Search Documents

By Karl J. Dreher, Charles C. Hennig, Gregg A. Scott

INTRODUCTION Theodore Roosevelt Dam is a cyclopean-masonry, gravity-arch dam located on the Salt River northeast of Phoenix, Arizona. Construction of the dam began in 1903 and was completed in 1911. The dam is about 85 m high with a total reservoir capacity of about 1.7x109 m3. Raising the dam is now being considered to provide additional water storage and flood control. This paper describes preliminary analyses performed to assess foundation stability for increased loading resulting from raising the dam and reservoir water surface about 12 m. The foundation of Theodore Roosevelt Dam consists of variably metamorphosed limes tones, sands tones, mudstones, and shales. Bedding uniformly strikes nearly normal to the river (N 40º W) and dips upstream at 25 to 30º. The rock is cut by four prominent joint sets as indicated by the joint contour diagram shown in figure 1A. The diagram was developed from surf ace observations and vertical drill core oriented relative to the bedding. Sampling biases account for the differences in concentrations of various joint sets. However, field observations indicate that all sets are relatively prominent, planar, and continuous. SEEPAGE ANALYSES Consistent with practice at the time of construction, no foundation drainage was installed at Theodore Roosevelt Dam. Finite element seepage analyses were therefore performed to study the potential for large uplift pressures in the foundation. The dam has steep abutments and is curved in plan as shown in figure 1B. The effects of modeling the seepage two-dimensionally, radially symmetric about the dam's axis center, and three-dimensionally were therefore com-

Jan 1, 1982

By Joseph C. Platt

It is not the object of the present paper to give a description of the minerals found on Mine Hill, in Sussex County, N. J., nor even to touch upon all the forms of the ores named, but to place upon record and call to the attention of the Institute some interesting facts concerning them. In May, 1875, after the Dover meeting, some of the members visited this locality, and, no doubt, it is fresh in their memories, being one of the best known mineralogical points in our country. It will be only necessary to describe it very briefly. Mine Hill and Stirling Hill, in Sussex County, N. J.,—the former being at the village of Franklin Furnace, and the latter near Ogdensburg,—are the only localities in the State where zinc ores are found in workable quantities.* Mine Hill is the more northerly, and mineralogically differs from its neighbor, chiefly in having no hydrated ores to speak of, while at Stirling this deposit is considerable. At both points Franklinite, red oxide, and silicate of zinc occur in large quantities. Mine Hill lies on the east side of the Wallkill River, above which it rises to an extreme elevation of about 150 feet. On the summit the outcrop of the Franklinite vein appears, while the lowest worked points are perhaps 10 or 15 feet above the level of the stream. Cornmencing at the northern end, where the Hamburg Road crosses it, this outcrop runs along the northwestern brow of the hill a distance of about 2000 feet, in a general southwest direction, to a point where is a large, cavern-like opening, called the "Southwest Opening." " Double Rock," about the highest point on the hill, lies near the middle of this 2000 feet of outcrop, and over or near it passes a property line, to which allusion will hereafter be made. At the Southwest Opening the vein bends abruptly towards the east,—the angle between the two parts being perhaps 45°,—and this easterly branch continues some 700 feet. From the northern part of the Stirling Hill deposit to the southern part of the Mine Hill deposit is about two miles, and in this interval the vein carrying Franklinite

By Walter O. Snelling

Continuation of the discussion of the paper of WaltER o. SnelLIng, presented at the New York and San Francisco meetings, February and September, 1915, respectively, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704 and Trans., li, pp. 657 to 671. A. C. McLaUghlin, San Francisco, Ca1.—It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out in the last 25 years. If his end products are what they seem to be, he has made. a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750" F, and pressure of 750 lb. per square inch. William A. WillIams, San francisco, Ca1.—What metal did you use, Mr. McLaughlin? A. C. McLauGHILIN.—Ordinaly seamless tubing, extra strong. William A. Williams.—Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Bittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150" C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. Best, New York, N. Y.—What is the difference between the Rittman and the Snelling process or system? William A. Williams.—he fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By Elmer W. Pehrson

OPINION seems widely divergent as to where we stand with respect to future mineral supply. From some quarters we hear that the United States is about to become a "have-not" nation and about to experience the evil consequences such a situation would entail. Others claim that we are still a treasure house of stored-up mineral wealth, the surface of which barely has been scratched. The data to be presented here support the conclusion that neither of these viewpoints is correct and that we are far from exhaustion of those mineral resources that are basic to our industrial economy. However, exhaustion is well advanced in a number of important subsidiary minerals so that we can no longer drift along with the easy-going philosophy that the earth will provide. The time has come when we must recognize the true situation and do something about it.

