Search Documents

By H. M. Woodrooffe

Three of the world's largest phosphate deposits are located in the USSR. These have an estimated reserve of 2,600 million short tons of elemental phosphorus. The best known lies in the Khibiny Massif, an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. The Khibiny Massif is north of the Arctic Circle in the Kola Peninsula at a latitude of 67° 30' north and a longitude of 35° 30' east. It is connected by rail to Murmansk, 100 miles northwest, and Leningrad, 900 rail miles south.

Jan 12, 1972

By S. LeFevre

THE solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covers briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results.

Jan 2, 1915

By Herbert D. Drechsler

Mining Finance is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm." The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance

Jan 1, 1985

By Herbert D. Drechsler

Mining Finance-is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm". The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance.

Jan 1, 1978

By Thomas T. Read

AT this time of the year, engineering schools are releasing a group of young men who probably are, on the average, in much the same attitude of mind as a person arriving at the terminal station of a railway journey; namely, of having a general idea of his objective, but having to make a decision as to just where he is going and how best to get there. The man leaving the train can at first follow the crowd, but it soon breaks up, as one goes one way and one another, until he has to choose his own course. The recent graduate may do the equivalent of following the crowd by accepting the first position offered, but this only postpones a decision as to where he is going and how best to get there. So many young engineers ask for advice as to what to do that the following statement has been prepared as an attempt to make a general answer to such queries. The engineer taking his first job should realize two fundamental relations. The first is that in electing to be an engineer he has elected to be a hired man. A consulting engineer has more freedom than a man on a regular pay roll, but he is also a hired man; hired for briefer periods at a relatively high rate, but under the necessity of simultaneously doing his consulting work and developing new retainers. There is nothing derogatory in being a hired man (all doctors, lawyers and clergymen are hired men), but the tardy realization that he is one seems to give many an engineer a mental jolt that can be avoided if he accepts it from the beginning.

Jan 1, 1926

By R. H. Lee

WITHOUT doubt, one of the most frequent and serious annoyances connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is ? tight," all available men are put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens-up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a.' cold," or at best a " high-sulphur," east is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot; the pressure rises; the amount of gas made' is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature " mentioned by Mr. .Johnson, and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke, high in sulphur, is used:

Jul 1, 1906

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By Charles L. Hosler

My function here today is not to illuminate any particular subject but simply to welcome you to Penn State and to the College of Earth and Mineral Sciences. Our college is, of course, dedicated to the same thing to which most of you have dedicated your lives--the exploration of the earth, the extraction of materials from it, and the production of useful things from those materials. We have about 2,000 students engaged in studying in preparation for service in these activities at the present time. Like other colleges of our type, we've undergone a great expansion just at a time when university budgets are contracting. This creates an interesting situation as to how we can best use our resources. This, of course, is the thing a lot of you are going to be talking about here--how we can best use the world's resources. As you well know, the expectations of the people of the world are rising, and, with the numbers of people increasing and with finite resources, there never was a time in history when it was more important that we become "quantitative" in our discovery, estimation, extraction, and utilization of those resources. I think it is admirable and very timely that you are gathered together to discuss your various approaches to this particu¬lar problem of quantifying and making most efficient use of the resources of the world. Yours is sort of a hidden profession, not just because you actually go underground, but because the public in general is not aware of where the materials they use come from. If you are successful in your professions the public will continue to be unaware. Only if you fail will your essential function become patently obvious. I wish you success both in your professional pursuits and in this particular meeting.

Jan 1, 1977

By Donald N. Rosenblatt

I would like to commend the author on his description of Pinto Valley's plant, and its interesting innovations. The author's discussion of 18 ft in diameter by 21 ft long primary ball mills (the largest wet ball mills made to date) is of considerable importance to those who have been engaged in the field of studying ball mill liner wear as it relates to various grinding installations. While it is stated that the mills have operated on a fixed tonnage and therefore it has been difficult to determine the best liner pattern, calculations from the data in the paper indicates that for mills 1, 2, 5, and 6, the tonnage per hour varies from a low of 223 for mill No. 1, up to a high of 314, for mill No. 2, while mills 5 and 6 calculate 285 and 246, respectively. Analysis of the wear patterns for the single wave liners used in mill No. 1 as compared to the double wave liners in mill No. 2, suggests that the author's data may tell more than he suspects about liner wear to be expected and thus what should be a best pattern selection from what may appear to be only limited hours of operation. [Fig. A] is a reproduction of author's [Fig. 10], to which wear forecast patterns [F-1 and F-2] have been added. Forecasts are based on many previous studies of large diameter ball mill operations over many years of field service. Calculations from the first-wear pattern provide an initial wear rate of only 13 lb of liner per 100 sq ft of shell liner surface per day, or 0.031 lb per to: ground. However, the second wear pattern is ac-

