Search Documents

By R. F. Domagala

SOME of the results of a program designed to study the kinetics of transformation and related mechanical properties of prototype Zr-X binary alloys systematically are presented here. The object of this program was to provide a sound basis for a scientific approach to the realization of optimum properties in binary zirconium alloys. Alloys of Zr-Mo (eutectoid), Zr-Sn (peritectoid), and Zr-Ti (a and ß isomorphous) were prepared and studied. The data herein are confined to a presentation of the results of studying the eutectoid prototype alloys. The Zr-Mo phase diagram has been determined.&apos; A definitive metallographic study of isothermaily annealed samples prepared from high purity elements served to position a sluggish eutectoid reaction, ß?a + ZrMo2, at 780°C. The compositions of the phases involved in this reaction are: ß, 7.5 ±1 pct Mo; a, <0.18 pct Mo; and ZrMo2, 67.8 pct Mo. Inasmuch as a lower purity sponge zirconium was used in this work boundary placements were rein-vestigated with the less pure alloys. Materials and Procedures Hafnium-free sponge zirconium was used to prepare all ingots. The arc melted hardness of a small button of this zirconium was found to be Vpn 168. Chemical analyses conducted at Armour Research Foucdation are shown in Table I, High purity molybdenum sheet was used as the alloy addition. A typical analysis is shown in Table I. Several 200-g Zr-50 pct Mo alloys were made by arc melting. Crushed granules of this material were used to ensure inqot homogeneity Ailoy ingots were prepared by double melting techniques. First, three 5-lb ingots of each alloy composition were are melted in 2 nonconsumable electrode arc furnace. After melting. the ingots were ground to remove surface defects. A subse-

Jan 1, 1958

The University of Colorado, Boulder, Colo. The University has published a volume, "Geology and Natura Resources of Colorado," by R D George The price is $2 and the volume may be had from the Campus Bookstore, University of Colorado, Boulder, Colorado.

Jan 1, 1933

By D. Kramer

HASEN1 has published a phase diagram for the zirconium-nickel system. This phase diagram has been redetermined by Hayes, Roberson, and paasche2 in the range 0 to 50 at. pct Ni. Recently, Smith and Guard3 have published a tentative diagram for the

Jan 1, 1960

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

"The Butte, Anaconda & Pacific railway extends from Butte to Anaconda. The electrification comprises 30 miles of main line single track, and includes sidings, yard and smelter tracks. When complete the electrified trackage will total about 90 miles on a single track basis.The traffic conditions are unusually severe as they consist principally of hauling copper ore from the Butte mines to the smelters at Anaconda, as well as hauling all the mine supplies, lumber, etc., in both directions; this traffic amounts to approximately 5,000,000 tons of freight per year. The maximum grade against the load is .3 per cent and the maximum train consists of 50 loaded steel ore cars, weighing 3,400 tons. .The locomotive units, two of which will be used for freight trains, weigh approximately 80 tons each. In addition to the freight business, there will be a certain amount of passenger traffic.The power for operating the Butte, Anaconda & Pacific railway is generated by, the Great Falls Power company, and is transmitted to the sub-stations at 100,000 volts. The synchronous motors are supplied with power at a potential of 2,300 volts, 60 cycles, 3-phase. Voltage regulators are installed in each sub¬station to secure the benefit of synchronous condenser effect of the motors.The passenger and freight locomotives are exactly similar, with the exception of the gearing.The roller pantograph mounted on the top of the cab is operated by air from the engineers position.The adoption of the 2,400-volt apparatus for so important a system, where the conditions of operation are so severe, is interesting of itself, as indicating the trend that future electrifications of importance may follow. A trolley potential of 2,400 volts was only adopted after a thorough investigation of other systems already in operation."

