Search Documents

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By Mark K. Larson

Researchers at the U.S. Bureau of Mines have developed a FORTRAN computer program that can calculate stress states from overcoring measurements obtained from hollow inclusion cells, triaxial cells, strain gauges installed on the wall of a bored raise, doorstopper gauges, borehole deformation gauges, or a combination of any of these gauges. Such stress states are calculated with reference to global and principal coordinate systems. The background of the development of the program, its capabilities, and its special features, as well as the input required, are described in this report. Sample output is also shown in appendix C. Difficulties associated with numerical calculations of principal stresses and directions are pointed out. Threshold values for detecting these problems are reported; these values may be changed by the user as desired. Several test problems were set up to verify the computer program and were successfully solved.

Jan 1, 1992

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By Ronald P. Hollenbeck

The value of mineral production in Alabama reached a new high of more than $246 million. 4 percent above the previous record established in 1964. New high values were reported for bentonite, portland cement, fire day, kaolin, miscellaneous clay, lime, crushed limestone, crushed marble, mica. salt, and sand and gravel. Among the States, Alabama ranked second in the production of bauxite and scrap mica and third in the production of native asphalt. The mineral industry of Alabama was dominated by the mining and processing of coal and Slone, the manufacturing of cement, and the production of crude petroleum, which together comprised 85 percent of the total value of mineral output, compared with 84 percent in 1964. The iron ore industry continued to decline. Coal production continued to increase, resulting in the State's coal-mining best year since 1948.

Jan 1, 1967

By William Y. Mo

This Information Circular provides a detailed background documentation of how the Bureau of Mines projects U.S. mineral demand to the year 2000. These statistical projections serve as a quantitative basis for contingency forecasting of the low, high, and probable U.S. demand for nonfuel minerals by end-use categories and are published in the Bureau of Mines Mineral Commodity Profiles and Mineral Farts and Problems series. Aluminum is used as an example in this study.

Jan 1, 1980

By R. W. Stahl

A survey of firefighting facilities and practices in coal mines conducted by the Bureau of Mines3/ showed such variations in equipment and apparent attitude toward fire protection that a comparison with other industry seemed advisable. Although other industry is confined generally to surface operations and the hazards probably are not as great, the same general methods of extinguishment are employed, so that the cost and protection at least should be comparable. An investigation of industry other than mines revealed a generally greater emphasis placed on fire-combating equipment, fire-brigade training, fire-fighting facility inspection, and fire-hazard elimination, as well as a greater average expenditure for fire protection.

Jan 1, 1959

By Sean Gallagher

This report was written in an effort to provide better control measures for low back pain (LBP) and low back disability in the mining industry. There are numerous factors associated with development of LBP, many of which can be effectively controlled while some cannot. Better job design is promoted as the best method of reducing cases of LBP and can also reduce the disability (i.e., lost time from work) associated with LBP when it happens. The report draws attention to what is currently known about LBP, what the causes are thought to be, and discusses recent back injury trends in the mining industry. Research describing unique physical demands in mining, such as the capabilities and limitations of working in awkward postures, is also presented. Methods that can be used to prevent initial LBP episodes are provided, including facilities design and layout for materials and supplies, use of mechanical-assist devices, improved design of lifting tasks, and better seat design. Methods of reducing the disability associated with LBP (including workplace design, proactive return-to-work efforts, communication, and management commitment) are also discussed. The report concludes that control of LBP and disability in mining requires a comprehensive approach to limit the repetitive loading that can occur on the low back due to manual materials-handling tasks and exposure to whole-body vibration (WBV). Specific recommendations include the following: ? Successful LBP prevention efforts require a proactive program that has strong management commitment and incorporates employee involvement. ? More efficient supply handling systems and use of mechanical-assist devices can greatly reduce exposure to hazardous lifting tasks. ? Lifting tasks should be designed to minimize low back stress. Tools to evaluate and redesign lifting tasks are presented. ? Improved seat design can reduce exposure to WBV and improve posture, leading to reduced LBP risk. ? The disability associated with LBP can be reduced. Getting the worker back on the job as quickly as possible is in the interest of everyone involved.

Sep 1, 2008

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By William S. Miska

The study is an economic evaluation of historical, current, and projected refractory uses in the iron and steel industry of the United States. The first part of the report presents a refractories classification and identifies principal trends in the refractories industry; such as, value and volume of shipments, prices of finished refractory products, the number of manufacturers and plants for refractories production and marketing. The main part of the report treats refractory use patterns and technologic developments affecting refractories usage in the iron and steel industry. Changes in use patterns in each furnace type, refractory, and installation costs and the future outlook for refractories in ironrnaking and steelmaking are covered. The last part of the report identifies the principal raw materials used in refractories production and treats trends in refractory raw material consumption. An appendix to the report contains historical time series graphs of shipments of refractory types used primarily by the iron and steel industry and principal refractory raw materials sold or used by producers. An equation of the line of best fit was calculated from the earliest to the latest year in each time series, usually 1950 to 1965; these were extrapolated in order to derive volume estimates for the year 1975.

