Search Documents

By G. Mempel, D. C. Yang, D. W. Fuerstenau

This paper describes details of the design and operation of a batch tumbling mill which has been used for a number of years in the laboratories at the University of California. In order that the energy expended for grinding can be measured accurately, this specially constructed laboratory mill has sensitive torque measuring apparatus. Torque measurements are given for a variety of conditions with this particular mill. In recent years, there have been numerous and fairly extensive investigations of grinding in tumbling mills reported in the literature. Most of these investigations have been carried out in mills with widely differing dimensions. As a result, comparison of results obtained from various investigations has been virtually impossible. If similar mills were used by different investigators, a considerable step forward would be taken in grinding research. A specially constructed laboratory mill with sensitive torque measuring apparatus has been used for a number of years in the laboratories of the University of California. The purpose of this paper is to describe details of the design and operation of this batch tumbling mill so that other researchers, who might be interested in obtaining data for intercomparison, could construct a similar device for their own research. Furthermore, since torque instrumentation is quite expensive, torque measurements are given for a variety of conditions with this particular mill so that those who may not wish to duplicate torque measuring apparatus can make reasonably accurate torque estimates merely by duplicating the loading conditions. It is not intended in this paper to present theoretical derivations of energy consumption in ball mills. This has been done e1sewhere.l-3 CONSTRUCTION OF THE MILL In order to eliminate rust problems with wet grinding, the mill and grinding media are made of stainless steel. The mill shell was rolled from 1/2-in. steel plate. The inside dimensions are 10-in. diam and 11-1/2-in. length, similar to the mill used by Charles.4 It is equipped with eight lifter bars (1/4-in. in height) whose dimensions are given in Fig. 1. The lifter bars have been bolted into the shell so they can be removed for experiments without lifter bars; however, all data presented here are for the mill with lifters. One end of the mill is fitted with two 1/2-in. diam removable plugs for filling the mill with liquid for wet grinding experiments. The mill is mounted on ball bearing rollers as can be seen in Fig. 2. The pillow block bearings are single-row self-aligning sealed ball bearings with 1-1/4 in. hole diam. The bearings supporting the mill shell are single row sealed ball bearings with

Jan 1, 1968

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By Virgil Miller, F. B. Petermann, S. F. Ravitz

The Cle Elum nickeliferous iron deposit is in Kittitas County, Washington, in a rugged, mountainous region about 23 miles north of the town of Cle Elum. The Biewett Pass deposit, which is similar in character and occurrence, is in Chelan County, about 18 miles east of the Cle Elum deposit. A more or less continuous ore zone may extend between the two deposits, since iron ore is reported to have been discovered at Iron Mountain, which lies directly between them. The ore probably was formed by meta-morphism of laterite resulting from Ieach-ing of serpentine derived from peridotite. It consists largely of magnetite grains distributed through a matrix of limonitic material containing a small amount of hematite and chromite. Many of the chromite grains have shells and inclusions of magnetite. The magnetite grains range in size from 1200-mesh to 1/4-in., the average size being 48 to 65-mesh; the chromite grains range from 20 to 150-mesh. The gangue minerals are olivine and serpentine with a small, amount of chlorite, and appear both as very thin bands in the ore and 's minute fragments in the limonitic matrix. The nickel is present as minUte inclusions of a nickel silicate mineral within the magnetite and gangue par- ticles, varying in size from 1500 to about 280-mesh. Detailed analyses of 3000-lb. lots of Cle Elum and Blewett Pass ore are given in Table I. TABLE i.—Analyses of Ore Samples Per Cent Ore from Constituent cle Elum' Blewett Pass Cr....................... 2.23 2-12 Ni...................... 1.43 0.9s Fe...................... 52.9 41.4 SiOz.................... 5.6 13.4 CaO.................... 0.3 0.8 MgO................... 4-1 7-5 AI2O3................... 7.0 2.g P...................... 0.022 0.034 S....................... O.O1 o.oa Mn..................... I.I 0.4 Ba..................... nil co..................... o.oa 0.02 CU..................... 0.02 0.03 As...................... 0.03 Au..................... nil Ag°..................... O.58 Pt...................... ml Fe++.................... 8.9 5-9 Fe+++.................. 44-0 35-5 « Ounces per ton, 1 sr,cte,so,","&&$ally absent: B, W, M~, T~, V, ~i, Bi, Pb. Sb. Sn. Be, In, Hg. Zn, Zr. Cd. Preliminary Tests Attempts to beneficiate the ore by ore-dressing methods, including various 'cornbinations of sink and float, tabling, jigging, flotation, and magnetic separation, were consistently unsuccessful. A wide variety of roasting and leaching tests were made on both raw and reduced ore, but in most of the tests little or no nickel was extracted, and in none did the extraction exceed 50 Per cent. No nickel could be volatilized as the carbonyl. by treating reduced ore with carbon monoxide. Fairly good sepa-