Jan 1, 1913

By W. B. Morrison

Anderson, King, and Spreadborough present detailed evidence to show what ~aldwin~&apos; has already pointed out, that, over a relatively small grain-size range (Ad"1/2 ^ 10 mm-&apos;I2, d is average grain diameter), yield point data can fit a number of relationships. Part of the difficulty in obtaining data which reflect only the effect of change in grain size on yielding arises from the fact that in varying the grain size, even though great care is taken, other structural changes are almost certain to occur. In iron alloys, these changes may consist of variations in subgrain size, grain boundary ledge density, and degree of carbon and nitrogen segregation at grain boundaries, all of which are difficult to detect and which may affect yielding, primarily through their effect on dislocation generation. Because of the inherent inaccuracy associated with yield point measurements there is little point in using relatively complex equations to fit data, as was done by Anderson et mnl., rather than the simpler, widely used Hall-Petch equation. In compiling their table of data, it is surprising that they did not include results from certain low-carbon steels,31 in which, as illustrated in Fig. 2, the grain-size range is very much larger than in their Armco Iron. The very fine grains in these steels were obtained by a thermomechanical process. Examination by electron microscopy showed that the grains were separated by high-angle boundarie and contained only an occasional subboundary. The data from these steels obeyed the Hall-Petch equation, and it was shown quite conclusively that they did not fit a d-l or (1-lJ3 relationship. Obviously, a much wider range in grain size than used by Anderson et al. is desirable if we are to determine the true relation between lower yield stress and grain size.

Jan 1, 1969

Iowa Geological Survey, Des Momes, Ia. George F. Kay, State Geologist A list of publications will be sent upon request Most of the papers of the Survey have been published in the Annual Reports, issued since 1892. Separates of the many papers in the Reports may be had for postage, except where they are out of print, and except for vol 1 (1892), 2 (1894) and 14 (1903), where no separates are to be had. Thirty-five Annual Reports have been issued up to and including vol 35 (1929). A charge, plus postage, is made for vols, 4, 5, 7, 8, 9, 10, 28 and 33, others will be sent free upon request, plus postage on from 2 to 6 pounds Space prohibits giving more than a general picture of some of the contents; vols 4, 5, 7, 8, 9, 10, 11, 12, 13, 15, 16, 20, 27, 32, contain, among others, papers on the geology of Iowa, by counties Vol. 19 (1908), 6 lb , contains a number of papers dealing with the peats and coals of Iowa, and has bibliographies of those subjects Vol 22 (1912), 6 lb , contains an annotated bibliography of Iowa geology Vol-24 (1913), 6 lb , contains the analyses of 16 Iowa coals Vol 28 (1917, 1918), price $1 50, 4 lb , completely covers the subject of gypsum in Iowa, and has a bibliography of the sub¬ject. Each volume carries an administrative report and a review of mineral production for the period covered In addition, Technical Paper 2 (1930), Studies of Iowa coals, will be sent free upon request Also a geological map of Iowa, and maps of Iowa showing the distribution of the glacial drift sheets throughout the state, have been issued and are available

Jan 1, 1933

By W. E. C. Coxe

AT the meeting of the Institute in Philadelphia, in June, 1876, it was my pleasure to read a paper on the "Manufacture and Endurance of Iron Rails." I then spoke of some trial rails which had been placed in the down track of the Philadelphia and Reading Railroad, over which passed, in addition to merchandise and passengers, most of the heavy coal traffic of that company. One of these rails, made at the Philadelphia and Reading Rolling Mill in 1870, and then placed in the track, was removed in 1876, after having carried about 55,000,000 gross tons, and was on exhibition at the Centennial Exhibition. A piece of this worn rail, twisted cold, was also shown there. One of the same series of rails was allowed to remain in the track until 1878, and short sections of this rail, as well as one not worn, to show its original shape, are presented for your inspection. A comparison of the two will show that the top of the head or tread has worn down 3/16 ths of an inch during its nine years of service. It carried in that time 67,000,000 gross tons of freight, passengers, cars, and engines. This rail was made in the usual way of manufacturing iron rails at the Philadelphia and Reading Rolling Mill. The head was made from puddled iron bars, piled, heated, and rolled into bars, 4 1/2 and 3 inches wide by 1 inch thick, these bars, breaking joints, were made into a pile in section 9 inches square, heated and rolled into slabs 9 inches wide and 2 inches thick; the balance of the rail-pile was made of 4 1/2 and 3-inch bars, rolled from two-thirds old rails and one-third puddled iron, the

