Search Documents

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By C. M. Weld

(Cleveland Meeting, October, 1912.) IN the course of my professional work in China during the fall of 1907, I had an opportunity to visit the iron-ore mines at Ta-yeh in Hu-pei province (long. 114° 50' E., lat. 30° 20' N.). It occurs to me that a rescript and discussion of my notes taken at that time should be of interest, particularly as supplementing the exceedingly interesting recent paper-of Thomas T: Read on The Mineral Production and Resources of China.1 Ta-yeh is situated near the right bank of the Yangtze river. The mines are at an average distance of about 16 miles from the river-port Shi-hui-yao, which in turn is some 70 miles S-E. of Hankow. The ores are shipped to the works of the Han-Yeh-P'ing Iron & Coal Co. at Hanyang, as also very largely to the Japanese government iron- and steel-works at Wakamatsu, Japan. Smaller quantities have been exported to the Pacific coast of the United States. These ore-deposits have been briefly noticed in a number of publications, but, so far as I know, Mr. Read's description, in his chapter on the iron-ores of the Chinese Empire,2 contains the first attempt to define their geological character. In his more recent paper Mr. Read follows very closely the text of his earlier description. To quote briefly from the recent paper, he says : " The iron-ores at Ta-yeh . . . . lie along the contact between a marble and an intrusive body of a dark-gray syenitic rock." He refers to a figure which exhibits in plan, but not in section, the relative positions of the syenite, ore-bodies, and limestone. The contact is seen to trend approximately E-W., with the syenite on the north and the limestone on the south. " The syenite lies to the north of the marble, and a few miles farther north the marble again' appears, iron-ore again being present along the contact." No litho- 1 Bulletin Bulletin No. 63, March, 1912, pp. 293 to 343. 2 The Iron Ore Resources of the World', vol. ii., p. 913 (Stockholm 1910).

Oct 1, 1912

By Henry Howe

W. E. RUDER, Schenectady, N. Y.-In 1913 I presented a paper before this society on Grain Growth, and at that time it seemed to me that the only explanation for grain growth was that of critical strain. I do not think I published the photographs at the time, but I made some experiments on the effect of stretching sheets of metal. This allowed for fairly accurate determinations of the amount of cold deformation, At the time I worked-with silicon steel because one could see the change in grain growth with the naked eye. I stretched about 10-samples from 0.5 per cent. to 10 per cent., and, after heating to 1,050° C., I found that the maximum grain growth occurred at about 2 ½ per cent. cold deformation. This I designated "the critical strain" for maximum grain growth. About a year ago I talked with Prof. Jeffries, who explained to me his ideas of grain growth. It occurred to me that it would be a very easy thing to check the strain hypothesis against the strain and temperature hypothesis, if we took a certain number of these strips, strained exactly alike and heated to different temperatures; in that case the maximum grain growth ought to appear at a different percentage of deformation for each temperature. These experiments showed that there was, as Mr. Jeffries shows in his present paper, a decrease in germinative temperature with increased cold deformation. The samples were stretched from ½ to 8 per cent. and heated for 10 hr. in hydrogen. Samples were introduced into a furnace previously heated to temperature. A maximum grain growth was obtained at 5 per cent. deformation, when heated to 750° C.; at 2 ½ per cent. when heated to 800' C.; at 1 1/4 per cent., if heated at 950°C.; and at 5/8 per cent.. when heated at 1,100° C. This shows very clearly that the germinative temperature decreases with the increase in cold deformation. The growth was very much more marked, however, at the high temperature, i.e., the grain grew more rapidly and attained a much larger size than at lower temperature. In considering the photographs (Fig. A) those along the lateral edges should be ignored because.