Jan 1, 1945

By W. C. Hittinger, J. McGlassan, J. W. Peterson

THIS paper describes the result of an investigation of the production of thin alloyed layers on a thicker substrate of pure germanium as one step in the manufacture of transistors.' The technique of alloying materials with semiconductors is a means of introducing small amounts of impurity elements in the alloyed regions of the crystal lattice of the semiconductor, the presence of which make possible the junction type transistor.2 Impurity elements are added which will produce regions having differing electrical resistivities and means of carrying current. Impurities are of two types: those which produce an excess of electrons (negative or n-type), and those which produce a deficiency of electrons (positive or p-type) in comparison to the pure semiconductor. The boundary between two such regions is designated a p-n junction. Elements in Group V of the periodic table, having five valence electrons, give rise to an excess of electrons when present substitutionally in the semiconductor lattice (usually germanium or silicon from Group IV). Similarly, elements in Group III create a deficiency of electrons. Germanium and silicon which are substantially free of impurities of either p or n-type are designated intrinsic (i-type) semiconductors. The usual junction ----trarnsistor has

Jan 1, 1958

By C. W. Crispell

THE four nomograms presented in this article were designed to simplify and make more, rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic scale. ? For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Compression It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Figs. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: HP = S X 144/33,000 PVn/(n-1) [(P'/P) n-1/Sn -1] (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 6, 1917

COMMITTEE ON INCREASE OF. MEMBERSHIP. C. R. CORNING, Chairman. ADOLPHE E. BORIS, First Vice-Chairman. THOMAS T. READ, .Secretary, Woolworth Bldg., New York, N. Y. Vice-Chairmen. JOHN H. ALLEN, GEORGE M. COLVOCORESSES, RICHARD AL ATWATER, JR., ROBERT PEELS, GEORGE D. BARRON, CHARLES P. PERIN, A. CHESTER BEATTY, JOSEPH A. VAN MATER, J. PARKE CHANNING, ARTHUR L. WALKER. D. C. Bard, Howard Eckfeldt, Philip N, Moore, W. de L. Benedict, R. C. Gemmell, T. H. O'Brien, John C. Branner, F. Louis Grammer, James J. Ormsbee, Palmer Carter, Ernest A. Hersam, Edward W. Parker, Allen J. Clark, Edwin C. Holden, John B. Porter, F. Crabtree, William L. Honnold, R. M. Raymond, George G. Crawford, Reginald E. Hore, Robert H. Richards, O. C. Davidson, C. Colcock Jones, LeRoy Salsich, E. V. D' Invilliers, Eugene P. Kennedy, Frederick H. Sexton, James S. Douglas, Chester F. Lee, Henry L. Smyth, Walter Douglas, - Richard S. McCaffery, F. W. Traphagen, Howard N. Eavenson, James F. McClelland, Elton W. Walker. Milton H. McLean, Meetings of this committee were held at the Institute headquarters on April 18, and May 2 and 15. It was resolved that meetings shall be held monthly on the third Friday of each month.

Jan 6, 1913

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of' cutting such a

Jan 1, 1892

By John K. Hammes

INTRODUCTION This introductory paper presents a description and definition of what the finance function is and what it specifically means for the mining industry. In its simplest terms, finance is, "management of money matters". As an area within the discipline of business administration it draws heavily on the related fields of economics and accounting, and to a lesser extent on marketing and production. MINING FINANCE DEFINED In preparing to write about what finance means to the mining industry, I asked a number of mining people the question, "What does mining finance mean to you?" Most responded that mining finance was "How a company borrowed money for mine development", and perhaps half those questioned included "raising equity" in the definition. It is not surprising that the mining industry concept of finance is the providing of funds needed for the objectives of the business, for that was once a view shared by authorities in the field of business administration. Further, it is certainly the area where much of the emphasis has been placed in the past ten to fifteen years as the industry struggled with the development of more remote and more refractory or lower-grade orebodies while profitability and internal cash flow were below expectations. No wonder project finance became such a popular topic. Twenty years ago it is probable that the emphasis would have been on mine valuation, for that subject was the area of finance then most often examined in industry publications. Papers concerning the pros and cons of payback, internal rate of return, and discounted cash flow appeared regularly. Let's examine the following situations, each the result of a financial decision: - Funding the exploration program in a developing country was accomplished by buying the next six-months budget needs in local currency. One week later the currency devalued 30 percent. If the purchase had been delayed or the local currency borrowed short term, a substantial saving would have been made in funding the program. - A major mining company borrows heavily to finance both expansion of its primary mining business and its entry into several new industry segments. When markets for all of the commodities it produces turn down for a prolonged period, there is concern over the adequacy of cashflow to cover debt service in addition to other company needs. The company's financial officers, however, had arranged very large committed credit facilities from numerous financial institutions which assured the availability of funds for several years. This enabled the company to implement a strategy to conserve cash, sell assets and survive until conditions improved. Further, short term suppliers of credit also were comfortable with the assurance that longer term credit was there to support them. -A medium size mining company financed several mines independently with limited obligations on the part of the parent company. The company decided to refinance the operations under one agreement. More flexible terms, lower interest cost and a longer tenor financing were achieved in return for assuming the risk as a direct obligor. - The exploration and development group of a large mining company proposes to develop a new mine in a country in which the company does not presently operate. When the investment is rejected they are advised that one reason was that the reinvestment assumption inherent in the discounted

