Search Documents

By R. L. Slobod, C. Gatlin

This .study defines the basic mechanism of the mis-cible displacerrzent of oil and writer from porous Medici by various water-driven alcohol .slugs. Three distinct alcohol slug processes were .studied. Considerable data concerning the quanity of alcohol required for oil recovery were also obtained. All data were obtained in a 1-in. diameter, 100-ft long, unconsolidated core. The porosity of this system was 35 per cent. and the permeability was approxitrlately 4 darcies. Total core pore volume wax 5,716 cc. All displacements were conducted at a constant injection rate of 5 to 6 cc//min, which corresponds to a frontal advance of 5 ro 6 ft/hr. The first portion of this paper is concerned with 111 use of one alcohol—isopropyl—a\. the slug material. Isopropyl alcohol (IPA) is completely miscible with both oil rind water; however, miscibility of the threc-component systems, oil-water-IPA, requires a relutively. high concentration of IPA. Hence, the displocement is not of the misoible type unless the IPA concentration is maintained above some critical value. A slug of IPA equal to only 13.5 per cent of the pore volume was jound to be sufficient to obtain complete recover?, of residua1 naphtha. In later studies two distinct process variations were developed. The firsr of these utilized methyl alcohol (MA) and IPA as slug materials. It was shown that methyl alcohol may he substituted for IPA at the front and rear of the slug with no loss of oil recovery. A .slug of 4 per cent MA-4 per cent IPA-4 per cent MA was sufficient for complere oil recovery. Because MA is considerably cheaper than IPA, this represents an important step toward economic application. A .second process variation used normal butyl alcohol (nBA) and MA as the composite slug, the nBA segnzent being injected first. This technique requires the smallest total slug size (approximately 10 per cent) of all processes studied. The high cost of nBA, however, precludes commercial application. It is possible that this basic process, subject to changes of alcohol type, may lead to a commrercicil process. INTRODUCTION Within the last 10 years, considerable study has been devoted to the general mechanics of miscible phase dis- placements in porous media. These studies have. in general, dealt with two-component displacernent. All reported field trials to date have been modified gas drives of one type or another. These utilize either lean gas at high pressure, rich gas at lower pressure or an LPG slug. The irreducible water content of the reservoir remains immobile during these processes. Although these techniques hold great promise. certain drawbacks do exist. Poor areal sweep efficiency, inherent in any displacement having a highly unfavorable mobility ratio, is one disadvantage. Furthermore, the miscibility of all processes which use gas is dependent on pressure. These pressure limitations may prohibit application to shallow reservoirs. There are also many areas where large quantities of LPG and natural gas are not readily available. These factors emphasize the need for improved techniques. The alcohol slug process is also a miscible-phase displacement process. It differs from the previously mentioned two-component techniques, however, in that both the reservoir oil and water are displaced by the slug. This behavior is a consequence of the miscibility of certain oil-water-alcohol systems. In the simplest case, a relatively small volume (slug) of an alcohol (such as isopropyl) is injected into the system. Water is then used to drive the slug through the medium. Thus. three components—-alcohol. oil and connate water-—exist at the front side of the slug. Miscibility is obtained at some alcohol concentration, this being dependent on the solubility of the particular system. Miscibility is maintained within the slug until the alcohol concentration falls below that value required to maintain miscibility. When miscibility is lost, the process reverts to a water flood. Certain inherent benefits of this technique are apparent. High pressures are not necessary to obtain miscibility in these liquid systems. Furthermore, water is a more desirable driving agent than gas because of the improved mobility ratio and the attendant improvement in areal sweep efficiency. The main disadvantage is, of course, the relatively high cost of alcohols. The use of an alcohol slug to recover reservoir oil is not a new idea." ' However, this process has received only limited study, presumably due to the lack of industrial interest caused by the seemingly prohibitive cost of alcohols. The main purpose of this study was to investigate the mechanism of the displacement of oil and water by various alcohol slugs and to develop process modifications aimed toward possible commercial application.

