Search Documents

By E. H. Dix

The work of Merical and other investigators indicates that the phenomenon of age-hardening in alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum Company of America to determine the functions * Metallurgist, Aluminum Research Laboratories. f Metallurgical Division, Aluminum Research Laboratories. Formerly with Metallurgical Division, Aluminum Research Laboratories. 1 P. D. Merica, It. G. Waltenberg and H. Scott: Heat Treatment of Duralumin. U. S. Bur. Stds. Sn. Paper 347 (1910). 2 M. Gayler: Constitution and Age-Hardening of Alloys of Aluminum with Copper, Magnesium, and Silicon in the Solid State. Jnl. Inst. Met. (1922) 28, 213. W. Fraenkel: Vergutbare Aluminiumlegiengen. Ztsch. Melallkunde. (1920) 12, 427. E. H. Dix, Jr.: Note on the Microstructure of Aluminum-Iron Alloys of High Purity. Proc. Amer. Soc. Test. Mat. (1925) 26, Pt. 2, 120. E. H. Dix, Jr. and H. H. Richardson: Equilibrium Relations in Aluminum-copper Alloys of High Purity. Trans. A. I. M. E. (1926) 73, 560. E. H. Dix, Jr. and W. D. Keith: Equilibrium Relations in Aluminum-manganese Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1927) 315. E. H. Dix, Jr. and A. C. Heath, Jr.: Equilibrium Relations in Aluminum-silicon and Aluminum-iron-silicon Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1928) 164. E. H. Dix, Jr. and F. Keller: Equilibrium Itelations in Aluminum-magnesium Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1920) 351. E. H. Dix, Jr., F. Keller and R. W. Graham: Equilibrium Relations of Aluminum-magnesium Silicide Alloys of High Purity. Trans. A. I. M. E., Inst. Met. Div. (1931) 404. W. L. Fink and K. R. Van Horn: Constituents of Aluminum-iron-silicon Alloys. Trans. A. I. M. E., Inst. Met. Div. (1931) 383.

Jan 1, 1932

By G. G. Marino, J. W. Mahar

This paper provides an understanding of the behavior and potential damage of homes resulting from sag-type mine subsidence. This is done with extensive research of numerous case histories in Illinois collected by the authors. The house response to subsidence-induced ground displacements are summarized and evaluated. A damage level criteria, specifically developed for residential structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 1, 1986

By Walter S. White

The Michigan native-copper district has produced about 5,400,000 tons of copper since mining began in 1845. The copper occurs primarily as open-space fillings and replacements in amygdaloidal flow tops and conglomerate beds of the Portage Lake Lava Series, of middle Keweenawan age. Secondary minerals with which the copper is associated include microcline, chlorite, epidote, pumpellyite, prehnite, quartz, and calcite; zeolites, other than laumontite, are not abundant. A zonal pattern of the secondary minerals transects bedding and suggests regional metamorphism mainly to the grade of the prehnite-pumpellyite graywacke facies of Coombs. Most of the major copper deposits are near the upper limit of abundant quartz in this zonal pattern. The distribution of copper in both amygdaloid and conglomerate deposits is controlled partly by primary permeability of the rocks and partly by later tectonic fracturing that was concentrated in the mechanically weak flow tops and sedimentary beds. Ore shoots and deposits are therefore controlled partly by primary structural features, such as areas of thick and thin fragmental amygdaloid or the boundaries of conglomerate lenses, and partly by regional structure: a number of ore deposits are in synclinal downwarps. The copper-bearing solutions that formed the deposits were ascending. They may have come from a large concealed intrusive, or may have been driven out of the porous tops of lava flows when the rocks were compacted and metamorphosed at great depth in the central part of the Lake Superior syncline. The second hypothesis seems more consistent with the widespread distribution of the copper, its relation to mineral zoning that represents truly regional metamorphism, its native state, and the likelihood that copper deposition was later than most or all of Keweenawan volcanism.

Jan 1, 1968

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS of assaying were explained in the last Book, and I have now come to a greater task, that is, to the description of how we extract the metals. First of all I will explain the method of preparing the ore1 ; for since Nature usually creates metals in an impure state, mixed with earth, stones, and solidified juices, it is necessary to separate most of these impurities from the ores as far as can be, before they are smelted, and therefore I will now describe the methods by which the ores are sorted, broken with hammers, burnt, crushed with stamps, ground into powder, sifted, washed, roasted, and calcineda.

