Search Documents

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By J. Paraszczak

ABSTRACT Diesel-powered loaders are a pillar of modern underground metal mining. As these mines are getting deeper and hotter and the emission regulations stricter, ventilation costs are soaring, affecting production cost. Also, the cost of diesel fuel is expected to rise. These may make the use of diesel engines more problematic. Electric load-haul-dump machines (LHDs) are an interesting alternative. This paper compares features and performance of diesel and electric, cable-powered LHDs. It overviews equipment offerings, and compares, analyzes and discusses technical parameters, operational problems and cost issues. The paper gives some conclusions about electric LHD applicability and performance, indicates possible applications, and suggests further research work.

Jan 1, 2013

By The Staff

"IntroductionThe published information concerning treatment of uranium ores has been very limited as far as Canadian ores are concerned. Such information has dealt mainly with refining processes for concentrates or rich ores, designed to recover radium rather than uranium; these methods could not be economically applied to low-grade ores.The purpose of this paper is to describe treatment possibilities for some of the .ores that have been treated at the Mines Branch, and .to show how the character of these ores influences methods and results.What is a Uranium Ore?Prospecting for uranium has been extremely active during the past two years and a great many occurrences of radioactive minerals have been recorded. Such prospecting has been based to a large extent on the use of the Geiger counter in the fie1d. This equipment is an invaluable aid when the results are properly interpreted.Most definitely, indications of high radioactivity do not always prove the presence of a valuable orebody. First we have to determine:(1) Is the radioactivity due to uranium or to thorium. There is no immediate market for thorium.(2) Can the uranium in the ore be economically recovered.Chemical analysis is the most exact method of determining uranium content, but a fair estimate of the uranium, and also of the thorium, content can be made from the difference in gamma and beta activity. The Mines Branch guards against misinterpretation by determining both beta and gamma activities and, if more than a minor amount of thorium is indicated, then a Chemical analysis is made."

Jan 1, 1950

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By A. E. Hilder

Introductory The following pages present the results of field investigations, laboratory and commercial tests, drilling, surveying, and preliminary development of the refractory clays which have been discovered recently in the township of Kipling, at the foot of Long rapids on the west side of the Mattagami river about 57 miles north of Kapuskasing and approximately 7 miles north of Smoky Falls, the terminus of the privately owned railway operated by the Spruce Falls Power and Paper Company, Kapuskasing (see Figure 1). Investigations on the clays of northern Ontario have been carried on over a period of seven years by officers of the Ontario Department of Mines, and I am indebted to the information published by that Department in reports by W. S. Dyer and A. R. Crozier, as well as?by Professor R. J. Montgomery, of the Ceramic Department, University of Toronto. It was, in large measure, the data given in the 37th, 38th, and 42nd Annual Reports of the Ontario Department of Mines that led me to make a personal investigation of the Mattagami River clays, with the result that we now have a commercial undertaking that will develop eventually into an industry of considerable importance in supplying the central manufacturing districts of Canada with refractories that heretofore have been largely imported from the United States. An extract from the 42nd Annual Report of the Department, Part III, 1933, page 75, reads as follows: "As for the refractory clay, the deposits are undoubtedly very large, but what is urgently needed is a deposit near the railway under sufficiently shallow overburden for recovery by stripping'. Having previously made an investigation of the clays adjacent to the Temiskaming and Northern Ontario railway, and these clays proving unsuitable, I turned my attention to the outcrops of refractory clays on the Mattagami river, first reported by Keele in 1919. This area offered possibilities within the economically permissible distance from rail transportation.