Jan 1, 1880

Statistics compiled by the United States Geological Survey show that the iron ore mined in the United States in 1917 reached a total of 75,288,851 gross tons, exceeding the former record output of 1916 by 121,179 tons. The shipments from the mines in 1917 were 75, 573,181 gross tons, valued at $238,260,333, a decrease in quantity of 2,297,372 tons, or 2.95 per cent., and an increase in value of $56,358,056, or 30.98 per cent., over the shipments in 1916. The average value per ton at the mines for all grades of ore in 1917 was $3.15 as against $2.34 in 1916. Stocks of iron ore at mines, mainly in Minnesota and Michigan, amounted at the close of 1917 to 10,628,908 gross tons, compared with 10,876,352 gross tons in 1916. The quantity of pig iron, exclusive of ferro-alloys, sold or used in 1917, according to reports of producers to the United States Geological Survey, amounted to 38,612,546 gross tons, valued at $1,053,785,975; compared with 39,126,324 gross tons, valued at $663,478,118 in 1916, a decrease of 1.32 per cent. in quantity and an increase of 59 per cent. in value. The average price per ton at furnaces in 1917, as reported to the Survey, was $27.29, compared with $16.96 in 1916, an increase of 61 per cent. The production of pig iron, including ferro-alloys, was 38,647,397 gross tons in 1917, compared with 39,434,797 gross tons in 1916, a decrease of 4.5 per cent., according to figures published by the American Iron and Steel Institute, March 18, 1918.

Jan 12, 1918

By T. S. Lundy, C. J. McHargue

HE diffusion rate of v48 in single crystals of bee vanadium has been determined at temperatures from 1002° to 1888°C. Standard techniques of lathe sectioning were used for specimens annealed above 1500°C while sectioning by grinding was used for specimens annealed at lower temperatures. As will be seen, the lower-temperature data is enhanced on an Arrhenius-type plot relative to values expected by extrapolation of the high-temperature data. Single crystals were obtained from Linde Co. In Table I the analysis supplied by the vendor is compared with an analysis at Oak Ridge National Laboratory of a sample after a diffusion anneal. The isotope v4&apos; was prepared by the Isotopes Division of Oak Ridge National Laboratory. Proton bombardment of a titanium target in the 86-Inch ORNL Cyclotron was followed by a carrier-free chemical separation. Nineteen specimens, 1/2 in. diam and 3/8 in. long, were cut from the as-received vanadium single crystals. Each specimen was machined with the flat face perpendicular to the longitudinal axis. Specimens were polished through 1/0 emery paper and were etched with 25 pct HF-10 pct H2SO4-10 pct HNO3-55 pct H2O. The polishing and etching steps were repeated until a satisfactory surface finish was achieved. The isotope was electroplated onto the specimens from a neutral solution. Counting rates of the deposited layers were approximately 100 counts per sec. At temperatures above 1200°C specimens were annealed in a tantalum resistance furnace under an argon atmosphere. Temperatures were measured with a Pyro micro-optical pyrometer and a Pt-Pt 10 pct Rh thermocouple. At lower temperatures the specimens were sealed in evacuated quartz ampoules and annealed in Kanthal wire-wound horizontal tube furnaces. A severe reaction occurred at 1200°C between the quartz and the vanadium. This