Jan 1, 1950

By Donald A. Brobst

The minerals barite (BaSO4-barium sulfate) and witherite (BaCO3-barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1980 consumed at least 90% of the world's production of 8.8 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite is much less common and abundant than barite, although it is more desirable in many ways as a raw material for the production of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir conditions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemically, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite homogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber industry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and linoleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other substances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weigh down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1983

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By Gordon E. Agar, David M. Hopstock

This paper describes the procedures and results of a series of experiments conducted to determine the depressing effect of sodium, calcium and magnesium ions on the amine flotation of quartz. It also presents an analysis of the experimental results by the electrical double layer theory. The flotation of quartz with primary amines has been practiced on a large scale in the phosphate industry for many years. Some glass sand —and recently iron ore — has also been treated by this flotation technique. These applications have been highly successful and demonstrate that a complete mastery of all the details of an operation is not needed to achieve an economic success. There are times, though, when it becomes important to recognize, both qualitatively and quantitatively, the effects of some previously ignored variables. The effects of cations on the amine flotation process, particularly those ions that contribute to water hardness and abound in sea water, are a case in point. In conjunction with the development of a cationic flotation reagent for separating quartz from apatite, it became necessary to quantify the influence of calcium and magnesium on the separation. In order to strengthen and broaden current understanding of the flotation process, the results were interpreted by means of the electrical double layer theory. THEORETICAL BACKGROUND Assume that, given the same equipment, procedure, and time, the recovery of quartz by amine flotation is a function of only the adsorption density of aminium ions in the Stern layer, i.e., that for any given adsorption density there exists only one recovery percentage. By the Stern-Grahame treatment of the electrical double layer,'-' for any ionic species in a solution in equilibrium with quartz,

Jan 1, 1969

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff" backfill to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By N. J. Grant, C. Stein

A more complete determination of the chromium-rich portion of the Cr-Ni phase diagram was made, based in part on resistivity measurements. The existence of a eutectoid reaction at 1215°C,made,based in addition to the previously reported eutectic reaction at 1343°C, was confirmed. Metallographic studies, lineal analysis, and diffusion-couple evidence were utilized to support Metallographicand extend the findings of the resistivity measurements. Delineation of the a chromium solvus line shows that the maximum solubility of nickel in a chromium decreases rapidly from 25 wt pct Ni at the eutectoid temperature to 16 wt pct. Ni at 950°C. IN recent years alloys of high chromium and nickel content have become of more interest as better performance of metals at higher temperatures is sought. It has become increasingly important, therefore, that the Cr-Ni binary diagram, which is composed of two of the elements commonly found in many high temperature alloys, be known more accurately. In particular, the chromium-rich portion of this diagram has for a long time remained incompletely determined and has been reported in the literature with a great deal of conflicting evidence. In general, electrolytic chromium of nominal purity was used by most of the earlier workers, who, except for Jenkins et al., made no further attempt to purify the metal. In the present redetermination of the chromium-rich portion of the Cr-Ni phase diagram, every effort was made to use the purest component metals available and to retain this purity throughout the preparation of the alloys and their subsequent handling. Early work by Voss, Bain," and Phebus and Blake4 indicated that the Ni-Cr binary diagram was a simple eutectic system with rather extensive terminal solid solutions. Later, Nishigori and Hamasumi," Tasaki, Weaver and Jellinghaus,' Matsunaga, and Jette, Nordstrom, Queneau, and Foote attempted to determine the limits of the phase fields. Except for Jette and coworkers, the other investigators agreed that the temperature of the eutectic reaction occurred between 1320" and 1340°C and at a composition of 50 or 51 pct Cr. There was, however, considerable disagreement as to the melting point of the chromium-rich alloys and the limits of the solid-solution fields. As a result of the studies of Jenkins et al., the liquidus and solidus curves up to 80 and 90 pct Cr, respectively, were outlined. In addition, the solid-solution phase fields at higher temperatures had been investigated and showed only two phases. The boundary of the chromium-rich a phase was not determined precisely according to these authors, but indications were that it tended to confirm the earlier work of Nishigori and Hamasumi. A more recent investigation by Taylor and Floyd,'" using X-ray methods, essentially corroborated the diagrams proposed by Jenkins et al., and by Wise and Eash (see Fig. 1). Again, no indication of a third phase in the chromium-rich portion of the diagram appeared. The earlier observations, however, are not substantiated by the modifications to the Ni-Cr binary diagram proposed by Bloom and Grant." In the investigation carried out by Bloom and Grant, X-ray methods showed that an eutectoid reaction existed at approximately 1180°C, in addition to the eutectic reaction at 1343°C (see Fig. 1). Their determination of the melting point of pure chromium was 1930°C (later revised to 1903"C)." Experimental Procedure and Results The chromium used for this study was electrolytic chromium, made available by the United States

