Search Documents

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By J. Zwartendyk, A. Azis

"Every nation must decide how it should exploit its mineral resources so as to contribute most to its national objectives. It is argued that the present value of the future corporate income tax flow derived from mineral exploitation may serve as a useful indicator in moving toward a taxation policy that would contribute optimally toward the greatest public benefit.The future stream of corporate income taxes depends largely on the mineral endowment, consisting of deposits now being mined, known unmined deposits, and unknown deposits.Unknown deposits may be estimated by geological inference. Both known and unknown deposits can be categorized according to grade and size, and divided into economic and uneconomic deposits on the basis of certain prices, costs, rate of return and taxation levels.Computer simulations can be run of discounted cash flow models at various taxation levels to show the impact of taxation changes on future tax revenues."

Jan 1, 2014

By F. H. Touwen, N. C. Joughin

"Simulation is a technique for studying the operation of systems by synthetic experimentation. With digital computers it is possible to simulate even the complex production processes in gold mining. This has great potential in that it enables the investigation, analysis and comparison of mining systems to be done accurately, rapidly and at low cost. Two programs have been developed to simulate the principal underground production processes in gold mining.These are the simulation of any stope contract and the simulation of underground transport operations. The programs synthesize these mining activities from a large number of small unit operations. The stope contract program simulates rockbreaking by drilling and blasting and the cleaning of the panels by face and gully scraping. The transport program simulates the functions and movements of all vehicles running on rails on one underground level. The simulation programs provide an effective means for experimenting with mining activities."

Jan 1, 2014

By T. Flitton, R. Peattie

"The extreme depths and consequent expense of drilling and sampling the gold-bearing reefs of the Witwatersrand Basin have resulted in limited data being available for estimation of grade ahead of the mining face. There is, however, a wealth of information from mined-out areas of these deposits. This estimation challenge resulted in the development of a unique method of Mineral Resource estimation.AngloGold Ashanti (AGA) utilizes a technique termed macro cokriging (MCK), which allows for the integration of the limited advanced borehole data with the large chip sample data-sets from the previously mined-out areas by adopting a Bayesian geostatistical approach. The MCK process, in short, is the estimation of mixed support size data together with the application of four-parameter distribution models.The gold value estimation for the Carbon Leader Reef (CLR) on the AGA TauTona Mine is used in this paper as a case study of the process and to demonstrate the effectiveness of this technique through production reconciliation. The current method has been proven over the last 20 years and is now an established part of the Mineral Resource evaluation process within AGA.IntroductionOwing to the extreme depths of the goldbearing reefs at the AngloGold Ashanti (AGA) Witwatersrand operations and the prohibitive expense and time involved in drilling boreholes to the required depth, only limited drilling and sampling data is available ahead of the mining face. Whereas traditional estimation techniques are interpolative, within the Witwatersrand the estimation is primarily extrapolative, with the majority of the data being sourced from the mined-out areas. This significant challenge to estimation resulted in the development of a unique method of Mineral Resource estimation and evaluation."

Jan 1, 2016

By A. Sokolov, M. Demsky, E. Hasikova, V. Gostilo

"Previously, we upgraded and implemented two gamma activation assay (GAA) systems designed to analyse the gold content in raw ores at Zarafshan laboratory, Uzbekistan, and achieved a detection limit of less than 0.05 g/t under actual industrial conditions. Having started to design a fully modern, industrial GAA system for mining companies, this paper analyses the advantages, disadvantages, and special features of all major system components that can influence the sensitivity and accuracy of the analysis. The results of a study to optimize the detector geometry and sample size are presented and the performances of the linear electron accelerator, detector array, and sample transportation system of a modern, industrial GAA system for analysing gold, silver, and rare earth elements are considered. IntroductionGamma activation analysis (GAA) has considerable potential as a future replacement for traditional fire assay analysis in gold mining (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017). The essence of GAA is to irradiate ore samples with high-energy gamma quanta generated by an electron linear accelerator (LINAC) and then to use a gamma spectrometer to detect the induced activity of the excited gold nuclei. The advantages of this method are discussed in detail elsewhere (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017), where it is shown that GAA is uniquely suited to analysing ore samples when mining for gold, other precious metals, and accompanying elements.These advantages were realized in three industrial GAA laboratories that were commissioned in Zarafshan, Uzbekistan in 1977, in Magadan, Russia in 1979, and in Batagay, Russia in 1986 (Bourmistenko, 1986; Nii Tekhnicheskoy Fiziki I Avtomatiki, n.d). In 1989, a fourth industrial GAA laboratory was commissioned at a gold mine in Tommot, Russia. However, the project was subsequently halted due to economic reasons (Moshkov and Tjamisov, 2017). Currently, only the laboratory of the Muruntau mine in Zarafshan, Uzbekistan is in operation. The gamma activation method for gold determination is widely applicable at this mine owing to its high productivity and low cost of analysis. An outstanding aspect is the performance of more than one million analyses per year."