By F. W. Maclennan

ORE production from the property of the Miami Copper Co. began early in 1911. Until 1925 this ore came from the so-called high-grade orebodies, which contained a little over 2 per cent. copper. This ore was mined by the following methods. 1. Top slicing after mining the peaks by square setting, which produced 4,524,347 tons, including ore from square setting. 2. Shrinkage stoping with sublevel caving of the pillars, which produced 2,230,577 tons. 3. Undercut caving with hand tramming, which, produced 15,427,672 tons. Estimating December tonnage, the total ore mined to the end of 1929 will amount to slightly more than 43,000,000 tons. The first method was described by E. G. Deane1 and the second by D. B. Scott,1 and the third, together with a general, description of the mine, by J. H. Hensley, Jr.1 The geology of the district has been worked out by. Dr. F. L. Ransome.2

Jan 1, 1930

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By D. A. Elgillani, M. C. Fuerstenau

With either sulfonate or oleate as collector, quartz responds to flotation with moderate additions of calcium only at moderately high pH, where some portion of the activator has hydrolyzed to caOH+ . Calculations of the concentrations of various ionic and precipitated species of calcium and collectors suggest that the products of [(CaOH+) (RSO3)] and [(CaOH+)(01-)] determine whether flotation is obtained under specific conditions. Ion products on the order of 10-12 were calculated for both the sulfonate and oleate systems. The activating effect of calcium ion in nonmetallic flotation systems is of considerable interest because of the normal presence of calcium in natural water. As a result, this phenomenon has received quite some attention in the past. Kraeber and Boppel1 showed that quartz could be activated by calcium above pH 10 with sulfonate as collector. The feasibility of selectively separating quartz from hematite with calcium activation at relatively high pH was demonstrated by Clemmer, Clemmons, Rampacek, Williams, and stacy.2 Cooke and Digre3 showed with a bubble pick-up method that the minimum quantity of calcium ion required as activator for complete pick-up of particles occurs at pH 11.5 for an addition of 20 mg per liter sodium oleate. They also showed that larger additions of calcium (10-fold increase per unit decrease of pH) must be added for complete bubble pick-up as the pH is reduced. Schuhmann and Prakash,4 using a vacuum flotation technique, found that quartz could be floated with moderate additions of calcium chloride and oleic acid at neutral pH, providing the metal ion was present in stoichiometric excess over the quantity needed to form the normal soap with oleic acid. They also reported that calcium will function as an activator only in basic media. More recently, Eigeles and volova5 have shown that essentially complete flotation of quartz is obtained with 6 x 10-4 mole per liter calcium chloride and 1.7 x 10-5 mole per liter sodium oleate at pH 11.6. while no flotation is obtained at about pH 10.9 and below. The importance of adsorption of activator and collector at the air-liquid interface is also demonstrated in these systems. The important role that metal ion hydrolysis assumes in quartz activation systems was also demonstrated recently.6-8 A detailed investigation of metal activation in sulfonate flotation of quartz was undertaken in one system7 and yielded a number of interesting and important observations. Quantification of the data of this system7 to the extent desired was not possible, though, because certain species could neither be ignored nor accounted for accurately. These difficulties can be circumvented when calcium is involved as activator. This detailed analysis was undertaken to obtain a more quantitative explanation of calcium and metal ion activation in quartz flotation. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate9 mol wt 450, and pure potassium oleate were used as collectors. All other reagents used were reagent grade in quality, i.e., n-amyl alcohol as frother, KOH for pH adjustment, and calcium chloride. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. The experimental equipment and procedure were the same as that described previously.6,10 EXPERIMENTAL RESULTS As the presence of precipitates was noted in all of the systems to which ca++ and collector were added, experiments were undertaken to determine the solubility products of calcium sulfonate and calcium oleate using a nephelometer. With this technique, collector is titrated into a known solution, which in this case was 5 x 10-5 mole per liter CaCl2 at pH 5.5. Upon precipitation of the calcium-col lector salt, e.g., calcium oleate, light is scattered and detected

