Search Documents

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By Betty L. Gibbs

A company must have an organized approach to effectively sort through the profusion of available software and hardware and find the programs and equipment which fit defined needs. The selection process must build a complete compatible system which includes hardware and software. The methodology presented in this paper helps identify some of the more important considerations. The steps needed for an organized approach to software/hardware selection are: •All involved staff should contribute to an assessment of current computer capabilities and projection of future needs. •Alternatives are analyzed to determine what software and hardware is available and how selections may possibly be merged into the existing computer system. The evaluation process focuses on details of program capability and hardware compatibility. Analysis must be done to determine how closely individual programs fit the established requirements. The final decision is often a balance of needs between program capabilities and hardware availability. Any programs selected must be able to run on existing and newly purchased hardware. Any additional hardware selected must be capable of meshing with the available computer system.

Jan 1, 1983

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By J. H. Schulman, M. H. Buckenham

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By C. Dinis da Gama

Because of the growing importance of back analysis for the interpretation of rock slope failures, particularly in open pit mines, it is suggested a methodologic sequence of activities for dealing with those problems. The principal mathematical tools for the interpretation of the most common mechanisms of slope failures are reviewed, including methods of stress and strain analysis, which seem to be more powerful for parametrization studies, and for developing more realistic explanations of slope behaviour, such as the measurement of displacements. An application of those methods is described, using slope failures detected in a Brazilian uranium mine (Cercado), thus providing reliable shearing strength parameters for the rock mass discontinuites, which were used in the final pit design. The concept of using backanalysis results to supply input data for pit design was implemented by means of the excavation of an experimental trench within mine limits, where specific instruments were installed, and several slope failures were monitored and backanalysed, in order to yield information about sliding mechanisms in the future open pit.

Jan 1, 1983

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,1 later as agalmatolite,2 and finally as pyrophyllite,3 has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,4 which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments.

Jan 1, 1958

By A. O. Dady

PRODUCERS of both bituminous and anthracite coal have for many years been worrying about the gradually decreasing consumption of their product in the United States. Twenty years ago production had climbed to a peak of 569,000,000 tons of bituminous and around 90,000,000 tons of anthracite. In 1939 it was about 393,000,000 tons of bituminous and 51,000,000 tons of anthracite. This does not mean that the country is using less polver than it did twenty years ago, or that we are living in colder buildings. As a matter of fact, about three times as much electric power is now being consumed as in 1920. In general two factors are responsible for the drop in coal consumption: (1) greater efficiency in the use of coal, and (2) increased competition from hydro power, internal-combustion engines, and substitution of oil and gas for coal in conventional furnaces. As to the first factor, it took 3 Ib. of coal to generate a kilowatt-hour of electricity in central stations in 1920 and it takes 1.4 Ib. now; it took about 175 Ib. of coal in railroad locomotives to haul 1000 long tons a mile in 1920 where it talces about 120 lb. now: and marked economies have also been made in the use of coal in steel plants: in by-product coke ovens, and in other large uses. As to the second factor, three times as much electricity is produced from water power now as was produced in 1920; three times as much oil is being consumed in various ways; and likewise, the consumption of natural gas has tripled- whereas coal consumption in the same period has dropped by 40 per cent

Jan 1, 1941

By Harvey N. Davis

MUCH has been written and said during the last twenty years about the place of the engineer in modern life, about the fundamental role that he plays both in developing and in maintaining the material foundations of modern civilization, about the advantages, and also the dangers, of the machine age that he has inaugurated, about the Frankenstein problems that he has unconcernedly foisted upon a generation utterly unable to cope with them, and about the obligation that rests upon him to stop inventing machines and turn his almost legendary energy and skill to inventing institutions that will constitute a solution of the problems he has raised, and contrariwise about his utter inability to offer wise or useful counsel in fields outside the narrow boundaries of his technical training.

