Search Documents

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. MISFIRES CAUSED BY FAULTY DETONATORS The important part of an electric blasting cap, to the user where multiple shot-firing is done, ass in the steep-pitch, thick-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also to a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented.

Jan 1, 1929

By Peter Beardmore, Michael B. Bever

The effects of the temperature of deformation and the degvee of deformation on the annealing spectrum of a Au-Ag alloy have been determined by vesistance measurements. Specimens were deformed in torsion at 4°, 78K and room temperature up to strains nd/l of about 1.0 and were isochronally annealed. Discrete annealing stages similar to those found for pure metals were observed. Stage A occurred below room temperature; the decrease in reszstance associated with this stage increased as the temperature of deformation was lowered or the strain was increased. Stage B manifested itself as an increase in resistance; this is attributed to the restoration of short-range order promoted by vacancy or vacancy aggregate migration. At temperatures above 48S0K, recrystallization or Stage C occurred. Stages A, B, and C in the annealzng curves of this alloy may be considered to correspond to Stages II, Ill, and V, respectively, in the terminology used to describe the annealing spectrum of pure metals. ThE annealing behavior after deformation below room temperature has been thoroughly investigated on pure metals, in particular gold and copper. The occurrence of several discrete stages in the annealing spectrum of these metals has been established, but the interpretation of some of these stages in terms of specific mechanisms is still controversial.' The annealing of alloys deformed below room temperature has been the subject of only a few investigations. In the investigation reported here, a Au-Ag alloy was annealed after deformation at and below room temperature. This continues a research program on the deformation and annealing behavior of Au-Ag alloys.2-8s EXPERIMENTAL PROCEDURE An alloy rod of composition 82.6 wt pct Au-17.4 pct Ag was reduced to wire, 0.0428 in. diam, by swaging and drawing. After a recrystallization treatment, the grain size was 0.031 mm, as obtained from the average linear intercept.7 The ends of wires about 6 in. long were flattened and sealed into short brass tubes with cold setting cement to form the grips of the torsion specimens. The equipment used for deformation has been described elsewhere.6 The specimens were deformed at room temperature, 78", and 4°K to various strains nd/l, where n is the number of turns, d the diameter of the specimen, and 1 its length between grips. The strain rate ?max was 0.1 min-' at the sur- face of the specimen except where noted otherwise. The specimens were annealed isochronally for 30 min at intervals of approximately 30°K from the temperature of deformation to approximately 800°K, except that after deformation at 4°K the lowest annealing temperature was 78°K. A potentiometric method was used to measure the resistance: all measurements were made at 78°K with the exception of some measurements at 4°K mentioned below. Data obtained with a single specimen yielded a complete annealing curve: in several cases duplicate specimens were used to confirm the reproducibility of the curves. Since the surfaces of the specimens were rough after deformation, their diameters could not be measured accurately. The resistance increments after deformation and annealing are therefore reported as percentages of the resistance of the same specimen measured after completion of the annealing, that is, after full recrystallization. The corresponding resistivity values can be calculated by obtaining the effective diameter of a deformed specimen from the ratio of its resistance after recrystallization to the true resistivity, which was determined with a smooth specimen of known dimensions. This method of calculation was used to obtain data shown in several of the figures. RESULTS AND DISCUSSION The isochronal annealing curves after deformation to various strains at 4", 78K, and room temperature are shown in Figs. 1, 2, and 3, respectively. The resistance increment of the as-deformed specimens as a function of strain is shown in Fig. 4. For the specimens deformed at 4°K. values measured at 78°K are plotted with the exception of those for the as-deformed