Jan 1, 1935

By D. P. Goodall

THE development of the oil and gas resources of Western Canada is not, as many suppose, a new industry. For more than half a century an intensive search for these valuable products of nature extended from near the western edge of the Precambrian Shield to the Pacific coast, and from the International boundary north to the Arctic circle. The chief centre of interest to the oil prospector has, however, always lain in that region lying east of the first range of the Rocky mountains and confined largely within the boundaries of the Province of Alberta. Although there are many geological problems yet to be worked out in this Province, the oil-well driller has helped in no small way in determining sub-surface conditions and distribution of rock formations. The chief geological conditions as they affect the drilling of wells are generally re-cognized, and for this purpose the Province may be partitioned into three main divisions: first, the disturbed belt or foothills region extending along the eastern edge of the Rocky mountains; second, the Alberta geosyncline, a broad trough lying to the east of and parallel to the disturbed belt and from which the formations rise eastward to level off and form, third, the plains ? ? region, extending over the rest of the Province. A relatively small area in the northeastern part of the Province is underlain with Precambrian rocks and may be excluded from this classification, as it is of no interest to the oil prospector. The foothills, or disturbed belt, has presented the greatest difficulty to drilling, though it has produced the largest yield of oil within the Province to date. Within the foothills belt, the rock formations consist largely of hard shales interspersed with layers of abrasive sandstones, which wear out drilling bits at an alarming rate. The strata, in most flaces, dip steeply and are cut by numerous thrust faults. Although some o the faults have great displacements, their presence may easily be overlooked or the extent of the fault misinterpreted. Many a prospect well has been located on what appeared to be a suitable geological structure only to find, after drilling through a normal succession of rocks for 4,000 feet or more, that the drill had passed through a major fault plane to a younger formation than that in which drilling was started. Only a repetition of formations already drilled could be expected at greater depths.

Jan 1, 1942

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By P. O. Parfitt

The Critical Path Method has proved its usefulness at Mcintyre Porcupine Mines Ltd. This paper illustrates the techniques of network construction and analysis, and the application of the method at the Mcintyre copper mine to various projects in the gold mine. C.P.M.'s use in a mill maintenance project is also discussed.

Jan 1, 1966

By A. J. Giroux

"The use of Ishikawa cause and effect diagrams in an analysis of requirements for improving safety and productivity at Falconbridge's Strathcona Mill is presented. The analysis lead to numerous small improvements being made with the cumulative effect being a significant improvement in both areas.INTRODUCTIONMill management in the 90's involves the major requirements to improve both safety and productivity in the workplace. These objectives, once seen as unrelated or even mutually exclusive, are now accepted as being complementary. Managers, trained either on the job (coming up through the ranks) or in an engineering discipline followed by first and second line supervisory experience are now turning to methods developed in consumer product manufacturing to ensure that all the components are in place to ensure the ore processing facilities are safe and efficient.This paper shows how management at Falconbridge' s Strathcona Mill used the Ishikawa ""fishbone"" diagram ( 1) , a method further developed by Deming(2), to put into place a comprehensive safety and productivity process. The Ishikawa/Deming concept is that no one element or program will itself continually improve a process or service. It is only by examining and then improving all the elements that are involved in the process or service that continuous improvement is obtained. The process was built on the Deming principle of worker ownership where management is the facilitator for putting into place the mechanisms whereby workers can themselves improve the operation. The process is illustrated mainly by examples of the changes made in the hope that these may be of direct help to other operations."

Jan 1, 1993

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By S. Kariyawasam, R. McNealy

Pipelines are subject to multiple threats often requiring quantification of pipeline risk and engineering evaluation of in-line inspection and other data to effect discovery of conditions defined by the regulation. Public concern and pressure from regulatory bodies are accelerating the need for pipeline operators to formalize and intensify their approach to integrity management. Most operators need a phased approach to progressively adopt the most relevant and needed assessments. The organized and relevant assessment steps need to be introduced according to data available and maturity of the integrity management program. Each refinement to the quantification offers distinct advantages to the user. In this paper, the progressive integrity assessment solutions using quantitative methods are presented. Methodologies for engineering evaluation of integrity in-line inspection data for immediate and future integrity are summarized. Corrosion is used as an example, but the approach is applicable to any time-dependent defect based hazard. Strategies for pipeline integrity management are discussed.

Jan 1, 2005

By D. C. Peck, James. R. S., Chubb. P. T.

"Abstract -The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered matie intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendritic­ pegmatitic matie pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and mag­ matie breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to lOOJo within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that af­ fected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd :Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Severa! factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic inter­ action with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion .The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Com­ plex, U.S.A.) in terrns of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economie concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginal­ type POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By André van Wageningen

Long-term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. Although a number of techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimisation techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the solution search space. The GA itself contains very little problem specific information and as such, has been linked to a discrete-event simulation (DES). The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimisation process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GA coupled DES is then used to ?optimise? a problem and the results are discussed.

