Search Documents

By John B. Pearse

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway Managers determined on and have long applied a test of 1000 pounds falling 101 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails from our most reliable makers, break under a 6 foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 13 1/2 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent, of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. In England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariably

Jan 1, 1873

By W. F. Dietrich

This paper deals with the methods of mining the high-grade clays of California. The fact that the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines causes a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over 15 varieties are mined on a scale of 50 to 200 tons per day; and more than 50 varieties are mined at the rate of less than 50 tons per day. It is the aim of this paper to delimit, as far as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin1 and will not be considered here. Geographical and Geological Features of California Clay Deposits The greater part of the high-grade clays consumed by clay-working plants in California is mined from one of three producing areas in the state: (1) Lincoln, Placer County, on the eastern edge of the Sacramento valley, 30 miles northeast of Sacramento; (2) Ione, Amador County, in the foothills of the Sierra Nevada, 38 miles northeast of Stockton, and 12 miles west of Jackson, one of the important towns of the famous Mother Lode gold-mining district; and (3) Alberhill, Riverside County, 90 miles southeast of Los Angeles. Other districts of minor importance are near Cardiff and Carlsbad, San Diego County, and El Toro and San Juan Capistrano, Orange County. In addition, there are a number of isolated properties in various parts of the state.

Jan 1, 1928

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials; it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted.

Jan 3, 1918

By Harry Tufft

FOR many years the treatment of mine timbers with preservatives was confined to a few pioneer plants in the United States, and it is only in the past few years that the practice has grown appreciably. In a field study of the mine timber situation in Illinois, Pennsylvania, and further study of the situation in the country as a whole, I found that most mine operators did not keep records on mine timber that would afford the necessary data for determining the possible savings from preservative treatment. Some primary questions the mining engineer should be able to answer before making his decision on preservative treatment. for a particular mine are: (1) Quantity and cost of timber going into permanent workings annually; (2) quantity and cost of annual replacements due to decay; (3) life of untreated timber in different places; (4) desired life of timber. With the necessary facts in hand, he can then con-fidently select a method of treatment and preservative that is best suited to his needs. In former years when timber was cheap and an abundant supply could be had close at hand, as was the case in the majority of mining regions, the mine op-erator did not concern himself much except to see that enough was supplied to keep the workings safe. The cost figure for timber and labor, distributed to cost per ton of ore, was all the bookkeeping necessary. With present costs of timber, labor, and increasing length of haul to the mine, many operators are paying closer attention to timbering costs and studying them in. more detail. Some of the larger and more progressive opera-tions now keep detailed' figures that give information on all phases of their timber problems. However, at the majority of mines the data available do not permit such analysis. Checks as to where the different con-signments are placed, the date of setting, and the period

Jan 6, 1927

By H. R. Hanley, C. Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial developmerit in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained . British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive series of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1944

By Valentin R. Garfias, C. O. Isakson

The production of oil in Mexico during 1929 was approximately 45,000,000 bbl., or 5,000,000 bbl. less than in 1928. The production of the fields near Tampico showed a decline of over 10,000,000 bbl. for both the light and heavy crudes, which was partly offset by an increase of over 5,000,000 bbl. in the production of the fields in the Isthmus of Tehuantepec. During 1929 the retrenchment policy followed by practically all the companies was continued and no material improvement should be expected until the unsatisfactory conditions that brought about this situation are remedied. A new administration has just assumed control in Mexico; it should remain in power for 6 years, and the progress of the oil industry during that time will depend primarily on the policy pursued by the new government with respect to oil development. Development During 1929, there were drilled 214 wells as compared with 371 in 1928 and 583 in 1927. The percentage of producers in 1929 was 47.2 as against 34 per cent. in 1928. The new wells did not show water as quickly as in 1928, particularly in the Cacalilao field, where the greatest number of producers was brought in, their average initial daily production being 380 bbl. The flush daily production per well in the Southern fields was 1730 bbl., while the wells in the Isthmus of Tehuantepec came in with an average of 770 bbl. Development is summarized in Table 1. In the Southern fields 63 wells were drilled in 1929, of which 23 were producers, the best being drilled in Paso Real. This development tends to show that the southern extension of Dos Bocas-Alamo fault from Alamo to San Isidro terminates at San Isidro. The two wildcat wells completed in 1929, one in Magiscatzin and the other in Xicotencatl, were failures, and at the end of the year there were eight wildcat wells drilling and material was being hauled for two more.