May 1, 2019

By J. Petersen, S. W. Robertson

Heap leaching is used extensively for the processing of low-grade copper, gold, and uranium ores. The hydrodynamics is often the most important factor that limits the rate of metal recovery. Over the past decades the author has performed physical and hydraulic testing of a large number of ore samples considered for heap leaching. The data were reviewed to investigate the effect of physical properties such as particle size distribution (PSD) and bulk density on the hydrology. The unsaturated flow through the bed is traditionally modelled with soil science models such as Brooks-Corey (BC) and Van Genuchten-Mualem (VGM), which relate the hydraulic conductivity to the degree of saturation, also known as the hydraulic conductivity function (HCF). However, most authors found a disconnect between the saturated hydraulic conductivity (KS) and the rest of the HCF, which is explained as resulting from a transition from capillary-to gravity-controlled flow. However, the author found no such transition, and found the flow to be governed by capillary flow throughout. Traditional BC or VGM fits were found to be appropriate, however it was necessary to modify the model to include a point of inflection, above which the hydraulic conductivity remains constant while the moisture content keeps on increasing. It was proposed that this is the result of unconnected or poorly connected pores, which fill with solution but do not create additional flow channels. The point of discontinuity was also found to correspond with the air entry point, measured independently from the air conductivity curves. On average, the air entry point corresponds to the experiential rule that the void saturation should remain below 65% for aerated heaps.

Dec 11, 2024

By S. Banisi, S. Zare, M. Mahmoudi, M. Maleki-Moghaddam, M. Yahyaei

As the orebodies become more complex and lower grade, there is an increasing demand from crushing circuits for a finer product. When the product from a crushing circuit does not satisfy the requirements of the downstream processes, the cost of production increases. Thus, enhancing the performance of cone crushers through optimisation of their operating factors becomes important. One of the key factors affecting performance of cone crushers is the filling of the crushing chamber during the operation. The effect of varying the filling of the crushing chamber of a cone crusher was investigated. To assess the crusher performance, parameters such as crusher capacity, power utilisation, and reduction ratio were used. Extensive plant trials were conducted to obtain samples and operational data when the crusher chamber was 50% full (half-full) and 100% full, which is 300 mm above the top of the crusher chamber (super-choked condition). The results indicated a 62% difference in the crushing capacity when the crusher was operated in a super-choked condition compared to the half-full chamber level. In the super-choked condition, the size-specific energy at 12.7 mm was 20 % lower than that of the half-full condition. The Bond ball mill work index (BBWI) of crusher product indicated that the BBWI of the product of the super choked condition is 5.6% less than that of the product of half-full condition. This can be attributed to the generation of micro cracks in particles due to increase in the interparticle breakage when the crusher was operated in the super-choked mode. Keywords: Cone crushers, crushing efficiency, crushing chamber filling

Jan 1, 2020

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

By Z. Levinson, R. Dimitrakopoulos

A mining complex is an engineering system where raw materials are extracted from several mines, processed, transported, and sold to the market. The uncertainty and local variability of material grades and their locations within the related mineral deposits are critical for determining the optimal life-of-mine extraction sequence, destination policy, operating modes, and capital investment decisions, which define the production schedule of a mining complex. Infill drilling is used to further characterise a mineral deposit and reveals information that changes the representation of the resource model and potentially the resulting optimal long-term production schedule. A self-learning reinforcement learning approach is proposed to determine the optimal drilling locations that maximise the net-present value of the long-term production schedule and the associated financial forecasts by adapting the schedule to additional information. A case study at a copper mining complex demonstrates a $70 M increase in project value by collecting drilling information with a $1 M budget.

Sep 1, 2021

By C. E. More

Some observations on &apos;ancient&apos; mining at Phalaborwa C. E. MORE. B.A. (Pretoria) (Visitor) A brief account is given of historical references to the Phalaborwa area, the first being to the mountain of copper and iron sought by Francois de Cuiper in 1725. These are followed by a description of several finds in the area, which are related to finds described in the literature and to Bantu tradition on the subject. Phalaborwa is one of the earliest known mining sites in the Republic of South Africa, Loolekop having been a mining centre, as shown by carbon-14 dating, since 770 A.D.

