Search Documents

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at temperatures from 0 to approximately 1030' C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825" C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some additional data which will subsequently be described. Materials and Methods The alloys used in this investigation are listed in Table 1. They were prepared in 30 or 50-gram ingots by melting specially purified silicon and electrolytic or carbonyl iron in alundum crucibles under a pressure of less than 1 mm. of mercury. The purity of the silicon, electrolytic and carbonyl irons has been given by the authors in previous publications2, 5. The ingots were homogenized in vacuo at approximately 1000" C. for at least 96 hr. and then slowly cooled. The homogenized specimens were ground to powder in a hardened steel mortar. This powder was passed through a 150 or 200-mesh screen and sealed in evacuated quartz, Jena or Pyrex glass tubes and heat-treated as noted in the various tables. Specimens 23A, 24B, 33 and 35 and the specimens heated for one month at 700" C. were quenched by quickly removing the tubes from a horizontal tubular furnace and dropping them into water. The other specimens were quenched by means of a drop-quenching device, which has been described previously3.

Jan 1, 1937

By John P. Harmon

This paper was written with two objects in view: (1) To describe in detail what has been done toward the ventilation of the main unit of the Portovelo mines and the results; (2) to give information that may be useful to anyone who may have to make a preliminary mine ventilation survey, with recommendations for the improvement of the existing system and finally the maintenance of the improved system. General Description The mining operations of the South American Development Co. at Portovelo, Province of El oro, Ecuador, are described here only briefly, as a full discussion does not fall within the scope of this paper. The orebodies are of the steeply dipping, gold quartz vein type, averaging about 2.0 meters wide. As shown in Fig. 1, the ore chutes are relatively far apart, making considerable development work necessary before connecting raises can be driven between the levels. Faulting' on a large scale and a parallel vein system have made long dead-end drifts and many crosscuts necessary in the exploration of veins. The ventilation of these dead ends is described under Auxiliary Ventilation. The method of mining2 is the filled rill stope method, similar to the method that is largely employed at the Butte mines. The main shaft of the mine is in the Amarillo Valley, on either side of which mountains rise abruptly to a height of several hundred feet above the collar of the shaft. Entrance is made to the mine: (1) Through the American shaft, which extends vertically from the surface to a depth of 1100 ft., of which only the first 700 ft. are in active use at the present time; (2) levels are driven from the American shaft at intervals of 30 m. (100 ft.), of which only the third, fifth and seventh levels need be considered in the ventilation problem; (3) adits at intervals of 30 m. (100 ft.), with a few exceptions, above the collar of the American shaft.

Jan 1, 1931

By R. Kossowsky, W. C. Johnston

CONSIDERABLE experimental data has been published in recent years on a few directionally solidified aluminum base eutectic alloys. The mechanical properties of A1-Al3Ni eutectic have been studied by Lemkey, Hertzberg, and Ford1',2 and Salkind et a1.3 where the alloy has been demonstrated to behave as a whisker reinforced composite with superior properties over many aluminum alloys. It has also been shown4 that aluminum reinforced with Al3Ni whiskers R. KOSSOWSKY, Member AIME, is Senior Metallurgist, Westing-house Research Laboratories, Pittsburgh, Pa. W. C. JOHNSTON, formerly with Westinghouse Research Laboratories, is Head, Department of Physics, George Mason College, University of Virginia, Fairfax, Va. Manuscript submitted March 28. 1969. IMD__________________ possesses excellent microstructural stability to 508°C. The effect of lamellar structure in A1-CuA12 eutectic was compared3 to the rod-like structure in the A1-Al3Ni eutectic, and was found to be better in low cycle fatigue. This was rationalized3 by postulating that a lamellar reinforcement was more efficient at blocking lateral plastic flow than a rod-like rein-forcement. The purpose of this study is to explore eutectic strengthening in other aluminum base alloys. The Al-Pd system5 forms a eutectic with aluminum and the intermetallic compound A13Pd at 25 wt pct Pd, and has a melting point of 615°C. A13Pd has an orthorhom-bic structure and transforms to hexagonal Pd2A13 at 785°C. Growth characteristics, compression yield strength, creep rupture, and microstructural stability of directionally solidified and as-cast alloys are investigated. Eutectic ingots having a nominal composition of 25 wt pct Pd were prepared by first compacting 1/2 in. diam by a in. high pellets from 99.99+ pct A1 and 99.99 pct Pd powders. The pellets were then levitation cast into 1/4 in. diam by 2 in. long copper molds. Directionally solidified bars were prepared by grinding the cast ingots to 0.195 in. diam, inserting them into alumina