Jan 1, 1930

By C. C. Hagenbuch

Machine loading of coal into mine cars is increasing rapidly. Particular reasons for its use frequently apply to certain localities, but in general, it is profitable to install mechanical coal-loading equipment: (I) when existing hand-loading contract rates prevent further cost reduction; (2) when the height of the coal bed requires that either top or bottom must be taken to place cars in rooms; (3) when labor shortage or limited house-plant capacity prevents the production of desired tonnage ; (4) when tonnage requirements are in excess of possible hand-loaded production from developed areas; (5) when working places are scattered and it is possible to concentrate production, and therefore supervision, by the installation of mechanical equipment; (6) when rapid development is essential. Having decided to install loading equipment, the problem then arises as to what type is best adapted for a particular mine or coal bed, the choice lying between mobile track equipment, pit-car loaders, scrapers, shaker conveyors, belt conveyors and drag conveyors. MajoR FactoRs Influencing Choice of Equipment In determining the type of equipment to be used, the following major factors must be studied: Grades.—Adverse grades, while permitting other types of loading equipment to work successfully, may prevent the success of a shaker conveyor installation. Thickness of Bed.—The thickness of coal governs the choice of equipment. A machine that requires 5 ft. of head room should not be selected for a 3-ft. bed where otherwise it would be unnecessary either to brush top or to lift bottom. Nature of Pavement.—Soft or scaly bottoms are unsuitable for the use of any type of digging loader, shaker conveyors or scraper loaders. nigging loaders and scraper loaders scale the bottom, mixing it with the coal and causing preparation difficulties; shaker-conveyor drives frequently work themselves loose, destroying the conveyor alignment and creating maintenance problems. Nature of Roof.—With any type of loading machine, it is policy to obtain the maximum possible tonnage per move per set-up. This must

Jan 1, 1931

By R. W. Heins, N. Street

Recently Hiller1 reported results on the impairment of the strength of quartz glass rods through wetting, indicating that there was general agreement with the prediction of the Griffith formula in that for the liquids used the rods were weakest in water i.e. the liquid which probably had the greatest free energy of immersion. The Griffith equation predicts that the tensile stress necessary to propagate a crack of length c is where ? is the interfacial free energy, E Young's modulus. Since for a solid immersed in a liquid of surface tension ?L and contact angle 8 at the solid-liquid-gas contact, ?s - ?SL = ?L cos ? where ?s is the surface free energy of the solid. Hence comparison between ?L cos 0 and strength impairment should be possible. In a study of the usefulness of the Kuznetsov pendulum2 as a means of studying rock drillability we have determined the effects of various liquids on the pendulum hardness of Bavarian limestone. The pendulum used had diamond points (Burgess Vibro-graver), a period of 1.14 sec and a total on sample weight of 1191 g. The decline of the pendulum oscillations was recorded by a light beam on light sensitive paper carried on a kymograph. Rehbinder's expression relating hardness to amplitude attenuation as a function of time can be written In A = - (1/H) t + In Ao where A, A, = amplitude at time t and initial amplitude respectively, H = hardness parameter, and t = time. The line of best fit to the experimental points was determined using the IBM 7090 electronic computer, the computer also gave A, by extrapolation to zero time. The results for the various liquids tested are given in Table I and Fig. 1. The limestone surfaces were highly polished before testing and each reported hardness value represents the average of at least ten separate determinations of the pendulum decline curve. On each newly prepared surface the water value was again determined (also

Jan 1, 1964

By Martin F. Milligan

THIS short discussion of the effects of deoxidation on the mechanical properties of cast steels is intended to serve as general introduction to the subject of this afternoon's session. The subject is covered in detail in Mr. Carter's excellent paper. My material has been collected from the works of various investigators, several of whom are present today. For a definition of deoxidation, as applied to steel-furnace melting practice, we can best go to Briggs' book, "The Metallurgy of Steel Castings." Briggs says that deoxidation "includes all the phenomena in the final preparation of steel that would permit it to solidify free from gas cavities and from dissolved oxygen of all kinds." Various practices are used by welters to produce these end results.

