Search Documents

By Arthur West

IT is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic. plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 tons capacity each. In this, as in all the other stations described in this paper, each furnace is blown by-two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines.

Jan 6, 1915

By R. K. Hopkins

Fox a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By H. S. Price, R. L. Reed, J. E. Warren

The behavior of the reverse-combustion process in a linear adiabatic system is theoretically investigated by means of an idealized physical model. T his model is described by a pair of non-linear equations involving heat and mass transfer which are coupled by a concentration-dependent reaction-rate function of the Ar-rhenius type. The differential equations governing the quasi steady-state temperature and concentration distributions are approximately solved by using either physical or mathematical simplifications. It is shown that the reverse -combustion process can be mechanistically described by simple physical models whose behavior equations can be solved formally. It is further demonstrated that the derived reverse-combustion equations can be solved numerically within the error limits for the experimental data. The theoretically predicted peak temperature-flux-velocity relationship exhibits reasonable agreement with experimental data obtained from Athabasca tar sand. The principal contribution of this work lies in its usefulness as a starting point for developing a more comprehensive theory. A description of the vaporization-coking process must be obtained; then, the theory must be extended to three dimensions to include geometrical effects and heat losses. INTRODUCTION In another paper,'" he physical processes visualized as occurring during reverse combustion have been described. In this paper, the extent to which an elementary theory can account for experimental observations is determined. Theoretical results that can be used to estimate some of the behavior characteristics of importance to this process are also presented. Since it is not possible to include all the features of the combustion mechanism of which we are currently aware, the mathematical formulation refers to the highly idealized system developed herein. This simplified physical model is based on the simultaneous transfer of mass and heat accompanied by a chemical reaction: it is described mathematically by a pair of coupled, nonlinear differential equations. Similar sets of equations have been studied extensively in the field of flame propagation; an excellent review of these investigations has been published by Evans.1 FORMULATION OF THE PROBLEM It will be recalled that the experiments are performed with a thin-walled cylindrical tube that is uniformly packed with sand and oil. The system is maintained substantially adiabatic by means of heat supplied externally in such a way that the radial temperature gradient in any plane normal to the axis of the tube approaches zero. Initially, the tube is at ambient temperature, except at one end where it is rapidly heated to a predetermined temperature. When the prescribed temperature is achieved, air is caused to flow into the cold end of the tube. As the oxygen in the air stream contacts the hot oil, a localized exothermic reaction takes place. The generated heat is conducted and convected away from the reaction zone so that definite temperature and concentration profiles are rapidly established and move uniformly in a direction opposite to that of the air flow (Fig. 1). As a consequence of this mode of oxidation, all of the oxygen in the air is consumed; then, the remaining nitrogen and the gaseous combustion products sweep out all vaporized hydrocarbons and leave an immobile hydrocarbon-coke on the sand.

