Search Documents

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

By H. H. Kellogg, T. R. Ingraham

Three anhydrous zinc sulfates have been identified. They are: ZnSO,(a), stable below 1007°K; ZnS04(/3), stable above 1007OK; and ZnO.ZZnSO,. The decomposition pressure of each sulfate has been measured and the following relations calculated from the results: The measured data have been combined with the known themzodynamic properties of ZnS, ZnO, Zn, SO,, and SO, to yield univariant and bivariant phase diagrams for the system Zn-S-0. The application of these diagrams to problems of roasting zinc concentrates is discussed. PRESENT knowledge of the equilibrium chemistry of the system Zn-S:O, so essential to scientific control of zinc-blende roasting, is deficient in several respects. A basic sulfate of zinc has been reported by many investigators, but its composition is in doubt and its thermodynamic properties have not been measured. Our scanty knowledge of the properties of the normal sulfate at roasting temperatures is based on old and inexact studies. A crystal transformation in the normal sulfate, involving a sizable heat effect, has been noted by several investigators but has never been quantified. The studies reported herein were designed to fill these gaps in knowledge and to make possible a reasonably complete thermodynamic description of the system Zn-S-0 at roasting temperatures. The results make possible a far more exact understanding of zinc roasting chemistry than was hitherto possible. EXPERIMENTAL The principal experimental technique employed was the measurement of the total gas pressure developed from decomposition of either ZnSO, or ZnO2ZnS0, in a closed system. The apparatus employed was essentially the same as that described by Warner and lngrahaml and Flengas and tngraham.' The unusual feature is a flexible Pyrex bellows used to separate the reaction gas mixture (S03, SOz, and 02) from the mercury in the manometer and thus prevent corrosion of the mercury by SO3. The bellows operates without evidence of hysteresis and, barring accidents, may be used for several months. The response of the bellows varies from manometer to manometer, but is generally of the order of 0.6-cm displacement for a l-cm change in pressure. The response for all manometers has been linear over the range 0 to 1 atm. To prevent condensation and polymerization of sulfur trioxide, the bellows-manometer was maintained at 100.0" * 0.5" by a circulating bath of silicone oil. The connecting tubing between the manometer and the furnace was maintained at 100.0" * 0.2"* also, with a stirred air bath. The open end of the manometer was connected with a chamber which was maintained at a known pressure. The pressure could be varied so that readings of the height of the mercury column, measured with a cathetometer, could be made with both rising and falling mercury column. By using the average of the readings, any error due to sticking of the mercury column was minimized. The sample was placed in a 2-in.-long platinum boat formed into the shape of a half-cylinder. The sample was prepared as a fine powder and pressed against the inner wall of the platinum boat. A silica thermocouple well, covered with a platinum sleeve, was placed lengthwise along the center of the boat. The temperature of the sample was read on a calibrated Pt-10 pct Rh theirnocouple. The temperature profile of the furnace was constant within ± 0.2 C over the length of furnace occupied by the sample. The horizontal furnace used to contain the sample and the quartz reaction tube was electrically heated, with the control thermocouple placed 1/4 in. from the windings. A Brown Pyro-O-Vane temperature controller with a 3-sec response time was used to maintain the furnace temperature. Before beginning a run, the apparatus, including the bellows manometer, was thoroughly washed in sib with acid and distilled water to remove any