Jan 1, 1947

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Advertising Manager for Machinery Manufacturing Company. Must have technical training. No. 94. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate in Mining, Chemistry and Metallurgy, Post-graduate, Royal School of Mines, Freiberg, Saxony, Germany and Columbia School of Mines. Aged 37, 14 years' experience in teaching mining metallurgy, chemistry and assaying. Available now. Willing to go anywhere. No. 278. Member, aged 33, mining engineer, 88 years' experience, desires position as mine safety and efficiency engineer with coal company. Best of references on request. No. 290.

Jan 5, 1916

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be done by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will be a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts.

Jan 1, 1944

By A. W. McReynolds

E. OROWAN*—I observed the phenomenon of jerky yielding many years ago with zinc25 and cadmium single crystals. A significant point was that the jerks occurred not only when the stress was raised but also (sometimes, after a pause of many minutes during which no trace of creep was observable) at constant stress. The phenomenon may be closely linked with the inertia of the testing machine and of the specimen, although the inertia alone cannot account for it. If, during the test, the resistance of the material to plastic deformation suddenly diminishes while the applied force remains constant, a sudden deformation follows until the yield stress has risen, by strain hardening, to the level of the applied stress (= the value of the previous "upper yield point."). When this is reached, the rate of deformation has attained a maximum value because, up to this moment, the applied force was higher than the plastic resistance of the specimen, and the difference was used for accelerating the moving parts of machine and specimen. The kinetic energy accumulated is now transformed into plastic work by further deformation; that is. the deformation overshoots the point at which the plastic resistance equals the applied static force. When the kinetic energy has been used up, therefore, we are left with a specimen the yield stress of which is higher than the applied stress, and no further deformation can occur (apart from a little creep) until either the applied stress has been raised to the new yield stress level, or the yield stress has fallen by thermal recovery to the level of the applied stress. While this occurs, a new upper yield point can develop, for example, by precipitation.26

Jan 1, 1950

By J. M. Sands

Describes important developments in, four counties, all of which brought in 40° oil. Indications are favorable for the future, although the daily production of the agate decreased 19,000 bbl. during the year 1923. THE state of Kansas had a daily average crude-oil production of about 87,000 bbl. at the beginning of the year. This showed a steady but consistent decline during the 12 months, so that the daily average production at the end of the year was slightly over 68,000 barrels. GREENWOOD COUNTY THE most active development in Kansas during the year was in Green-. wood County, in a line from near Sallyards in T 25-R 9 to east of Madison in T 22-R, 11. The main part of. this development has been in a succession of pools beginning at the south with the Polhamus pool in 34-24-9 and 3 and 4-25-9; Thrall pool in 28, 29, 32 and 33-23-10; Burkett pool in. 13, 23, 24 and 26-23-10; Seeley and Wick pool in 22, 27, 28, 32 and 33-22-11 and 5, 6, 7, and 8-23-11; Frohm pool in 11, 14 and 15-22-11; Madison pool in 31 and 32-21-12 and 6, 22, 12 and 1-22-11. Some of these pools, have two or more sands, locally called Bartlesville and Burgess Sands. They range in. depth from 1850 ft. near Madison to 2450 ft. near Sallyards, the general dip being to the west. The thickness of these sands runs from 20 to 100 ft., the initial production of the wells being 50 to 1000 bbl. of 40-gravity oil or better.

