Search Documents

By W. E. Forsythe

WHEN measuring ordinary temperatures, the instrument is generally placed in very close contact with the body the temperature of which is desired. However, if the temperature of the source is continually raised, a point is soon reached where no known substance will, in general, remain constant in any of its temperature-measuring properties if placed in direct contact with the source. Also, it is occasionally necessary to measure the temperature of a source that 'is so small or so situated that it would be very hard to bring the measuring instrument into direct contact with the source. When these conditions exist, advantage is taken of the well-known fact that all bodies, when at sufficiently high temperatures, send out radiation in amounts readily measurable. This radiation has been found to be related to the temperature. The temperatures of very hot bodies have probably always been judged by the color, or the brightness, of the light given off. With practice, one can estimate probably within 50° to 100° C. of the correct value. However, if judgment is left to the eye alone, very much larger errors are sometimes made, due to

Jan 9, 1919

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

Jan 1, 1922

Jan 1, 1922

By Richard S. McCaffery, Morrison B. Yung

While assaying some copper carbonate ore from the Frazer claims, Similakameen, B. C., I noticed that on parting the gold button a deep orange solution was formed. The button gave off pink bands in the nitric acid, which became deep orange at a short distance from it; and as it traveled over the surface of the porcelain dish, it left a deep orange track behind. As the button brightened in the cupel, it appeared to have a bronze color; but I have since found that when amarillium is in large excess of the gold, the button is a very dark gray. The button parted easily. To the orange solution I added a salt (NaCl) solution, shook in a silver testbottle, and filtered. With H2S I obtained a precipitate, which I supposed due to platinum. However, on further tests, it did

Jan 1, 1903

By CARL B. SNYDER

PERHAPS the most extraordinary thing about business, the trade and production of the country as a whole, is its amazing continuity and growth, its momentum and energy. It goes on year after year, growing steadily, almost without breaks, in spite of every kind of disturbance. We have been grossly deceived into the idea that business is highly variable. We have taken a few things like pig iron, and the like, constructional activity broadly, and imagined that these are a trustworthy measure of trade. Actually they are the worst that we could find. They do not apply to more than 10 per cent or, at the most, possibly 15 per cent of the total of the country's industrial activity. The other 85 or 90 per cent, or even more, goes on growing surely and steadily just like the growth of population and the steady advance in technique, invention, discovery, and improved methods of production Let me give you what seems to me one of the most remarkable examples of this amazing momentum and regularity. You know that 90 per cent or more of the business of the country is done 'by means of checks. About seven-eighths of the total of all checks drawn are reported regularly every week in the newspapers. Let us follow these reports from week to week, just as they come, and plot them up against the correspond- ing weeks of last year, and the year before, and the gear before that, as far back as you would like to go. Take especially the figures for 140 selected cities out- side of New York.

Jan 1, 1929

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,' which had been used since the early 1930's by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell's plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell's practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By John Johnston

WHEN I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in 1916-that is, about 25 years ago-in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father ¬Dr. Samuel Gridley Howe, his mother-Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature. is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-carbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable, tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass . . . by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes-and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. It tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works "f the watch was the best butter. If the reader learns no more than to beware of attempts to decipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By Alan Morris

Season cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes arc fairly well understood and means for its prevention are inexpensive and effective, so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,' in discussing a paper by Hatfield and Thirkell, says: " He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultaneous corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack. Dr. McAdam3 has investigated the effect of corrosion on the fatigue limit of brasses, among other materials. He directed a stream of either fresh or salt water against the specimen while it was undergoing fatigue test. The corrosion-fatigue limits thus determined may be considerably lower than the endurance limit without coincident corrosion. The exact

Jan 1, 1930

By R. C. Gifkins, A. Gittins

A. Gittins and R. C. Gifkins (University of Mel-houvne)— Evidence from somewhat similar experiments to those described in this paper has led us to the conclusion that possibility 2) of the four listed on p. 319 is a description of what happens in grain boundary sliding. That is, sliding is limited by accommodation deformation, it being necessary to the Continuance of sliding that this accommodation should take place. An example of such accommodation, though probably not the most important, is fold formation at triple points. The evidence and arguments for this point of view are set out in Refs. 14 to 16. In particular, an experiment with a lead bicrys-tall5 seems to support point 2) rather than 3). In creep of this specimen it was found that at least 90 pct of the extension of a zone 0.3 mm wide at the boundary was supplied by sliding at the boundary. The sliding was localized in a region at the boundary very much smaller than 0.3 mm, in fact, in a region too narrow to resolve optically. In poly crystalline Specimens&apos; there appears to be a surface effect, as found by Rachinger," but it appears that this may not manifest itself at low strains. "Low strains" means <10 pct for a Pb-TI alloy, <2.5 pct for magnesium or "Magnox" A12 alloy, or <40 pct for a 0 brass. Up to this extension the sliding, measured by the mean vertical step at boundaries, is proportional to extension. We are able to say this with some confidence, since the error bars on our points are statistically derived. Our results would lead us to think that the error bars on other work, including that of Mullendore and Grant, are much too large at low strains to show this