Jan 1, 1963

By Robert M. Grogan

Fluorspar is the commercial name for fluorite, which is the mineral having the composition CaF2, calcium fluoride. Its valuable properties are due to its content of fluorine, and it is the only important commercial source of that element. The name is derived from the Latin fluere, to flow, because the mineral melts easily and is a good flux. History The mineral has been known since Greek and Roman times, when it was used for drinking cups and ornamental slabs. Various peoples including the Chinese and the American Indians have carved ornaments from large crystals. Its usefulness as a flux was known to Agricola, who wrote about it in 1546.1 Mining began in England about 1775 15 and at various places in the United States during the period 1820 to 1840.28 Substantial production was achieved first in the period 1888 to 1900 in consequence of the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage was stimulated by growth in the steel, aluminum, chemical, and ceramic industries and accelerated by World Wars I and II. The organic fluorides called "Freons" entered the picture in 1931, and the use of anhydrous HF as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920's, a differential flotation scheme for separating fluorspar from galena, sphalerite, and other minerals in the 1930's, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940's were outstanding technological contributions that enabled increased production of fluorspar concentrates. Composition and Properties Fluorite in its purest form contains 51.1 pct calcium and 48.9 pct fluorine. Substitution of small percentages of cerium and yttrium for calcium have been noted.4 Mechanical inclusions of gases and fluids such as petroleum and water, and of other solid minerals such as pyrite, marcasite, and chalcopyrite are common. The fluorspar of commerce contains attached and admixed mineral impurities, chiefly calcite, quartz, barite, celestite, and various sulfides. It is interesting that the purest commercial form in which the mineral is sold, acid grade concentrate, contains a minimum of 97 pct CaF2, and as such is of comparable purity to many reagents used in chemical laboratories. Fluorite has a marked tendency to occur in large, well-formed crystals sometimes six to ten inches on a side. It crystallizes in the isometric system, frequently forming cubic and octahedral crystals or combinations thereof. The mineral also occurs in massive and in earthy forms, and in crusts or globular aggregates with radial fibrous texture. Crystalline fluorspar exhibits a great array of colors, from colorless and water clear to yellow, blue, purple, green, rose, red, bluish and purplish black, and brown. The colors are often arranged in alternating bands parallel to cube faces. They may be altered by exposure to X-rays, heat, ultraviolet light, and pressure, and are caused by a variety of factors including the presence of trace impurities and displaced ions in the lattice. Sometimes the changes induced by X-rays can be reversed by ultraviolet radiation. The mineral has a hardness of 4, and is the model of that hardness on the Mobs scale.

Jan 1, 1960

The following is a partial list of members and guests who called at Institute headquarters during the period Sept. 10, 1917, to Oct. 10,1917. Thomas J. Adams, Rahway, N. J. Leon Root Long, Tirapata, Peru, So. Am. L. W. Bahney, Waterbury, Conn. F. M. McClenahan, Ben Avon, Pa. D. W. Brunton, Denver, Colo. E. Francis McCrossin, Birmingham, Ala. J. R. Buchanan, Pasadena, Cal. P. S. Moses, Savannah, Ga. R. C. Canby, Wallingford, Conn. William A. Nelson, Cartersville, Ga. Paul R. Cook, Zaruma, Ecuador. Edmund Newton, Minneapolis, Minn. F. Crabtree, Pittsburgh, Pa. Askin M. Nicholas, Porrington, N. S. W., J. T. K. Crossfield, Chuquicamata Chile. Australia. Wayne Darlington, Georgetown, S. C. E. G. Norton, Chicago, Ill. R. W. Deacon, Elizabeth, N. J. M. L. O'Neale, Coal City, .Ala. Alexander Deussen, Houston, Tex. W. E. Pomeroy, El Paso, Tex. G. G. Dobbs, Bessemer, Ala. Joseph P. Ruth, Denver, Colo. E. B. Durham, Canonsburg, Pa. Gustavus Sessinghaus, Denver, Colo. L. H. Duschak, Berkeley, Cal. A. L. Sweetser, Boston, Mass. F. A. Fahrenwald, Cleveland O. G. M. Taylor, Colorado Springs, Colo. A. H. Fay, Washington, D. a. Allan G. Waite, Dragoon, Ariz. C. L. French, Brooklyn, N. Y. H. Vincent Wallace, Los Angeles, Cal. Carlos F. Galan, Riverside, Mex. H. A. Wentworth, Boston, Mass. Herman Garlichs, St. Louis, Mo. Alfred W. G. Wilson, Ottawa, Canada. Ernest Klepetko, Anaconda, Mont. Samuel S. Wyer, Columbus, O. D. A. Lyon, Washington, D. C. M. M. Albertson has accepted a position with the McIntyre-Porcupine Gold Mines, Ltd., Schumacher, Out., Canada. James A. Block is now employed by the Ray Consolidated Copper Co., of Hayden, Ariz.