Jan 1, 1956

By William H. Bassett, C. J. Snyder

Cable sheaths made from common lead have been used to protect underground cables since the beginning of the power-cable industry. Only within the last few years, however, has a systematic study of the production methods and of the causes of failures in cable sheathing been undertaken. Recent increases in the use and demands for service made upon power cables have emphasized the importance of high-quality cable sheaths. It was customary for the users to attribute the cause for their sheath failures to the lack of purity of the lead, but this contention has not been borne out by field and laboratory inspection of the sheaths. During the past two years the writers have had an opportunity to examine various types of sheaths that were removed from power cables after failure. These samples were obtained from various parts of the country and represent, it is supposed, the production of the principal cable manufacturers. Aside from corrosion, the common field difficulties can be classified either as mechanical or structural, as outlined below, and when structural irregularities are found they can all be attributed to manufacturing causes and in no way reflect the purity of the lead. Clasxification of Cable Sheath Failures Other Than Corrosive Mechanical Irregularities A. Splits caused by excessive internal pressure B. Injuries such as nail holes, cuts, tsars, etc. C. Intercrystalline cracks caused by vibration Structural Irregularities A. Splits C. Voids in wall of sheath a. Caused by imperfect welds a. Blisters 13. Holes through sheath b. Laminations a. Caused by yellow oxide inclu- D. Questionable structures sions in sheath wall a. Prominent flow lines b. Blowouts by entrapped gases b. Large areas filled with suboxide during manufacture c. Scattered yellow oxide or dirt C. Caused by inclusions of dirt and

Jan 1, 1933

By Johann F. Kerl

Autogenous batch grinding tests were performed in laboratory-scale tumbling mills with magnetite, limestone, and sandstone pebbles. The influence of pebble size, feed size, mill speed and loading, and grinding time on the fineness of grinding was investigated. Comparisons were made with the results from ball mill grinding experiments.

Jan 1, 1972

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By AIME AIME

T HE Institute of Metals Division and the Iron and Steel Division will meet jointly at the Stevens Hotel, Chicago, during the week of the American Metals Congress, Sept. 22-26. The Iron and Steel Di- vision of the American Society of Mechanical Engineers, the American Society for Steel Treating and the American Welding Society meet at the same time. but the sessions have been arranged to conflict as little as possible. A rich program of papers and plant visits has been arranged for the members and guests of the two Institute Divisions. The annual dinner and a pro- gram of entertainment are being arranged by the Woman's Auxiliary of the Chicago Section. Members are urged to register immediately up011 arrival and to make dinner and plant visit reservations at the same time.

Jan 1, 1930

pAbad, Leopoldo F., Min, Engr,, Div. of Mines, Bureau of Science Manila, P. 1. '23 Abadilla, Quirico A,, Geol., Lago Pet. Corp Box 172, Maracaibo, Venezuela, '20 Abbey, Robert Graham, The W. W. Sly Mfg, Co Train Ave., Cleveland, Ohio. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Mexico, '28 Abbott, Clarence E., Mgr., Mines & Quarries, Tenn, Coal, Iron & R. R, Co,, 1242 Brown Marx Bldg,, Birmingham, Ala. '04]

Jan 1, 1928

By N. J. Sather

The history of the Bunker Hill mine dates back to August 26, 1885, when Noah S. Kellogg found the outcrop of the Bunker Hill orebody on the hillside of Milo Gulch above the present town of Wardner, Idaho. A small concentrator was erected in 1886, and before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d'Alene Lake. After ten years of production, an interest was purchased in the Tacoma smelter at Tacoma, Wash., to which the entire output was shipped. In 1916 and 1917, a modern lead smelting plant and refinery was erected, and a modern electrolytic zinc reduction plant was built in 1927-1928 by the Sullivan Mining Co. which was 50 pct owned (and now totally owned) by the Bunker Hill Co.

Jan 6, 1961

While the production of this state has not realized the early hopes that this coal would replace eastern coal on the Pacific Coast, it has been steady though small. Nearly all of the tonnages given are from Goodyear's, The Coal Mines of the Western Coast of the U. s., a carefully com- piled and accurate account of the development of the industry along the Pacific. [ ]

Jan 1, 1942

The Library of the above-named Societies is open from 9 A.M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The tine spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1917

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986