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By C. van Dijk

In Sept., 1960, a steam-drive project was started in the solution-gas drive area of the Schoonebeek field. A part(ern of three five-spots and one four-spot was selected covering an area of 65 acres. The pay in the project area has good lateral continuity and dips slightly to the northeut; it is about SO ft thick and permeability increases from 1,000 and at the bottom to approximately 10,000 md at the top. The oil originally in place was 12.6 X 10' bbl. The oil has an in situ viscosity of about 180 cp. At the start of the steam drive the cumulative primary production due to. solution-ga.7 drive amounted id 4 Percent of the oil originally in place. Reservoir pressure had dropped about 120 psi and no significant primary re-.serves remained. Some 11.3 million bbl of steam (all steam quantities are expressed in barrels of water vaporized) have been injected, resulting in production of an additional 4.1 X I0 9bl of oil, or 33 percent of the oil originally in place. This corresponds to a cumulative oil-stearn rario of 0.37 bbllbbl. It appears that the steam preferentially moves r updip while liquids are produced mainly from downdip wells observations indicate that tile steam flows through only the upper part of the formation. The lateral steam distribution in the pattern is satisfacrory since several prodriction wells hardly reacted and, hence, cori tributcd little to the oil production. Production performance and results from material balance calcutlations agree satisfactorily with the results of large-,scale laboratory experiments. On the basis of these experirmental results the .steam drive, together with a cold water follow-up. is expected to bring ultimate recovery to a value of crt leas: 50 percent of the oil originally in place. No serious production problems have been encountered. However, due to mechanical fuilure, two old prodriction wells and one injection well had to be replaced. An extension of the. steam drive in this area is under connstruction. Introduction The Schoonebeek oil field, discovered in 1943 and developed after World War 11, is situated in the eastern part of the Netherlands. The main oil reservoir in this field is the Valanginian sand. A completely sealing fault divides this reservoir into two areas (Fig. 1): the southwestern part of the sand body where primary production is ob- tained by means of a solution-gas drive, and the remain. der where edge-water drive is the production mechanism. In the greater part of the field the reservoir consists of a single, unconsolidated sand body. The net thickness ranges from 30 to 100 ft and the top is between 2,400 and 2,800 ft below sea level. Formation permeability varies from approximately 10,000 md at the top to values of the order of 1,000 md at the bottom, and porosity is about 30 percent. The reservoir contains a paraffinic oil of 25" API gravity with an in situ viscosity of 160 to 180 cp. Initial oil saturation was high (85 to 90 percent). The relatively large quantity of oil in place (more than 10' bbl), and the low ultimate primary recoveries expected from this field — approximately 15 percent stock-tank oil initially in place (STOIIP) for the water-drive area and 5 percent STOIIP for the solution-gas drive area — clearly indicate ample scope for secondary recovery. Because ies-ervoir and crude characteristics made this field suitable for thermal secondary recovery, a hot-water drive project was started in the water-drive area about 10 years ago. A few years later a steam drive and an in situ combustion project were started in the solution-gas drive area. This paper deals with the performance of the steam-drive project, which was started in Sept., 1960, and which is still in operation. Design of Steam-Drive Project, An experimental investigation of the steam-drive process carried out by schenk in 19561 indicated that under schoonebeek conditions steam injection could be an attractive secondary recovery method. the findings and encouraging results of a pilot test in the Mene Grande field in venezuela,i led to the design of a steam-drive project in the schoonebeek field, Pruject Site and Pattern In 1958 the reservoir pressure in the solution-gas drive area had decreased to about 120 psi, and oil production rates of wells in this area had dropped to 7 to 10 B/D. The cumulative primary production was about 4 percent STOIIP, leaving an oil saturation of approximately 85 percent. In view of the large amount of oil left behind in the reservoir, the solution-gas drive area was selected for the planned steam-drive project. The area in the vicinity of Well S1 3 (Fig. 2) was considered to be suitable since it is at least partly isolated from the rest of the field by faults and the sand is relatively thick (about 80 ft).

Jan 1, 1969

By EDBIUND U. NORTH

IN making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that. the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By Waldemar Lindgren

Jan 1, 1905

By AIME AIME

The following acts of the Directors are reported for the information of members:¬ At a meeting held November 3, 1905, Messrs. Henri Le Chatelier, of Paris, France, and Andrew Carnegie, of New York, N. Y., having been nominated by a large number of members, and recommended by unanimous vote of the Council, were unanimously elected Honorary Members, in recognition of their distinguished services to the arts and professions represented by the Institute. At a meeting held February 7, 1,906, Dr. James Douglas, of New York, N. Y., having been" nominated by a large number of leading members, and recommended by unammous vote of the Council, was unanimously elected an Honorary Member, in recognition of his distinguished services to the practice and the literature of mining and metallurgy, his zealous and loyal devotion to this Institute, his fraternal generosity towards professional colleagues, and his effective advocacy, by public utterance and private example, of the free communication of technical knowledge and experience. At the same meeting, By-Law IV., which now authorizes the Secretary to appoint an '1 Assistant Editor," was amended by substituting the words, " Assistant with the title of Editor." At the same meeting, the resignation of Mr. Theodore Dwight, as Assistant Secretary and Assistant Treasurer of the Institute, was presented and accepted, and the Secretary was instructed to express to Mr. Dwight the thanks of the Board for his loyal and efficient services, and its regret that he could not continue in that position. . [SECRETARY'S NOTE.-Mr. Dwight's resignation, dictated solely by the demands of private business, covers only his immediate management of this office. He is still a Director and Councilor, and a representative of the Institute in matters connected with the new Carnegie Building, etc.-R. W. R.] At the same meeting, the Secretary and the Treasurer reported respectively their appointment of Mr. Henry WT. B. Howard as Assistant Secretary and Assistant Treasurer, to fill