Jan 11, 1917

By John Alden

A CONSIDERABLE PROPORTION of the tonnage of aluminum used today has at some stage during its manufacture, been rolled. I. For one, therefore, was particularly pleased to hear that this Society was to hold a symposium on rolling of nonferrous metals. Metallurgists can well afford to direct their close attention to the metallurgy involved in this important operation. To one who has seen today's high production rolling mills for aluminum it is difficult to realize that the first aluminum rolling mill For sheet was installed a scant 55 yr ago, in 1892. This mill was a three-stand train of 2-high mills, driven by a steam engine and was operated for many years successfully rolling aluminum sheet. Mills for the rolling of aluminum rod were installed in 1899 to meet the demand For manufacture of electrical conductor wires and cables. Bars and rods in straight lengths were also made. While these mills were the first built for rolling aluminum products of these types some rod had previously been rolled on brass and copper mills. Not until many years later, in 1929, however, Were facilities provided for the rolling of structural shapes, such as I-beams and channels. Growth of the aluminum sheet business and the necessity for economical manufacture soon brought the realization of the economies resulting From-the rolling of sheet in long lengths and coiling it. A five-stand continuous mill driven by a steam engine, was in operation late in 1907. This took aluminum slabs coating from

Jan 1, 1948

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

F. E. BACHMAN, Buffalo, N. Y. (Communication to the Secretary) : The investigation so fully described by Mr. Laudig was undertaken with the idea of determining if it is possible to learn by expesiment, without an actual trial in the furnace, what economical results can be expected from the use of a given ore-mixture. The research was necessarily preliminary, and the results obtained are only to be depended upon so far as they relate to the samples treated. With the exception of the ores obtained from the stock-piles of the Buffalo Furnace Company, and several samples taken at a neighboring furnace, there is no certainty that the ores represented the average shipments of any mine. For this reason the publication of the names of the ores might do producers a great injustice. The names of the ores arc therefore withheld, and their identity is further .veiled by leaving out of the analyses the phosphorus-contents. The investigation was begun with the preconceived idea that the rate of reduction would be found to be dependent upon the accessibility of the particles of the ore to the action of the reducing-gas. In other words, a spongy, brown hematite or a very fine Mesabi would be the easiest reduced. I had formed a scale with No. 21 first, No. 30 second, No. 1 third, Nos. 5, 24, 25 and the remaining Mesabis fourth, etc , which is sufficient to show how much actual results differ from a judgment based on physical characteristics. The ore expected to be most easily reduced proved to be 25th in the list, while the one placed

Jan 1, 1897

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic loca- tion or seam characteristics, modern raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality, and these objectives may be sought by commencing the preparation of coal underground at the "working face." Under- ground preparation involves choosing those portions of the seam which can be cleaned to satisfy predetermined market requirements involving ( 1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios, and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1 ) seam under development, (2) mining equipment available, and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another, the (1) petrography of the coal in the seam does not remain uniform, (2) character of roof and floor are subject to change, and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution, and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content, and petrography are of considerable interest, and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking, and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal.

Jan 1, 1979

By Walter W. Bradley

AT ONE TIME OR ANOTHER and in greater or less amounts, gold has been mined in at least 40 of California's 58 counties. It may not be inappropriate, by way of introduction, to give a brief historical statement relative to her production of the yellow metal. The presence of gold in the gravels of San Gabriel, San Francisquito, and other streams near Los Angeles, was known and they were worked in a small way by the Indians, at least as early as. 1841' and possibly 1820. -On March 2, 1844, Don Manuel Castanares, deputy for California to the Congress of Mexico, reported' to his government that placers near Los Angeles had yielded up to December, 1.843, a total of 2000 oz. of gold dust, most of which had been sent (via Mexico) to tile United States Mint at Philadelphia.