Jan 3, 1924

THE Fall Regional Meeting of the Institute, which has now for some years been held in cooperation with the Western Division of the American Mining Congress, will be held this year at Joplin, Mo., in the heart of the great Tri-State district. This year the Tri-State Zinc and Lead Ore Producers Association is joining in the meeting. The Society of Economic Geologists will also take part though not offering any papers. The district in which the meeting is held includes adjacent parts of Missouri, Kansas and Oklahoma. Out in the heart of a fertile prairie farming country, it is one of the major mining districts of the world. It produces normally approximately one-third of the zinc ore mined in the United States which is equivalent to nearly one-half the zinc since the concentrate has always been notable for the height of its grade. Even in the depressed business year 1930, the American Bureau of Metal Statistics credits the district with 434,460 tons of concentrates equal to 217,230 tons of zinc out of 1,503,095 and 576,630 respectively for the country as a whole. This was equal to about one-seventh of the world's output of zinc, more than that of any foreign country. In addition about 75,000 to 100,000 tons of lead is annually furnished by the same mines. Elsewhere we present a general description of the district prepared for this meeting by J. C. Heilman, a Lehigh graduate, who has spent the past eleven years there and has had charge of explorations for many of the companies.

Jan 1, 1931

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By R. A. Deju, R. B. Bhappu

The basic structural unit of all silicate minerals is a tetrahedron with a silicon atom at the center and four oxygen atoms at the corners. The oxygen-silicon distance is about 1.6 & and the oxygen-oxygen distance about 2.6 &. The different types of oxygen-silicon frameworks in the various silicates are based entirely on the combinations of the tetra-hedral oxygen-silicon groups through sharing of oxygen atoms. In recent years, infrared spectroscopy has permitted estimation of the ratio of the ionic character of the oxygen-silicon bond to be a few times that of the oxygen-carbon bond and the ratio of electro-negativity of the two bonds has also substantiated this finding. On this basis, it is generally accepted that the oxygen-silicon bond is the strongest one occurring in silicate minerals. As the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, there is increasing oxygen-to-metal bonding. Upon the fracturing of a silicate mineral crystal, the oxygen-metal bond, which is almost entirely ionic in character, should break more easily than the stronger oxygen-silicon bond, resulting in a greater number of unsatisfied negative forces on the surface. If, then the mineral is immersed in a liquid containing hydrogen ions, these negative forces should tend to be neutralized by hydrogen ions from solution, resulting in a change of the pH of the solution. An increase in the degree of adsorption of hydrogen ions is to be expected as the oxygen-silicon ratio in the crystal structure increases. This study attempted to correlate the oxygen-silicon ratio for various representative silicate minerals to the adsorption of hydrogen ions. Experiments to determine the effect of surface area on this adsorption and to investigate the effect of surface iron were also conducted. It is believed that such studies of the surface properties of silicate minerals will supply pertinent information about their behavior in froth flotation systems. EXPERIMENTAL PROCEDURE Ion Exchange: Carefully selected, hand-picked samples of the minerals investigated were dry-crushed in a ceramic ball mill and sieved to obtain a minus 100 plus 200-mesh sample. The sized samples were then run through the electro-magnetic separator to remove any iron-bearing particles. A 10-g sample of each mineral was placed in 100 ml of freshly deionized water previously adjusted to a pH of 3.50 with HCl. The beaker containing the sample and the water was placed under a bell jar from which the air was displaced at once by nitrogen gas from a tank. All experiments were carried out in a nitrogen atmosphere. The sample and solution were stirred gently but continuously during the entire experiment, the stirring speed being kept about the same for all runs. Changes in pH were followed with a Beckman Zeromatic pH meter and recorded on a