Jan 1, 1970

By W. S. Weeks

In coursing the ventilating air through a mine it is often necessary to restrict a comparatively open split in order that it may carry exactly the desired quantity of air. Such a restriction is known as a regulator, and usually takes the form of a partition with a hole in it. The quantity of air circulating is controlled by the size of the hole or orifice. For example, it is desired to force a quantity q I cu. ft, per min. through split a (Fig. 1) and the quantity q2 through split b. It requires a pressure of 2 in. water to force the desired quantity through a, and a pressure of 1 in. to force the desired amount through b. The pressure drop between points A and B must be 2 in and a pressure of 1 in. must be destroyed in split b. This is done by inserting a regulator in b, which causes the velocity to increase in the orifice and results in a change from pressure-head to velocity-head. If the air, after passing the orifice, is slowed down in a turbulent manner, all of the velocity-head does not change back into pressure-head, so a permanent loss of static pressure results. A classic formula for computing the area of an orifice to destroy a certain amount of static pressure has been handed down from early days: 0.0004Q a =2 This formula is based on the assumption that all velocity-head in the orifice is "destroyed;" that is, does not reappear again as either velocity-pressure or static pressure. The derivation of the formula is as follows: h = head lost in regulator in fect of air. v = velocity in regulator in fect per second. q = quantity circulating in cubic feet per second. Q = quantity circulating in cubic feet pcr minute. a = area of orifice in square feet.

Jan 1, 1928

By E. Robert Ruhlman

The term potash refers to potassium oxide (K2O), a compound not found in nature or produced by man but used as a basis for comparison of all potassium compounds and now is applied generally to various compounds of potassium used by agriculture and industry. Potassium, the last of the three major plant foods to be used in appreciable quantities by agriculture, was originally produced only from organic materials for chemical uses. The first recorded identification of a mineral source of potassium was in 1797; but, until the discovery in 1839 of the large deposits of soluble potassium salts in Germany and their development in 1860-61, nearly all potassium compounds continued to come from organic sources. With the importance of potash to plant life discovered in 1840 by von Liebig and the production of potash in Germany after 1861, agriculture soon became the major consumer of potash. In 1958 agriculture accounted for about 95 pct of the total potash consumption; the chemical industry used the remaining 5 pct. Mineralogy and Geology Potassium, an important constituent of the earth's crust, occurs in many forms in numerous rocks and minerals, including water solutions, but is not found in its native state. Twenty-five of the more important potash minerals are listed in Table 1. The properties of the five potash minerals most common in Permian salt formations follow: Sylvite is isometric; has a hardness of 2, a specific gravity of 1.98, vitreous luster, and cubic cleavage; and ranges in color from clear to brick red. In taste it is similar to halite but has a sharper taste and a cooling effect on the tongue. It is very plastic under pressure. Langbeinite is isometric; has a hardness of 4, a specific gravity of 2.82, vitreous luster, conchoidal fracture, and no cleavage; and ranges in color from clear to gray. It is taste- [ ] less, somewhat granular, and slowly soluble in water. Polyhalite is triclinic; has a hardness of 3, a specific gravity of 2.77, and dull luster; and

