Search Documents

By Lawrence Addicks

(San Francisco Meeting, September, 1915) THROUGH the courtesy of Dr. James Douglas I am permitted to give, a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz.. during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper Co. A description of the geology of the district will be-found in the paper by R. E. Somers published in the May, 1915, Bulletin of the Institute. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent 2.35 S, percent 3.0 Ag, ounces per ton 0.05 CaO, per cent 0.5 Au None K202, per cent 4.0 Fe, per cent 1.5 SiO2, per cent 70.0 A120,, per cent 13.0 The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total recovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable.

Jan 8, 1915

By E. V. Daveler

The milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. Character of Ore The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver............ 0.10 oz. Magnesia......... 0.4 per cent. Silica............. 59.7percent. Sulfur............ 1.2 per cent. Iron.............. 5.2 per cent. Lead............. 0.1 per cent. Alumina.......... 21.4percent. Zinc............. 0.2percent.. Lime............. 5.0 per cent. Experimental Work Investigations at the old Perseverance stamp mill had developed the following points: Roughing concentration following stamping gives a fair recovery.

Jan 1, 1920

By Albert Sauveur

IN an important paper on The Critical Ranges of Pure Iron1 presented at the May, 1913, meeting of the Iron and Steel Institute, Professor Carpenter reports and illustrates the results obtained by him in determining the critical points of some very pure electrolytic iron sheet about 0.01 in. thick. The iron strip was rolled into the form of a cylinder 1; in. long and fn in. wide, weighing 42 g., the thermo-couple being inserted in a small hole in the center. The points Ac3 and Ar3 were readily detected, as well as the point Art, but the point Act was absent from every heating curve. The author concluded from this occurrence that the conception of A2 as an independent allotropic change must be abandoned. At the October, 1913, meeting of the American Institute of Mining Engineers, Dr. G. K. Burgess and J. J. Crowe read a paper on The Critical Ranges A2 and A3 of Pure Iron2 in which they described some extremely important experiments conducted by them at the Bureau of Standards, Washington, D. C. They tested Professor Carpenter's electrolytic iron and detected a sharp and well-defined absorption of heat corresponding to the point Act. Professor Carpenter's failure to detect this point is explained by them on the ground that unless the iron be in a single piece entirely surrounding and in contact with the thermo-couple junction, the thermo-couple will integrate the irregular progress of the heat through the sample and the curves will lose their sharpness. In discussing Messrs. Burgess and Crowe's paper, Professor Carpenter accepted this explanation as probably accounting for the absence of Act in his heating curves.

Jan 2, 1914

By Richard F. Miller

Recent studies of creep have made it apparent that plastic deformation may occur in metals under stresses less than the elastic limit as determined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapselll said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was determined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instruments by A. W. Hanson4 on zinc and by Podaschewsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc. AppaRatus The creep-testing apparatus developed for this work is shown in Figs. 1 and 2. The extensometer A is sensitive enough to detect changes in length of 3.3 X 10~6 in. per in., and yet can be used into the plastic range without injury to the apparatus. The specimen,

Jan 1, 1936

By Oliver Ralston

DURING experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent, zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 lb. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: PER CENT. PER CENT. Oz. PER TON Cu 0.695 A1203 0.83 Ag 1.30 Zn 6.17 S...:: 43.35 Au 0.02 Fe 36.23 CaO 0.46 Si02 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: PER CENT. PER CENT. Chalcopyrite 2.0 Schist 3.2 Marmatite 10.32 Quartz 8.2 Pyrite 73.0 Calcite 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as. to render impossible the preparation of commercial grades of concentrate:

Jan 1, 1929

By L. A. Willey, William L. Fink

TWO of the aluminum-alloy systems previously studied—the aluminum-titanium and the aluminum-chromium—exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indicated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. Previous Investigations There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykesl prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2" C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the composition of the intermetallic compounds occurring in this system. Honigschmid2 obtained the compound ZrAla as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zirconium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent A1 (Zr3AI4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent A1 (Zr3A14). Alloys Materials Used.—Electrolytically refined aluminum was employed for thc preparation of all alloys used in this investigation. The chemical

Jan 1, 1939

By William L. Fink, L. A. Willey

TWO of the aluminum-alloy systems previously studied—the aluminum-titanium and the aluminum-chromium—exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indicated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. Previous Investigations There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykesl prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2" C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the composition of the intermetallic compounds occurring in this system. Honigschmid2 obtained the compound ZrAla as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zirconium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent A1 (Zr3AI4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent A1 (Zr3A14). Alloys Materials Used.—Electrolytically refined aluminum was employed for thc preparation of all alloys used in this investigation. The chemical