Jan 1, 1970

By R. B. Schluter, M. M. Fine

Processes for manufacturing prereduced pellets have heretofore required temperatures of 2100°F or higher. Sulfides will accelerate the liquid-phase sintering of metallic iron, yet do not deter the reduction of iron oxides. The sulfides may be introduced as gases to the kiln atmosphere or as solids in the re-ductants. The net result is that well metallized iron pellets with good crushing strength can now be produced at a little over 1800°F. One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. In May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.' More recently, in November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials at Evian, France, in May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then the current interest in reduction must be at a high level. Barrett,2 one of the early pioneers, stated some years ago that "The history of sponge iron has been so discouraging that many men in the iron and steel industry are violently opposed to giving it any further consideration." In spite of the "violent opposition" noted by Barrett, research people in and out of the industry continue to be attracted by the elusive prospect of uncovering a simple, viable means of direct reduction. Wild,3 one of the speakers at Evian, listed no less than 48 direct reduction processes (laboratory, pilot plant and commercial). Some of these were of historical interest only, but many others had resulted from developments within this decade. The previous big thrust into direct reduction occurred under the artificial impetus of a wartime economy (World War 11) and was largely an effort to provide more melting stock without coke ovens and blast furnaces. The present-day inquiry is proceeding at a more leisurely pace and the emphasis is different. For one thing, there is much less anxiety to circumvent the blast furnace. On the contrary, a whole new research endeavor has grown from the discovery that metallized burdens are exceptionally productive.4 Although the search for a melting stock

Jan 1, 1970

By H. J. Hand

STATISTICAL methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,' written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science,, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should .they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. † Many Useful Statistical Devices Available.-Many statistical methods of attack are available for the analysis of plant data. It is the object of this paper to discuss applications of some of these methods to the solution

Jan 1, 1938

By Charles T. Baroch, Corbin Allardice

Nuclear energy probably has greater potentialities for changing the world's way of life than any other recent discovery. The atomic-bomb bursts over Hiroshima and Nagasaki suddenly changed the concepts of war. Peaceful uses of nuclear energy are advancing so rapidly that no study of economic trends is complete without giving them consideration. The minerals specialist, especially, must be aware of this new force in our lives, as minerals and metals are essential in harnessing the new force, and atomic energy itself is rapidly improving its competitive position in the energy field. Future historians may chronicle December 2, 1942, as the beginning of the Atomic Age. On that day Enrico Fermi and his co-workers at the University of Chicago produced and controlled the first self-sustaining nu- clear chain reaction. Like many inventions, the first application of nuclear energy was as a weapon of war. However, its potential usefulness in man's work and welfare far outweighs in economic importance its destructive use in war, unless its military effect would be considered so great and all-embracing that no major power will hereafter chance a world conflict. Recognition of this potential has generated a vast international effort to exploit the atom for peaceful beneficent purposes. Like its physical manifestation, the advent of nuclear energy has unleashed chain reactions that have pervaded the political, social, and economic environments of the world. The impact of nuclear developments in one of many fields is exemplified by the uranium mining industry. Uranium was discovered in 1789 and in the next century and a half it found only an insignificant use as a ceramic coloring agent; in fact, in the latter part of that period, it was a largely unsalable by-product of the radium and vanadium industries. Up to 1940 the total quantity of uranium metal produced was not more than a few grams, of doubtful purity. Thus the production of 12,400 pounds of pure

