Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

John S. Kennedy, Chamhersburg, Pa. (communication to the Secretary): The washing-plant described by Mr. Johnson is a good illustration of the advantages derived from a well-designed and care-

Jan 1, 1895

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

By F. Twyman, D. M. Smith

THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928

By Arvid E. Nissen, Knox Taylor, John H. Hall

Some months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter he had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908, and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel. A brief examination of the tests in Table 1 shows that certain treatments of, for instance, 0.30 per cent, carbon steel are not represented by any test data. Had this been a laboratory research, this information would undoubtedly have been furnished, but as this work was done for commercial purposes the omissions are due to the fact that, at the time the work was done, we saw no advantage in trying every composition of steel with each treatment discussed in the paper.

Jan 1, 1920

By CHARLES F. DEISS

The total pipe-line runs of petroleum in Indiana during 1945 were 4,114,000 bbl., a decline of nearly 17 per cent below the estimated 4,950,000 bbl. produced in 1944. Drilling activity during the year was centered in Posey and Gibson Counties, where seven new pools were discovered in the state. Four of the pools are in Posey County-Crunk, Farmersville, Jeffries and St. Wendells East-and the other three are in Gibson County-Johnson West, Lysle and Mt. Carmel East.

Jan 1, 1946

By N. V. Melnikov, L. N. Marchenko

The latest theoretical and experimental study of physical processes initiated by explosions in solid media have made it possible to obtain a deeper insight into the mechanism of the energy transfer to ambient rock from char es of explosives interspersed with various air gaps. As shown in (17, high explosive action causes excessive fragmentation of medium in the vicinity of the charge, while expansion of the process into the massif is negligible. A theoretical outline of a more rational application of explosion energy was given with a view of obtaining more uniform fragmentation of rock convenient for loading and transportation. The proposed idea proven by experimental study consisted of the possibility of explosion control based on redistribution of explosion energy. Practical realization of the above idea was proposed (1) involving charges with air gaps for rock fragmentation. Since the Rolla Symposium on Mining Research (USA, 1961) (2), borehole charges with air gaps have become common practice. This method of rock blasting is applied in open cast and underground mines working the hardest and viscous, hard, medium hard and soft rocks (ore, quartzites, granites, 1 imes tones, sandstones, coals, etc.) as well as at enterprises for extraction of building materials and raw chemical minerals of any strength. Application of charges with air gaps results in an increase of the degree and uniformity of fragmentation (up to 94 percent of the blasted rock mass consists of fragments not exceeding 400 mm), the average fragment size decreases by 1.5-2 times and the amount of lumps is reduced by 2-10 times (in some cases there are no lumps at all ). Besides, the amount of operation for filling boreholes with tamping material is reduced, the specific consumption of explosives

Jan 1, 1971

By W. F. Flanagan, K. R. Evans

The strong temperature dependence of the flow stress of bcc metals has prompted considerable interest and controversy concerning the rate-controlling influence of the Peierls' mechanism upon deformation in metals.18"21 Dorn and Rajnak" recently offered a criterion for Peierls' deformation utilizing a line-energy model of a dislocation to estimate the saddle-point activation energy, for the nucleation of a pair of kinks as a function of applied stress and the height and shape of the peierls9- barrier. It was found that Un/2Uk, where 2Uk is the excess energy of a kink pair, was a unique function of where is the effective stress and 7p is the Peierls' stress as defined in Fig. 20. The relationship found by Dorn and Rajnak between is given by the solid line of Fig. 21. may be expressed in terms of the temperature of test, T, and the athermal temperature, T,, defined in Fig. 20. Considering the strain-rate, 9, of deformation for a thermally activated process to be given by where fo is nearly a constant, it is seen that and the theoretical relationship of Fig. 21 may be examined with readily obtainable experimental parameters. Dorn and Coworkers analyzed a large amount of experimental data in this manner for materials sus-

Jan 1, 1967

By William Marsh Baldwin

[Two of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Hencky1-3 and the St. Venant7-10 equations. HUBER-VON MISES-HENCKY EQUATION The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,? al, a2, and a3 satisfy the equation: (s1 - s2)2 + (s 2 - s 3)2 + (s 1 ? s3)2 = 2K2 [I] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities a1, a2, and a3 are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4,5 (Fig. I). The radius of this cylinder is v2/3K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values s 1/K = si, s 2/K = s2, s 2/K = s3 to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (s1 - S2)2 + (S2 - S3)2 + (Sl - S3)2 = 2 [2] and the radius of the cylinder becomes 2/3v. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elastically, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates s1, s2, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordi¬nate axes). Let us now pass a line through the point on the circle and the point on the axis.]

