Search Documents

By M. Newton

Optimization and sensitivity analysis of mineable economic volumes have been standard practise for open pits for many years now, and more recently software has become available to apply techniques for delineating mineable reserves for underground mines. In general these techniques have been applied to a single resource model to quantify mineable tonnes and grade for underground mining. However by using multiple conditionally simulated models both the risk associated with the mining parameters and the risk associated with variations in grade, tonnes and profit can be quantified. Using suitable software the mine planner can then easily and quickly define and compare alternative designs to assess and improve the robustness of and the confidence in the final design.

Jan 1, 2007

By Christopher Haycocks

Because of growing pressure from government and consumers to produce more coal, the mining industry must improve existing techniques and devise more efficient mining methods. Mining of the thicker, shallower and geologically superior coal seams in the western United States is being subjected to increasing pressure from environmentalists; and so in order to meet the demand, the coal industry is exhausting the more accessible surface seams and beginning to mine seam of over 1,000 feet in depth and less than. 30 inches in thickness. The longwall mining system is the natural choice for extracting deep and thin coal seams, as it operates almost independently of the overburden rock stress. Due to the added fact that longwall mining is an inherently more productive method than room and pillar mining, many coal producers are looking to it as a means of increasing productivity without a corresponding cost increase. The consistent rise in application of longwall mining in the United States in the last decade illustrates the excellent potential of this technique for the future. American mining conditions are geologically different from those in Europe where longwall mining has been highly developed and extremely successful. Although numerous successes have been recorded in the U.S. with this mining system, a substantial number of failures have also occurred. These failures are due primarily to roof control problems usually over the face, in the tail entry, or both. Another problem area for American operators contemplating the use of this method has been correct selection of equipment, which should be custom fitted to local mining conditions for optimum productivity. It is essential that correct estimates for chock resistances, support densities, supported and unsupported roof spans, as well as rates of advance and length of working faces be provided to optimize mining conditions. Unless extensive pilot projects are planned engineers must choose their equipment correctly at the outset. A typical investment in longwall equipment will amount to several millions of dollars.

Jan 1, 1979

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By R. L. Virta

Four companies ? H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. ? mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014

By Richard L. Stotlar

Introduction During the last decade, the metallic minerals segment of the industry could be categorized as a "feast-or-famine" business. It is no secret that metallic minerals are cyclical. Employment opportunities greatly depend on the supply and demand for its mineral products. It is also not unusual for there to be a lag between the industry's manpower requirements and academia's ability to produce new graduates. Due to this lag, there will be years with manpower shortages, as in the mid-1970s. At other times, supply will exceed demand. The question is where will the jobs be in the years to come? This presentation will review reasons why employment opportunities have declined within the metallic minerals industry. It will also predict future demand for mineral engineering graduates. And it will outline strategies for obtaining an employment offer. Historical Review - Employment From 1977 through 1983, about 75% of all metal mining employees were directly engaged in production activities, down from 83% in 1965. This decline reflects increased use of labor saving equipment, and more government regulation and foreign competition. Metal mining's employment decreased from 74,000 jobs in 1982 to fewer than 68,000 in 1983 - an 8% decline. The overall industry is having these problems because of the general downturn in the economy. For example, at the beginning of this decade, US automobile and steel industries were in trouble. Interest rates were too high and volatile. This adversely affected construction, housing starts, and manufacturing. All these industries, being large users of base metals, drastically affected the metals industry. US copper companies are still having problems. Reports indicate that many copper employers have cut production, laid-off workers, and permanently closed mines, refineries, and smelters. A decline in the demand for US produced metal products, such as copper, obviously affects some mineral engineering employment opportunities. Other factors to consider when looking at employment opportunities and why it has become difficult for US metal producers to compete in the world market include: • The grades of ore bodies of many US minerals are considerably lower than the grades of ores being mined elsewhere in the world. • The grades of ore bodies currently being mined in the US are steadily declining. • Foreign producers are largely government controlled and are not necessarily subject to the realities of supply and demand. • US environmental regulations have considerably added to production costs. Foreign producers in most countries do not have to worry about these additional costs. • US mines are getting deeper. This adds to the cost of production because of the increasing distance the ore has to be transported. • Plants and equipment are outdated. Many companies find themselves operating with equipment and plants that need modernizing or replacing. This obviously hinders competitive productivity. • Labor and management have had problems. Work stoppages in certain mining businesses and high wage and benefit costs in relation to foreign producers place US producers at a disadvantage. • Much land is unavailable. The US government owns most of the land considered to have the best potential for minerals development. Most of this land is unavailable for mining or exploration. Therefore, it appears that finding employment with a company whose primary business is mining and processing most metals, such as copper, in the US will be quite restricted and competitive. Future Demand It is difficult to anticipate what key employment opportunities within the next few years will be available to mineral engineering graduates. The Engineering Manpower Commission estimated that US engineering schools awarded 72,471 undergraduate degrees in 1983 vs. 66,990 in 1982. This was the eighth consecutive year in which the number of baccalaureates awarded has increased. On a brighter note, the US government's Occupational Outlook Quarterly stated that the growth rate through 1995 for all engineers is an encouraging 49% over present levels. The estimated number of engineers employed in 1982 is 1.2 million. The numerical in-