Jan 1, 1959

By Z. F. Oszter

This paper discusses the materials handling problems encountered in cement plants in the areas of raw and finished product grinding and cement storage. It illustrates by examples taken from actual installations, how optimum feed rate is maintained in grinding circuits with properly applied bin dischargers (vibrating hoppers, Mexican feed boxes and aerated bin bottoms) for materials with high moisture content and/or difficult handling characteristics. Initial operating problems with the equipment will be discussed and maintenance requirements will be indicated for comparison purposes. In a modern cement plant, properly functioning bins and feeders are as essential as process control, for no process control system, however sophisticated, can perform efficiently if raw materials do not flow into the plant processing facilities at the required time and rate. Most materials used in the manufacture of portland cement - such as silica sand, iron ore fines, crushed limestone, gypsum, clinker or cement itself-have difficult handling characteristics under specific conditions. High moisture content or even dampness due to condensation may create bin hang-ups, arching and ratholing, all of which result in improper functioning of the feeders or proportioning equipment. The occurrence of these problems in existing cement plants spurred a search for the corrective devices discussed in this article. The equipment investigated included bin dischargers in the form of vibrating hoppers for moist raw materials, Mexican feed boxes for clinker and aerated bin bottoms for cement. Operating experience with different types of bin dischargers showed that the actual performance of some did not come up to the expected level under prevailing operating conditions. The aim of this paper is to record the results of this experience and there- by aid designers and/or operators in selecting the most suitable equipment for their requirements. BIN DISCHARGERS (GENERAL) A discharger is a device that causes stored solids to flow out of a hopper without metering the rate of flow as a feeder does. The investigation discussed here encompasses the following types of bin dischargers used in a cement plant: (1) vibrating hoppers (horizontal motion), (2) whirlpool hoppers (horizontal and vertical motion), (3) aerated bin bottoms (air fluidization), and (4) Mexican feed boxes. Most of the bins used in the cement industry are of the plug flow type. Raw materials with difficult handling characteristics such as high moisture content may cause flow problems when fed through small openings (12 x 18 in.), even if two walls of the bin are vertical.' The most appropriate solution to these flow problems would be the installation of separate mass flow bins for the different materials such as silica sand, iron ore fines, crushed limestone and gypsum, with each bin correctly designed from test data obtained by measuring the flow properties of representative samples. However, limited storage capacity and plant space usually preclude this approach. Quantitative design of bins for flow based on measured flow properties of representative samples of the bulk solid to be handled is no longer an "engineering art," thanks to the basic research done on the flow of bulk solids in bins during the last decade.2, Where space limitations exist, however, or where improvements are being sought for equipment already installed, bin dischargers offer a satisfactory solution to flow problems. They can be applied effectively under flat-bottom bins or mounted to existing plug-flow bins with very little modification to these facilities. In both the foregoing cases, plug flow will be maintained, but the flow channel will be considerably increased so that it is larger than the discharger's bin-side diameter, and material flow can be sustained if the discharger is correctly selected. The main purpose of a bin discharger is to draw the bulk solids across the whole area of the bin outlet, to make the opening fully effective. As long as the bin-side opening of the discharger is large enough

Jan 1, 1969

By J. Kitagawa

INTRGDUCTION The Paragsha concentrator is the largest of Cerro de Pasco Corporation's base metal beneficiation plants operating in Peru. At present, this plant is treating an average of [ ]

Jan 1, 1970

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

Beverley S. Randolph, Frostburg, Md. (communication to the Secretary): It has always appeared to me that each coalseam has its peculiar character or habit, due to the conditions of its formation, by virtue of which it is either persistent or variable in its section over extended areas. One seam will hold its thickness, chemical character, number and position of partings, beds of slate, etc., over a large area, while another will be found to vary in some of these characteristics every few feet. As the position of the outcrop is an accident of the topography, depending on folding and erosion which have taken place since the bed was formed, no one opening in the outcrop, or, in fact, anywhere else, can supply reliable evidence as to the general character of the seam. To determine the character of an untried seam, a number of sections are necessary from widely separated points, in order to show such variations as may exist. Should material variations be developed, more numerous sections are necessary, in