Jan 1, 1960

By R. L. Frink

I FEAR that my treatment of this subject may not, in all instances, meet the approval of those who read my opinion as to the utility and efficiency of pyrometers in the making of glass, or bottle-glass. It may be superfluous for me to add that this opening statement is based on over 15 years' experience in an endeavor to successfully apply pyrometers, or heat-measuring instruments, to glass-melting furnaces, particularly the type known as tank-furnaces, and that such endeavors have proved more or less futile. It is my desire, therefore, to herein set forth the problems encountered, hoping thereby to stimulate further effort in the successful application of pyrometers. It is my desire, also, to invite criticism of the methods used and suggestions from those who may have a wider experience, or who may have better methods. Fin. 1.-GLASS TANK FURNACE. In general, I believe that the inefficient application of pyrometry to the melting of glass in tank furnaces is not due as much to the instruments as to the conditions under which they must be used and the character of the medium in which they must reside. Most of those present no doubt, are familiar, at least in a general way, with the methods and apparatus used in the melting and making of bottle-glass, or glass that is formed into containers of various shapes and designs. Most of this glass is made in what is known as a tank furnace, these furnaces vary widely in design and construction. In general, they consist of a rectangular tank-like form, built up of fireclay blocks, and range from 2 by 4 ft. (0.6 by 1.2 m.) to 24 by 140 ft. (7.3 by 42.6 m.) with a depth of glass from 2 to 5 ft.; or a capacity of from approximately. 2 to 700 tons. Fig. 1 shows the general

Jan 9, 1919

By H. Margolin, E. Ence

In order to understand the effect of zirconium on properties of Ti-Cu-A1 alloys, Ti-Zr alloys were examined for the presence of ordering or compounds at the following compositions in weight percent: 24.1 pct Zr (lZr:GTi), 32.2 pct Zr (lZr:4Ti), 38.8 pct Zr (lZr:3Ti), 49.0 pct Zr(1Zr:ZTi). Alloys were prepared as 15-g buttons by non- consumable arc melting under argon atmosphere from Bureau of Mines titanium (Bhn 63) and Reactor Grade zirconium (Bhn 150). Weight losses during melting did not exceed 1 pct of the initial button weight. Prior to heat treatment, buttons were hot-rolled at 600" to 700°C to rods of about 6 mm diam. Contamination after hot-rolling was found to extend to a depth of less than 0.5 mm. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. Annealing times were as follows: 700°C — 7 days; 600°C— 14 days; 575°C-1 and 2 months; 525°C-2 months; 500°C-2 months. Prior to heat treatment, all Ti-Zr alloys were vacuum annealed at 900°C to remove hydrogen. The reanneal of 575°C specimens for an additional month produced no observable microstructure changes. The results obtained by microstructure and X-ray diffraction are shown in Fig. 1, together with data of Hayes et al.' No other phases than a or P were found. Small amounts of retained P were detected by X-ray in the 49 pct Zr alloy. The data of the present investigation suggests that ß and a transus boundaries are at considerably lower temperatures than those of Hayes et al. The work of Hayes et al. is based on sponge titanium and Bureau of Mines zirconium, both of which contained 0.15 pct 0. Since melting was performed in

Jan 1, 1962

By D. Kelly Campbell

Cleveland-Cliffs Conveyor System Uses Twisted Belt To: 1 -Beat Upper Peninsula Weather 2- Solve Underground Transportation Problems