Jan 1, 1939

By P. R. Sheorey

I read this interesting paper on pillar strength in some detail because this is also my area of interest. It has long been the desire of mining rock mechanicians to predict pillar strength from laboratory compression tests. Considerable literature is available on compression strength of rocks and coal but many of these experiments were conducted not for pillar design but for rock behavior. I have a few comments on the author's approach to pillar design, especially equation (33). Two important factors, which the author seems to have excluded, can be added to the right side of equation (2): time-dependence of strength and the influence of mine environment on strength (moisture and weathering.) The author has taken considerable pains to analyze a large amount of testing data in [Table 1], yielding the various exponents ci of equation (2) (or the subsequent equations derived from it.) He has, however, not shown by means of a worked out example how these values of [Table 1] could be applied to a practical pillar design situation. It would have been interesting to compare predicted pillar size using equation (33) with an actual case. Alternatively, equation (33) could have been used to explain the failure of a pillar, if such a case history were available. Consider we have a large number of case histories of stable and collapsed pillars in a seam and we conduct a large number of tests in a laboratory press. The exponents [ci] can then be determined for actual pillars as well as for test specimens. Thus, equation (2) will read [ ] Since laboratory testing conditions (e.g., between steel platens) are different from the conditions on pillars, the exponents [ci] in

Jan 1, 1983

By Woolsey McA. Johnson

In metallurgical circles it is known widely, but somewhat vaguely, that the ease of reduction of metallic oxides depends largely on the way they hare been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction temperature of zinc oxides variously prepared and of several kinds.' In said paper it was shown that the temperature at which zinc oxide evolves zinc according to the equa-tion ZnO + C = Zn + CO depends upon the nature of the two reacting bodies. The determina-tions had a range of accuracy of from 2° to 6°C., whereas differences were found to amount to an extreme of 90' C. So the differences are real ones and must have a definite cause. The equation of boiling water, (H2O)4 D 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. In general, all equations reacting in the liquid or the gaseous phase have well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the tempera ture conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules. In other words, there are two forces to be overcome: a certain

Jan 1, 1914

By Samuel Daniels

Aluminum-base alloys containing small amounts of copper and magnesium possess but ordinary physical properties as sand cast, but may be treated to give a remarkable range of tensile values and of Brinell hardness. The high-copper (4.5 per cent.) duralumins must be given a protracted treatment which in nature resembles the malleableizing of white cast iron; the low-copper (2.25 per cent.) duralumins develop an excellent combination of strength and ductility with a treatment which requires a maximum of 5 hr. to be completed. THE wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating to 932° F. (500° C.) for 2 hr., cooling in, air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that " considerable improvement in the mechanical properties of copper-aluminum alloys' may be obtained from suitable heat treatment applied to castings."2 Jeffries and Gibson3 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932° F. in a

Jan 7, 1924

By Perry G. Harrison

The first autlientic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is. said to have worked out his process. Jacobil in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeS04 + (NH4)2SO4. Lenz2 described some properties of electrolytically precipitated iron. He used Klein's bath, FeS0, + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By C. A. Mitke

During September, 1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft mere found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97", and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness and the injector mas tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company. After the above tests had been made on the oxygen apparatus, the men still complained about leaky helmets. Small quantities of gas entered the helmets and could not be detected by these methods. The

Jan 1, 1914

By F. E. Bash

WHENEVER electric and open-hearth steel men discuss the relative advantages of their respective methods, the question of temperature is always discussed, so that this paper is written in the hope that definite data may settle some of the questions and encourage further investigations along these lilies. The writer has had the opportunity of taking the tapping temperatures of steel from electric furnaces of different sizes in various plants and from a number of open hearths handling the same kind of steel. All temperature measurements were made with the same disappearing-filament type optical pyrometer and the corrections for emissivity applied were those worked out by Burgess,1 which are 0.40 for steel streams and 0.65 for slag. The correction is applied by calculating the curve giving the relation between the true and apparent temperature in the following formula: Log E = CZ log e( 1 _ 1 x \T2 T1) in which E = emissivity; C2 = 14,500; e = base of Napierien logarithms; ? = wave-length of light used = 0.65/4; T2 = true temperature, in degrees absolute; T,1 apparent temperature, in degrees absolute. The curve showing the relation between true and apparent temperature for steel and slag arc given in Fig. 1. For the purpose of comparison of open-hearth and electric furnaces, there are given in Table 1 the tapping temperatures of two 25-ton Heroult electric furnaces and one 6-ton with one 50-ton acid, one 40-ton basic, and one 65-ton acid open-hearth furnace, all making nickel ordnance steel for guns. The two 25-ton Heroult electric furnaces were finishing steel refined by the triplex process and the 6-ton Heroult finished steel that was partly refined in an open hearth.. In this table, the tapping temperature and the temperature of the steel stream into the first ingot