Jan 1, 1974

By L. Roux

This review was initially motivated by the author’s own experience in attempting to reconcile run-of mine production tons with the Coal Resource and Reserve estimation of mineable, in-situ tonnages. The primary scientific measurements and observations that are collected during exploration at the beginning of the value chain will have a profound effect on the future of the mining operation. Due diligence must be exercised during the planning of a new mine and during the life of an existing mine. The comments provided by the technical and economic assessment group of Venmyn Deloitte confirmed the need for this critical review. They found the reporting of Coal Resources in South Africa to be inconsistent. This was particularly problematic in the Waterberg Coalfield in Limpopo Province. In this coalfield there are two types of coal deposit present. The first is comprised of the thick intercalated, cyclic coal and shale/mudstone sequences of the Volksrust Formation. This overlies multiple coal seams within the Vryheid Formation, each of which is thick enough to be extracted as an individual raw coal unit. On the other hand, the interbedded coal and shale seams of the Volksrust Formation require beneficiation to separate the coal from the shale. The review examines practices and methods, investigates alternatives, provides checks and balances, and tests these against actual production reconciliations. In conclusion, the best estimates of the mineable, in-situ tonnage will be obtained from the air-dry raw material density. These estimates should be adjusted afterwards to allow for free moisture content. The adjustments are derived from reconciliation data. The greatest contributing factor to the over-estimation of Reserve tonnages is the moisture content of the raw material. This fluctuates significantly under varying conditions in situ, as well as upon exposure to the natural environment. The air-dried density of the raw material includes inherent (structurally bound) moisture within the matrix. It provides credible tonnage estimations of raw material available while also providing an indication of voids within the volume of material being assessed. The calculated solids percentage can be used to adjust the specific gravity, which is determined via the Archimedes principle. This will supply a representative estimate of the material to be mined.

Nov 1, 2021

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By C. Musingwini, A. S. Nhleko, M. J. Mahase

"In an environment like the mining industry, which is characterized by different stakeholders with multiple objectives, multi-criteria decision analysis (MCDA) is a useful approach for optimal decision-making. The application of MCDA techniques in the mining industry has predominantly been in mine planning and related problems, although no comprehensive survey has previously been undertaken to establish the application trends. A survey of the use of MCDA techniques was therefore conducted using case studies from the literature. It was noted that often two or more methods are applied to the same problem in order to increase confidence in the solution derived. As the number of criteria and alternatives increases, some methods become inefficient. A combination of the analytic hierarchy process (AHP) method with other MCDA techniques was the most frequently used approach, indicating the efficiency of the AHP method, especially when evaluating problems with more criteria and fewer alternatives. A combination of fuzzy theory with AHP or other methods incorporates uncertainty. The findings from the survey will benefit users applying MCDA techniques to solve mine planning and related problems.IntroductionA country’s natural resources serve the needs of different groups of people within the country. These different groups are collectively known as stakeholders (Herath and Prato, 2006). Stakeholders have different needs, preferences, and expectations, which describe and define the criteria to be considered in decision-making. The options available as solutions describe the alternatives in decisionmaking theory. The criteria and alternatives have to be evaluated simultaneously when making decisions, and this is when multicriteria decision analysis (MCDA) techniques become invaluable (Herath and Prato, 2006) because the human mind is considered to be limited when solving complex and intangible problems with several criteria and alternatives (Saaty, 2007). MCDA techniques belong to a broad group of techniques called multi-criteria decision-making (MCDM) techniques. The other group of techniques within MCDM comprises the multi-objective decision-making (MODM) techniques. MODM techniques are generally used to solve problems with an infinite number of alternatives, while MCDA techniques are generally used to solve problems with a finite number of alternatives (Musingwini, 2010)."