Jan 1, 1901

By Kenneth K. Humphreys, F. R. Zachar, A. G. Gilbert

INTRODUCTION by F. R. ZACHAR and A. G. GILBERT Coal producers are not only faced with the problems of mining coal, but must also decide to what extent they can invest capital and what operating and maintenance expense they can afford, after mining, to market their product in sufficient volume and at a reasonable profit. Regardless of whether the operator is contemplating a new operation or merely considering expanding present facilities, market requirements, ability to make a product meeting requirements, probable costs and possible future changes in raw coal or finished product must be considered. In addition, such items as flow sheet, structural designs, storage facilities, etc, must be examined individually and collectively. In estimating preparation costs to meet predetermined market specifications, the operator must calculate the economics of present preparation practices to anticipate the increase to total production which results when the quality of the finished product is increased. The consumers of coal are continually seeking to obtain the best and most adaptable product for their money. Regardless of whether coal is used for coking, industrial requirements, electric power generation, domestic fuel or for other purposes, it will be scrutinized from such standpoints as delivered cost, suitability for utilization in certain equipment, ease of ash disposal, adaptability to material handling system plans and its potential for generating dust problems. Utilities, due to large capacity volume requirements, are generally in a position to select coal that will result in the lowest over-all cost per million Btu. Freight costs, paid by the utility, are important and are given utmost consideration when a coal is under consideration. Steel companies, whether producing or purchasing coking coal, are continually seeking coal that will result in lowering the cost of pig iron production. Since it is usually necessary to clean to lower specific gravities, say 1.40, to turn out a product meeting metallurgical requirements, it follows that a high ash "middling" product is created. These low quality middlings do not command a good price. Therefore, unless the metallurgical coal can command sufficient realization to carry or subsidize the middlings, the operator may be ahead economically to prepare steam coal at a higher specific gravity. While the "unit-train" rate reductions have been helpful to the economy of the coal industry, the establishment of these rates has made mandatory the installation of storage and rapid car loading facilities at mines and plants shipping utility coal (see Chapter 15). A study of the economics

Jan 1, 1968

By Henry Howland

INTRODUCTION DURING the last decade no topic has created more interest or received more thought among blast-furnace men than colic. One reason for this is, undoubtedly, the remarkable increase in the use of byproduct coke. Formerly our coke was made at a distance from the furnaces and by a distinct organization. There was little cooperation or development possible under these conditions. Today the situation is greatly changed. Much of our coke is made by the organization operating the furnaces and the coke oven is operated with the primary object of obtaining the best results in the blast furnace. The effect of changing the method of coke manufacture, even in some minor detail, is often felt almost immediately at the blast furnace. There naturally results one of the most valuable assets of the byproduct coke oven, -i.e., the possibility of increased blast-furnace efficiency clue to close observance and correct operation of the ovens. The results are evident, but it often is difficult correctly to account for them. In attacking the solution of a problem of as much importance as why one coke is better than another, there are facts which should be kept clearly in mind The author hopes, in this paper, to bring out some points relative to the use of carbon in the blast furnace which will be of value in solving this question.

Jan 3, 1916

Lake Superior Meeting . PAGE Gathmann, Emil.-Casting and Molding Steel Ingots. Discussed by J. W. Richards.. 2 McCaffery, R. S.-The Acid Bessemer Process. Discussed by Bradley Stoughton, J. W. Richards 3 Elliott, S. R.-Athens System of Mining. Discussed by F. W. Sperr, Lucien Eaton 4 Mercer, H. T. and Paulson, A. C.-Handling and Treatment of Rock-drill Steel at Copper Range Mines. Discussed by Harrison Souder, H. T. Mercer, W. H. Schacht, C. M. Haight 5 Hayden, J. E. and Eaton, Lucien.-Building Reinforced-concrete Shaft Houses. Discussed by William Kelly, T. L. Condron, Lucien Eaton 7 Eaton, Lucien.-Mechanical Ventilation at Lake Mine. Discussed by C. A. Mitke 8 Schacht, W. H.-Steam Regenerators Reduce Coal Consumption. Discussed by 0. P. Hood, W. H. Schacht ? 9 Linton, Robert.-Standardizing at North Butte Mining Co. Discussed by Grant H. Tod, C. A. Mitke 10 Smith, H. DeWitt and Sirdevan, W. H.-Mining Methods and Costs at United Verde Mine. Discussed by C. A. Mitke 12 Davy, Myron A.-Reflecting Microscope for the Mining Engineer. Discussed by C. P. Berkey, W. A. Rukeyser 14 , Norden, J. A. and Willson, A. R.-Hoisting Equipment at Utah-Apex Mining Co. Discussed by E. M. Norris 17 Aldrich, H. R.-The Dip Needle in Stratigraphy. Discussed by H. R. Aldrich, W. 0. Hotchkiss, Carl Zapffe, E. A. Kronquist 18

Jan 1, 1921

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation.

