Search Documents

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By R. E. Peterson

A reduction roasting/magnetic separation/flotation process for beneficiating oxidized taconite from the western Mesabi iron range in Minnesota was evaluated in a Bureau of Mines research program to insure an adequate supply of raw materials for future ironmaking and steelmaking needs. The research was performed on a sample containing 35.4 pct iron and representing a deposit of approximately 2 billion tons of raw materials. An average of 1,419 lb of oxidized taconite and 37 lb of lignite reluctant per hour were fed to a 35 -foot rotary kiln in which the iron oxides were converted to artificial magnetite. The kiln was heated with pulverized lignite and natural gas. Most of the dust collected from the kiln exhaust gas was pelletized and recycled to the kiln. Magnetic separation and cationic flotation of the roasted material in a 900-lb/hr pilot plant produced a concentrate analyzing 67.9 pct iron and 4.9 pct silica and containing 69.2 pct of the iron in the kiln feed.

Jan 1, 1981

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960

By William I. Nissen, Richard Havens

Continuous flotation studies were made at a 50 - lb - per - hr feed rate to confirm the effectiveness of a batch - scale procedure for concentrating phenacite and bertrandite minerals from Mount Wheeler ores that contained , in percent , 0.47 , 0.78 , and 4.7 BeO . The procedure for selective froth flotation of the beryllium minerals from a gangue composed chiefly of calcite , fluorite , and mica comprised closely controlled preconditioning with sodium fluoride and sodium hexametaphosphate in a series of small mechanically agitated tanks and use of a mixture of oleic acid with kerosine , fuel oil , or turpentine as a collector . It was difficult to adapt the laboratory flotation procedure to continuous operation . The principal problem of achieving adequate conditioning to depress calcite and fluorite ultimately was resolved by conditioning in series . Thereafter , three ore samples of different grades treated on a continuous basis yielded concentrates containing from 12 to 25 percent Beo from these relatively complex and difficult ores . Recoveries , on a BeO basis , ranged from 75 to 88 percent . Losses , which primarily were due to incomplete liberation , probably could be lowered in a commercial operation .

Jan 1, 1964

By R. V. Lundquist, A. E. Morris, E. L. Singleton

This experimental research was performed to determine rate - of - reaction constants on the MnO - C and Mn , C₂ - 3MnO systems at 1,100 ° , 1,150 ° , and 1,185 ° C. Reactions were conducted at atmospheric pressure under controlled flow of purified helium through the furnace chamber . The weight - loss method defined reduction percentages , and reaction products were identified by X- ray methods . The system Mn0 - C followed a linear reaction rate , and experimental results produced an apparent activation energy of 55.8 kcal per mole of Mn0 . The system Mn, C - 3Mn0 followed a parabolic rate of reaction law and yielded an apparent activation energy of 114.4 kcal per mole for the reaction .

Jan 1, 1964

By N. A. Eilertsen, Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for controlling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By H. B. Brunot, L. C. IlsLey

The chief object of the Electrical Section of the United States Bureau of Mines is the study of causes and means of preventing accidents resulting from the use of electricity in mines . A large part of this work for the last 20 years has been the inspection and testing of mining equipment under the provisions of schedules which give the minimum requirements considered essential for the safety of equipment intended for use at or near the working faces of dusty or gassy mines . During the first few years of this work , particular attention was paid to the explosionproof features of the various accessories such as motors , controllers , and other parts . The knowledge of the essentials necessary for safe designs of enclosures has since been augmented by field experience and by data obtained in testing a large number and variety of designs . With our present knowledge it would seem that a disproportionate stress was placed on making the various enclosures explosionproof , but not enough thought was given to the danger from wiring and connections outside of explosionproof enclosures . The list of equipment that has met minimum requirements for safety and has been approved as permissible by the Bureau of Mines includes storage - battery locomotives , power trucks , drills , loading machines , conveyors , cutting machines , room hoists , pumps , concrete mixers , and rock-dusting machines . The wiring on some of the machines is comparatively simple and sometimes , except for the trailing cable , may be entirely within the explosionproof enclosures . In general , there is outside wiring between enclosures , and on the larger machines the wiring may be extensive and complicated . In considering the safety of wiring for mining machinery , attention must be given the severe service and unfavorable surroundings imposed by mining conditions . Some of the matters that require consideration are : ground . The lack of care of the exterior wiring to be expected in the average mine . The lack of adequate periodic inspection of the wiring . The absence of adequate facilities for satisfactory inspection and repairs under- The severe conditions of moisture , dirt , mechanical injury , and low voltage encountered in mining service .

Apr 1, 1931

By Walter R. Storms, Allan B. Bowman

This paper , which describes mining methods and practices at the Mineral Hill copper mine , is one of a series being prepared by the Division of Minerals of the Bureau of Mines on mining methods , practices , and costs in various mining districts. of the United States . The Mineral Hill mine is situated on the northeastern piedmont of the Sierrita Mountains at an altitude of 3,650 feet in sec . 35 , T. 16 S. , R. 12 E. , and sec . 2 , T. 17 S. , R. 12 E. , Pima mining district , Pima County , Ariz . ( fig . 1 ) . The claims (figs . 2 and 3) are in a gently rolling area with only scant desert vegetation . The average annual precipitation is about 11 inches . The nearest surface water is the Santa Cruz River , an intermittent stream 8 miles east of the mine . The property is owned by the Banner Mining Co. , a Nevada corporation . This report presents a brief history of the mine , describes the geology of the area and the ore deposits , outlines methods of prospecting and exploration , and gives methods of sampling and the estimation of ore reserves and values . Development and stoping methods are explained , and methods of underground transportation , ventilation , mine drainage , and safety measures are described . The concluding section of the paper is a section on milling . The Mineral Hill mine is an old mine that was reopened in 1951 after having been closed for 30 years .