May 1, 2004

By Leonard Kellogg

Introduction The Mine Manager or Superintendent is a man faced with a difficult problem. He must direct the activities of his mine in such a manner that, over a period of time, the greatest possible profit will be realized. In this respect, a mine is no different from any other business organized for profit. What makes the mine manager's task so difficult then? The profit of a mine is determined by -among other things -the grade of ore, the market price of the metal or metals produced, and the cost to operate the mine. The mine manager cannot do much about the first two of these, but he has considerable control over the operating cost. This cost will depend in large measure on the nature of the programme on which he plans to operate his mine. This operating plan may be broad or specific, on a long-range basis or on a month to month basis. The development of the plan, however, is made very difficult by the existence of so many factors which must be considered. These may be (1) factors requiring decisions based on the best judgment and interpretation of engineering and geological information available, or (2) items which must be considered but which are largely non-controllable. To be more specific, examples of such items would be: (1).-(a) The amount and type of development work to be done in relation to amount of ore to be mined. (b) Mining methods to be followed and type of equipment to be used. © Amount of exploration diamond drilling to be done if the orebody is not clearly defined. (2).-(a) Rock type and degree of hardness. (b) Width, depth, and pitch of veins. © Amount of work requiring timbering. (d) Faults encountered. (e) Water and gas conditions met with.

Jan 1, 1952

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016

By Unknown

With the present-day trend of rising labour costs and a lowering of production efficiency of workmen, it has become imperative that every effort be made to use manpower to the greatest advantage and to mechanize mining as much as possible. During the past few years this trend has gained much prominence in the Porcupine camp. In view of this, the executive of the Porcupine Branch considered that the Mechanical Movement of Muck would be a very timely subject for a Symposium. Accordingly a Committee was formed, with A. K. Douglass, Mine Superintendent for Delnite Mines, Ltd., as Chairman, and the Symposium was held in the Auditorium of the McIntyre Community Building, Schumacher, on March 25th last. Papers dealing with shovel loader and mechanical scraper operation at six of the larger mines of the camp were presented and discussed, and a tabulation was prepared giving data on the machines in operation at a total of eleven mines. The papers and tabulation, reproduced below, will doubtless be of considerable interest to operators of mines in all parts of Canada.

Jan 1, 1948

By Bob A. Hamaguchi

The Trojan Tailings Pond at Highland Valley Copper developed in only 15 years from a biologically inactive water body into a productive lake with a well established aquatic ecosystem. This process was assisted by a few simple and inexpensive procedures including fertilization and introduction of essential organisms. The success at the Trojan Pond has encouraged the use of similar techniques in other water bodies on the mine site. This paper details: ??The history, water quality and thermal behavior of Trojan Tailings Pond ?Techniques used in fertilization; introduction of micro-flora (algae etc.), large aquatic plants, zooplankton and invertebrates ??Selection and sources of suitable transplant materials ??Rate and extent of vegetation establishment ??Biomass production ??Rates of organic sediment accumulation over tailings ??Bacterial activity in the sediments ??Improved water quality through the bioaccumulation of aqueous metals in plants and the subsequent bacterial binding or precipitation of that metal during decomposition in the tailings sediment. Robert A. Hamaguchi graduated with a Mining Diploma from the British Columbia Institute of Technology in 1971, followed with a Bachelor of Applied Science in Mineral Engineering from the University of British Columbia in 1975. Since graduation, he has worked for numerous open pit mining operations throughout British Columbia. In 1991, he joined Highland Valley Copper working as an Environmental Engineer responsible for government liaison, reclamation, decommissioning and other environmental duties. Heather M. Larratt graduated from the University of Calgary in 1978 with a B.Sc. in Environmental Biology (First Class Honors). She has provided drinking water management and reservoir design for numerous cities and irrigation districts in British Columbia for 20 years. Heather has also worked for 12 years in reclamation of mine water, including passive SRB water treatment systems. Mark R. Freberg joined Highland Valley Copper in 1991 after working at number of mining operations in British Columbia and the Northwest Territories. He graduated in 1979 with a Bachelor of Applied Science degree in Mineral Engineering from the University of British Columbia.

May 1, 2001