Jan 4, 1917

Discussion of the paper of G. K. Burgess and J. J. Crowe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2537 to 2591. HENRY M. Howe, New York, N. Y. :-I think we can hardly rate the importance of the entry of the Bureau of Standards into our field. There is no body in the world that is better fitted to undertake this work than that Bureau, and it is work which really calls for the aid of some national organization. The skill and care with which this work has been done speaks for itself. It is very striking that within a very few months the distinguished English investigator, Professor Carpenter, of whom I spoke before, thought that he had disproved the existence of beta iron by proving that the A2 retardation which Professor Burgess has now demonstrated did not occur. Dr. Burgess's demonstration of the existence of. this retardation makes the existence of beta iron very probable, in my opinion. Osmond used to call beta iron " decipuum." You knew of its existence as you know of the existence of certain planets, only by the perturbation which it caused. Certain phenomena could not be explained, except by assuming the existence of a third allotropic form, beta iron. The evidence that you got was always evasive and susceptible of other explanations, except that which we have to-day, which it seems to me is not capable of other explanation. Professor Carpenter proceeded in the same way that Dr. Burgess has, by taking the heating and cooling curves of exceedingly pure iron, and thought that he had shown that there was no thermal change, no absorption or evolution of heat at the supposed A2 point, and hence that the A2 point did not exist. This he did by a piece of reasoning which I think seems to most of us rather surprising. That is to say, if of ten witnesses, three have seen a thing and seven have not, the evidence of the seven who have not is set aside, and that of the three who have seen stands. In Dr. Carpenter's own experiments under certain conditions he found the A2 change, the heat evolution., under certain others he did not. That is like the three witnesses who saw and the seven who did not see. You can arrange your test so that this change will not become visible or so that it is masked. But though an existent change can be masked a non-existent one cannot be shown. So that the reasoning seemed to me wholly fallacious.

Jan 12, 1913

By J. R. Campbell

It is the purpose of this paper to review somewhat in detail the literature on the subject that is extant, which ought to provoke considerable beneficial discussion. The value of 1 per cent. ash in blast-furnace practice was brought to the attention of the writer when he was connected with the U. S. Steel Corpn. Various groups of blast furnaces in the Pittsburgh district compiled a statement in which the average saving was about 6 c. per ton on pig iron for every 1 per cent. of ash reduction. Later, the same groups of furnaces, when materials had reached a higher price, compiled a statement in which there was a 30-cent saving on pig iron for every 4 per cent. ash reduction in the Pittsburgh district, which was equivalent to 7½ c. for every 1 per cent. ash reduction. In the Chicago district, on long freight hauls of coal and coke from the Pocahontas district, the set-up was 30 c. per ton of pig iron for every 2 per cent. ash reduction, or 15 c. for every 1 per cent. Some years ago, Ralph H. Sweetser, of the American Rolling Mill Co., presented a paper which provoked considerable comment.' To get the matter again before this body a résumé of his computations is given below: Comparison of Pig Iron Costs Ash in Coal. Ash in CoKe, Fixed Carbon in Coke peR Ton OB PIG Iron peN Day, Per Cent. PeR CeNt. Coke. Per Cent. PIG IRon. Lb. Tons 6.00 8.70 89.80 1800 365.0 7.00 10.15 88.35 1860 353.2 Coke with 8.70 Per Cent. Ash Ore mixture, 4144 It). = 1.85 tons @ $5.50.............................. $10.17 Coke, 1800 lb. = 0.90 ton @ $6.50..................................... 5.85 Limestone, 1000 lb. = 0.50 ton @ $1.50................................. 0.75 Labor, $365 per day on 365 tons....................................... 1.00 Supplies and service, $250 per day...................................... 0.68 Overhead, $200 per day............................................... 0.55 Reserve for relining and depreciation................................... 1.00 Total............................................................. $20.00