Jan 2, 1985

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009

By R. Fedors, T. Ghezzehei, D. Or

The phenomena of dripping into cavities (e.g. tunnels and drifts) within an unsaturated fractured porous medium under ventilated conditions is studied to improve estimates of dripping rates, drop sizes, and chemical composition of droplets that could affect the integrity of high-level nuclear waste packages placed in drifts. The sensitivity of dripping rates and water chemistry to ventilation is analyzed at various flow rates using analytical expressions linking flow on fracture surfaces to drop formation and evaporation. The model was tested using laboratory experiments involving machined aluminum slabs designed to represent a simplified morphology of a fracture face intersecting a cavity and using natural fracture surfaces from a welded tuff. Comparison with ten years of data on dripping in natural caves showed good agreement with model predictions. In particular, for low dripping rates, evaporation due to ventilation leads to larger drop sizes and alters drop chemistry by increasing the concentration of solutes in the drop relative to that in the water flowing on the fracture face.

Jan 1, 2000

By Jerry D. Pfarr, Gary Loving, David G. McDowall

Introduction The Open Cut is one of the best known landmarks in South Dakota's Black Hills. It is the site of the original discovery of the Homestake ledge, or lead, in 1876. Between that time and 1945, the Open Cut produced about 36 Mt (40 million st) of gold ore, the majority of which was drawn from underground operations. In 1981, a drilling program was undertaken to determine how much ore the old timers left behind. The results of this study indicated an ore body made up of broken and caved ground, and solid blocks in pillars and crowns. Reserves are estimated at about 6.8 Mt (7.5 million st) of gold ore, grading at 4 g/t (0.116 oz per st). Total tonnage of material, including waste, is estimated at more than 60 Mt (66 million st). The mining plan is a combination open pit and underground operations. The bottom 78 m (255 ft) will be mined by the underground panel-caving method. The open pit was designed as a contractor operation up to the expected milling stage or the point of sustained ore production. The pit was designed to avoid disturbance of US Highway 85 near Lead, SD. In 1983, the South Dakota Board of Minerals and Environment approved the mining and reclamation plan. Test mining began in the north of the Open Cut using open pit methods. Upon completion of the test pit, Homestake Mining's board of directors approved an expanded mine plan. They committed an additional $27.1 million to prestrip the ore body that is expected to yield 23 t (750,000 oz) of gold. Project life is estimated at 15 years. Exploration program In early 1980, 10 diamond drill holes were drilled from the surface in the vicinity of the east side of the Open Cut. The reserves delineated by that drilling were too small to justify their development. A continuation of this study attempted to quantify the tonnage remaining in the bottom of the Open Cut in the crushed remnants of old stope-and-crown pillars. This was originally thought to be minable by improved drawhole methods using highly mechanized procedures. By early 1981, however, thinking turned toward surface mining methods. The effort to quantify minable ore tonnage ultimately involved drilling 385 reverse-circulation rotary drill holes. These were drilled from August 1981 to March 1983 in several groups of holes. Each group, or drilling program, had a slightly different immediate goal or purpose. The holes were drilled to various depths using truck-mounted Drill Tech 40 drills with doublewalled 76 mm (3 in.) pipe with 134 mm (5.25 in.) three-cone rotary bits. Initially, wet drilling was employed using a cyclone collection system. Since cutting recovery was not as high as it should have been, all subsequent drilling was dry. The cuttings were collected and deposited by way of a cyclone into the sample bag. The pickup for the cuttings using the three-cone bits was about 50 mm (2 in.) above the bottom of the hole. Overall cutting recovery for the drilling program was estimated at 75%. Samples were taken on each 1.5 m (5 ft) of hole drilled. Each sample was split into three 48-g (1-2/3 assay ton) charges. The accepted value was the straight average of the three charges. Because of the known "nugget effect," assays were nearly impossible to duplicate. Therefore, to validate the regular assays, a series of screen fire assays were run. Based on this method of assays and checks, it was concluded that 10% more ounces would be produced than indicated by mine grade. Test pit The northernmost portion of the mine as planned is known as the Terraville test pit. This portion was mined ahead of the rest and separately. It provided answers to questions on slope stability, reserves correlation, mill recoveries, mining costs, and surface mining conditions in various weather and ground conditions since many boulders and much timber were expected. The mining plan for this portion of the pit was successful. More ore was mined than was expected. Mixing of Open Cut ore with underground ore in the mill feed was successful. Impact on the surrounding communities