Jan 1, 1967

By W. M. Johns

The geological mapping of Lincoln and Flathead Counties was a five-year project undertaken by the Montana Bureau of Mines and Geology. This paper, written by the Project Geologist of the survey, is primarily concerned with the stratigraphy of the Belt rocks encountered in mapping. Lincoln and Flathead Counties of northwestern Montana are underlain by sedimentary rocks of the Belt Series of Precambrian age. In only a very small part of the area, near Libby and Troy, have economic mineral deposits been worked with any success. Most of the area has been inadequately mapped as to geology. The region is crossed by the Great Northern Railway and served by the Pacific Power and Light Co.; officials of these two companies believed that with better geologic maps, prospecting might be stimulated and lead to the discovery of mineral resources that would contribute to new economic development within the area. A cooperative mapping agreement was proposed jointly by the two companies to the Montana Bureau of Mines and Geology in May 1958, and thus was born the Kootenai-Flathead five-year project. The dual objectives of this project are: 1) the possible location of mineral deposits of economic value, and 2) the ''stimulation of prospecting exploration" by others. This was to be achieved by geologic mapping of some 6800 sq miles and by establishing a field office in Kalispell where prospectors could come to have their rocks and minerals identified and receive geological advice on their problems. This writer has finished four field seasons as Project Geologist and thus became familiar with the Belt section in the Libby, Yaak River, Ural, Thompson Lakes, Pleasant Valley, and Stryker quadrangles (see Fig. 1). Progress on the project is given in annual reports issued by the Bureau.* This *Montana Bureau of Mines and Geology, Bulletins 12 (1959), 17 (1960), and 23 (1961). paper is concerned essentially with the stratigraphy of the Belt rocks so far encountered in mapping. PREVIOUS WORK IN THE AREA Willis28 made the first study of the stratigraphy and structure in the Lewis and Livingston Ranges of Glacier Park just east of the project area. In 1904, Daly made a study of the Belt rocks of the 49th parallel, using the names from bottom up, Creston, Kitchener, Moyie, and Gateway, for rocks ranging in age from that of Prichard to that of basal Missoula group. Walcott26 studied the Belt rocks exposed in the Mission Range (see Fig. 1) and other areas to the south of the area under discussion. Calkins and McDonald made a reconnaissance of northern Idaho and northwestern Montana in 1905. Calkins was the first to use Walcott's term 'Ravalli' as a group name for the strata equivalent to the Burke, Revett, and St. Regis formations (see Table I). Clapp worked on the Belt of western Montana (including Lincoln and Flathead Counties) throughout his lifetime. The Fentons9 studied the Belt of Glacier Park and

Jan 1, 1962

By L. E. Young

LOADING machines may be classified in several ways: (1) Machines which cut or break down and load .the coal; (2) machines which simply load the coal; (3) devices which load and transport the coal; (4) de-vices which elevate; (5) devices which transport the coal after it has been shoveled onto the device. There are many types of mechanical loading devices, Bull. 17, Coal Mining Investigations, under the auspices of Carnegie Institute' of Technology, U. S. Bureau of Mines, and the Advisory Board, listing 31 exclusive. of -the large shovels used in thick coal seams. Mechanical loading of coal is not in its infancy; I think some of the early patents go back to 1890. One large coal company, properly called the early leader in this field of mechani-zation, has about 26 large machines at work. This company spent about thirty years in developing a ma-chine, and at the present time is loading approximately two million tons of coal a year in its mines. The chair-man directed a question at the previous speaker; inquir-ing if real progress was being made in mechanical load-ing. The experience of the company just referred to is in itself an adequate answer. A review of a list of mines using mechanical loading devices shows that there are 28 mines which we may say are 100 per cent mechanical. There are four more mines which have been 100 per cent mechanical, but which are idle at this time on account of labor condi-tions. There are at least 25 more at which the tonnage is more than 50 per cent mechanical. In speaking of a 100 per cent mine I do not mean that every pit car of coal is loaded by machine, because when complete, re-covery of the coal is attempted it is not practical to load all the coal at, the break line. In order to load the last 5 to 10 per cent of coal with a minimum of gob material and in order to keep the. working places along the break line timbered in a safe manner it is generally desirable to use a few hand loaders. At a certain mine operat-ing on the block system 90 percent of the coal is being loaded by what is properly a mechanical loading: device, and about 10 per cent -is being loaded by hand. This 10 percent is right off the break line, out of what might be called, the screen pillar. The mines referred to are scattered over the country, . in seven different' States, and the equipment used is produced by ten different machinery companies. As to size, these mines vary from small mines of 500 tons mining capacity-up. In one instance a company with one loading machine is producing an, average of 450 tons per day. One of the large mines that is idle pro-duced at the. rate of 4300 tons per day, of which 97 per cent was actually loaded by machinery.

Jan 8, 1928

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949