Jan 7, 1953

By R. Schuhmann, E. J. Michal

Experimental measurements are reported for the oxygen pressures of iron-silicate slags in equilibrium with solid silica. CO2-CO mixtures were bubbled through the slags in silica crucibles to find equilibrium values of p co2/p co over the entire composition range of silica-saturated slags at 1250°, 1300°, and 1350°C. From the data, the activity vs. composition relationships were calculated for O, FeO, and Fe. SLAGS composed primarily of silica and iron oxides have particular practical importance in copper smelting,' in acid steelmaking, and in accounting for the service behavior of silica refractories. These slags all contain both ferrous and ferric iron, so that, strictly speaking, they are ternary or three-component liquid solutions. For convenience, the components may be taken as the three oxides, FeO, Fe2O3, and SiO2. The constitution of the FeO-Fe,O,-SiO, system at slagmaking temperatures has been studied in a recent investigation described in a separate paper.' This work showed the compositional ranges of iron-silicate melts at temperatures up to 1450°C and also the temperature-composition relationships for melts in equilibrium with various solid phases, including iron, wüstite, magnetite, and silica. Broadly speaking, the compositions of iron-silicate melts at a given temperature should be thought of as varying over a two-dimensional field. In the first place, the silica/total iron oxide relationship varies from maximum silica for silica-saturated melts to minimum silica for wüstite-saturated melts or, at higher temperatures, to zero silica for straight iron oxide melts. In copper smelting, for example, the converter slags approach the low silica limits while the reverberatory-furnace slags have intermediate silica contents, perhaps approaching silica saturation in some circumstances. Liquids formed in the pores of silica refractories presumably are close to silica saturation. The second type of composition variation is in the ferric/ferrous relationship, which depends on how oxidizing or how reducing the process conditions are. Relatively reducing slags, such as acid-steelmaking slags, are lower in ferric oxide and ap- proach saturation with metallic iron. Oxidized slags, such as copper-smelting slags, contain larger percentages of ferric oxides and approach or reach saturation with magnetite. Since these two kinds of compositional variations are closely related to two general properties of interest for all metallurgical slags, basicity, and oxidizing power, it is hoped that the thermodynamic study of iron-silicate slags eventually will throw further light on the significance and nature of these long-recognized but as yet poorly understood slag properties. Measurements of oxygen activity as a function of slag composition, using CO-CO2 gas mixture to fix oxygen activities, afford an experimentally convenient approach to the study of the thermodynamic properties of iron-silicate slags. In a preceding investigation,³ his approach was used in a systematic study of iron-silicate slags in equilibrium with solid iron. The present paper gives the results of a similar study of the iron-silicate slags in equilibrium with solid silica. The experimental work consisted in the determination of CO2: CO ratios in gas mixtures at equilibrium in the system: gas: liquid slag: silica Determinations were made at temperatures from 1250° to 1350°C for slags ranging in composition from iron saturation to magnetite saturation. Also, equilibrium CO,: CO ratios and slag compositions were determined for the univariant systems: gas: liquid slag: silica: iron gas: liquid slag: silica: magnetite Experimental Methods The experimental procedure was essentially the same as that used in the previous study of iron-silicate slags saturated with solid iron," but in order to work with the silica-saturated slags an all-silica crucible assembly was used. A liquid slag was prepared from pure prefused stock materials and brought to equilibrium with the silica crucible at the desired temperature. Then a mixture of CO2 and CO was continuously bubbled through the melt

Jan 1, 1953

By Robert Lepsoe

It is generally realized that in cyaniding the precipitation efficiency of zinc dust is due to the fine division or extended surface of its metallic particles; but frequently it is thought that the presence of other metals, say 2 to 3 percent. lead, is advantageous, causing more complete precipitation. The results of testing about fifty brands of commercial zinc dust have led to the conclusion that there is a distinct relation of precipitation efficiency to fineness and that the effect generally can be estimated by examining the size of metallic particles. The presence of lead was not found to be of any importance. Specifications Generally the term "97 per cent. to pass a 350-mesh screen, 95 to 97 per cent. uncombined metallic zinc" is used by the leading European exporters. Among the many methods of determination of metallic zinc, I have found the iodine test (iodine in potassium iodide) very satisfactory and rapid. It has been controlled by the other methods, samples of the same product having been sent to three different analysts: Iodine method................... 98.11 per cent. metallic zinc, Volumetric method.............. 07.63 per cent. metallic zinc, Ledoux Co., New York Bichromate method.............. 08.16 per cent. metallic zinc, Watson Gray, Liverpool. England Bichromate method.............. 98.20 per cent. metallic zinc, Norway Inst. of Tech., Trondhjem Determination of Precipitation Efficiency The method devised by W. J. Sharwoodl was used. The method proved to be satisfactory, the tests being merely for the comparison of different samples, hence the personal factor in manipulation was eliminated. As nearly all tests showed more zinc in solution than was accounted for by the silver precipitated, the term "dissolved zinc" was introduced—it means zinc dissolved by the action of cyanide and oxygen: Zn + 4KCN + H2O + O = K2Zn(CN)4 + 2KOH; or more probably, resolution of its equivalent precipitated silver, as tests stirred two hours showed more "dissolved zinc" than those stirred

