Search Documents

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Kung-Lee Wang

This report describes the linkage of all mining sectors with all other manufacturing, services, and final demand sectors of the U.S. economy. Besides being a basic data source, it provides a framework for aggregate economic impact analysis with respect to the mining industries. The framework is an open-static input-output model specifying 48 mining industries as classified in the Standard Industrial Classification Manual for all mining activities and 76 nonmining industries which collectively exhaust, all economic activities. The 124-sector model used in this report is an expansion of the preliminary 82-industry aggregation estimates made by the Department of Commerce. In the expanded model, 48 ruining industries are substituted for the original 6. The methodology used to ascertain the industry-by-industry procurement cost estimates and product ion flows necessary to the construction and expansion of the basic 82-sector model included personal interviews, case studies of specific mining activity analysis, and published and unpublished data from the Bureau of Mines and the Census of Mineral Industries, The end products of this study are two tables arranged to show the direct purchases necessary for each industry to support the level of economic activity and the total purchases generated in each industry throughout the economy by each $1 of aggregate economic demand in 1958. The tables may he used for economic impact studies and market analysis by firms engaged in or closely associated with the mining industries. Some illustrations of their usages are presented.

Jan 1, 1967

This report summarizes the results of a research project entitled "Fatal Accident Data Base Development." This project is the last project under Contract No. S0110601. Volumes I and 1I, "Industrial Engineering Study of Hazards Associated with Underground Coat Mine Production," summarize the original industrial engineering project and the Fatal Accident Report Analysis project. These projects were completed and accepted by the U.S. Bureau of Mines on December 10, 1971. Both volumes of the report have been made available by the Bureau to the public through the U. S. Department of Commerce technical information service. Another project under the same con tract, entitled "Equipment Operations Safety Study, ' was completed in January 1972 and the report was accepted by the U. S. B. M. at that time. The analysis in this Natal Accident. Data Lose Development report is closely related to analysis in both of the earlier reports. The original project involved an industrial engineering and safety of production operations for a representative sample of underground bituminous coal mines. The contactor was required to make recommendations 'in work practices, mining methods, equipment, and safety practices which can effectively reduce the fatality rate from rib and roof falls.' (Longwall mining methods were excluded from the study.) Time study and work element analyses were performed in over 50 mines as part of the field data gathering effort. Another requirement of the study was to develop sets of multiflow. Process charts, which are diagrammatic illustrations of the time-related interaction of mining, cycle job elements.

Jan 1, 1972

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States east of the Mississippi, and Information Circular 8705 covers States west of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two. Information Circulars.

Jan 1, 1976

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States west of the Mississippi, and Information Circular 8704 covers States east of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two Information Circulars.

Jan 1, 1976

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

The coal reserve base is defined for coalbeds having sufficient thickness for underground mining within a depth range compatible with economic recovery. The reserve data are compiled by the Federal Bureau of Mines by updating and reevaluating previous estimates of the U.S. Geological Survey, State geological surveys, and others. Through the application of computer techniques, the tonnages are compiled by State, county, coalbed, and rank. Coal reserve base is allotted to sulfur categories by a statistical apportionment of data from available Bureau of Mines reports and records. The coal reserve base in those States east of the Mississippi River, minable by underground methods, is estimated to be 169 billion tons in coalbeds greater than 28 inches in thickness to a maximum depth of 1,000 feet. Excluding those coals in reliability categories other than measured and indicated, the underground reserve base includes 162 billion tons of bituminous coal and 7 billion tons of anthracite. Of the total, 27 billion tons contains 1.0 percent or less sulfur. Most of this low-sulfur coal is in the southern Appalachian area. Approximately 16 percent of the underground reserve base is without available analyses. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves. The purpose of this system is to provide a common yardstick for determining coal resources and reserves.

Jan 1, 1974

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 61 surface coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, ?A Guide for the Evaluation of Human Exposure to Whole Body Vibration.? The comparison showed that about ha]f of all surface coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only on the order of 15% would be expected to experience vibration exceeding the exposure limit. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By L. B. Pankratz

Thermodynamic data on the sulfides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H°298 -(G° - H°298)/T, ?Hf°, ?Gf°, and log Kf are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1987

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969

By William H. Lewis

Energy Research Corp., under contract to the Bureau of Mines, has developed a new miners' caplamp battery. The new battery is based on nickel-cadmium technology and offers significant improvements in performance with reduced size and weight when compared to the conventional lead-acid battery presently in use. This report describes the design and fabrication of the nickel-cadmium battery, which utilizes a roll-bonded electrode structure. The final battery design has a 15-A-h capacity in a 2-112-lb package, which is over 2 lb lighter than the present lead-acid caplamp battery.

Jan 1, 1983

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1995

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962