Jan 1, 1944

By L. J. Klinkenberg

It is pointed out that the current concept of pore size distribution is not unequivocally defined and that different methods aiming at a determination of such a distribution therefore do not lead to the same results. A pore size distribution should not be based on the idea that a core should, under all circumstances, behave as a bundle of straight non-interconnected capillaries of the same pore size distribution. This is illustrated by calculations and experiments on the displacement of miscible liquids. INTRODUCTION The introduction of the concept of pore size distribution has been an attempt to characterize the intricate geometry of the flow channels in porous media. As pores in a porous medium are interconnected it is impossible to describe exactly what is meant by a "pore" and, therefore, the term pore size distribution requires further amplification. In the visual method for the determination of pore size distribution "the pore" is considered to be the hole between the grains as observed on thin sections or on a polished surface of the rock under a microscope. In all other presently known methods,1,2 a displacement process is studied and it is ascertained what as- semblaae of straight cylindrical capillaries would show the same behavior. The distribution of the capillary diameters of this assemblage is said to represent the size distribution of the pores of the actual porous medium. From the foregoing it is already apparent that it is useless to try to decide which process or which method of investigation leads to a "correct" pore size distribution. To illustrate this further a displacement process in which a fluid is displaced by another miscible with it will be discussed and the results will be interpreted in terms of a pore size distribution. DISPLACEMENT EXPERIMENTS WITH MISCIBLE LIQUIDS OF NEARLY IDENTICAL VISCOSITY AND DENSITY Interpretation in the Form of a Pore Size Distribution If distilled water is displaced from a homogeneous unconsolidated sand pack by, for instance, a dilute solution of NaCI, the breakthrough recovery i.e., the amount of distilled water produced at the moment the first trace of NaCl can be detected in the effluent water, is between 95 and 100 per cent of the pore volume of the pack. This result can be understood by following in imagination the course of one particle of the liquid. Imagine a length, ?l, at the end of which a liquid particle has an independent chance of a renewed choice of pores of different diameters. In other words, the particle has a choice of traveling time, at, for any length ?l; instead

Jan 1, 1958

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By S. W. Miller

During the examination of welds made in steel by the oxy-acetylene and electric-arc processes, the writer has met with some unusual structures, which he has not encountered elsewhere. They seem to be quite closely associated with the welding methods used, and characteristic of them, and would seem to be worth noting, especially as the references to them in the literature are few, and their explanation not clear or complete. An introductory word or two about fusion welding may not be out of place. The oxy-acetylene process is based on the great and very local heat generated by the burning of acetylene in the presence of commercially pure oxygen, the two gases being thoroughly mixed before combustion. The theoretical temperature is somewhat under 4000" C, but on account of various losses, the actual maximum temperature is probably about 3000" C.' The electric-arc process, using a metal electrode, which is also the filling rod, generates a still higher and more local temperature. The actual temperature of the positive crater of the carbon arc is given as 3500" C.2 NO figures have been found for the temperature of the arc using a metal electrode, but it would probably not be very different from that of the carbon arc, and probably higher than that of the bxy-acetylene flame. The greater localization of the electric arc is due to the fact that it is not surrounded by a large envelope flame, as well as to its higher temperature; while the oxy-acetylene white cone, or welding flame, in which the carbon of the acetylene is burned to CO, is surrounded and preceded by a long envelope flame, itself of quite high temperature, in which the CO is burned to GO2, and the hydrogen of the acetylene to H2O. This flame spreads around and over the pieces being welded, heating them to a further distance from the weld than does the electric arc.