Jan 1, 1946

By S. F. Frederick, G. F. Pittinato

The deformation mechanisms operating in Ti-5Al-2.5Sn at 20°K under uniaxial and biaxial stress fields were determined by using both optical and electron microscopy. In the uniaxially stressed specimens, de-fu~rnation twins were found only in the immediate vicinity of the fracture. Twinning was, however, established as a deformation mechanism under biaxial stress conditions. The same slip systems were opera-tiz,e under both uniaxial and biaxial stress. Prismatic slip was identified as the major slip syslem; however, basal and first-order pyramidal slip also occurred, but to a lesser degree. The interaction of moving dis-locations on intersecting slip planes resulted in the formation of jogs and dipoles. Hexagonal dislocation networks were formed only under biaxial stress conditions. A discussion is given on the formation of hexagonal dislocation networks. IT has been shown that titanium alloys can exhibit unusually high strengths when tested in a biaxial stress field.'-" The high biaxial strengths are a consequence of a strong basal plane sheet texture which results in distinctly anisotropic flow properties. This texture strengthening appears to decrease with decreasing temperature2 and would seem to indicate a change in deformation modes. For example, in a uniaxial tensile test, Ti-5A1-2.5Sn yields isotropically at 20°K but is strongly anisotropic at room temperature. The increase in biaxial ultimate over uniaxial strength at 20°K is also much less than at room temperature. It is known that titanium car] form deformation twins more readily at cryogenic temperatures than at room temperature.4 Since the formation of deformation twins will reduce the degree of basal texture in sheet material,' an accompanying decrease in texture strengthening would be expected. To investigate more fully the nature of texture strengthening at cryogenic temperatures, the deformation modes of Ti-5A1-2.5Sn tested in uniaxial and 1:1 biaxial tension at 20°K were studied by optical and electron transmission microscopy. EXPERIMENTAL PROCEDURE The uniaxial and biaxial stress test specimens were prepared from 0.020-in. thick sheets of Ti-5A1-2.5Sn ELI having the composition shown in Table I. Uniaxial stress conditions were obtained by using flat tensile specimens machined from the sheet material. The longitudinal axis of the tensile specimens was aligned perpendicular to the rolling direction of the sheet. Tile biaxial test specimens were prepared by rolling precut, 19-in.-lengths of sheet into 4-in.-diam cyl- inders. Following longitudinal butt welding, the cylinders were stress relieved at 1000°F for 4 hr. A 9-in. sq "window" was then chemically milled into each cylinder's surface reducing the wall thickness in the milled area to approximately 0.006 in. The testing procedure consisted of pressurizing the cylinders while simultaneously applying a tensile load. Using this technique, a 1:l axial to hoop stress was obtained. Complete details of the specimen and testing procedures are given in Refs. 1 and 2. The biaxial and uniaxial stress specimens were all tested in liquid hydrogen. Specimens for electron transmission microscopy were prepared by first chemically milling to a thickness of about 0.001 in. followed by electrolytic polishing to electron transmission thickness. The chemical milling solution, consisting of 800 ml of water,

Jan 1, 1970

By Harold Price

PRIOR to Sept. 1, 1928, there had never been constructed what might be termed a long pipe line with electric-welded field joints. Nevertheless, by Sept. 1, 1929, within the period of a year, more than 2500 miles of electric-welded lines have been completed. These lines vary in diameter from 6 to 20 in., and in length from 50 to 700 miles. Before Sept. 1, 1928, no such line had been constructed .longer than 50 miles, and only one of nearly that length, a 40-mile 7-in. gas line in Louisiana. This was in reality the first pipe line to use electric-welded field joints. During the past year the following lines have been electric-welded by the Welding Engineering Co. alone: Texas Pipe Line Co.-157 miles of 8-in. line from Corsicana, Texas, to San Augustine, Texas. (This was the first electric-welded oil line.) Texas Pipe Line Co.-80 miles of 8-in. from Lafors, Texas, to Childress, Texas. Texas Pipe Line Co.-39 miles of 10-in. from Monahans, Texas, to Jal, New Mexico. Texas Pipe Line Co.-50 miles of 6-in, from San Antonio, Texas, to San Marcus, Texas. Texas-Empire Pipe Line Co.-424 miles of 12-in. from Cushing, Okla. to Chicago, Illinois. In addition to the field welding mentioned above,1 250 miles of 12-in. line was electric-welded into double joints at the pipe mill at Indiana Harbor, Ind.

Jan 1, 1929

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By G. F. LOUCHLIN

A FEATURE of the International Geological Congress to be held at Pretoria, South Africa, in the summer of 1929,. will be a symposium on the gold resources of the world. In this connection the U. S. Geological Survey and Bureau of Mines have been asked to prepare a report, showing production in the United States, describing the geology of its principal gold- producing districts, and estimating reserves (a) assuming a continuation of presen6economic conditions, and (b) assuming lower costs. This report will not be completed before April 1, but data thus far assembled are here presented with the hope of profiting by discussion and by information from those well informed on any of the important gold-producing districts. Gold production in the United States rose to a maximum exceeding $100,000,000 in 1915 and then rapidly declined to about $52,000,000 in 1920. Since then it has fluctuated, but on the whole slightly declined. Reviews of the eight leading states afford the following tentative conclusions :