Mar 1, 1906

By I. R. Kramer

The stress associated with the high-dislocation layer at the surface of deformed aluminum crystals was measured by progressively polishing the specimen and determining the change in the initial flow stress when the specimen was reloaded. This surface stress increased linearly with strain in the Stage II and Stage III region. The depth to which the high-dislocation layer extends was found to be 0.0025 in. The influence of the surface layer on Stage I is discussed and it is shown that Stage I ends when, on the secondary slip system, the difference between the applied stress and the opposing stress due to the surface layer is equal to the critical resolved shear stress. In previous papers'-3 it was shown that the surface exerts a pronounced effect on the plastic-flow characteristics of metals. For fcc metals it was possible to increase the extent and decrease the slope of Stages I and II and decrease the work-hardening coefficient of Stage II by removing the surface of the specimen continuously during the deformation process.2,3 More recently,L it was shown that the activation energy for plastic deformation and the activated volume were also influenced by the surface. These changes were related to the existence of a high concentration of dislocations in the region near the surface of the deformed specimen and it was concluded' that the effective stress, T, acting on a dislocation was T = Ta-Ti-Ts [1] where 7, is the applied shear stress, Tj is the internal stress, and TS is the stress associated with the surface region containing the high concentration of dislocations. From Eq. [I] it is seen that the effective stress, 7, acting on a dislocation is a function of 7,. Therefore 7, becomes important in any description of the work-hardened state. In this paper the value of 7, as a function of strain and its variation with depth are reported for aluminum single crystals. In particular, it will be shown that the end of Stage I occurs when the net stress, 7, on the secondary slip system is equal to the critical resolved shear stress. To measure Ts, single crystals of aluminum were deformed in tension to various strains, whereupon the load was removed and a known amount of metal was removed by electrolytic polishing. The differ- ence between the final flow stress before the specimen was unloaded and the initial flow stress upon reloading is designated as ?Tp and is the decrease in the stress due to the removal of the surface layer in whole or in part. The value for Tp is taken equal to -Ts. EXPERIMENT PROCEDURE The details of the tensile apparatus, method of electrolytic polishing, and crystal preparation were the same as those used previously,1"3 The single crystals were 1/8 by 1/8 in. in cross section with a 3-in. gage length. The initial purity of the aluminum was 99.997 pet. The specimens were held in vacuo at temperatures 50°C below their melting points for 16 hr and furnace-cooled. Just prior to the application of the tensile stress the specimens were electrolytically polished to remove 0.004 in. from the thickness. This latter operation was conducted after the specimen was placed in the tensile apparatus. The tensile tests were conducted at a strain rate, i, of 10"5 sec-' and a temperature of 3°C. The aluminum crystals used for the determination of 7, are designated A1-3-12 and A1-116. The orientation of the various crystals used throughout the investigation is shown in Fig. 1. The ?Tp values for specimens A1-3-12 as a function of Ax were determined mainly at four strain levels, i.e., ? = 0.0217, 0.0381, 0.0593, and 0.075, where Ax is one half of the total reduction of the thickness after polishing and ? is the re-

Jan 1, 1965

By Carle Hayward

IN reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment he carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is -still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired tem-pressure throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treat-ment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-known tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels, which, after tempering for periods varying from 15 min to 2 hr., show no very great differences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 2, 1917

By Alexander L. Field

The Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity apparatus, furnace and other accessories mentioned in this paper have been described fully in s Bureau of Mines report.1 The Literature on Slag Viscosity The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method .or other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity., the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300" C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 1, 1917