Jan 1, 1932

By James M. Barker

Sulfur is a nonmetallic element of great physical and economic importance to the world. It is widely but sparingly distributed throughout the hydrosphere, lithosphere, and biosphere. Sulfur is the tenth most abundant element in the universe and eighth most abundant in the sun. In the earth's crust, which is mainly igneous, it ranks 14th, but is eighth or ninth in sediments (Kaplan, 1972; Stanton, 1972). It apparently is very abundant in the core of the earth, because it is a strong chalcophile, and it is fifth in abundance in stony and iron meteorites (Field, 1972) where it occurs as trolite (FeS). In ancient times sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Shelton (1979) summarized most of the common definitions of terms, grades, and specifications for the sulfur industry as follows (with minor additions): Sources of Sulfur: Combined sulfur-Sulfur that occurs in nature combined with other elements. Cupriferous pyrites-Pyrite containing relatively minor amounts of copper sulfide minerals. Hydrogen sulfide-A toxic gas (H2S) occurring in natural gas and petroleum. Involuntary sulfur-Sulfur produced primarily as a result of legislative or process mandates. Native sulfur-Sulfur that occurs in nature in the elemental (uncombined) form. Nonferrous metal sulfides-Copper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfurs-Complex organic sulfur compounds occurring in petroleum, coal, oil shale, and tar sands. Pyrites-Iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfurs-Sulfur in anhydrite and gypsum. Voluntary sulfur-Sulfur produced in response to market forces. Basic Sulfur Products Produced and Marketed: Acid sludge-Contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-Synonymous with crude sulfur. Bright sulfur-Crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-Solid crude sulfur crushed to -8 in. Byproduct sulfuric acid--Sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-Commercial nomenclature for elemental sulfur. Dark sulfur-Crude sulfur discolored by minor quantities of hydrocarbons ranging up to 0.3 % carbon content. Elemental sulfur-Processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-Elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-Elemental sulfur produced from native sulfur sources by the Frasch mining process. Hydrogen sulfide-Associated with natural gas or petroleum and produced at refineries and coke oven plants; used to make sulfuric acid or recovered sulfur. Liquid sulfur-Synonymous with molten sulfur. Liquid sulfur dioxide-Purified sulfur dioxide compressed to the liquid phase. Molten sulfur-Crude sulfur in the molten phase.

Jan 1, 1983

Jan 1, 1898

By Ralph W. Smith

DEVELOPMENT of the lime industry- in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaC03; 0.35 Si02; 0.3 R203; 0.35 MgCO3; 0.3 S03. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ º. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 ½ º the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By Albert Sir Kitson

THE manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In. certain respects they strongly resemble those of India and Brazil, as contrasted with those of Tertiary age in Georgia. Viewed from the present condition of the maganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments; youngest are the products of decay and degradation with the concentration of manganese oxide of both areas. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate amount of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows largely of basic types. To this series I have given the name Birrim. Its age is unknown, for no definite fossils have been discovered in it. As the characteristics of these non-fossiliferous strata at many places are the same as those of strata in many parts of the world that are suitable for the preservation of fossils and that contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim series have normally a northeast-southwest strike and are folded, but not to any very great degree except in certain belts., From the Eastern Province of the Gold Coast they may be traversed across their strike for more than 600 miles to the extreme northwestern corner of the Northern Territories. Thence. they probably extend much further into French Territory.

Jan 5, 1927

By Danforth R. Hale

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the U.S. over the past decade as a man-made mineral and a $3 million crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for “cultured quartz”- that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to U.S. government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezo-electric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can bevaried through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1975