Jan 1, 1925

By Edward Keller

GOLD MOVEMENT ON SURFACE OF AURIFEROUS COPPER WHEN LATTER IS SUBJECTED TO OXIDATION SOME years ago the writer's attention was called to the fact that rolling-mill scales from auriferous copper do not have the gold content proportional to the gold contained in the copper from which they are derived. I So, later, he made a few simple experiments, which are described herewith. In: order to test the gold movement on the changing surface of a copper plate under the influence of oxidation, plates 6 in. by 8 in. by I in. (15.2 cm. by 20.3 cm. by 2.5 cm.) of converter copper, refined, of 99.29 per cent. purity, and leaded copper with a content of 95.65 per cent. copper, were obtained. Ten cuts were made through the thickness of the plates along the longitudinal center and the silver and gold content ascertained in each of the 10 samples in both plates, as shown in the accompanying illustration. The assay results, recorded in Tables 1 and 2, show that the gold distribution is relatively uniform in both plates, while silver has greater variations, especially in the leaded plate. The plates subjected to oxidation were placed in a red-hot muffle for about 2 hr., two small scorifiers being used as supports. Arranged alongside each other, they nearly filled the width of the muffle, and so were practically under equal conditions of heat and draft. The accurate observance of the time was not possible, however, because of other work, but the time of the exposure of each plate in a pair was identical. At the end of each period, each plate was plunged into water and completely freed of scale, which was carefully collected, dried, weighed, and analyzed. Samples of the plates had also been taken of the molten metal and duly analyzed. Table 3 contains the analytical data for the two plates and their several sheets, or layers, of oxide scales. These figures show that in the oxidations of the converter copper the silver is fairly uniform, while

Jan 1, 1919

By Otto W. Nuttli

THE magnetic method of prospecting is well suited to determination of faulting in the basement rock. In addition to establishing the horizontal position of the fault, it often furnishes valuable information concerning the depth and amount of faulting. Consider a simple case of a vertical fault, represented in cross-section in Fig. 1. Let A A' represent the plane of observation (ordinarily the surface of the earth), and BB'B"B"' the upper surface of the basement. Assume that the sedimentary rocks are nonmagnetic, so that the magnetic susceptibility of the material above the basement is zero. Let k indicate the susceptibility of the basement rock, c the density contrast between it and the neighboring sedimentary rocks, and the amount of vertical displacement. Fig. 1 shows the material, indicated by cross- hatching, which gives rise to the magnetic anomaly. In most cases it can be assumed that is small compared to the thickness of the sedimentary rocks. The semi-infinite, rectangular slab of rock of susceptibility k, density contrast , and thickness t may then be replaced by a semi-infinite sheet CC' of mass t per unit area at depth 2 (the mean depth of the slab). Nettleton 1 states that this approximation results in an error of less than 2 pct for the computed gravitational field intensity when t is as great as 2/2 and decreases rapidly for smaller values of t. By a theorem of Poisson, the magnetic field intensity can be determined readily from the gravitational field. The theorem states that W = (I/) • (U/i) i1 [1] where W is the magnetic potential associated with the structure, I is the intensity of magnetization which is assumed to have the direction of the inducing field, ? is the constant of gravitation, the density contrast, U the gravitational potential associated with the structure, i the direction of the inducing magnetic field, and i1 a unit vector in that direction. The multiplication indicated in Eq. 1 is