Jan 1, 1918

By Robert Maes, Robert de Strycker

The solidifzcation reactions in the Cu-Sn-As system were determined by microscopic examination, thermal analysis, and X-ray diffraction. The system presents no ternary compound. There is a quasi-binary section, of a simple eutectic type, between the compounds Cu5As2 and SnAs; the system presents, in addition, one ternary eutectic reaction, one ternary peritectic reaction, and seven transitional reactions. The temp-peratures corresponding to each of these reactions were determined, most of them with an accuracy of *lLC. The isothermal lines of the liquidus surface were also established for almost the entire diagram. NO reference was found in the literature relative to the Cu-Sn-As phase diagram and this is believed to be the first study on this subject. The Cu-Sn diagram was taken from Hansen and Anderko;' it is represented by Fig. 1, with the phase designation which will be used in the remainder of this work. For the Cu-As diagram, the solution proposed by Hansen and ~nderko' must be modified to take account of recent data, principally from Heyding and Despault~ and from Hume-Rothery and Burns; this yields the diagram represented by Fig. 2. As for the Sn-As diagram, it is not established with certainty, particularly so far as concerns the solid solubility of tin in arsenic and the solidification reactions near the compound SnsAsz. For this last point, Hansen and Anderko propose two solutions: congruent melting of Sn3Asz with a eutectic SnsAsZ + SnAs or incongruent melting implying a peri-tectic reaction L + SnAs = Sn3As2. Microscopic examination of the few binary alloys prepared in this composition range made us prefer the second of these solutions, which gives the diagram shown by Fig. 3. EXPERIMENTAL METHODS The experimental techniques used in this work were microscopic observation and thermal analysis; a few X-ray diffraction patterns were taken to verify the

Jan 1, 1967

By Charles Burgess

THE improvement, in the quality of cast iron by means of alloy additions has been a metallurgical accomplishment of recent years. Work in this field has shown that chromium is one of the most effective of such additions but, in general, the influence of chromium has been studied only in. connection with other alloying additions, with irons other than foundry irons, or with relatively high percentages of chromium. The present study was initiated for the purpose of determining the influence of small additions of chromium (0.25 to 1.00 per cent) on the quality and resultant properties of cast irons of various foundry grades. The effect of small chromium additions on cast iron was investigated with particular reference to casting characteristics, hardness vs. section, strength, machinability, heat resistance and structure. MATERIAL TESTED Three separate types of cast iron were investigated as to the effect of small chromium additions. The first series of these irons was prepared from remelted foundry cast iron at the Union Carbide and Carbon Research Laboratories, and the other two -series consisted of cupola melts made under usual operating conditions. The first series was made by melting 30-lb. charges of foundry scrap iron containing - 2.86 per cent carbon, 2.72 silicon, 0.50 manganese, 0.062 sulfur and 0.794 phosphorus in a carbon resistance furnace. The chromium was added as high-carbon ferrochrome just before pouring. The irons were cast at approximately 1250° C. (2282° F.). The analysis and physical properties of these irons are given in Table 1, test 1. The second set of cast irons was made in a cupola in accordance with normal practice, 'the charge containing approximately 42 per cent steel scrap and the chromium additions being made to the ladle. Analysis and tests of these heats are shown In Table 1, test 2. A small amount of copper was present in heat C of this series.