Jan 1, 2016

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By E. Van Der Lingen, A. Paton

"The South African ferrochrome industry has been faced with various challenges during the past few years, such as influences from the market, manpower strikes, China’s control over the demand for both ferrochrome and chrome ore from South Africa, and electricity supply constraints, placing increased pressure on the local industry to improve output in order to remain globally competitive. The year 2016 brought a dramatic change in the local ferrochrome industry, being marked by higher chrome ore prices and the takeover of some idle smelters.This study investigates the methods of technology acquisition used in various parts of the ferrochrome smelter value chain throughout a business cycle, and whether there is a preference for a specific acquisition in an explicit part of the value chain. The study also considers whether companies prefer to partner with local or global institutions for collaborative development, and the methods used by companies to protect their technologies.IntroductionSouth Africa holds the world’s largest chrome ore reserves and was the world’s largest producer of ferrochrome until 2012, when China became the leading ferrochromeproducing country. South Africa’s chrome ore (chromite) supply into the Chinese market has risen significantly from 36% of China’s total chrome ore imports in 2010 to more than 70% in 2016 (Fowkes, 2014; Creamer, 2017). China controls the demand for both ferrochrome and chrome ore from South Africa (Fowkes, 2014). China’s high import rate of chrome ore has resulted in ferrochrome prices being driven down and a depressed ferrochrome market. The South African industry meets the chrome ore demands but loses out on ferrochrome beneficiation.Furthermore, the local ferrochrome industry has been threatened with the overall poor competitiveness over the past few years, resulting in four of the eight producers ceasing operations at the beginning of 2016. Challenges experienced by the producers, some of which are directly linked to production costs, include influences from the market, productivity that was affected by wildcat strikes, China’s control over the demand for both ferrochrome and chrome ore, and electricity supply issues (Fowkes, 2014, 2013; Biermann, Cromarty, and Dawson, 2012). Ferrochrome production is energy-intensive and South African producers have faced higher electricity costs, electricity supply complications, and a weaker currency exchange rate since 2009."

Oct 1, 2018

By M. Splaine, W. Davison, D. C. Atkinson

"Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year L.P. A modified version of Rosenbrock&apos;s direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efffciency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are &apos;optimum&apos; in the sense that they yield the maximum present value of the operations.Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system."

Jan 1, 2014

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By B. k. Kenzhaliyev, M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

In research various desorbents were used to desorb the following rare-earth metals from Purosorb 140 cation exchanger, i.e. ammonium chloride; ammonium sulfate; a mixture of nitric acid and ammonium nitrate; a mixture of hydrochloric acid and ammonium chloride; a mixture of sulfuric acid and ammonium sulfate. It was established that a solution containing 30 g/dm3 of H2SO4 + 300 g/dm3 of (NH4) 2SO4 is the most optimal desorbing solution to desorb REMs from macroporous Purosorb 140 cation exchanger impregnated with rare-earth metals from industrial dihydrate wet-process phosphoric acid. It was established that the residual REM content in the cation exchanger decreased from 0.89 to 0.10 wt. % with an increase in the ammonium sulfate concentration from 10 to 400 g/dm3. Technological desorption regimes for rare-earth metals from cation exchanger were developed. The optimal conditions were determined to desorb rare-earth metals from the Purosorb 140 cation exchanger, particularly temperature 25°C; L:S ratio = (0.8 ÷ 1.1):1; duration = 1.0-1.5 hours. Keywords: Rare elements, sorption, cation exchangers, wet-process phosphoric acid, desorption

Jan 1, 2020

By S. Soren, K. Deo Mehta, G. Jha

The paper aims to find a sustainable sintering process through cleaner means, in order to achieve the desired outputs with zero environmental impact. At present, sintering has no control over its environmental impacts. These impacts occur when fossil fuels such as coal and coke are used in metallurgical sintering. These fossil fuels are undoubtedly effective in their assigned reducing task, but simultaneously emit about 220 kg of GHGs (greenhouse gases) per tonne of sinter produced. The current attempt has focused on reducing these emission levels by switching from coke to a renewable fuel source such as biomass. Biomass is a cleaner fuel source with a significantly lower emission footprint compared to coke. In the experimental campaign, sawdust and wood-charcoal were used in substitution for coke. Experiments were designed in a progressing substitution to obtain the maximum substitution ability without compromising the sinter properties. Sawdust as raw biomass source optimally substituted 10% of coke. The substitution levels were remarkably higher (30%) for wood charcoal due to its low moisture and high calorific values. A fuel blend with 30% biomass and remaining coke succeeded in producing a sinter with acceptable quality indices. Sinters prepared with or without biomass contribution shared an identical phase transformation and microstructures. In order to to maintain consistency in the process, every effort was made to maintain all operational and process parameters identically, except for the fuelling framework. Keywords: Sintering, sustainable, biomass, GHGs, fuel substitution

Jan 1, 2020