Jan 9, 1919

By J. A. Bownocker

THE Pittsburgh is one of the most important coal beds of Ohio. It was the last of the great coal beds to be worked extensively in that State, has the largest area of virgin coal, and will in all probability be the last of the great deposits to be exhausted. The line of outcrop sweeps nearly southwest in a sinuous line from Jefferson County on the north to Lawrence on the south, a distance on a bee-line of at least 150 miles. (Fig. 1.) The maximum width of the area under which this coal is due is about 55 miles, but in most places it is less than half that and in the two southern counties it is in places restricted to narrow ridges. Here as elsewhere the Pittsburgh coal forms the base of the Monongahela formation, and the following section taken from Condit shows the position of this bed with reference to certain higher ones in this field:1 FEET INCHES Shales and thin beds of limestone 24 5 Coal, Meigs Creek, No. 9 4 0 Shale, sandy 11 0 Coal 0 8 Shale, clayey 6 0 Coal, Lower Meigs Creek 3 0 Shales,clayey 2 0 Limestones and thin layers of clay 25 0 Unseen 11 0 Coal, Redstone 2 0 Unseen 11 0 Coal, Pittsburgh, No. 8 8 0 Clay 5 0 Limestone 4 0 From the standpoint of continuity the Pittsburgh coal of Ohio must be classed with the patchy type. As the map shows, the coal is thin or wanting along many miles of the line of outcrop. The large deposits form three separate areas, which, in order of their importance, are generally known as (1) the Belmont, (2) the Federal Creek, and (3) the Gallia fields.

Jan 10, 1926

By J. H. Frye, J. W. Caum, R. M. Treco

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."' It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. Hardness, Lattice Parameter and Ionic Overlap Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2. It is believed that most of the values are accurate within the limits indicated by the rectangles. These data are also presented in Table I. Ultimate Meyer hardness, P u, is defined by the equation: where L = load, D = diametei of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. The question arises as to whether Or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."' It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. Hardness, Lattice Parameter and Ionic Overlap Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2. It is believed that most of the values are accurate within the limits indicated by the rectangles. These data are also presented in Table I. Ultimate Meyer hardness, P u, is defined by the equation: where L = load, D = diametei of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. The question arises as to whether Or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By Gherman Pavlovich Nikonov

Results of preliminary research on the use of small diameter water jets at high pressure for cutting rocks has demonstrated the possibility of effective cutting of anthracite. Detailed research has, therefore, been conducted at the Skotchinsky Institute of Mining to study the dynamics and structure of the small water jets and the mechanism by which they cut coal. One of the objects of this research was to obtain data for the design of a machine for cutting rock, based on the same principles as that for cutting coal. The productivity of water jet mining machines depends on the hydro- dynamic parameters of the jet. Therefore, the research on small diameter water jets was directed, initially to a study of the nature of the variation of these parameters, and to obtain a profile of dynamic pressure distribution over the section of the jet. As has been confirmed previously, the required jet pressure (to cut coal) lies in the range of 100 to 500 atmospheres. These pressures were utilized for the research. The diameter of the nozzle was changed as ~follows; 0.97; 1.24; 1.5; 2.17; 2.87; and 3.57 mm. Graphs showing dynamic pressures for each nozzle diameter and varied axial dynamic pressure were obtained over distances ranging from 2 to 70 cm from the nozzle. One of the most important hydrodynamic parameters of a jet, closely related to the dynamics of jet disturbance in air, is the magnitude of the axial dynhmic pressure. A study of the variation in this pressure with increasing distance from the nozzle led to the separation of the jet into three specific parts, which differ from each other not only in the nature of the change in dynamic pressure, but also in structural properties.

Jan 1, 1971

By H. M. O?Harra

Experiments have shown that the use of enriched air would be of particular benefit in the roasting of zinc ores for the manufacture of sulfuric acid. Enriched air increases capacity of furnace, decreases fuel consumption, and increases SO2 content of roaster gas. THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper distribution of heat in the furnace;1 the volume of enriched air,

Jan 3, 1924

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct ThO2,*, and the ilmenite 56 1/2 pct TiO2, whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be avail- able in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources. 1 Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations.

Jan 6, 1950

By J. Mizrahi, A. Brillantshtein, A. Mitzmager, O. Schächter

The separation of synthetic mixtures of heavy minerals by hindered settling classification and jigging was comparatively tested in water and five organic heavy liquids, of various specific gravities and viscosities. It was found that in the hindered settling classification process the separation efficiency was directly proportional to the concentration criterion, the liquid viscosity being a minor factor. There is therefore a decisive advantage in using heavy liquids as classification medium. In the jigging process the advantage of using a heavy liquid is masked by the detrimental effect of a higher liquid viscosity, which, in this case constitutes an important factor. Considerable interest has been aroused lately by the development of mineral beneficiation techniques 1,2 using TBE (tetrabromoethane), a heavy liquid of specific gravity of 2.96, which has been made available for industrial use by a new process3 producing TBE directly from the Dead Sea brines at a reasonable price. Most of the applications investigated until now were based on the sink-float separation of minerals in a heavy liquid of intermediate specific gravity. The TBE can be conveniently diluted with many organic solvents, and thus sharp separations are possible in a wide range of specific gravities up to 2.96. Although this maximum specific gravity is sufficient on most cases for the elimination of the bulk of the barren gangue and the production of marketable concentrates, some practical problems came up for investigation in which the separation of two (or more) minerals, heavier than TBE, was required.* *Among the cases studied in the IMI Laboratorles which fall into this category we can mention: alluvial deposits, such as heavy minerals in sea sand, tin deposits, or ground coarse-grained rocks, such as pegmatites. In such cases where, due to the petrographic structure, further fine grinding is required in order to achieve the liberation of the heavy components, the

Jan 1, 1964