Jan 9, 1953

By Frank R. Van Horn

In the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chisml in 1887, and the other by Malcolmson² in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. 11. Geographical Location of the District. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district.

Jan 1, 1913

By J. Price Wetherill

The coal-seams that are worked vary from 3 1/2 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the general system pursued is to reach with a permanent outlet such a point in the seam as will

By Benj. F. Tillson

To most mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount of drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be SO handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau of Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 1, 1922

By R. T. Keyes, R. B. Clay, L. L. Udy, V. O. Cook, M. A. Cook

Based on compressibility and stress wave velocity in rock, initial explosive loading conditions, the thermochemistry of the explosive and reasonable description of the pressure-distance relations behind the shock front, the distribution of energy between the products of detonation and the burden are estimated as a function of time for various loading conditions. These include 'powder factor', loading density A (fraction of borehole occupied by explosive), and the explosive itself. Factors responsible for rock fragmentation are discussed in terms of: 1) 'release wave fracturing', 2) 'shear wave fracturing', and 3) 'release of loading fracturing' or 'rock bursting'. Release wave fracturing appears to occur only in the immediate vicinity of free faces, and shear wave fracturing only adjacent to the borehole under normal blasting conditions. Rock bursting is thus considered to be the most important means of rock fracturing in blasting. Means for maximizing it are considered. The most important factors to consider include maximum available energy A, explosive density p1, loading density A and 'powder factor'. Maximum efficiency is attained in general by maximizing the A . p1 product. This is achieved by using high density explosives at a loading density of unity (A = 1.0). Ways for achieving this condition are discussed. The bulk-handled aluminized slurry blasting agents have the desired properties for achieving optimum conditions for high blasting efficiency based on the theory outlined herein. Factors considered most important in the blasting of rock are: 1) The maximum available energy A, determined by the heat of explosion Q and the mechanical efficiency ?, a factor intimately associated with the mode of application (A = Q at highest gas concentrations). 2) The 'borehole pressure', pb, or the maximum pressure developed in the borehole after passage of the detonation wave and before the burden has had time to move or become compressed appreciably. (Owing to the short duration of the detonation wave at any particular point in the borehole, the fact that the explosive may not always fill the borehole completely and the further fact that the burden may not actually see the detonation pressure, the borehole pressure is considered more significant than the detonation pressure p2 as a performance factor in borehole blasting.) The borehole pressure is determined by the explosion or adiabatic pressure, p3 , and the loading density, A, or the fraction of the borehole filled by explosive. 3) The physical conditions important in the application of the explosive are: a) The 'powder factor,' (We/Wr), or the ratio of the wt of the explosive to that of the rock being blasted expressed as lb per ton or more generally in lb/cu yd. b) The bulk density, p1 ?. c) The 'burden' or 'line of least resistance,' the spacing between boreholes, the geometry of the borehole pattern and sequence of firing. d) The physical and chemical properties of the rock, most significant of which are possible heterogeneties, such as faulting, prefracture, and greater than micro-scale chemical heterogeneities. (This factor is not considered here but deserves a great deal of careful consideration.) All of these factors need to be carefully considered in the most economical engineering of a blast. Here is considered firstly an outline of the present status of dynamic rock mechanics, particularly as it pertains to blasting. The factors pertaining to the most efficient application of blasting agents are also considered, followed by a discussion of methods of application to achieve optimum explosives performance. ROCK MECHANICS Dynamic rock mechanics is currently a rapidly developing science contributing greatly to a better understanding and consequently the more effective application of explosives in blasting of rock.1-22 Basic to the development of the science of dynamic rock mechanics were the advances of Goransen23 and the Los Alamos and NOL groups24-28 concerning rock and stress wave phenomena and the transmission and reflection characteristics of stress waves at interfaces between different media. Basing considerations on this new knowledge as well as new experimental methods of study (ultra-high speed streak and framing cameras and electronic timers) the theory of fracture and failure of solids under impulsive loading by stress waves developed rapidly.14,16,27-29 Also the