Jan 1, 1963

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By W. H. Hoffman

During the autumn of 1891, several heavy blasts (each throwing down some 3000 tons of ore) were made on what is known as the Theall side of these mines. Immediately after one of these blasts, the writer found that at least one-third of the ore was largely impregnated with pyrites, and besides this, fully 15 per cent. of the entire blast was composed of irregular lumps of magnetic pyrites. This was a revelation wholly unexpected, as previous examinations by many experts had failed to disclose any such quantity of sulphury ore. Over the center of the Theall tunnel there suddenly appeared a perfect keystone, as it were, of pyrites, 3 feet wide at the arch of the tunnel, 13 feet ride at the top, and 20 feet high. This keystone pinched out in February, 1892; but in that month large blocks of pyrites were more plentiful on or near the western wall, and these deposits extended the entire height of the workings, some 43 feet. The second blast in November, in the face and over, and on each side of the tunnel, was far more surprising. The whole cross-section it exposed was thickly interspersed with layers of magnetic pyrites, ranging in thickness from 10 to 24 inches, and quite irregular in form, while all of the ore carried much more than the usual amount of sulphur in the non-magnetic pyrite. One hundred and fifty-five tons from a portion of this breast (western side), showed the following composition upon sampling and analysis: Per cent. Metallic iron,...45.080 Phosphorus,..........304 Sulphur,...........23.510 And the balance of the blast showed: Per cent. Metallic iron,.....• 33.210 Phosphorus,...........349 Sulphur,.......... 6.680 vol. xxI.-33

Jan 1, 1893

By George H. Anderson

A CHAPTER of appealing interest was added to the industrial history of the Southwest early in June, when the War Production Board gave final approval to the erection of a blast furnace, a battery of coke ovens, an ore-beneficiation plant, and other facilities for the production of pig iron in northeastern Texas, just north of the East Texas oil field. For many years the people of Texas and adjoining states have cherished the ambition and desire that eventually an iron and steel industry drawing upon local mineral resources would be established to serve Southwestern markets. The existence in this vicinity of valuable deposits of iron ore, limestone, and coking coal has been known in a general way for many years, and efforts have been made from time to time to use them in the production of iron. The present development promises to bring to realization the dreams of the men who have visualized what the establishment of this basic industry would mean to the region.

Jan 1, 1942

By John Devine

DURING the past few years the Bureau of Mines has been studying hydrogen-sulfide corrosion in the petroleum and natural-gas industries. Early work was confined to investigating the various practical, or operat-ing, factors that control the corrosion reaction when ordinary mild steel is being attacked. In that work it was shown that, if the optimum operating conditions1 are obtainable, . gas containing hydrogen sulfide can be handled at ordinary temperatures without serious corrosion resulting. However, frequently "sour" gas must be handled under other than optimum operating conditions, and combating corrosion then becomes a problem to be considered more during the construction of a system than during its subsequent operation. That is, where economi-cally practicable in such cases the designer will seek to substitute for mild steel other steels or ferrous metals more resistant to corrosion by hydro-gen sulfide. The comparative resistance of various commercial steels and alloy steels to corrosion by hydrogen sulfide at elevated temperatures has been reported systematically by previous investigators,2 but similar information for corrosion at ordinary temperatures is available only from scattered sources, representing different methods of testing. As the value of comparative corrosion tests depends largely upon the use of a

Jan 1, 1934

By N. A. Gokcen, John Chipman

D. C. Hilty (Union Carbide and Carbon Research Laboratories, Niagara Falls, N. Y.)—This paper is a very nicely detailed analysis of a difficult problem. I would like to point out that the results that Mr. Crafts and I published a few years ago had no reference to activity, or anything else of a similar nature; our results were strictly empirical. It is quite gratifying that we now have a case where results involving activity coefficients and results derived from direct observations on actual steel melts are practically identical. When two different laboratories, working from two entirely different approaches, come out with results in such good agreement in their major significance, that is an achievement. It is something that was not possible 15 or 20 years ago. There is one question I would like to ask Dr. Chip-man. It has to do with a very minor point of disagreement in these results. When we reported the kink in the Si-O solubility curve I think you may recall that it came at the different temperature levels at about the order of 0.015 to 0.03 pct 0 and 0.03 to 0.07 pct Si—we also pointed out that we had difficulty in obtaining data at that level, although we finally did get some. I note in going through the data for the present paper, that there are no samples in those particular silicon and oxygen ranges. I wonder if that was purely accidental or was there a reason for it. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—Mr. Hilty, do you have any explanation for that discrepancy between Dr. Chipman&apos;s curve and your own Mr. Hilty—Our explanation for it at that time was that for some reason our system probably was not in true equilibrium with SiO, that is, in equilibrium with the silica crucible at that level. We did observe, however, that that was the level at which both the metal and the slag became saturated with SiO,. On the average, in studying inclusion formation in small ingots permitted to solidify normally from the molten state, we observed pure silica inclusions at silicon contents over about 0.05 pct and FeO type inclusions at silicon