Jan 1, 1965

By C. P. Gazzara and

The modulus of elasticity and yield strength of commercially pure, annealed titanium sheet was investigated at room temperature as a function of strain rate and direction of loading. The value of E varied with direction of measuremeni in the sheet but was unaffected by strain rate in the range 0.04 x 10-to 10-2min-1. The yield strength increased with increase it2 strain rate and varied with specimen orientation. VALUES of the modulus of elasticity, E, in tension for commercially pure titanium have been reported at from 14 to 20Xl06 psi.&apos; Reasons suggested for this variation have been a) composition, b) strain rate, c) texturing, and d) creep. For example, alloys of titanium with aluminum, manganese, and nitrogen have yielded modulus values of from 12.5 to 16.8 x lo6 psi at room temperature.&apos; It was shown by Klier that the modulus in titanium plate was sensi-tive to strain rate. while Dotson and kattus meas- ured variations in E as the strain rate was increased from 3X to 60 min-l. For RC-7OA, 0.040-in. titanium sheet at room temperature Dotson and Kattus found that the average values of E, for specimens in the rolling direction, increased from 14.7 to 16.0 X lo6 psi as the strain rate increased. Simultaneously, the 0.2 pct yield strength increased from 74,700 to 95,700 psi for the same specimens. Differences in yield strength and E have been reported as a function of directionality in titanium sheet.= Dotson and Kattus report such an effect, and Feola6 found in annealed titanium sheet marked anisotropy in tensile strength, yield strength, reduction in area and elongation at room temperature, with

Jan 1, 1961

By E. T. Hayes, A. H. Roberson, M. H. Davies

ZIRCONIUM has been produced on a pilot-plant scale for only a few years, but the potential uses have led a large number of research establishments to engage in a thorough study of the metal and its alloys. The work described in this paper is part of a cooperative project between the Bureau of Mines and the Air Materiel Command. The Zr-Cr system was one of the first investigated because of the possibilities of improving the properties at elevated temperatures, the chemical corrosion resistance, and the mechanical properties of zirconium in a manner similar to the enhancement of the properties of titanium by additions of chromium. There is no published work on the Zr-Cr system but from the similarity of the metals involved it was expected that it would be similar to the Zr-Fe&apos; and Ti-Cr&apos; systems. The materials used in this investigation were prepared in the Bureau of Mines laboratory at Albany, Ore. Zirconium was produced by magnesium reduction of zirconium tetrachloride, and a typical analysis is as follows: Fe, 0.06 pct; Ox, 0.08; N?, 0.01; C, 0.02; and other impurities such as Al, Pb, Ni, Ti, and Si less than 0.01 pct each. High purity chromium was prepared by treating crushed electrolytic chromium in a stream of dried and purified hydrogen." The resulting powder contained about 0.01 pct 0 and about 0.1 pct total metallic impurities. All alloys were prepared by arc-melting 50 g briquetted compacts of the desired composition in a Kroll-type" arc furnace using an inert atmosphere. The furnace was evacuated twice and backfilled with helium, which was gettered by melting a center zirconium button immediately before the alloys were melted. Alloys were remelted at least once to insure greater uniformity of composition and subsequently were annealed in vacuum at 1250°C for 48 hr. Fairly homogeneous alloys were obtained by this means; a slight loss of chromium from the surface by evaporation during the high temperature homogenization was noted. All alloys were analyzed for chromium and gave results in good agreement with the nominal composition. Spot checks on tungsten and nitrogen showed pick-up of these elements to be negligible. Over 70 alloys were prepared for use in this investigation; only the critical ones are shown in Table I. Alloys containing up to 10 pct Cr were amenable to hot working at 850°C and a number of these were sheath rolled to 1/16 in. thickness. Specimens were cut from the sheet for use as metallographic samples. For the thermal analysis a differential couple was used in conjunction with an X-Y recorder, the temperature of the specimen and the difference in ternperature between it and the standard nickel body were recorded simultaneously. Heating and cooling rates of 5°C per min were used. The sensitivity of the instrument was such that a difference in temperature between the specimen and standard equivalent to 0.1 mv produced a deflection of 1 in. on the recording chart. The chromel-alumel thermocouples were checked against a Bureau of Standards calibrated thermocouple. Melting-point determinations were made in a high vacuum induction furnace using an optical pyrometer. The pyrometer, calibrated against nickel, copper, and zirconium (iodide process) under near black body conditions, was focused on the base of a hole drilled in cylindrical samples. A North American Philips Geiger counter X-ray spectrometer was used for all diffraction studies. This instrument, in addition to supplying precise intensity measurements of planar reflections, has an added advantage in that metallographic specimens mounted in bakelite can be used directly, and this

Jan 1, 1953

By S. K. Kawatra

The paper describes a system for on-line analysis of ash in solids in coal slurries for coal cleaning operations. The system consists of two sensors: 1) gama density gauge, and 2) ash sensor. The operational characteristics of each sensor are discussed.