Jan 1, 1968

By H. W. Gillett

This bulletin is issued by the Bureau of Mines as a contribution to the increase of safety and efficiency in the preparation and utilization of the mineral resources in the United States. Notable among the drains on these resources are the demands made by the nonferrousmetal industries, and in these the losses occasioned in melting brass and bronze are worthy of particular attention. This statement will be better appreciated by a consideration of the size of the brass industry. MAGNITUDE OF THE BRASS INDUSTRY. According to the Thirteenth Census, in 1909 there were in the United States 1,021 fu-ms that dealt mainly in brass and bronze. This total included jobbing foundries, manufacturing plants that both cast and machine a brass or bronze product, and rolling mills, but did not include iron foundries having nonferrous departments nor the numerous large brass-foundry departments of manufacturing plants that produce the castings used in the manufacture of electrical apparatus, cash registers, pumps, and the thousands of machines that require brass castings for their construction. Penton's Foundry List for 1910 gives about 1,150 exclusively nonferrous foundries and about 2,300 iron or steel foundries that also melt brass. If the rolling mills and. jobbing foundries in manufacturing plants be included, and if due credit be given to the rapid growth of the industry in the last few years, largely through the stimulation of the automobile busi¬ness, it is probable that not less than 3,600 plants are to-day melting brass or bronze.

Jan 1, 1916

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By William M. Knuth

The objectives of this study were the evaluation of the technical and economical feasibility of utilizing color and color infrared aerial photography to satisfy some informational needs for pre-mine planning, mine progress monitoring, and reclamation monitoring. Seven aerial data collection missions were conducted within a two year period over strip mine sites in Pennsylvania. Scales of 1:6,000; 1:12,000; 1:24,000; and 1:48,000 were flown on the first aerial mission. The 1:12,000 was chosen as the optimal scale for the remaining six flights. An extensive literature and legislative review and discussions with strip mine operators identified the informational parameters that could possibly be obtained from aerial photography. Interpretability accuracies were evaluated for parameters in the broad categories of land use, soils, water, vegetation, and geology. Seasonal interpretation characteristics were noted for infrared photography. Man hours for photointerpretation and costs of aerial data collection were monitored closely and incorporated into a cost benefit analysis. Those parameters that could be mapped, identified, or measured with accuracies =75 percent were incorporated into a photointerpretation training manual. An additional analysis was performed to determine the applicability of the interpretation methodologies and results developed for Eastern sites to Western surface coal mining sites. In addition, a separate aerial photographic interpretation manual was produced during this contract. It is intended to be utilized by eastern and midwestern surface mine operators and regulatory personnel.

Jan 1, 1978

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By Katherine A. Klein

Refuge chambers may potentially save the lives of miners during a mine emergency. For this reason, it is crucial that miners know how to operate them. Unfortunately, because refuge chambers provide so many services, they can be very complicated and difficult to operate. Therefore, NIOSH has created this document with suggestions for developing manuals and educational materials. A multidisciplinary team comprised of NIOSH engineers, sociologists, psychologists, health communication professionals, and geologists developed the recommendations contained in this document. These recommendations are based on an evaluation of manufacturers? instruction manuals from both the U.S. and globally, interviews with over 20 mining and safety experts, and an extensive literature review. This research, focused on the best practices for refuge chambers, led to the formulation of this document. It is intended to offer suggestions to manufacturers and mine operators on how to create effective and easy-to-understand training manuals for miners as well as tips to create the most comfortable and usable refuge chambers. It should be noted that these recommendations are not meant to substitute for manufacturer-supplied materials but rather to be used in conjunction with manufacturer?s materials. Manufacturers should always be consulted for up-to-date information about their chamber. Although different states and different mines refer to underground refuges by different names, this guide will simply refer to underground refuges nearest to the face as refuge chambers, whether inflatable from a skid or constructed from steel. Other popular terms for refuge chambers are rescue chambers, rescue shelters, and refuge shelters. Refuges that are nearer to the shaft, whether a prefabricated refuge chamber or one built into a crosscut, will be referred to as outby refuges because of their location in the mine. Outby refuges can be permanent, semipermanent, or portable and are usually located at every other SCSR cache. Outby refuges are sometimes called hardened rooms, outby shelters, and in-place shelters. When discussing outby refuges and refuge chambers collectively, this guide will refer to them as underground refuges. Other terms for underground refuges include refuge alternatives, locations of safety, and safe havens. This document is designed to be read either cover to cover or by specific section. It is recommended that on first read, this guide be read cover to cover. In subsequent readings, manufacturers and mine operators may find it easier to use the table of contents page to locate specific information on parts of the refuge chamber.

Jan 1, 2009

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By G. E. MeGlelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores. This technology has been adopted on a broad scale by the precious-metal-processing industry. This report presents information on the application of agglomeration technology to finely ground precious-metal-bearing tailings. Two commercial operations that have benefited from agglomeration technology are discussed. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1985

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used fur making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964