Jan 1, 1931

By F. H. Spedding

From thermal, metallographic, X-ray, dilatometric, and electrical resistance data a Phase diagram is proposed for the La-C system. TWO compounds are formed, body-centered-cubic Laz C, having a large range of solid solubility, and body -centered-tetrago-nal Lac2 . The former melts incongruently at 1415°C, and at 25OC it has an electrical resistivity about two and one-half times that of bure lanthanum. The latter melts congruently at 2356°C and at room temperature has an electrical resistivity about equal to that of bure lanthanum. The addition of carbon to La lowers the melting Point of La about 115' C, raises the higher (B-Y) transfomzation about 10" C and appears to have no effect on the lower ( a-0) transformation. The addition of carbon appears to lower the oxygen content in the metal and improve the machinability; however, the tendency to oxidize is increased. Two eutectics are formed in the system. The first occurs at 2.2 pct C and melts at 806" C, while the second occurs between Lac2 and C with a melting point of2271"C. PETTERSSON,~ in 1895, was the first to prepare lanthanum dicarbide by heating the oxide with carbon in an electric furnace. He showed that this yellow, crystalline but brittle carbide had a formula corresponding to LaCz and that it reacted with water with the evolution of hydrogen and hydrocarbons and the formation of the hydrated oxide. Von Stackelberg's investigation of the crystal structure of the MCz carbides showed that the lanthanum dicarbide is of the tetragonal calcium dicarbide-type structure. He found the lattice parameters were a = 3.92 and c = 6.56.* Bredig,' using X-ray methods, showed that the room-temperature form of lanthanum dicarbide is stable up to 1750 °C and that above this temperature it transformsoto a face-centered-cubic structure, a = 6.0 ± O.lA, probably of the pyrite, FeSzstruc- typ? The reported discovery of two new cerium carbides, suggested that a corresponding face-centered-cubic lanthanum monocarbide and a body-centered-cubic lanthanum sesquicarbide might exist. This paper describes work on the lanthanum-carbon system which is part of a study of the rare earth metals and their alloys now in progress in this laboratory. EXPERIMENTAL PROCEDURE Source of Materials—The lanthanum metal was prepared at the Ames Laboratory by metal1o;hermic reduction of the fluoride with calcium metal. The results of spectrographic and chemical analysis indicated the presence of 0.01 pct Y, Al, Cu, Fe, and Si; 0.02 pct Ca and Mg; 230 ppm C; and 115 ppm N. The carbon used was of two types: 1) "National Special Graphite Spectroscopic Electrodes," and

Jan 1, 1960

R.. B. T. KILIANI, New York, N. Y.-I do not care to discuss Mr. Taggart's paper in the light of theory, as that has been very well done by Prof. Bell,1 but I should like to criticize some of his conclusions, in the light of actual operating practice at plants all over the country. 1. Mr. Taggart's first conclusion is that in crushing average ore, the character of the gangue has little effect on the efficiency of the mill. This, I believe, is not in accordance with the usual practice, since in crushing a hard ore the capacity will be much reduced below what it would be with a softer ore, while the power consumed will be practically independent of the character of the ore, being proportional only, to the load of ore and balls in the mill. 2. Mr. Taggart's second criticism is that the Hardinge mill is not suitable for grinding soft, tough material. In answer to this I might mention that the mill is being used for grinding tough, dnctile material, such as metallic aluminum, and also for grinding licorice root. 3. He says that the ball-mill works more efficiently on material of intermediate size, say 1/2 to 3/4 in., than on either coarser or finer feed.. This is true as to coarser feed. For the most efficient work, I believe that a ball-mill should be fed with material not coarser than 1 1/2 in.; it' will handle material up to 3 and even 4 in., but the reduction from 3 or 4 in. to 1 1/2 in. can be done much more cheaply and efficiently by rolls or disk crushers than in the ball-mill. 4. As to Mr. Taggart's fourth conclusion, that a greater ratio of reduction can be expected with feed of an intermediate size than with a coarse feed, I have not enough information to express an opinion. 5. His next conclusion is that steel balls are much more efficient crushing media than pebbles. Steel balls are undoubtedly more efficient for crushing coarse feed. On fine material they are also more efficient as to tons per horsepower crushed to 10-mesh, but on fine material I think it will be found that flint pebbles are cheaper than cast-iron balls, per ton of ore, although there will be a saving in power per ton by using cast iron instead of flint. The increased cost of crushing with cast iron will be due to the higher cost of iron at the present time. 6. Mr. Taggart's sixth conclusion coincides with present practice, that steel balls will grind as fine or finer than pebbles when working on the same feed.