Jan 1, 1967

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By W. J. Joslin

The frontal-advance equation can determine how the fluid withdrawal rate and subsurface operating pressure influence oil recovery from pressure-maintained reservoirs having characteristics favorable for efficient vertical segregation. For effective vertical segregation in formations having low dip angles, the requirements are: thick, massive sands, low viscosity oil and high vertical permeability with few discontinuous shale members. This approach has been successfully applied to the LL-370, which is a massive Eocene sandstone reservoir containing crude with an average gravity of 26" APT, a dip of only 3" and vertical permeability of ½ darcy. The average gas cap saturation was calculated for various rates of vertical gas-oil contact movement corresponding to a wide range of reservoir producing rates. This method also evaluated the effect of different pressure maintenance levels on oil recovery. Applicability of this procedure for calculating the present oil saturation in the LL-370 gas cap has been substantiated from field performance, where the oil saturation was computed by comparing oil recovery with the gas cap volume vacated. INTRODUCTION During the natural depletion history of the LL-370 reservoir, located in Lake Maracaibo, Venezuela, excellent vertical segregation resulted in the formation of a thin gas zone over a substantial portion of the oil-productive area. Subsequently, gas injection forced this thin gas-saturated zone slowly downward, reducing the oil saturation in the gas cap to a low value. The oil recovery has been raised considerably above earlier predictions where vertical segregation effects were under-estimated. In order to determine the maximum efficient producing rate and optimum operating pressure for this reservoir, a vertical gas frontal-advance analysis has been made through application of the fractional flow equation. LL-370 RESERVOIR CHARACTERISTICS The reservoir consists of a truncated monocline of massive. highly-permeable Eocene sandstone, called the B-b formation, covering an area of more than 13,500 acres. The original oil in place was 2.17 billion STB. Internal non-sealing faults subdivide the structure into four blocks called the B-6-x.6, 10, 11 and 13, which are effectively bounded by major faulting on the flanks, an unconformity updip to the west, and an immobile aquifer to the southeast. The producing formation occurs at an average depth of 5,250 ft subsea and has a closure of more than 1,500 ft. A typical producing section has a net oil sand thickness of 170 ft. Scattered throughout the section are a few randomly-positioned shale lenses which increase in thickness and areal extent downdip. The reservoir rock and fluid properties vary with depth. The permeability and produced oil gravity are 1600 md and 28" API at the top, compared to 300 md and 18° API at the water-oil contact. The productivity of updip wells is, therefore, much higher than the reservoir average. The reservoir oil was originally saturated at the crest, grading to a slight degree of undersaturation at the water-oil contact. There was no original gas cap; and material balance and the field performance indicate no water influx. Except for the northern B-6-x.6 block, the fluid and rock properties have already been published.' Average LL-370 reservoir properties are shown in Table 1. RESERVOIR PERFORMANCE UNDER NATURAL DEPLETION Fig. 1 shows production performance from 1939 to date. Early development was gradual, with 30 wells pro-

Jan 1, 1965

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By Charles W. Carter, Alfred H. Bell

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Alfred H. Bell, Charles W. Carter

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By A. N. Diehl

IT is the object of this paper (1) to deal with the elements in blast-furnace gas from the standpoint of their importance, and the part they are to play in future consumption, and (2) to give detailed information about the construction and operation of a plant designed among the first in this country for washing gas on a large scale.

Jan 5, 1914

By R. E. Pollard

The National Bureau of Standards received, in August 1940, a number of samples of bridge wire taken from the cables of the General U. S. Grant suspension bridge over the Ohio River at Ports- mouth, Ohio. These cables were 7% in. in diameter under the wrapping and each was made up of 1458 ungalvanized wires of No. 8 gage in 3 parallel-wire strands. The choice of ungalvanized wire was based on the previous satisfactory performance of similar wires in other bridges over periods of 20 to 50 yr. of service(1).2 After about 12 yr. of service a number of breaks were discovered in the Portsmouth bridge cables, most of them at the anchor- age shoes, and they were replaced by cables made up of galvanized wire(2).

Jan 1, 1945

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By A. G. H. Andersen

A FEW years ago, while the writers worked on the constitution of ternary and quaternary alloys consisting mainly of iron, chromium and silicon1,2 some information on microstructures and hardness, not incor-porated in the published work, was obtained. It has not been possible to do any further work on the properties of the alloys. The information possessed is hereby presented for the interest it. may have in connection with the constitution of the alloys.

