lithium base alloys, and (2) the precautions necessary to avoid sodium contamination. Effect of Sodium on Properties The harmful effect of sodium in magnesium-lithium base alloys has been recognized by other investigators.1,2 However, quantitative data on its effect have not hitherto been published. The effect of sodium on the ductility of an 87 pct Mg-9 pct Li-4 pct Zn alloy is shown in fig. 1. The sodium was introduced by adding sodium chloride to the flux, which consisted of 50 pct LiC1-50 pct KC1. Moderately high ductility was obtained at an indicated sodium content of about 0.05 pct. Actually, the value probably was less than 0.05 pct, be-cause analyses of the lithium, which were more accurate than those of the alloy, indicated that the highest ductility was obtained when its sodium content was 0.02 pct or less. In fact, in alloys having somewhat greater strength than this particular composition, the sodium content of the lithium must be under 0.01 pct to avoid embrittlement. The effect of sodium on the ductility of several alloys having fairly low strength levels is shown in fig. 2. These alloys were melted with a flux containing 75 pct LiC1-25 pct LiF, to which various quantities of sodium chloride had been added. Sodium had no significant effect in pure magnesium but markedly decreased the ductility of the magnesium-lithium-zinc alloy, even though the alloy contained only 3 pct Li. As the lithium content of the binary alloys was increased, the ductility of the sodium-free alloys also increased. However, the effect of sodium on ductility became progressively more pronounced. Sodium raised the minimum hot-rolling temperatures, particularly those of the high-strength alloys, but its effect, in this respect, was less critical than its effect on tensile ductility. For optimum cold roll-ability, a low-sodium content was required. No deleterious effect of sodium on the stability of properties at slightly elevated temperatures was found. Control of Sodium in the Alloys Optimum ductility is obtained in the magnesium-lithium base alloys when sodium-free materials are used. Commercial lithium was formerly the chief source of contamination. Now purified lithium is usually available. When lithium of ordinary purity is used, the effects of sodium can be minimized by using a flux consisting of 75 pct LiC1-25 pct LiF. Bubbling nitrogen through the melt also helps remove sodium. The damaging influence of sodium on the ductility of the magnesium-lithium base alloys was observed very early in the alloy development program. The discovery came about as a result of chemical analyses made on the lithium used in the alloys. Ductile alloys had been made from lithium containing about 0.2 pct Na, whereas the lithium used in the brittle alloys contained about 0.9 pct Na. The first magnesium-lithium alloys were melted under commercial fluxes ordinarily used in melting magnesium alloys. These fluxes were unsuited for scavenging the contaminating sodium, and the resulting alloys were not ductile. Next, a flux containing 50 pct KC1-50 pct LiCl was tried. This was somewhat more effective but still was not satisfactory. After a number of different experimental fluxes had been investigated, one containing 75 pct LiC1-25 pct LiF was adopted. This flux made it possible to obtain good ductility in the alloys. The

Jan 1, 1951

By W. O. Philbrook, A. E. El-Mehairy

The reduction by hydrogen of individual particles of dense hematite implanted in beds of inert spheres is controlled by single-particle kinetics. No evidence of reagent starvation was found down to low flow rates established by pressure gradients as low as 0.01 in. H2O per- in. of depth in beds of spheres as small as 3/16 in. diam. The optimum size for most rapid reduction of beds of homogeneous ores results from the effect on reducing potential of the gas of competing factors of supply and consumption. A recent publication1 presented the results of a study of the rate of reduction of iron ore in a fixed bed by hydrogen introduced at constant pressure differential. Under these conditions the reagent flow rate varied directly with the bed permeability, which was a function of particle size and shape and bed voidage, and inversely with the temperature-dependent viscosity of the gas. The present note adds data from supplementary experiments designed to reveal whether or not any partial reagent starvation arising from a flow-dependent transport resistance in the gas phase might have been operative. Kinetic studies were made of the reduction of individual spheres of iron oxide inserted into beds of inert spheres, so that the reagent flow rate and aerodynamic conditions were again determined by bed characteristics and temperature. The experimental techniques and apparatus were similar to those previously described.&apos; The synthetic iron ore spheres were wet-rolled by hand from powdered, reagent-grade* Fe2O3 and subsequently dried and then fired in air at 1250°C. The indurated pellets has almost no porosity as indicated by their specific gravity of 5.10. The beds were made of dense alumina spheres, closely sized to the same dimension as the iron oxide spheres, in the following diameters: 3/16, 1/4, 5/16, and 3/8 in. Each bed was hand-packed of particles of a single size to a controlled voidage of 0.32 and depth of 3 in. within a capsule having an internal diameter at least 10 times the particle diameter. A few weighed iron oxide spheres were individually planted in the central plane of the bed of inert spheres at points away from the wall. Reduction was carried out at atmospheric pressure by purified hydrogen at 670°, 800°, and 985°c. The reagent was supplied at precisely controlled pressure differentials of 0.01, 0.02, and 0.03 in. of water per in. of bed depth. This gave a range of flow rates similar to that used in the study of beds of ore and comparable with blast-furnace practice in terms of mols of reducing gas per hr per sq ft of cross-section. Viscous flow prevailed in all beds under the experimental conditions of this study. The reduced particles were checked for loss in weight and then sectioned for metallographic examination. Occasional particles were found to have contained minute internal cracks that interfered with the concentricity of the reduction interfaces, and data for such particles were rejected. An experimental rate constant for the reduction of the imbedded Fe2O3 spheres was calculated on the assumption that the rate was proportional to the metal-oxide interface area by an equation that has been found by McKewan2 to describe the reduction of single spheres

Jan 1, 1962

By T. F. Baily

DURING the period of the War, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the FIG. 1.-EXPERIMENTAL FURNACE. 5000 KW. CAPACITY: 150 TONS 2 PER CENT. SILICON PIG IRON PER DAY. electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted at Canton, Ohio, in

Jan 1, 1930

By J. W. Pugh

PREFERRED orientations in cold-rolled body-centered-cubic metals appear to have remarkable similarity. The as-cold-rolled textures in iron,1,2 silicon-iron,3 mild steel,4 molybdenum, vanadium,&apos; chromium,&apos; tantalum,&apos; tungsten,&apos; and a-zirconium-niobium alloys10 have been determined. These textures have, in some cases, been represented by congrUOUS pole figures and have all been described in one or both of two ways. They have frequently been reported as predominantly (100) <011> orientation

Jan 1, 1959

[TWEEDY, A. M., and VOGEL, FELIX A.: The Briquetting of Flue Dust in the United States by the Schumacher Process, XLVII, [viii], 338. TWEEDY, GEORGE A., and BEALS, ROGER L.: Cyanide-Plant and Practice at the Minas del Tajo, Rosan&apos;o, Sinaha, Mez., XLI, [xl], 324. Twin Falls plant, Peninsular Power Co., LI, 298. Twins, deformation lies in manganese steel, LI, 882. 2,000-Ton Leaching Plant at Anaconda (LAIST and ALDRICH) (With Discussion), LV, [xxiii], 866.]

Jan 1, 1918