Jan 1, 1985

By Charles Will Wright

ALTHOUGH the United States has long led all other countries in both the production and consumption of mineral products, the trend seems definitely toward an increasing dependence upon foreign sources of supply. This is not to take the position that we are either a have or a have-not nation. For years we shall continue to secure a large proportion of our needed minerals: from our own mines, but we must face the fact that this century has seen "a more thorough and intense development of the mineral resources of the United States and a greater depletion of its irreplaceable mineral reserves than has occurred in most other countries. An audit of our mineral production given in the attached charts discloses the extent of our deficiencies. Because of these facts, low-cost foreign sources offer a promising field for the investment of a portion of our mining capital and an opportunity to obtain for the United States a greater supply of strategic metals and minerals. How. ever, to reach this end, the industrialist investing in the foreign field must have the full co-operation and strong backing of the Federal Government and the involved Federal agencies.

Jan 1, 1947

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By Reinhardt Thiessen

IN THE general study of coal, all evidence points in the one direction -that coals had their origin in a manner analogous to that of peat. The best method of studying coal, whether it concerns its chemistry, composition, or physical condition, is to study peat. The essentials in a study of peat are a knowledge of the chemistry of plants, knowledge of decay and of the transformation process of plant-substances into peat. A number of facts must be emphasized, namely, (1) peat is formed under wet conditions only; (2) plants grow in the place where peat is formed; (3) all the plant substances go into the bog; and (4) all the plant substances are subjected to a series of phases of decay which are (a) in the air completely above the water level but in relatively moist conditions; (b) above the water level, but covered by debris; and (c) completely submerged by both water and debris.

Jan 3, 1925

CONTENTS PAGE SOUTHWARD, GLENN B.-Coal Mining by the V System. Discussed by Glenn B. Southward, Howard N. Eavenson, Edward B. Raiguel, Thomas de Venny, J.. J. Rutledge, Graham Bright 1 ARMS, RAY W.-Dry Cleaning of Coal. Discussed by Ray W. Arms, S. A. Taylor, Howard N. Eavenson, W. R. Crane, F. F. Jorgenson, G. R. Delamater. 6 EAVENSON, HOWARD N.-Data About Labor Employed in Various Bituminous Coal Mines. Discussed by Howard N. Eavenson, George H. Ashley, E. A. Holbrook, S. A. Taylor, R. V. Norris 14 Coal Mining by the V System Discussion of the paper of GLENN B. SOUTHWARD presented at the New York Meeting, February, 1924, and issued as Paper No. 1300-C, with MINING AND METALLURGY, February, 1924. MEMBER.-How do you pay your men for loading? GLENN B. SOUTHWARD.-Everything is on time basis. MEMBER.-How many men do you have loading across one of the diagonal faces? GLENN B. SOUTHWARD.-From four to five, depending on the length of the face. Our loaders are so arranged that each will give about twenty-five tons per loader a day. MEMBER.-How much timber do you use? GLENN B. SOUTHWARD.-A little more than will be used in room-and-pillar work, but not a great deal more. We have not attempted to recover much of our timber. MEMBER.-IS the mine union or non-union? GLENN B. SOUTHWARD.-Non-union. HOWARD N. EAVENSON, Pittsburgh, Pa.-I went .through that mine some weeks ago, and think that the author has been very conservative in his statements about the amount of loadings, etc. EDWARD B. RAIGUEL, Huntington, W. Va. (written discussion).¬Page 7 shows 60 men employed in day and night shifts, inside the mine, producing 750 tons per day. Let us reduce these figures to a man-hour basis, for comparison with Mr. Eavenson's figures on West Virginia mines, as follows:

Jan 6, 1924

By Edward W. Parker

IF one is to place any credence at all in the reports published in the daily press, the subject of conservation has been a very lively topic of conversation during the past 60 days, and it does not appear that the temperature of the summer months has been in any way moderated by the discussion. It is a subject in which we are all vitally interested and to which, so far as our mineral resources are concerned, both the Institute and the Geological Survey have liberally contributed. The report of the National Conservation Commission, appointed by President Roosevelt, contains a series of papers on the conservation of mineral resources, all of which were prepared by members of the Geological Survey and were compiled largely from information previously collected by that Federal bureau in the performance of its regular duties. It is not the purpose of this paper to reiterate in extenso any of the material already published. The contributions of the Survey officials to the Commission's report have been published in a separate document as Bulletin No. 394. This docunient is for free distribution and may be obtained upon application to the Director of the Survey. In the preparation of this paper I desire merely to make a few suggestions regarding the possible necessity of some restraint upon or control of one branch of the mining industry with which I have been somewhat closely associated for the past 20 years-that of coal. Most of the members of the Institute are cognizant of the suits brought by the government against the anthracite-operators in Pennsylvania, or the combination of interests commonly known as the ? hard-coal trust." No defense of any illegal combination in restraint of trade is intended, but there are some facts which should not be lost sight of, and unfortu-\

Nov 1, 1909

By Charles R. Keyes

I. INTRODUCTION. FOR a period of several years, and in a large number of cases, the Metallurgical Laboratories of the New Mexico School of Mines were employed in umpire work. During this time many important local problems were solved. Against the results of careful chemical analyses of ores, assay-returns were often checked. In many cases the assay-methods of mine and custom-smelter were compared, and both often found faulty for the ore concerned. A wide range of ores was covered. Many of the chemical analyses and assays were made by Dr. F. C. Lincoln, Professor of Metallurgy, now of the Montana State School of Mines. A varied series of instructive assays was prepared by Prof. R. B. Brinsmade, now of the West Virginia State University. Single assays and given series of tests were undertaken by H. T. Goodjohn, now chief chemist to the Cia. Metalurgica de Torreon, Coahuila, Mexico; by H. J. Hubbard, now superintendent of the Butters Divisadero Mines, Jocoro,. San Salvador, C. A.; by E. D. Morton, now superintendent of the Arizona & Nevada Copper Mining Co., at Lunning, Nev. ; and by A. W. Edelen, now superintendent of the Angangueo Unit of the American Smelting & Refining Co., in Michoacan, Mexico. A critical comparison of assay-methods that were found to be followed in the case of certain gouge-ores mined in the Mimbres range in New Mexico, and about which there had been much controversy, was made by D. F. Riddell, then Acting Professor of Assaying, and now superintendent of the Providentia Mines Co. of Parral, in Chihuahua, Mexico. To him is due the credit of much that is contained in the following notes, which be has generously permitted -to be used in advance of the publication of the complete results.

Jul 1, 1911

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By R. W. Shoenberger, J. E. McNulty, B. R. Kuchta, William Spackman, A. A. Terchick, M. E. Hopkins, Norman Schapiro, R. J. Gray, A. F. Duzy, M. P. Corriveau

INTRODUCTION * The United States is fortunate in having abundant reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most metallurgical-grade coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by petrography, paleontology, palynology, † physical stratigraphy, and geophysical methods are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining ( 1 ) the economic justification for mining the coal, (2) the optimum design of the preparation plant, and (3) the most effective use of the coal. Recent progress has been made in relating mineral matter, especially pyrite, in coal to geologic conditions and paleogeographic trends. l * Editor&apos;s note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. † Palynology is the science concerned with plant microfossils, especially spores. pollen. and other fossils of microscopic size.

Jan 1, 1979

By Bradley Stoughton

[Secretary&apos;s Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such &apos;as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913

By W. A. STERLING

IN the opencut iron mines of the Mesabi Range in Minnesota, the trend in mining is in the development of mining equipment and mining methods which will move surface overburden and ore-bearing materials with less labor and at a cheaper cost. This is a must for most of the independent operators. Their reserves of direct-shipping ore are extremely small and their operations are being conducted in small, or intermediate pits, with a high stripping ratio in the outer fringes, or shore lines of older pits. and in ore bodies passing from direct shipping to the washing and the intermediate, or retreat ore state. The trend is toward deeper stripping, longer and steeper hauls, and the necessity of moving a total of from three to five or six tons of overburden and ore material for each ton of shipping-grade ore produced. This naturally calls for greater production, with larger shovels, or draglines. cheaper drilling and blasting costs through the drilling of larger-diameter blastholes, and cheaper haulage through the use of trucks of larger capacity and more extensive use of belt-conveyor systems. This trend is notable both in stripping and mining.

Jan 1, 1948