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

Jan 1, 1899

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By R. W. Stormont, F. Wald

The phase diagram of the Pseudobinary section PbTe-Fe was determined. It was found to contain a monotectic and a eutectic reaction, the latter one taking place at 14 at. pct Fe and 875° * 5°C. The solid solubility of iron in PbTe was found to be 0.3 at. pct by electronmicroProbe analysis. No solubility of PbTe was detected in iron. Slight deviations from true pseudobinary behavior were found to occur in the range of - 5 to 10 at. pct Fe. In the course of a general investigation of reactions of various metals with lead and tin telluride,' the lead telluride-iron system was reinvestigated. It had been established much earlier than iron does not chemically react with lead telluride but forms a eutectic with a melting point of 879" The eutectic composition or other related information has never been reported, but for a number of years iron has been in general use for contacting of lead telluride and lead telluride alloys for thermoelectric applications. It seems therefore desirable to clarify the exact constitution of the system to furnish a base for the long-term evaluation of bonds made between lead telluride and iron either by pressure contacting or by brazing methods. I) EXPERIMENTAL METHODS Lead telluride-iron alloys were prepared in 10-g charges, using premelted lead telluride. This material was prepared from high-purity, semiconductor-grade lead and tellurium obtained from the American Smelting and Refining Co. and described as 99.999 pct pure. The iron used was "Armco" iron; the major impurities found here were 0.02 pct C, 0.018 pct Si, and 0.015 pct Cr. All remaining impurities were less than 0.01, the total of all impurities not exceeding 0.15 pct. Charges were prepared in closed quartz arnpoules which were evacuated and in some cases backfilled with high-purity argon to retard excessive lead telluride evaporation and deposition in slightly cooler parts of the ampoule. For high iron concentrations, this can lead to total separation of the constituents, since the vapor pressure and the sublimation rate of PbTe are quite high.4 Nevertheless, since the ampoules are closed, no change in overall composition was expected and the nominal composition of all alloys was assumed to be retained. X-ray diffraction analysis, thermal analysis, and microsections were used in the evaluation of the alloys. The nature of the system was such that X-ray diffraction was not particularly helpful. It merely served to establish that at all concentrations PbTe and a! iron were in equilibrium at room temperature. Thermal analysis was carried out by taking direct temperature vs time curves on a Sargent recorder where a width of 10 in. was kept as 1 or 0.5 mv by use of an automatic bucking voltage network. Quartz ampoules with minimized dead space, coated with boron nitride and fitted with a thermocouple reentrant, were used as containers for the charge. At high temperatures and over long periods of time, boron nitride reacts with iron. For the thermal analysis runs, however, this was not significant. More significant was the fact that the vapor pressure of PbTe at some of the meas -uring temperatures apparently exceeded I atrn quite considerably. This, in some cases, caused the slightly softened quartz tubes to blow out if great care was not taken to contain them and minimize time and temperatures used. As containers pure nickel tubes were used which also served to avoid temperature gradients in the quartz ampoule. Nevertheless, the experimental difficulties at high temperatures were severe and the monotectic temperature could therefore not be determined accurately. In general, the accuracy reached by the thermal analysis setup in this case is *4"C as determined with gold, silver, and tin, under the conditions of analysis here. Inherently, the apparatus is capable of reaching accuracies better than i 1°C. Also, difficulties were encountered in microsection-ing. They were related to polishing, since it is rather difficult to avoid pulling the iron out of the weak and brittle lead telluride matrix. It proved best to follow a procedure where, after grinding to 600 grit on carborundum paper, a polish with 6 p diamond was used on nylon cloth. Finally, #3 "Buehler" alumina and an automatic polisher were used for -5 min only, to avoid relief. The best etching results were achieved with

Jan 1, 1969

By Herbert Clark Hoover, Lou Henry Hoover

SINCE I have written of the varied work of pre- paring the ores, I will now write of the various methods of smelting them. Although those who bum, roast and calcinea the ore, take from it something which is mixed or combined with the metals ; and those who crush it with stamps take away much ; and those who wash, screen and sort it, take away still more; yet they cannot remove all which conceals the metal from the eye and renders it crude and unformed. Wherefore smelting is necessary, for by this means earths, solidified juices, and stones are separated from the metals so that they obtain their proper colour and become pure, and may be of great use to mankind in many ways. When the ore is smelted, those things which were mixed with the metal before it was melted are driven forth, because the metal is perfected by fire in this manner. Since metalliferous ores differ greatly amongst themselves, first as to the metals which they contain, then as to the quantity of the metal which is in them, and then by the fact that some are rapidly melted by fire and others slowly, there are, therefore, many methods of smelting. Constant practice has taught the