Jan 1, 1967

By Benj. N. Webber

There is a broad analogy between super gene nickel deposits and super gene copper deposits of the porphyry type. Some of the nomenclature of supergene copper may he applied to super gene nickel deposits. The obvious connection between lateritization and supergene nickel concentration requires some clarification of the nomenclature of laterite of ultrabasic rock parentage. Lateritization is a progressive process and the transition products of the laterite profile are a key to the process of nickel concentration since the profile grades from unaltered peridotite to the highly ferruginous ultimate laterite capping. This profile is formed under highly restricted geographic and geologic conditions. Faulting contributes to the formation and localization of the higher grade commercial segregations of nickel. That there may be auxiliary sources of nickel other than olivine is suggested. The volume of peridotite necessary to produce a unit of laterite at any point in a complete profile is calculated on the basis of the chromite content. The lixiviation, transportation, and precipitation of the elements involved is considered and the source of the reagents and chemical mechanisms are suggested. The role of sodium chloride is considered important. The progressive changes in the lateritic profile have an effect on the general process since lateritization takes place in overlapping environmental phases. The mineralogy of laterite and the redistribution of elements is illustrated by compositional curves derived from a completely mature laterite. Nickel scanvenged by iron oxides tends to be redissolved and moves downward to the zone of transitional magnesium silicates where it is reprecipitated. The geometry of the nickel enrichment zone is simple in general, but complicated in detail. Elongated pods of a greater concentration of nickel are indicated to be a reflection of faulting. Lateritization and concentration of nickel may be arrested at any stage and be modified by several factors.

Jan 1, 1973

By James M. Barker

Jan 1, 1985

By Rex B. McLellan

Studies of the eyuilibrzum between ferrite and austenite with gas mixtures (CO + CO2 and H2 + CHe) have been used as a means of deducing the energy and vibrational entropy of carbon atoms in dilute interstitial Fe-C solutions. A simple model for dilute interstitial solutions is given which enables a solubility equation for the equilibrium between the gas mixtures and the solid to be deduced. This solubility equation is used to estimate the partial In this work measurements of the equilibrium between dilute solid solutions of carbon in iron and gaseous mixtures of CO2 + CO and CH4 + Hp have been analyzed using theoretical solubility equations deduced from a knowledge of the thermodynamic parameters of the gas mixtures and an appropriate model for the solid solution. The solubility equations are deduced by equating the chemical potential of carbon atoms in the gas thermodynamic functions of dilute Fe-C solutions from the measured equilibrium between the solid and the gas mixtures. It is shown that the vibra-tional entropy of a carbon atom in a and y iron is smaller than the corresponding entropy 01. a nitrogen atom in solid solution inferrite or austenite and that there is little difference between the vibrational entropies of both nitrogen and carbon atoms in ferrite and austenite. and solid phases. The chemical potential of carbon in the gas is found from a simple statistical mechanical analysis of the gas mixtures utilizing spec-troscopic data while that for carbon in the interstitial solution is found from a model in which the carbon atoms act as bound oscillators distributed in a random fashion in the solution. The solid solution is dilute enough to enable solute-solute interactions to be ignored. Thus the configurational entropy of the solution is ideal but the mixing entropy contains additional excess terms due mainly to the vibrational changes occurring on solution formation. The partial excess entropies (and the partial energies) do

Jan 1, 1965