Jan 1, 1937

The following paper, submitted by the Russian petroleum authorities, was secured through the courtesy of G. V. Ackerman, Vice President of Amtorg Trading Corporation, and N. V. Vannikoff, Representative in the U.S.A. of the United Oil and Gas Industries of the U.S.S.R. It gives an excellent view of the Russian petroleum industry as seen through Russian eyes. Noteworthy is the tremendous area over which the Russians are searching for petroleum, for this paper refers to such far-flung areas as the Arctic Tamir Peninsula, Kamchatka and Sakhalin on the Pacific, Lake Baikal in Central Siberia, the great new discovery at Neftadag in the plains of West Turkestan, and the oil of the Ferghana oasis, where the derricks look out over to the mosques of Kokand. Of interest also is the new pipe line to supply the industrial centers of Ukraine grouped around the great hydroelectric plant built at Dneprotroy on the falls of the Dnieper. The technical achievements have been noteworthy and we must pause to consider the scope of the undertakings being carried forward. Russia is at the worst a good second to the United States in petroleum reserves and for a long time to come will be a most important factor in the petroleum markets of the world. Her story should be of interest to everyone in the industry. The First Five Year Plan The first Five Year Plan, covering the period 1928-29 to 1932, accomplished the task of transforming the Union of Soviet Socialist Republics from an agricultural, backward land into a powerful independent industrial country, with an advanced technological foundation of its own for finally achieving the social reconstruction of the entire national economy. Along with the gigantic forward 'strides in industry and transportation, radical changes took place in agriculture. The creation of more than 5000 great state farms and of more than 200,000 collective farms serviced by a widespread network of machine-tractor stations has brought the U.S.S.R. to the fore as the largest agricultural country in the world. Imports of tractors and other agricultural machinery in the initial years of the Five Year Plan and the intensive output of this equipment by the great plants of the U.S.S.R. in the latter years of the plan have brought about the mechanization of agriculture in the Soviet Union. This year 250,000 tractors and 30,000 combines will operate in the fields

Jan 1, 1934

By J. G. Koenigsberger

THE electrical specific resistance of rocks in the field is measured by sending a current through a medium of great volume, compared to the electrodes, whose resistivity should be measured. The whole resistance can be determined by the Wheatstone bridge and the specific resistance calculated by a well-known formula. The resistivity of some rocks in place in Germany and in Switzerland is given; first, of a rock near the surface, and especially near electrodes. Practical applications are made in the determination: (1) of the continuity of a conducting orebody; (2) of the surface area of an orebody; (3) in the detection of a water-bearing fault in a salt mine. Preliminary observations are described: (1) on the influence of the depth of ground-water table; (2) on the detection of gas under high pressure in coal seams. The observations in this paper of the electrical resistivity of rocks and soil in place are along the lines of the very interesting method and results of the Messrs. Gish, Rooney, Hotchkiss and Fisher.1,2 All the work described has been done since 1920.

Jan 1, 1928

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

By C. A. Hartnagel

The production of petroleum in New York state in 1942 amounted to 5,410,000 bbl. This represents an increase over each of the four preceding years, and, with the exception of 1937, is the largest production since the peak of over six million barrels in 1882, shortly after the discovery of oil in Allegany County. The oil industry in New York is virtually stabilized and there has been little or no exploration for new sources of supply in recent years. The boundaries of the present fields were established more than 30 years ago and since then no additional reserves have been found. Deep drilling for natural gas during the past 10 years both within and without the oil fields has failed to find oil in quantity below the present producing sands of Devonian age. Oil Since 1882, the New York fields have produced approximately 140 million barrels of oil. Of this amount, 65 million was produced up to the year 1919 by ordinary pumping methods; that is, without flooding by water or the use of other secondary-recovery methods. In the year 1919, when a law was passed making the use of water-flooding methods legal, the oil production, of the state amounted to only 851,000 bbl. In the 23 years since 1919, there have been produced in the state 75 million barrels, or 10 million more than in the previous 37 years, which included the period of flush production. Price.—On March 26, the price of crude oil was raised from $2.75 to $3.00 per barrel, hut this increase had little or no effect on the number of wells drilled. In the Allegany field, which accounts for three fourths of the state's oil production, 1259 wells were completed in 1942, 7 less than in 1941. The smaller number of wells drilled was not only due to the shortage of labor but also was caused by the fact that in water-flooding territory a definite program for drilling wells is followed, and the flush period of an oil well is not usually reached in time to profit by any given price increase. Daily Production.—All of the oil wells in New York state, some 21,000 in number, are small producers. The average daily oil production is 7/10 bbl. per well. Under good flooding conditions, a maximum production of 5 to 8 bbl, a day is reached about one year after the flood begins to act on the well. In 5 years the daily production usually is less than one barrel. Although most of the oil in New York is produced by flooding, an estimated 2500 old wells produce without flooding. Some of these produce as little as 1/20 bbl. a day and are pumped only at intervals. The small producing Wells are mostly on lands leased to the larger oil companies and later will be included in a flooding program. At present, they are pumped only because the owners of the land insist on the royalty. Government Aid Needed.—Because of its good lubricating qualities, New York oil is one of those for which there is an insistent and growing demand, but even at its present price of $3.00 per barrel, many of the operators are producing at a loss.

Jan 1, 1943

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-'. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.' Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.' In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970