Jan 1, 1980

By R. F. Krueger, L. C. Vogel, P. W. Fischer

Previous studies have shown that the permeabilities of sandstone cores are markedly reduced following exposure to drilling fluid and subsequent clean-up with oil at high-pressure gradients. Laboratory experiments reported in this paper indicate that permeability damage from drilling mud or water can be substantially avoided through use of an initial low-pressure gradient followed by gradually increasing gradients during clean-up by reverse oil flow. On the other hand, attempts to improve the permeability of damaged Berea and oil formation cores with high-rate oil backflush (simulated well stimulation) and low-rate clean-up gave erratic results. Essentfully complete permeability repair was achieved in most of the fresh water-damaged cores from Miocene and Pliocene oil-producing formations; only minor improvement was noted generally in tests with both water-and mud-damaged Berea sandstone. Field well stimulation treatments using high-rate back-flush resulted in long-term productivity improvement when production was brought in at gradually increasing production rates and then restricted to a steady value less than the maximum possible rate. Wellbore plugging at high production rates correlated with increasing solids content in the produced oil. Observations and results from these tests agree with current concepts that formation damage in water-sensitive rocks results from movement and bridging of formation fines, rather than from clay swelling alone. INTRODUCTION Many laboratory studies1-g have shown that the permeabilities of sandstone cores are often markedly reduced following exposure to fresh water or water-base drilling mud filtrate. However, work with cores in the restored state has demonstrated that, although permeabilities to water may be very low for sandstones containing hy-dratable clays, flow of oil can often restore a substantial portion of the effective permeabilities to oi1.Neverthe- less, water invasion into water-sensitive sandstone cores results in varying degrees of permanent reduction in permeability to oil.24&apos; Based on field data, Wade&apos;s statistical study" of well completion effectiveness also indicated a correlation between productivity damage and water invasion during completion. Similar damage can result from fluid invasion during workover. Nowak and Krueger&apos; and Bertness4 observed in their early work (1951-53) that formation damage in water-sensitive sandstones was associated not only with swelling of expandable clays but also with movement of dispersed particles. Subsequent work by Monaghan et al." (1959), Atwood&apos;&apos; (19641, Mungan" (1965) and Gray and Rex&apos;" (1965) has led to general acceptance of the hypothesis that permeability damage in water-sensitive formations is caused by migration of finely dispersed minerals and bridging in "brush heap" arrangements at pore constructions. In laboratory studies, Monaghan et al.&apos; found the use of chemicals to be of only minor value for repairing formation damage. Atwood? however, was successful in substantially repairing damage in a number of low-permeability cores using an n-hexanol flush. In the field, except for treatments with acids, the use of chemical washes to reduce wellbore damage has had limited and sporadic success and generally is unpredictable. A statistical analysis of stimulation treatments in silt-blocked wells has shown that physical manipulation of wash materials is more important than chemical composition." The recent work reported on formation damage in water-sensitive sands brings to mind the results of some unpublished exploratory work done in 1954 in connection with drilling fluid studies.&apos; This laboratory work and subsequent field stimulation treatments indicated a beneficial effect of controlled pressure drawdown and the associated production rate on formation clean-up. This paper reports the results of this work and more recent supplemental experiments on the clean-up of water-sensitive sandstones damaged by water or filtrate invasion. PERMEABILITY RECOVERY AFTER DAMAGE BY DRILLING MUD APPARATUS AND TEST SAMPLES A drilling mud circulating system was used to expose cores to simulated wellbore conditions. The mud flow system is the same as that described by Krueger and Voge17 except that no provision was made for scraping