Jan 10, 1987

By Richard R. Klimpel

Introduction Froth flotation is one of the most common unit engineering operations in use today. Its aim is to upgrade the quality of coal by removing ash/pyrite and separating selected minerals from undesired gangue materials. Flotation has been successfully practiced at the industrial scale for more than 50 years. Its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation has also shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a given equipment configuration. The operation must exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the mechanical flotation cell is scaleable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required - pH regulators, frothers, collectors, activators, and depressants - are all relatively inexpensive and common. They are not usually used in large quantities. Froth flotation is certainly one of the most versatile and forgiving unit operations in the chemical, mining, and agricultural industries. The problem with the industrial flotation process is that it is fairly easy to get reasonable results and relatively difficult to get excellent results. Why is it so difficult to fine tune the froth flotation process? There are some obvious reasons and a few not-so-obvious factors. The obvious category would certainly contain the tendency of natural feed materials (ores and raw coals) to have variable physical, metallurgical, and surface properties. This occurs even when special care is taken to minimize such differences with blending. There is another obvious reason for difficulty. An inherent broadness of the feed particle size range to flotation results from using any of the common industrial-scalefine grinding devices - ball-, rod-, or autogenous mills. Research has been done into the chemical reagent and equipment aspects of flotation. It has shown strong interactions (limitations) of chemical reagents and equipment on larger and smaller particles. The point is that current flotation practice works best on average- or medium-sized feed particles. The greater the amount of large or small particles, or of both large and small, the more difficult it is to achieve excellent flotation results. Other reasonably obvious factors include: • variations in mineral type and liberation sizes; • water chemistry variations such as those involving Ca", C03, or Fe", or various soluble metal cations; • the presence of stray organic materials such as returning soluble reagents or partially degraded reagents in reuse water; • the lack of reliable on-line instrumentation for monitoring and control; • frequent equipment malfunctions of all types; • excessive feed rates for installed plant capacity; • poor operator interaction with the process; and • poor reagent dosage control. There are less obvious, but real limitations to flotation. These are inherent in the design and operating characteristics of the most common cell design in use today - the mechanical flotation cell. Individual performance attributes of the chemical reagents used, along with their manner of use, also carry limitations. The bulk of this paper will deal with chemical reagents and their use. Chemical reagents In 1979, the author and his co-workers were asked to invent and implement, at the industrial scale, new flotation reagent chemistry. After reviewing some of the literature (Sutherland and Wark, 1955; Klassen and Mokrousov, 1959; M. Fuerstenau, 1962; D. Fuerstenau, 1976; and Leja, 1982), a series of carefully controlled plant scale tests were set up. These tests were designed to understand existing reagent scale-up from the laboratory to the plant. They were to quantify at the plant level the effect of some of the more important, controllable chemical reagent factors (frother and collector type, frother and collector dosage, pH effects). This is a learning experience that all researchers involved in flotation theory should experience. It quickly became apparent that: • because a factor is important