By C. A. Heiland

For a long time it has been known that it is possible to deduce conclusions about the physical constitution of the interior of the earth from the records of natural earthquakes obtained by stationary seismographs. In view of this fact it is surprising how late, relatively speaking, geologic prospecting by seismic methods has been taken up, although the first suggestion was made 40 years ago- that travel-time curves of artificial explosions might be used for the study of the change of the velocity of seismic waves as depth. Further suggestions of practical applications of artificial explosions for geologic purposes were made by Belar,2 by von dem Borne,3 by Benndorf4 and by Galitzin,5 but it was not until 1919 that Mintrop obtained. a patent on the seismic prospecting method which he has applied commercially on a large scale ever since. Dr. Mintrop came to this country with his method at about 1923. Since that time, several. American oil companies have developed seismographs of the mechanical type for the vertical component similar to that of Mintrop's (Humble Oil Co., Dr. Ricker). Other consulting geophysical companies designed other types of seismic devices, the simplest of them for the recording of the first impulse being the geophone (McCollum Geophone Co.). The galvanometric recording method as first proposed by Galitzin is being used (Geophysical Research Corpn.?) and use is being made even of the piezoelectric properties of crystals for portable seismographs (F. Rieber).. There is such an enormous variety of all kinds of portable seismographs, vibrographs, accelerographs, etc., that it is difficult to decide just what kind is preferable. Unfortunately, nothing has been published as yet about American designs of portable seismographs, except the Wood Anderson torsion-seismometer. After Mintrop's design of portable seismographs, other constructions were made.

Jan 1, 1928

By Frank Firmstone

In April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Figs. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised together, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places.

By M. A. Dayananda

Based on the Kirkendall frame of reference, a method is proposed for the determination of atomic mobilities of all the diffusing species in a multicorn-ponent system with a single diffusion couple. The method is based on an atomic mobility model developed on the concept of negligible interactions among the intrinsic fluxes. It is shown in the model that mobilities can be obtained directly from the cumulative intrinsic fluxes past the Kirkendall interface. The proposed method replaces the need for a prior determination of interdiffusion coefficients far the calculation of mobilities. Relations between intrinsic diffusion coefficients and mobilities are derived and the mobility calculations are illustrated with diffusion data in Cu-Zn-Mn alloys at 850°C. ThE concept of "intrinsic flux" with respect to a fixed lattice was introduced "i Darken1 to explain toa Kirkendall effect2 demonstrated by the motion of inert markers during isothermal diffusion in single-phase binary solid solutions. Based on this concept, intrinsic diffusion studies have been made in various binary metallic systems3,4 employing such a lattice frame of reference, commonly referred to as the Kirkendall interface. Similar approaches, both theoretical and experimental, have been presented5"10 to study intrinsic diffusion in multicomponent systems. Based on the direct integration of Fick's law extended to multicomponent diffusion, Philibert and Guy8 proposed a method for the determination of intrinsic diffusion coefficients. For an n-component system, this procedure requires an experimental study with (n — 1) diffusion couples, all having their Kirkendall interfaces at the same compositio;, where n(n — 1) intrinsic diffusion coefficients are defined. This technique has been employed for ternary diffusion studies by Dayananda and Grace" and Guy and Leroy.11 A different approach is recommended by Ziebold and Cooper,12 who have derived relations between interdiffusion coefficients and atomic mobilities employing fluxes referred to the local center of volume. Their analysis is based on the simplifying assumption of negligible interactions among intrinsic fluxes. This assumption has been considered satisfactory for dilute solutions.5"7 The use of this analysis for the calculation of mobilities requires an initial determination of interdiffusion coefficients with a set of diffusion couples having intersecting diffusion paths. It is the purpose of this paper to propose a method that would permit a direct determination of mobilities of all components of a multicomponent system from a single diffusion couple. This method is based on a mo- bility model developed with diffusion fluxes referred directly to the Kirkendall interface, generally identified by inert markers. gen erall, like that of Ziebold and Cooper,12 employs the simplifying assumption that the flux of each component relative to a fixed lattice is caused only by the driving force of its own chemical potential gradient. THE KIRKENDALL INTERFACE Inert markers are employed in diffusion couples to locate experimentally the position of the Kirkendall interface. They are initially placed at the weld interface for "sandwich" couples, or at the original vapor-solid interface for vapor-solid couples. Studies of marker motion in binary systems3'4 with both types of couples indicate that markers remain in a plane of constant composition and move with this plane para-bolically with time. Parabolic marker movements were also observed in ternary Cu-Zn-Mn couples by Dayananda and Grace.10 It is reasonable to expect a similar marker behavior even for diffusion couples with a higher number of components.

Jan 1, 1969