By T. J. Whalen, M. Humenik

The liquid surface tension of copper-nickel ad copper-nickel-titanium-carbon alloys and the wettability of titanium caybyde by these alloys have been measuhed. It was found that the surface tensions of the binary copper-nickel alloys Lie on a smooth curve between the end members, copper and nickel. The addition of small amounts of titanium and carbon has nO effect on the surface tensions of copper-nickel alloys. Small additions of nickel to copper significantly reduce the contact angle of Ike alloy with titanium carbide. From a Gibbs treatment, nickel is shown to be adsorbed at the titanium carbide-alloy interface. X HE microstructure of two-phase materials has been shown to be influenced largely by the interfacial energies between the phases present.&apos; , In systems prepared by powder metallurgy techniques and densi-fied in the presence of liquid phase, a precise analysis of microstructure and interfacial energy relationships requires a knowledge of the solid-solid interface energies and liquid-solid interface energies. However, marly metal-nonmetal systems are characterized by the "sweating" of the liquid during sintering, and in these systems wettability is a principal consideration. The wetting in turn is dictated by the various interface energies of the system, as shown in Fig. 1 for a liquid drop formed on a solid substrate. The equation which expresses the vectorial balance of surface forces in the horizontal plane, at the point of contact, A, is given by: where ssv = solid-vapor interface energy sSL = solid-liquid interface energy sLV= liquid-vapor interface energy 6 = contact angle measured through the liquid phase. The angle and the surface tension, slv, can be measured accurately by the sessile drop method.3, The absolute value of the surface energy of the solid cannot be determined by this method, but with reasonable changes in the composition of the liquid only, the value of ssv can be considered constant. The changes in contact angle, then, can be attributed to changes in sSL and sLV and since sLV can be measured, the changes in sSL can be determined. Several studies have indicated that the surface and bulk properties of solid alloys can be correlated with electronic structure. The catalytic activity of copper-nickel alloys was reported to follow the dband vacancies in these alloys.5 Nickel has been considered to have 0.6 holes per atom in the d-band. The addition of copper to nickel is thought to bring about a filling of the d-band of nickel, since each copper atom contributes one electron. Thus, at an atomic concentration of 60 Cu-40 Ni (62 wt pct Cu-38 wt pct Ni) the d-band is believed to be full, and magnetic measurements support this view.6 If the electronic structure is influencing a property of the alloy, this property should show some sort of discontinuity as the composition changes from one side of the 60 Cu-40 Ni composition to the other. Since the catalytic activity can be considered as a surface property of the alloy, it is logical to assume that other surface properties, such as surface tension, may also be influenced by electronic structure. The suggestion has been made that there is a correlation between the solid titanium carbide-liquid Cu-Ni alloy interfacial energy and d-band filling.7 One purpose of this investigation was to determine if the changes taking place in the electronic structure with compositional changes in the solid copper-nickel alloys were reflected in the surface tension values of the liquid alloys. Such a change, if present, would lend support to the suggestion that one can refer to discrete energy bands in the liquid state. Other purposes of the present study were to investigate in detail the wettability in the system copper-nickel-titanium carbide, and to discuss the possible processes which take place during wetting in this system.