Jan 1, 1932

By Ralph Smith

DEVELOPMENT of the lime industry in Ste, Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCO3; 0,35 Si02; 0,3 R203; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ °. Thus the outcrops of the various sedimentaries run approxi-mately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By George F. Comstock

IT has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- [ ] loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferro-alloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. METHOD OF USING DEOXIDIZERS The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel [ ] shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to ¾ -in. lumps,

Jan 1, 1942

By M. W. Fabjanczyk, E. G. Alexander

INTRODUCTION The purpose of this paper is to summarise development of design processes used in the 1100 oreoody as a result of experience encountered. Design methods have been developed as a result of the history of ground behaviour, free-standing qualities of cemented back fill and mass blasting techniques. This paper contains an historical review of design methods previously described by Matthews ( 1972 ) , Hornsby and Sullivan (1977 and 19781, Kirkby, Blair and Hutton (19781, and Stewart (1980). The reasoning behind design philosphy changes are discussed and placed into context with methods now adopted. The 1100 orebody is Mount Isa's main producer of copper ore (5 million tonnes per year ) . Proven reserves are 120 million tonnes at 3.2% Cu. Location of the 1100 orebody in relation to overall mine geometry was well described by Dayton (1976). Geology The orebody is located in a series of massive brecciated shale lenses, in either a siliceous or dolomitic matrix, surrounded and separated by a uniform shale sequence. The whole formation is truncated at depth by a faulted contact with a greenschist facies metamorphic sequence below (Figure 1 and Figure 2) Mathias and Clark (1976). The breccia is known locally as silica dolomite and contains nearly all the economic mineralisation. Interfingering of shale and breccia often results in irregular boundaries to the silica dolomite and the ore limits. Geometry The geometry of the orebodies is shown by Figures 1, 2 and 3. Figure 3 also shows the location of the copper orebodies in relation to the lead orebodies. Structure Although the orebody is contained within the massive breccia (u.c.s. 150-250 MPa), it is cut by shear zones sub-parallel to the regional bedding (north-south striking, dipping approximately 60o to the west), and diagonally by major transverse faults (Figure A). These major faults have continuity in excess of 300 metres, with varying amounts of displacement up to 200 metres, and are zones of potential movement.

Jan 1, 1981

By S. Andrew Kulin, L. Kaufman

A general treatment of the broadening of X-ray double-crystal spectrometer rocking curves due to distributions of tilts and strains has been carried out. The results of this treatment have been applied to the case where dislocations in a crystal give rise to both tilts and strains. On this basis it is found that the rocking-curve halfwidth due to imperfections in the crystal, ßC , increases with increasing Bragg angle, 8. These considerations predict linear relationships between & and tan2 , and ßCand tan 8, for Gaussian and Cauchy distributions of dislocations, respectively. The zero intercept of the ßC us 8 curve, which is a measure of the degree of imperfection of the crystal, is found to depend directly on the distribution rather than the number of dislocations. In addition, the slope-intercept ratio for the ßc - ? curve has been calculated for both the Gaussian and Cauchy distributions. Experimental determination of the - 8 curves for a series of copper single crystals prepared by the Bridgeman and Czochralski methods yields results in agreement with the calculated slope-intercept ratio for a Cauchy distribution of dislocations. CERTAIN X-ray techniques have been used to study the perfection of single crystals. Gay, Hirsch, and Kelly have considered the spreading of spots into arcs on Debye-Sherrer rings due to imperfections. The Double-Crystal Spectrometer has also been applied to this problem.2 The characteristics of Double-Crystal Spectrometer Rocking Curves have been described in the literature by various workers.2-4 By assuming a random spacing of dislocations which give rise to a Gaussian distribution of misorientations relative to some mean orientation in a crystal Gay, et al.,1 arrive at the conclu- sion that the most probable misorientation is given by where h is the spacing between dislocations, and 8 and are the relative misorientations of neighboring regions. If ßC is the halfwidth of the rocking curve (the width at one-half the peak intensity) due to dislocations in the crystal then5