Jan 1, 1938

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By A. H. Larson, L. G. Twidwell

DURING the roasting of zinc sulfide concentrates and by-product recovery from flue dusts, the zinc sul-fate phase may occur in various stages of the processes. In addition to zinc sulfide, other sulfide phases are usually present such as CdS, PbS, CuzS, and FeS. Consequently, the effect of these sulfides on the thermal decomposition of ZnS04 was investigated. Merck high-purity, anhydrous zinc sulfate was used as the starting material. The sulfate was heated under an argon atmosphere, at a rate of 10°C per min. With the first slight indication of decomposition as determined by gas analysis, the sample was removed from the furnace and allowed to cool. X-ray patterns showed no other phase present. It is estimated that less than 0.05 pct of the ZnS04 decomposed. The metal sulfides were also heated under an argon atmosphere to drive off any adsorbed water. The materials were then sized (-200 to +270 mesh), mixed in predetermined mole ratios, and pressed into pellets. The experimental measurement of the reaction rate consisted of purifying the argon carrier gas, continuous flushing of the heated reacting mixture with argon, and collection and analysis of the SOn product gas. The reaction system was heated to 600°C and al-

Jan 1, 1967

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961

By E. J. Bonet, P. B. Crawford

It is fairly common practice to reinject water into the aquifer near the oil-water interface in water-drive reservoirs. There have been many studies of aquifer behavior without reinjection,l-5 but apparently no analytical studies have been made to indicate performance when injection wells are present in the aquifer. The diffusivity equation may be used to describe the pressure behavior in an aquifer. When sources are present it can be written as A general solution of Eq. 1 may be obtained as the sum of two solutions. One is a general solution of the homogeneous equation, obtained by dropping the source term in Eq. 1 and still satisfying the required boundary conditions. Another is a general solution of Eq. 1 satisfying homogeneous boundary conditions.1° The first solution, which corresponds to the aquifer without reinjection, has been given quantitative and qualitative treatment in the literature.l-5,8,9 The latter solution will be treated here. Solutions with variable injection rates are obtained by superimposing solutions with constant rates, so we have considered only the latter. Five cases have been treated here: 1. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The pressure along the line x = 0 is maintained at zero pressure. (See Fig. 1.) Equations showing the pressure distribution, rates, velocity and cumulative influx have been developed. Certain numerical results are shown. 2. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The rate of production along the oil-water water contact is maintained constant. Equations showing the pressure distribution inside the aquifer are presented. 3. A linear aquifer of finite width and extent. Constant pressures are maintained at opposite ends of the aquifer. Water is injected at constant rates at point xo, yo. Equations showing the pressure distribution are shown. 4. A linear aquifer of finite width and infinite extent. The pressure is maintained constant at the oil-water contact. Water is injected at a constant rate at point xo, YO. 5. A linear aquifer of finite width and finite extent. The pressure at the oil-water contact is maintained constant. Water is injected at constant rate per unit length along a line x,. The Linear Aquifer The linear closed aquifer, performing at constant terminal pressure was selected as the first case to be analyzed. The development of the equations is based on uniform injection per unit of thickness, and gravity effects are neglected. In practical application this condition is probably most closely achieved when the

Jan 1, 1970

By Ivan Simon, R. K. McConnell

Anticipating the availability of tiltmeters suitable for use in boreholes, this article proposes a method of using one or more of these meters to determine in situ stress distribution before and after mining operations. Several ways of using relief techniques to measure in situ stresses in rocks have been developed. These techniques, summarized by Merrill,1 involve measuring deformations which take place when a specimen of rock is wholly or partially isolated from the stress field in the surrounding rock. Measurements of rock deformation caused by stress relief from mining operations can, in principle, also be used to estimate in situ stress distributions. Müller2 has mentioned experiments being carried on in Austria with a "deformation indicator" to determine the tilting of holes drilled before a mine opening is made. Similar work using borehole extensometers has been reported by Potts? and Duvall4 has called attention to the possible use of tiltmeters in making these measurements. Considerable attention is now being paid to the use of tiltmeters in detecting rock deformation associated with fault movements, earthquakes, earth tides, etc. The instruments used for these measurements have usually been of the mercury tube, water tube, or quartz fiber type, but because of their large size, and/or fragile nature, such instruments would not be suitable for use in mining stress measurements. Recent instrumentation developments, however, give promise that rugged, sensitive tiltmeters small enough for use in boreholes may soon be available.' In anticipation of these developments, this article presents a number of calculations of the possibility of using one or more tiltmeters emplaced in a drill hole prior to mining operations to determine the in situ stress distribution both before and after a mining operation. Consider point p (x, z) near a tunnel of radius a

Jan 1, 1969

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968