Jan 12, 1988

By Syd S. Peng

University research in the U.S. consists of three components; faculty, funding, and graduate students or postdoctorals. Individual faculty is the unit area of research that is not limited, although faculty normally performs research in their areas of expertise. Faculty can and often do join with other faculty in multidisciplinary research. Faculty research achievements or reputation reflects the standing of the program and university. Therefore, research is highly encouraged and regarded within the university community. Graduate students are the work force of faculty research and doctoral students are preferred for high-quality products. The federal government provides the majority of funding sources, with the remainder coming from industry, state government and others. Compared with other engineering majors, the mining engineering programs in the U.S. are unique in that they: ? Are small in terms of the number of programs, and number of faculty and students in each program. ? Serve a single industry (i.e., mining) and are thus cyclic, reflecting the up and down economic state of the mineral industries. Enrollment statistics during the past 70 years show that a cycle consists of approximately 30 years with the first 10 years up, followed by 20 years down. ? Have curriculum designed to emphasize and thus serve for either the coal, hardrock or industrial minerals industries. These unique features make mining engineering programs hard to manage in university environments. Funding for mining research has relied primarily on the federal government, i.e., the former U.S. Bureau of Mines (USBM) and currently the National Institute for Occupational Safety and Health (NIOSH). The mining industry does not directly perform, nor sponsor research projects. Federal funding provides primarily in-house research. In the last four decades, federal extramural funding was only available when Congress appropriated extra funding in response to mine disasters. For instance, a string of coal mine explosions in the mid to late 1960s prompted Congress to enact the Coal Mine Health and Safety Act of 1969. It provided massive research funding from 1970 to 1983 covering all mining-related subject areas. From 1984 to 1995, federal extramural research funding was minimal, through two generic mineral technology research centers for selected mining engineering programs. In 1995, Congress closed the USBM and transferred the health and safety of miners program to NIOSH. Federally-funded extra-mural research practically stopped from 1995 to 2006. In 2006 and 2007, in response to a series of disasters, including those at Sago, Aracoma, Darby and Crandall Canyon, Congress again appropriated funding for short-term re-search in selected subjected areas such as underground tracking and communication, mine seal and ventilation, and deep cover pillar extraction. Therefore, to develop a meaningful academic mining research program during the past three decades, funding needed to be drawn from other sources such as the mining industries. A ?meaningful? program requires a sufficient amount of consistent funding in order to produce effective results. A review of federally funded extramural research pro-grams shows that a great majority of contractors/grantees are private entities, involving few mining engineering faculty. This, in part, is due to the fact that mining engineering involves so many different subjects. Therefore, a small mining engineering program can only have resources to cover teaching in the core subject areas (i.e., extraction, ground control, ventilation and material handling), at best. In this respect, a successful and meaningful academic mining re-search effort requires strong supporting programs such as geology/geophysics, structural (applied) mechanics, material sciences, compute/software application, etc. Therefore, academic mining research had to rely on private sources such as coal companies, in the author?s case, for sustained funding in the past three decades. Relying on funding from coal companies presents several problems. The projects were small and considered routine consulting projects requiring practical answers in a very short time frame. This is not really suitable for academic research, for which the major goal of research is the training of graduate students. These short-term projects vary with time and mines, most of which are driven by U.S. Mine Safety and Health Administration (MSHA) or U.S. Office of Surface Mining (OSM) regulations. So sustained funding under such condition requires broad experience of coal mining operations, which is also not well-aligned for academic research where faculty tends to specialize in a narrow field. Consequently, under such a funding environment, it is important to keep in mind how to develop long-term academic research objectives from conducting small short-term consulting projects that require quick solutions. In other words, how to look beyond the quick answers and to develop broader and more fundamental theories applicable to other situations that advance the-state-of-the-art. In order to achieve this objective, faculty must act as the connecting link because graduate students come and go. Faculty must know the detail of each project such that they know what are the important unsolved problems, what to assign to specific graduate students and how to guide the next group of graduate students to continue the development and advance the mining science. Under such funding environments, the most effective way to conduct academic mining research and ensure quality products is to maintain a research group consisting of postdoctoral, PhD, and MS students of various rankings such that the senior ranks can assist in guiding the junior ranks, especially the senior PhD students who are experts in their dissertation research areas. A weekly meeting should be scheduled for the group in which problems encountered in the research are discussed or individuals take turns presenting the progress of their projects. During each meeting, the importance of open discussion on scientific issues must be emphasized. Thus, opinions are encouraged, debated, and rejected or accepted. Students are encouraged to listen to and analyze other points of view. In addition to training of this thought process, the meeting also helps identify the strengths and weakness of each individual. As the subject of research expands over time, the group?s and, thus, the faculty?s research experience broadens. With this approach, companies can get the quick answer they desire from expert research experience and the faculty can engage in meaningful applied and basic research that is most relevant to routine mine operations. The end result is that companies will have a high regard for academic mining research.

Jan 1, 2009

By Yoneji Kanoh, Masahiko Ohtsuka

In Japanese tunneling history, it has commonly been accepted that the long-round driving is difficult due to the complicated geological condition. Therefore, the maximum past record has been less than 3 m per round. A new record of advance was established in the 99 m2 headrace tunnel of Imaichi Water Power Station Project with an advance of 239.5 m in a month by drilling 3.9 m deep blast holes. The geology of the headrace tunnel composed of pyroxine andesite (ie. 960-1770 kg/cm2, VP3.1-4.3 km/s) which had several clay seams and open cracks and was moderately weathered. Automatic shotcrete machine was used for shotcreting. Rock support was specified according to the N.A.T.M. with each different rock type. The contractor achieved a remarkable tunneling advance not earlier experienced in Japan.

Jan 1, 1983

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006

By C. Laughton

Construction of a Deep Underground Science and Engineering Laboratory(DUSEL) is proposed under the auspices of the US National Science Foundation(NSF). DUSEL will provide scientists and engineers with a research facility capable of supporting a broad spectrum of fundamental and applied research deep in the earth’s crust. Research partners are physicists, biologists and geoscientists. DUSEL research calls for the construction of a network of shafts, tunnels and caverns that will provide laboratory facilities at depths of up to approximately 2 kilometers. The Project is still in the planning stages but, the initial experimental program is taking shape and conceptual designs have already been developed at two hard rock mine sites. This paper discusses the overall program and key engineering tasks being developed to support the construction of deep, large-span caverns. These caverns will house a new generation of physics experiments. As currently scoped, the experiments call for the excavation of permanent caverns with spans of up to 60 meters, sited at depths in excess of a kilometer.

Jan 1, 2007