Jan 1, 1953

By AIME AIME

A STUDY of subsidence and ground movement in the copper and iron mines of the upper peninsula of Michigan has been made by W. R. Crane of the United States Bureau of Mines and published as Bulletin 295 of 66 pages and 49 illustrations. As a result of subsidence, the country adjacent to the mines and over- lying the mine workings in this district is often broken to such an extent as to affect its value; mine shafts and development openings are occasionally so damaged as to be rendered useless, and water can enter the workings through fractures and cave-ins. The problem is more serious in the iron-mining districts, where villages and towns not owned by the operating companies have grown up around mining operations.

Jan 1, 1929

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952

By AIME AIME

BEFORE proceeding with the papers scheduled for the ore and foundry session*, the teller&apos;s report on the election of officers for the ensuing year was presented, a; follows: Chairman. G.C. F. MacKenzie; vice-chairmen, C.S. Robinson, J. T. MacKenzzie, C. E. Meissner; executive committee, A. L. Field, R. F. Harrington, E. F. Kenney lit. Waterhouse announced that the fall meeting will be devoted to alloy steel. This meeting will be held in Chicago the week of Sept. 22 in connection with the National Metal Congress. He also announced that oxygen in steel will be the central idea of the meeting which will be held in New York next February. The first paper, entitled "Sintering Limonitic Iron Ore at Ironton, Minn.," was presented by Perry G. Harrison (T. P. 284), the author. Sintering was first un¬dertaken in 1024 to treat Cuyuna range iron and manganiferous ores low in silica and high in moisture and containing objectionable qualities of fine... A Dwight-Lloyd machine was first installed. This machine was replaced by a larger one having a width of 72 in. The power cost was decreased from about $11.22 per ton of sinter on a 42-in. machine to about X0.14 for the 72-in. machine. The tons of sinter per man-shift was increased from 11.86 to 16.77. Improvements embodied in the larger plant reduced the cost of sintering to $0.41. The analyses of iron ore and manganiferous ore and the sinter produced from these materials was used to show the increase in value at the mine resulting from sintering. Crude iron ore actually unsalable was increased in value f.o.b. mine from a theoretical figure

Jan 1, 1930

By Charles H. Foreman, James F. McCarthy

The orebodies of the Hecla mine are from 3 to 40 ft. wide, dip not less than 70°, and in most cases are nearly vertical. The Hecla and Intermediate orebodies are generally associated with a lamprophyric dike, usually about 2 ft. wide, but which attains a maximum width of 7 ft. The ore appears on either or both sides of the dike. The country rock is Burke quartzite with no definite walls and a tendency for nearly horizontal, but irregular, quartz stringers to run from the lode into the walls. This latter condition prevails almost entirely in the hanging wall, causing a natural tendency for portions of the wall to "offset" and resulting in an extremely heavy side pressure. The fact that there are no definite walls causes a great variation in the width of the stopes, as stringers will run into the walls for irregular distances. The ore occurs as galena in varying widths and grades. It is often necessary to mine a face having a " horse"&apos; of waste between two stringers of ore. This block of waste might be 6 or 7 ft. wide but with the Hecla method it is necessary to mine the entire face. In this case an effort is made only to shatter the waste, allowing for easy sorting underground. The Hecla mine requires a flexible system allowing for the extraction of ore from varying widths, with the necessity of close filling to give the needed protection from side weight. About 15&apos; per cent. of the material broken in the face is sorted as waste, either at the face of stope, or in the sorting plant. Shafts, Drifts and Crosscuts The outside dimensions of the shaft are 19 ft. 4 in. by 7 ft. 2 in. The shaft consists of three working compartments, two for the hoisting of ore and one for auxiliary work. The working compartments are 5 ft. 2 in. by 4 ft. 4 in. inside measurement. The rest of the shaft is used for pump column, electric cables, and ladderway. (See Fig. 6 for framing of timbers.) The shaft is about 700 It. from the orebody for topographical reasons. Solid formation was not reached in shaft for 80 ft. Timbers in this section became alternately wet and dry on account of seasonal changes

Jan 1, 1925