Jan 1, 1961

By W. C. Hayes

The site selected for the United States prototype pumped storage project of Union Electric CO. was Proffit Mountain, five miles from Taum Sauk, the highest point in Missouri. Factors influencing final location were: high local relief; satisfactory rock type and structure; and an economic location in respect to existing transmission systems. The upper reservoir was constructed by excavating rhyolite porphyry from the crest of Proffit Mountain and constructing a rock fill dike encircling the area to form a 4350-acre foot reservoir. A 6564-ft tunnel connects the upper reservoir with the generating and pumping facilities. A concrete gravity dam on the East Fork of the Black River forms the 6350-acre foot lower reservoir. Precambrian rhyolite porphyry forms the crest of Proffit Mountain and the floor of the upper reservoir. The tunnel was excavated in rhyolite prophpy, granite porphyry, dolomite, shales and conglomerate. Abutments and the foundation of the gravity dam are in rhyolite porphyry, and much of the valley floor of the lower reservoir is underlain by dolomite and shale. Core drilling provided data on soundness of rock type, structure, depth of weathered zone and potential water loss in the fractured igneous rocks. After a six-year study of pumped storage and cost comparison with alternate stream generating units, the Taum Sauk pumped storage project was authorized by Union Electric Co. on Dec. 11, 1959.&apos; The site selected is located in the St. Francois Mountains of southeast Missouri approximately 90 miles south of St. Louis (Fig. 1). The lower reservoir was provided by damming the East Fork of the Black River, a small tributary of the Black River with a minimum flow of about 1 sec ft. Construction of the upper reservoir was effected by quarrying the crest of Proffit Mountain - five miles from Taum Sauk Mountain, the highest point in Missouri — to provide material for a rock fill dike surrounding the quarried area. This provided a 55-acre mountain top lake with a water depth of 92 ft (Fig. 2). A vertical shaft and tunnel connect the upper and lower reservoirs through the two reversible pump-turbine motor-generator units operating under 800 ft of hydraulic head (Fig. 3). The output rating of the plant is 350,000 kw with daytime generation of about 2.2 million kw-hr under normal use. Night pumping will replenish water to the upper reservoir in about 91/2 hours3. The automatic operation is remotely controlled from the Osage plant and from the dispatchers office in St. Louis. GENERAL GEOLOGY Mountains of the St. Francois area consist of Precambrian granites, granite porphyries, extrusive fel-sites and basic dikes. Basal conglomerates overlain by Upper Cambrian Bonneterre dolomites and shales onlap the exhumed Precambrian knobs and hills and are exposed in the narrow valleys. Cambrian and Ordovician residuum as much as 200 ft thick is present on the slopes of many hills. Proffit Mountain consists of rhyolite porphyry and granite porphyry. All excavation for the upper reservoir was in rhyolite porphyry, and the same rock is present under the Bonneterre at the plant site and under alluvium at the lower reservoir dam site. The region has been dissected to the stage of early maturity with only small upland flats remaining. Considerable local relief (a requisite for the project) approaches 1000 ft. Streams flowing across the Precambrian ridges have formed restricted narrows, termed shut-ins. A shut-in approximately two miles downstream from the plant site provides an excellent site for the lower reservoir dam. TEST BORINGS Preliminary to final approval of the project, 12 test borings were made to determine subsurface geologic conditions (Fig. 2). Drill hole No. 12 at the lower reservoir dam site showed 20 ft of alluvium over solid rhyolite porphyry. Drill holes No. 1, 2 and 3 were drilled in the tail race area to depths of 66 ft, 75 ft and 95 ft respectively, and all bottomed in Bonneterre. Drill hole No. 4 at the plant site provided NX core to a total depth of 98 ft in Bonneterre. Drill

Jan 1, 1965

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers&apos; vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By Andrew Mayer

Early in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. E. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense PlantCorporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at I0,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. The Process The process, in brief, is as follows: The raw materials are dolomite and ferro-silicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to then reaction 2(MgOl CaO) + Si = 2Mg + zCaO, Si% It is distilled from the charge and con- densed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of 14 tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. Choosing the Site The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. in the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO and not more than 2 per cent acid-insoluble material. Second, the dolomite should