Jan 1, 1956

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By D. H. Polonis, J. G. Parr

IN a recent paper on titanium-rich Ti-Fe alloys,' the hardness of quenched powder specimens was given, together with the amounts of martensitic a they contained. The values disagreed in two respects with previous determinations that Worner² made on lump specimens: 1—Some martensitic a' is formed in powder specimens of alloys containing up to 12 atomic pct Fe. On the other hand, Worner reports that, although his results on quenched lumps are not conclusive, alloys containing more than about 4 pct Fe "appear to consist of retained ß'' although they "may not be strictly unaltered solid solutions." 2—According to Worner, quenched lump specimens show a maximum hardness at a composition about 3.5 pct Fe. Earlier -experiments by the authors showed a maximum hardness of martensitic alloys in powder form at 10 pct Fe. Accordingly, more experiments have been conducted in order to confirm these differences and to determine with more accuracy the minimum composition of quenched lump specimens that consist entirely of retained ß. Lump samples?x?x1/20 in. were quenched from 1000°C in helium and, on the whole, showed similar hardness values to the specimens that Worner water-quenched from 950°C. The hardness curve the authors obtained shows a more pronounced peak, but in other respects it is very similar to Worner's curve (Fig. 1). While it was possible to make fairly reliable measurements of the percentage of martensitic a in quenched powders (by Geiger spectrometer), the solid samples allowed only approximate estimates to be made from visual observation of line intensities on film. Retained ? begins to appear in quenched lumps containing 0.2 pct Fe; at 2.2 pct Fe there are approximately equal quantities of ß and a'; in a 4.7 pct Fe alloy only a trace of a' appears. These results are represented as a curve on Fig. 1. The hardness and constitution of powder samples were verified by repeating both types of quenching experiment described in the earlier paper.' Identical results were obtained by the two methods, and they agreed with the figures published previously (Fig. 1). The appearance of the martensitic structure under the microscope is shown in Figs. 2 and 3. The mar-tensite needles are coarser in the lump; otherwise the structures are similar. Three conclusions are made at this juncture: 1— The properties of quenched lumps reported by Worner are confirmed, on the whole. The differences between them and the properties of powders are probably due to an effect of specimen size. Differences of behavior in various sizes of specimen have been observed previously in martensite reactions in Fe-Mn alloys3 and in Cu-A1 alloys. 2—The maximum hardness of both quenched lumps and quenched powders appears at a composition where martensite formation has all but ceased. In this respect, powders and lumps behave similarly. 3—Martensitic a' has essentially the same microscopic appearance both in powders and lumps. Acknowledgment This work is part of a program sponsored by the Defegce Research Board of Canada, Project No. 425.