Jan 1, 1950

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Edgar C. Bain

Jan 1, 1932

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in. a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a. previous paper.' The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques. The general geo1ogy of the Coeur d'Alene district, including a detailed description of the rock types encountered, has been comprehensively treated by Ransome and Calkins' in their classic paper, and only local background description, therefore, is felt to be appropriate here. The Hercules deposit transects a portion of the trough of a broad south-trending synclinorium which has been greatly complicated by faulting. More locally, it lies within a block of ground bounded on the east; by the O'Neil Gulch fault, a steep north-south overthrust of considerable magnitude, and on the west by a monzonite stock, the outcrop of which is 1/2 mile or more wide and 5 miles long. The country rock is composed of thin to medium-bedded argillites and argillaceous quartz-ites of the Prichard and Burke formations, the oldest members of the Pre-cambrian Belt Series of sediments in the area, believed to be of Algonkian age. The contact between them is a conformable gradation. The argillite is colored gray to tannish-gray and is fine-grained, compact, and generally massive in structure. Under the microscope the unaltered argillite is seen to be composed principally of anhedral quartz and a few feldspar grains which were at one time presumably partly rounded sand grains, but as a result of recrystallization and cementation by silica, the interstices are now almost obliterated and quartz grains show crenulate boundaries. The sizes of these crystals vary from 0.5 mm down to 0.1 mm in greatest dimension. In all specimens sericite comprises 10 to 20 pct of the rock and is present abundantly between most of the grains as flakes or shreds which vary considerably in size. Sometimes they form a fine felt-like mat or aggregate, and sometimes flakes are seen which appear to be good muscovite. In some specimens, separated rhombic-shaped carbonate grains are abundant, and in some instances these have been changed to sericite. Mining operations to date have explored the Hercules vein to a maximum vertical depth of 3600 ft below its outcrop, and along a maximum strike-length of 3600 ft on certain of the lower mine levels. The main orebody is irregular in outline, extending over a variable strike-length of 400 to 1500 ft; and it is intersected by a strong transverse fault that has been traced from the surface to the bottom level. This has been named the Hercules fault, and apart from the vein itself, it is the most prominent structural feature in the mine. There is good evidence that it existed prior to the introduction of ore solutions and may have influenced ore deposition, but it was also the locus of important post-ore displacement and shows a progressive right-handed horizontal component reaching 200 ft on the deeper levels. Its vertical component is not definitely known but may be considerably greater. The fault strikes 20° N to 50° E and dips westerly at angles of 70" to 45", flattening in dip where it crosses the original orebody from east to west between 1000 and 1600 ft below the surface. At about 3000 ft in depth the Hercules fault is joined by a vertical fault of similar strike, and the major post-ore dis-placement below their junction is taken up along this vertical branch of the structure, now called the Mercury fault. Recent work has been concentrated in this vicinity. Another structural feature of special geologic interest, though of little economic importance, is the occurrence of a porphyritic dike in this area. This lies a short distance above the Hercules fault, essentially parallel to it, and is 5 to 15 ft in thickness. It appears at first glance to cut the mineralization, suggesting push-apart relationship, but small stringers of the vein minerals have been observed to penetrate the dike for a matter of inches at several points. The dike is thought to be related to the monzonite intrusion. A vertical longitudinal projection of the mine is shown in Fig. 1, which illustrates most of the features discussed above. The Hercules vein was deposited along the course of a strong, persistent shear zone that now appears as a braided network of gouge seams running through more or less crushed and shattered country rock. It strikes 70° N to 80° W and dips southerly at an average of 75". Barren parts of the structure vary in width from less than 1 ft to more than 15 ft. The width of mineralized segments may be double that. Although the evidence is not conclusive, pre-mineral, normal movement along the zone may be 1000 or 1500 ft. The horizontal component is unknown. Post-ore movement appears to have been

Jan 1, 1954

By Reno H. Sales

Jan 1, 1914