Search Documents

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Norbert Asamer

At various stages during the hot rolling process, the different rolled products – blooms, billets, bars, respectively sections, but also slabs or plates – need to be cut. While the cross sections of these products are being reduced during each rolling pass, the lengths are being increased accordingly. Thus, it becomes necessary to cut the products to shorter lengths suitable for the next steps of production by state-of-the-art designed dry abrasive cut-off machines.

Jul 30, 2018

By Martin Dirks

Nowadays the sinter cooler often becomes the bottleneck of the sinter production, with outdated equipment leading to low productivity and high operation and maintenance costs. Furthermore valuable energy is simply destroyed in the cooler, which is not compatible anymore with a cost efficient and environmentally friendly sinter production. Paul Wurth has developed and improved two types of coolers, the annular cooler and the shaft cooler which offer flexible solutions to the specific situation of each client. The classic design of the annular cooler was completely revised and is now composed of a rigid ringframe construction as opposed to the traditional design with individual sintering cars, avoiding the typical problems of centering. Additional features of the PW annular cooler are the low air leakage rate and the increased effective cooling surface due to the removal of dead areas. This leads, in addition to the lower weight, to lower operating costs and a smaller space requirement. The shaft cooler stands out with an even smaller space requirement and a lower sinter outlet temperature because of a very long residence time of the sinter inside the shaft. Its development into a pure counter flow cooler aims at maximizing its energy efficiency, as it is designed as a system with a very low demand for cooling air, high air discharge temperatures and highly reduced dust emissions. For both cooler types flexible heat recovery solutions can be offered. These solutions include the supply of hot combustion air to the ignition hood burners and the sinter strand, the production of steam for the clients steam grid or the production of electric energy.

Aug 16, 2017

By D. A. Aranda-Regino, C. Gómez-de-la-Garza, J. Ramírez-Cuellar, L. A. Leduc-Lezama

The Pickling Line Tandem Cold Mill (PLTCM) at Ternium’s Pesqueria plant with a 5 stands, 6 high configuration started in 2013. At the time of the start up the work roll specification and grinding practices were stablished following a low risk policy to be able to sustain any start-up associated accident. Once a stable operation has been achieved both these policies are being modified to improve productivity and reduce costs. The specified hardness of the rolls has been increased and efforts are being made to optimize the grinding according to the rolling campaign length and materials. The fatigue damage in work rolls, after rolling and its removal by grinding was followed by hardness measurements made at the end of the rolling campaign and after grinding. Softening of the rolls after rolling was found mainly in final stands to be related to the averaged stress experienced during the campaign, the original roll hardness was recovered after grinding. Hardness evolution was also followed after each grinding step finding that the total amount of grinding could be reduced. The grinding practice was modified accordingly for the first stands and the yield of work rolls in them has improved.

Oct 1, 2019

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. In recent years, a rise in the chlorine content of this residue was observed, motivated by the increased use of scrap with impurities bearing this element. In this work, a qualitative assessment of the presence of chlorine in the electric steelmaking process is made. Complementing it, theoretical considerations based on the computational thermodynamics tool FactSage show the effects of the chlorine on the mineral species in EAFD and on gaseous species in the gas phase (HCl and Cl2). For this study, PVC polymer was used as the chlorine carrier substance which contaminates the EAF charge; presence of other minor elements in the system such as K, Na and Pb were also considered.

Aug 7, 2018

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By Raíza da Silva Juvenal, Suelen Silva Rocha, Artur Ângelo Alcântara de Assis, Jorge Luiz Valença Mariz

Um estudo de viabilidade econômica deve considerar parâmetros e incertezas inerentes a um projeto para produzir resultados econômicos consistentes, fornecendo ao investidor uma ferramenta de tomada de decisão. O presente estudo objetivou efetuar inicialmente a avaliação econômica convencional do cenário realista de uma mineração de agregados em fase de implantação localizada em Pernambuco, cujo Valor Presente Líquido (VPL) obtido foi R$ 24.006.309,20, o que representa um resultado positivo. Através da metodologia de Monte Carlo foi efetuada uma análise de risco considerando incertezas em 100.000 cenários, nos quais nove variáveis assumiram valores estocásticos dentro dos domínios definidos, produzindo assim uma distribuição estatística do VPL ao invés de um único número, sendo ainda efetuada uma análise de sensibilidade para identificar e quantificar as variáveis que mais impactam no resultado da avaliação. Por fim, os dois fatores mais influentes identificados na análise de sensibilidade inicial foram isolados e submetidos a uma nova análise de risco em outros 100.000 cenários. Foi concluído que o projeto é economicamente viável e que a probabilidade de gerar lucro aos investidores é de 99,77%, embora a probabilidade do VPL ser igual ou maior que o previsto pelo método convencional seja de 49,98%.

Oct 3, 2019

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Marcus Vinicius Laudares Mendonça

SMS calculates and improves tooth and flank profiles individually to realise a homogeneous pressure distribution over the complete load flank. With a tooth profile and flank profile according to AGMA, ISO or DIN standard the contact pressure varies along the load flank. To realize a homogeneous distribution of the contact pressure and to avoid a premature mesh, SMS improves the tooth profile and flank profile in three steps. First SMS is doing a preliminary calculation and design according ISO, DIN or AGMA standard, with safety factors based on more than 125 years of experience. Second SMS calculates and checks the local contact pressure at the load flank under consideration of shaft, gearing and housing deformation, as well as the bearing behaviour. Finally SMS calculates and designs an improved tooth profile and flank profile to receive a homogeneous contact pressure at the load flank. The result is an increase of the torque transmitting capacity of up to 30% of the SMS advanced gears with the same outer dimensions than traditional gears.

Aug 17, 2017

By Stefan Wahlund, Tom Adams, Mats Söder, Zhi Zhang

By applying high-end rolls with utmost performance and superior surface quality, hot strip mills can be further optimized. Operations in the mill have been also waiting for improved roll solutions that can minimize required roll changes which impact production efficiency. Limitations are usually due to the low performance and surface degradation of the rolls in the late finishing stands (F5 – F7). VICTURATM is the most recent developed grade for rolls utilized in the late finishing stand at Union Electric Åkers (UEÅ). These rolls have been tested and applied in mills all over the world. A significant improvement over the enhanced ICDP rolls has been observed. Hot strip mills are realizing improved operating efficiency and Total Cost of Ownership (TCO) through the transition of their entire roll inventories to these break-through products.

Oct 1, 2019

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018