Jan 1, 1956

By W. M. Baldwin, C. R. Johns

Cobalt is reported1,2 to scale in accordance with the Pilling and Bed-worth3 parabolic law: where w = weight increase per unit surface area K = constant l = time The reported values of the parabolic oxidation constant, K, in the temperature range 600 to 1100°C follow an Arrhenius type of equation as inspection of Fig 1 shows. According to Valensi's theory5 on the scaling of metals where multiple-layered scales (for example, MeX, MeX2, and others) are possible, this fact could be construed as indicating that a single oxide only is formed on cobalt in this temperature range. Since the single straight line extends above 920°C where only CoO is stable in air (see Fig 2) it might be inferred that this is the only oxide formed on scaling. Arkharov and Voroshilova10 have studied the scales formed when cobalt is heated in air in the temperature range 385 to 800°C and report that CoO is indeed found in the scale but that CoO4 is also found as an overlay and in increasing amounts in the lower temperature ranges. No quantitative data regarding the relative proportions of the two oxides were reported. Again in the light of Valensi's theory this would indicate that the straight line in Fig 1 would be expected to undergo an inflection at some point in the temperature range 385 to 800°C. Chauvenet2 has studied the oxidation rates of CoO to Co3O4 and has found this reaction to proceed parabolically with time but reports parabolic scaling rates which are considerably (about ten times) larger than the scaling rates of cobalt metal itself. This is difficult to explain in terms of Valensi's theory although a full discussion of the possible discrepancy cannot be made in view of the lack of sufficient data. These points made an investigation of the scaling behavior of cobalt in air an attractive study. Discussion of Results Relatively large (approximately 95 sq cm of surface area) samples of 0.020 in. thick electrolytic cobalt strip,* sanded with 2/0 paper, were heated in air in a cyclone type furnace. The samples were weighed before and after the scaling treatment. The weight increases so observed obeyed the Pilling and Bedworth parabolic law at all temperatures studied. The parabolic scaling constants when plotted on a logarithmic scale as a function of absolute temperature are reproduced

Jan 1, 1950

The Atlanta Mine is located in east central Nevada, in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of the old mining town of Pioche. From this famous district, high-grade copper ore was mined and shipped to a smelter in Wales in the 1850s; an early day lead blast furnace was also in operation. The Standard Slag Company began operations in May 1975 on the well known Atlanta Mine, which was operated by Roy Hardy in the 1930s. The mill is currently processing 450 mtpd (500 stpd) of gold-silver bearing ore. Mining by open pit is in a brecciated zone occurring between limestone-dolomites on the foot wall and tertiary rhyolites on the hanging wall. The quartz breccia is considered among the most abrasive in the world - shovel teeth must be replaced every week. Stripping ratio is 3.9 to 1.0. Because of the hard abrasive ore, the crushing plant consists of four units: two jaw crushers in series, one Hydrocone, and one Gyradisc. Mine feed to the primary crusher is limited to 610 mm (24 in.) in size. The remaining crushers work in closed circuit with screens to produce a mill feed of 6 to 13 mm (0.25 and 0.50 in.). Hardness of the ore is demonstrated by the fact that the reversible liners of the primary jaw crusher had to be replaced in early 1978 after handling only 39,000 mt (44,000 st) at a cost of $0.095 per mt ($0.086 per st). Another example of the extreme abrasiveness of the breccia ore was the total cost per ton in 1977 for all wear parts in the comminution circuit, including screens and grinding media. This amounted to $2.84 per mt ($2.58 per st). The Atlanta grinding plant consists of three ball mills to grind the 7 mm (1 /4 in.) crushing plant product to 85 to 90% minus 150 microns (100 mesh). Feed rate to the primary Tricone mill is determined by maintaining a cyclone overflow at 28 to 38% solids, which controls the grind mentioned above. A mixture of 90 and 65 mm (3.5 and 2.5 in. ) balls are charged to this primary mill. Both the secondary mills are charged with 50 mm (2 in ) balls. Total ball consumption is 2 kg per mt (4 lb per st). All three ball mills use rubber liners. Primary mill cyclone underflows are fed to the secondary mills close circuited with the same cyclones.

Jan 1, 1981

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphate from the soil. Man's most important use of phosphate is for fertilizer; however, he is also a heavy user of many industrial phosphate chemicals. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and saltwater. The average content in rocks is 0.1 to 0.2% P2O5, as documented recently by McKelvey (1973). About 200 minerals contain more than 1 % P,O,. However, the important one in igneous rocks is fluorapatite, (Ca,(PO,) ,F) containing about 42% P,O, and 3.8% F,; in sedimentary rocks the one important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO,. Both are in the apatite family of minerals. The mineralogy of phosphate minerals was reviewed recently by Altschuler (1973). Although phosphate occurs in nearly all rocks, economic recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade and must be concentrated.

Jan 1, 1975