Jan 1, 1929

By AIME AIME

TWENTY-TWO sections and all four of the divisions sent delegates to the annual meeting. They became so interested in the wide ranging dis6ussion of old and yet ever-new problems of Institute affairs that three instead of two sessions scheduled were necessary. Monday morning the meeting assembled with President Bassett presiding in the absence of President-elect Tally, who had been called to Baltimore by the serious illness of a brother. Thursday morning Vice-president Turner presided until Mr. Tally appeared after which the latter guided the sessions. Since reports from all of the active sections save one had been mimeographed and sent in advance to the delegates, detailed reports from each were dispensed with. The discussions dealt largely with membership problems, both local and national, with financing, speakers and programs, visits from national officers, and the conduct of the annual meeting. Many interesting and constructive suggestions were made and will be reported back to the sections by the delegates.

Jan 1, 1931

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

As a result of using copper-containing scrap in the steelmaking process, the copper content of steels has been steadily increasing for years. Consequently the possible role copper may play in the steelmaking process and in the finished product begins to attract the metallurgists' attention. Some time ago one of the present authors forwarded the idea—based on the results of the analysis of nonmetallic inclusions extracted electrolytically from steels—that sulphur in plain carbon steels is distributed mainly between copper and manganese, the amount of iron sulphide being very small; and that, consequently, the problem of copper and that of sulphur in steel cannot be treated separately.' At the time of the publication of the quoted paper little was known about the relative affinities of copper and manganese for sulphur at high temperatures except that at moderate temperatures (below 1000°C) the affinity of manganese for sulphur is much greater. To gather more experimental data on this subject, the present authors undertook the investigation of the equilibrium constants of the reactions: 2Mn(8 or 1) + S2(g) = 2MnS(s) 4Cu(s or 1) + S2(g) = 2Cu2S (S or I)* 2Fe(s) + S2(g) = 2FeS (s or 1) over a range of temperatures wide enough to establish the dependence of these equilibrium constants on temperature. From the equilibrium constants (K = l/Ps2) the free energy of formation (affinity) can be calculated from F° = -RTln 1/PSt (1) where the standard conditions chosen are: 1 atm of sulphur pressure and the activities of condensed components equal one. The decomposition pressure, Ps2, of sulphur over the respective sulphides is too small to be measured directly, but there is a way of eliminating this difficulty by measuring the equilibrium constant of the reaction between the sulphide and hydrogen. From the latter and from the equilibrium constant of the thermal dissociation of H2S we then calculate Ps2 for the respective sulphide. 2Mn + 2H2S = 2MnS + 2H, 2H2 + S2 = 2H2S_________ 2Mn + S2 = 2MnS The numerical values of the equilibrium constant of the thermal dissociation of H2S at different temperatures were taken from Kelley's paper, "The Thermodynamic Properties of Sulfur and its Inorganic Compounds."² In previous experimental work published by Jellinek and Zakowski3 and by Britzke and Kapustinsky4 the equilibrium constants of the reactions Metal sulphide + H2 = H2S + metal were determined by passing hydrogen, at different rates of flow, over the sulphide, analyzing the resulting H2S + H2 mixture and then extrapolating the H2S/H2 ratio (which is a function of the rate of flow) to the zero speed of flow, a method necessarily involving considerable uncertainty. In the present work the equilibrium ratio was actually measured instead of being extrapolated. The apparatus is shown in Fig 1. Experimental Procedure The sulphides were prepared by the following methods: FeS Powdered iron which had been reduced with hydrogen (ferrum reduc-tum) was mixed in stoichiometric ratio with sublimed sulphur and carefully ground. The mixture was put into an alundum crucible, covered with pure sulphur, and the reaction started by touching the mixture with a glowing iron rod. After the reaction was completed the product (still containing some metallic iron) was again ground with sulphur, put into a Rose crucible, covered with sulphur, and heated in a strong current of pure hydrogen. Analysis of the final product showed 62.46 pct Fe and 36.59 pct S. Theoretical for FeS: 63.53 pct Fe and 36.47 pct S. MnS Manganese sulphide (precipitated and carefully washed with distilled water containing H2S) was dried in a Rose crucible in an atmosphere of H2S and heated in a current of hydrogen for 2 hr at red heat. The product was then ground and ignited for several hours at 1000°C in a current of hydrogen sulphide. Analysis showed 64.53 pct Mn and 36.63 pct S. Theoretical: 63.15 pct Mn and 36.85 pct S. Some MnS samples were prepared from metallic manganese and sublimed sulphur by mixing and grinding them and then heating in a current of hydrogen sulphide in an alundum tube.

Jan 1, 1950

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By N. H. Emmons

(Canal Zone Meeting, November, 1910.) AN interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at this plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory., Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaces. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top was necessary and the engineering force was started oil the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of cast copper, but the heat was so great that the copper bent readily, due to the jarring of its * General Manager, Tennessee Copper Co.

Feb 1, 1911