May 1, 1957

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By NIOSH NIOSH

This work explores application of a double alkaline leach method to extraction of alumina from Oregon ferruginous bauxitic materials. The process recovers a greater proportion of alumina from high-silica ores than is possible by a conventional single-leach method. This recovery is accomplished by calcining the ore, removing reactive silica in a preliminary dilute caustic soda leach, and then applying a second leach to dissolve alumina. Ores containing up to 15 percent Si~) 35 percent AI;:) Os, and 30 percent Os were examined. Under conditions of treatment established by experimentation, more than BO-percent alumina extraction was demonstrated. When and if conditions demand the use of low-grade materials, the double-leach process is capable of providing millions of tons of alumina from Oregon ferruginous bauxite.

Jan 1, 1963

By Christopher C. Jobes

Computer-assisted control of a mining machine can place the operator in a safe, remote location. A guidance system aids remote positioning of a mining machine by determining its position and heading. The mechanical position and heading system (MPHS) is one of several guidance systems being developed at the U.S. Bureau of Mines. The MPHS uses linear position transducers (LPT's) to provide navigation information during face maneuvers. This report presents an overview of the MPHS theory and implementation, including recent design modifications made for more successful underground testing. This report also presents the experimental setup and procedure for the underground test. The test showed that the MPHS provides reliable and accurate results and can, therefore, provide useful guidance information for face navigation.

Jan 1, 1992

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By P. M. Sullivan

This report describes a new application of electroamalgam metallurgy in recovering all the zinc as refined metal from galvanizers' sal skimmings. Pure zinc was recovered by electrolysis of skimmings leach liquors in amalgam cells. The following information was gained as a result of literature studies and subsequent laboratory investigations. 1. Reports in the literature indicate that pure zinc can be recovered from chloride solutions with the aid of amalgam cells. From Europe it was reported that amalgam cells could be used to recover pure zinc and chlorine from leach liquor obtained from pyrite cinders following a chloridizing roast.

Jan 1, 1956

By E. R. Bauer

This report presents the results of a cooperative study between BethEnergy Mines Inc., Ebensburg, PA, a central Pennsylvania coal mining company, and the U.S. Bureau of Mines to investigate longwall development entry roof instability. In-mine mapping of geologic and deformational features was conducted to reveal the major ground control problems encountered during gate road development. In addition, mining-induced pillar load monitoring was used to indicate development loading on variously dimensioned gate road pillars and to determine if pillar yielding occurred. Finally, visual observations of a variety of roof control methods were used to determine the most effective support elements for controlling cutter roof failure.

Jan 1, 1992

By J. Robert Wells

The Bureau of Mines has developed a spectrochemical procedure for determining 19 impurity elements in high-purity titanium metal, titanium oxides, and titanium halides in which all samples are converted to titanium dioxide. Determination of these impurities was studied in the general concentration range of 0 to 1,000 p.p.m., but different determination limits were found for the various elements. The procedure is quantitative for 18 elements but semi-quantitative3 for beryllium and has an overall relative standard deviation of 15.8 percent. Two mixtures were used, one composed of graphite and lithium carbonate plus gallium oxide and the other of graphite and lithium carbonate plus germanium dioxide. Each mixture was blended mechanically with an equal weight of titanium dioxide. Lithium carbonate served as buffer-diluent. Gallium was the internal standard for 1 impurity element, germanium for 7, and titanium for the remaining 11.

Jan 1, 1962

By Fieldner. A. C.

"In preparing this paper, an attempt was made to obtain results of plant-scale carbonization tests on washed and unwashed coal tram to same mine. A letter. in which the following questions were asked, was sent to some 50 coke-oven superintendents and others who might be interested:“What is the influence of washing coal on:(1) The chemical and physical properties of coke, as for example, the size, the amount of breeze, the fracture, strength, cell-structure, etc.(2) The quantity and quality of gas and by-products.(3) The capacity of the ovens.(4) The composition of the coal..""Your general opinion, as well as any specific data or results of testa, on this important subject will be greatly appreciated.""Of the 45 replies received, 24 stated that they had never used washed coal; 11 had used washed coal but had no comparative data on similar coals washed and unwashed; 7 answered some of the questions based on their general experience; and 3 gave some test data on Pittsburgh bed coal from western Pennsylvania. In none of the three tests did the washed coal come from the same mine as the unwashed. The washed coals in the three tests were from the same washery - one of modern construction in which the operations are under careful technical control in order to give a uniform product containing a minimum of surface moisture. The unwashed coals which were previously used in these plants were from different nearby mines in the same coal bed, and were supplied by the same company. Obviously, no sweeping or finale conclusions can be drawn from these few tests on coal from a single washery. Therefore, the writer vas obliged to consult the literature, coal-carbonization and coal-washing engineers, and other authorities to supplement the fragmentary information gleaned from the questionnaires in order to present a picture of chat gas engineers may expect from the use of washed coal in a carbonizing plant."

May 1, 1930

By John C. Edwards

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization-and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m-l for smoldering and flaming coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m-l, whereas the optical smoke detectors showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 2010

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010