Jan 1, 1960

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By P. G. Shewmon

THIS paper is concerned with the redistribution of a second phase when a 2-phase solid alloy is annealed in a temperature gradient. An examplewhich is discussed in detail is the redistribution of carbides in a low-carbon steel annealed in a temperature gradient below the A, temperature. As a result of such a treatment, the carbides at the cooler side disappear, while those at the hotter side grow in size. In a 2-phase zirconium-hydrogen alloy, the amount of hydride will tend to be increased at the cold end and decreased at the hot end. That such an effect can occur in solid metals is not generally appreciated. However, with the trend toward higher operating temperatures in several fields, this phenomenon will become more important in the future. Actually, such effects should be rather common in the core of nuclear power reactors where the op- erating temperatures are high and temperature gradients are an order of magnitude higher than in previous high-temperature applications of alloys. The purpose of this paper is to point out the existence of such an effect, to discuss the manner in which one predicts whether a redistribution of the second phase will occur in a given system, whether the second phase will go to the hot or cold face, and how rapidly the redistribution will occur. One aspect of this problem has been discussed by pfam and Wernick2who considered the migration of a small liquid region through a solid. In their case, the diffusivity in the liquid is much larger than in the solid and they have interpreted their results successfully by using Fick's first law as the flux equation in the liquid, and taking the concentration gradient from the phase diagram. For all the cases they have studied, this type of analysis predicts that the liquid region migrates from the cold end to the hot end, and this is what was found ex-

Jan 1, 1959

By Franklin Moeller

THE application of electric power for driving, mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere consideration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons 15,680 1b. Weight of skip 8,0001b. Weight of cage 1,8001b. Maximum depth of hoisting 4,000 ft. Diameter of rope 153 in. Total weight suspended on one rope from drum 42,000 1b. Normal hoisting speed 2,700 ft. per minute. Maximum hoisting speed : 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft: depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding ¾ ton, and about 10 cars are the usual load for a skip. All of the ore is clumped into underground bins, which are of different capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 2, 1916

By B. Tani, K. Anderson, I. Johnson, R. Schablaske

INVESTIGATION of the various rare earth-cadmium binary systems discloses the existence of a compound corresponding to the composition MCd6 in all systems save the La-Cd system. Lattice constants for all of the MCde compounds, except LaCd6 which apparently does not form, and PmCd6 whose synthesis was not attempted, are also recorded herein. Iandelli and Ferro 1 report the existence of the compound CeCd6. No additional information, structural details, and so forth are given. Elliott and Lemons2,3' have measured the vapor pressure of cadmium over CeCd6 and have calculated the activity of cadmium in solid CeCd6. These authors find that CeCd6 exists over a composition range from 5.967 to 6.098 (Cd:Ce ratio) at 584oC, and from 5.971 to 6.118 at 639°C. The following is an excerpt from the paper by Elliott and Lemons: 2 "Recently Mr. F. H. Ellinger of this laboratory has indexed an X-ray diffraction powder pattern of CeCd6.00 which we had prepared by gas phase reaction. The compound has a primitive cubic unit cell with a = 15.783 + 0.001A Based on the volume of the cubes surrounding an elemental cerium or an elemental cadmium atom, Mr. Ellinger finds room for 24.10 CeCd6 formula units in the CeCd6 unit cell; similar calculations based on CeCd2 and CeCd11 yield 24.18 formula units per unit cell. The presence of 24 CeCd6 units per unit cell seems probable with an X-ray density of 8.255 grams per cubic centimeter. The most one can say about in-terstitial~ is that there appears to be room in the crystal even at room temperature." Measurements of the solubility of the rare earths in liquid cadmium4 led to the discovery of GdCd6,

Jan 1, 1964

By J. B. Dyess, H. A. Miley

Tarnish films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper.2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen sulphide in air to forml the various oxide-sulphide films studied. The comparative resistances afforded by (I) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of M X 108____ 2DX 96,494 X 103 where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angstrom units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values hf t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939

By J. B. Dyess, H. A. Miley

Tarnish films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper.2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen sulphide in air to forml the various oxide-sulphide films studied. The comparative resistances afforded by (I) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of M X 108____ 2DX 96,494 X 103 where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angstrom units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values hf t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939