Jan 1, 1944

By Norman Brown, J. V. Rinnovatore

Substructures in explosively deformed and annealed ß brass have been examined by electron microscopy. In the explosively deformed condition, the structure contains a large density of straight screw type dislocations. Subsequent annealing up to 300oC produces low angle boundaries, which are characterized by superlattice dislocations, and expanded and contracted nodes. Evidence is given where two a(111) superlattice dislocations combine to form two a(001) superlattice dislocations. It is also shown that annealing at 400°C the networks disappear and that quenching from 400" C produces square and circular prismatic dislocation loops that lie on (100) and (111) planes, respectively. THE purpose of this work was to determine the effects of explosive deformation and subsequent annealing in a superlattice using electron microscopy. One of the first observations of explosively deformed structures was made by Hornbogen1 on a iron. Hornbogen found that screw dislocations were most prominent in the explosively deformed structure. He explained this result by suggesting that the edge components of dislocation loops move with the velocity of the shock front leaving a trail of extended screw components. Kressel and Brown2 observed explosively deformed Fe3A1, which is basically a body-centered type of superlattice in terms of dislocation geometry, and found that, as in the case of iron, screw dislocations were most prominent. It was also observed2 that, in cold-rolled and explosively deformed nickel, screw dislocations did not predominate, but rather a uniform network of dislocations was present in which the orientation of the dislocations was random. (Cell structures also have been observed by Nolder and Thomas3 for copper and by Johari and Thomas* for nickel). Kressel and Brown2 discussed the difference between dislocation morphology for bee and fee metals in terms of dislocation mobilities. They suggested that edge dislocations have a greater mobility than screw dislocations in bee metals but not in fee metals. Thus, the idea offered originally by Hornbogen1 is not valid since it should apply equally to fee and bee systems but does not. The results of recent work by Mikkola and cohens on explosively deformed Cu2Au are consistent with other observations for fee metals. They found that dislocations were randomly arranged but there was no significant cell formation. At high shock pressures, deformation twins are produced in fee metals.&apos; High pressures in bee metal should induce the bee — fee transformation while the metal is under pressure. EXPERIMENTAL PROCEDURE The Cu-Zn alloy used in this work contained 51.4 wt pct Cu. Specimens of 0.5 in. diam and 0.012 in.

Jan 1, 1968

By Harold M. Feder, Irving Johnson

Tkermodynamic functions for dilute solutions of uranium in liquid cadmium were obtained from galvanic cell measurements. Deviations from Henvy&apos;s law were observed at concentvations down to 2 x 10-3 atom fraction. Unusually large negative values of the pavtial molal relative enthalpy and excess entvopy of uranium, suggestive of the occu,vvenctwe of partial ovdering of cadmium around uranium in these solutions, were found. The negative relative partial molal enthalpy of uranium at the liquidus accounts for the observed retrogvade solubility of metallic uranium between 473" and about 630°C. The standard free enevgy of formation of UCd,, from a-uranium and liquid cadmium is given by F,° THE constitutional diagram of the U-Cd system,&apos; Fig. 1, is unusual in several respects. The near equality of the Goldschmidt atomic radii2 (Cd, 1.52A U, 1.56A) might be expected to give rise to extensive mutual solubility of the elements except for the restrictions imposed by differences in valence and electronegativity.3 The latter factors must be strongly influential because mutual solubilities in the terminal solid phases are probably negligible, and the solubility of uranium in liquid cadmium in the readily accessible range is only about 1 at. pct. Interestingly, the solubility of uranium in liquid cadmium actually decveases slightly with increasing temperature from 473" to about 630°C. Such a retrograde solubility in a liquid phase is a rare phenomenon in metallic systems; no other authenticated examples were found among the nearly 700 binary phase diagrams compiled by Hansen and Anderko.2 These observations suggested the existence of some unusual interaction between uranium and cadmium. Greater insight into the nature of this interaction was sought by measurement of the thermodynamic properties of the system. EXPERIMENTAL PROCEDURE The emf of cells denoted by the scheme was measured. Each cell consisted of two uranium and two alloy electrodes immersed in a molten lithium chloride-potassium chloride eutectic mixture containing uranium trichloride. The physical arrangement is shown in Fig. 2. The potential between any pair of electrodes could be measured with a Leeds and Northrup Type K-3 potentiometer. The measurements were made at points marked in Fig. 1. It should be noted that points on the phase boundaries represent the concentrations of uranium in the saturated liquid phases of heterogeneous alloys. Uranium Electrodes. Uranium, which is not a particularly soft metal, is capable of retaining residual stresses, and its potential may depend upon its physical condition. Electrodes were prepared from 3-mm diam rods of hot-rolled high-purity4

Jan 1, 1962