Jan 1, 1918

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

C. A. ROSE, New York, N. Y. (written discussion *).-Without doubt the excellent results obtained at Ajo will cause surprise among metallurgists; 75 per cent. average capacity and 80 per cent. extraction during the first year of operation of a plant using a new metallurgical process are figures that speak for themselves. It is obvious that the most troublesome feature of the process is the fouling of solutions. The effects of this are most evident in the electrolytic tank house; but apparently the solutions are so heavily loaded with salts that their dissolving power is also impaired. This is indicated by the fact that copper comes into solution during washing after the leaching of the ore is completed, as shown by the decreasing ratio of acid to copper in the various washes tabulated in Table 4, and also by the fact that 4.9 per cent. of the total copper in the ore remains in the tailings in a soluble form. Even though the extraction in leaching and the ampere efficiency in electrolysis would be benefited by keeping the salts in solution at a lower concentration, it is doubtful whether it would pay to decrease these salts by discarding more electrolyte without other changes in the, process, since this would increase the amount of cement copper produced, which is already very large. If, however, it would not disturb the process otherwise, this object could be accomplished by increasing the range of electrolysis, so that solution going to the tank house would contain, say, 4 per cent. copper and 1 per cent. acid, and the solution returned to the leaching plant 1 1/2 per cent. copper and 4.8 per cent. acid, and by increasing the volume of solution to be discarded, this to be taken from the electrolyzed solution returned to the leaching plant. By this arrangement, more salts will be removed from the system per ton of cement copper produced; and if sufficient solution is discarded to keep the iron content down to 1 1/2 per cent. it would he feasible to recover the copper from

Jan 4, 1919

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By J. E. Chappelear

We are concerned with the problem of calculating the forces produced by passing waves on a submerged object (in particular a drilling barge) located on the ocean floor. We employ the linearized theory of waves (the Airy1 theory), since solutions are generally more easily obtained in such a theory. It will be indicated how an approximate solution to the problem can be obtained for waves of finite height by use of a linear combination of Airy waves. We shall assume the submerged object has an infinite length, thus neglecting diffraction and making the problem two-dimensional. We find that there is not a considerable difference between our solution and the usual engineering solution. The force, as a function of time, is plotted in Figs. 4 and 5, together with the usual solution for easy comparison. So far, no experiments have been found to compare with the results. As will be shown, the calculations can be extended to waves of finite height (Stokes2-Struik3 waves) in an approximate fashion. This can be done by calculating the force produced by each Fourier component of the wave, separately, and omitting the coupling between the various harmonics produced by Bernoulli&apos;s theorem. The problem and its boundary conditions will be briefly stated. We seek a function, +, the velocity potential, which is harmonic, ?2?=0...........(1) and which satisfies the boundary conditions ??/?n =0 .......(2) (the normal derivative of + is zero) on the ocean floor and the sides of the barge, and s??/?y = ?..........(3) on the ocean surface, where s = g/w2........(4) The physical reasons for these choices and an interpretation of ? are given by Lamb.&apos; As previously stated, we assume also that the problem is two-dimensional. We set up our coordinates such that x = 0 is the center of the barge and y = 0 is the ocean floor. The coordinates are shown in Fig. 1, together with the location of the barge on the bottom. Our solution may be decomposed into a function which is symmetric about x = 0,?e, and one which is antisymmetric, +,, ? = ? + ?o...........(5) Thus directly above the barge we have as boundary conditions that for x = 0, ?o = 0, ...........(6) and ??e/?x = 0........(7) Now, far from the barge, we have that (for x positive and assuming the waves are incident from the left) ?e ? Ae cosh ky cos k (x + a) , . . . (8) and ?e ? Ao cosh ky cos k (x + ß) . . . . (9) where + means ". .. approaches ... for x large." Let us put Ae, Ao, and k equal to one, and remember that, in accordance with the derivation of Eq. 3, a sinusoidal time factor is to be supplied. Then we may rewrite Eq. 8 for ?e, and we find that

Jan 1, 1958