Jan 1, 1978

CONTENTS CATES, LOUIS S.-Factors Affecting Bank Slopes in Steam-shovel Operations. Discussed by Fred Hellman, Louis S. Cates, W. D. B. Motter, Jr., George S. Rice 1 CRANE, W. R.-Mine Subsidence in the Red Iron Ore Mines of the Birmingham District, Alabama. Discussed by George S. Rice, W. R. Crane, Louis S. Cates : 3 Factors Affecting Bank Slopes in Steam-shovel Operations Discussion of the paper of Louis S. CATES, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1360-M, with MINING AND METAL-LURGY, August, 1924. FRED HELLMAN, New York.-My experience with shovel mining has been restricted almost entirely to Chuquicamata as far as operation is concerned. We had there an unusual condition in that the rock is cohesive because of the salts in it, so that you can probably work higher banks than is possible in most places. Recently they have reduced the height of the banks and have found that lower bank affords better working condition than the higher bank. It took two years of experimentation to determine the best height of bank for that particular mine. Each mine should be considered by itself and, to state off hand the best height of bank. for any given mine is impossible. We worked the high banks in Chile without much trouble. We adopted high banks in the beginning in order to obtain the minimum expense in railway approaches at that time. The first plan was for 50 ft.; then to get production started with the smallest possible expenditure of money, the approach to the deposit was changed and the first bank had an ultimate height of about 180 ft. We worked that bank; quite success-fully, but I do not think that it could be done anywhere else.

Jan 7, 1925

By Isobel Clark

The increasing complexity of modern mining technology makes it ever more difficult to decide on the 'best* way to solve problems in mine planning. Yet with escalating costs it becomes increasingly more important for the mining engineer to be able to evaluate quantitatively the implications of the 'what happens if' postulation on the efficiency and economics of exploitation. The use of a model of the orebody can yield an estimate, not just of overall expected results, but also of the sensitivity of these results to possible variations in the orebody. Estimation techniques, such as Kriging, will produce the expected value for the grade of ore at any given point, or over any given volume within a deposit. However, the actual grades mined during production will - of necessity - differ from the predicted values. These possible variations, and the sensitivity of the management decisions to them, can be investigated in detail by the use of simulation. An orebody can be simulated which follows the known characteristics of the deposit at any given stage in development. These properties might be the histogram of grade values, the semivariogram from the samples, the actual borehole assays, geological constraints and/or interpretation, topography, lease boundaries etc. This would be one possible 'realisation' of the deposit as dictated by the currently known data. If several of these simulations are carried out, each conditioned to the current knowledge of the orebody, then it is possible to gain an idea of the range of possible outcomes of any mining procedure or decision taken - all of which are equally likely. Not only can the best decision then be taken, but its sensitivity to the inherent variation within the orebody, and to the ever present estimation errors may be thoroughly studied.

Jan 1, 1977

By R. H. Lee

Without doubt, one of the most frequent and serious ani~oyailces connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is " tight," all available men arc put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a "cold," or at best a " high-sulphnr," cast is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot: the pressure rises; the amount of gas made is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature" mentioned by Mr. Johnson,' and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke high in sulphur is used.

Jan 1, 1907

By F. W. Gordon

Since the waste gases of the blast-furnace came to be generally utilized in heating the blast and raising steam, the gradual improvement in the economy of fuel, mainly through the nse of higher temperature in the blast, has impoverished the gases. The increased output per unit of measurement of the furnace, and the increased height of the furnace, have markedly increased the resistance to the blast, thus enormously increasing the duty required from the gases. In other words, a gas reduced in heating power by a further dilution of CO, is required to raise the temperature of the blast to 1800' Fahr., where formerly 600' was a good temperature, and at the same time to raise steam enough to drive the air into the furnace at a pressure of from four to eight pounds in coke practice, and from eight to twelve pounds in anthracite practice, and also pump at least double the water formerly used at furnaces. Hence the necessity for the employment of the best scheme for thoroughly consuming these gases with the least dilution of air, and the use of the best device for absorbing the heat prodnced for the purposes above mentioned. In a former paper before this Society the writer called attention to such improvements as had been made by his firm, by which it was claimed 1400' Fahr. could be maintained in the blast by a less consumption of gas than was required to maintain 900' when using pipe-ovens; and it would not be too much to say that 1600' Fahr. might now be written in place of the 1-400. The object of this paper is to give the practice of our firm in the

Jan 1, 1884

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

By William R. Webster

In view of the good results which have followed the wide discussion of the rail-specifications of the American Section of the International Association for Testing Materials, I now offer for discussion its specifications for steel forgings and steel castings. It is not necessary to emphasize the importance of reaching definite conclusions on these subjects. Engineers, consumers and manufacturers are alike interested in securing good, reliable, uniform steel. In this connection, I would call particular attention to the important paper read by Mr. C. H. Ridsdale, last September, before the Iron and Steel Institute, as bearing on them; and, for convenience of reference in the discussion, I append the Table in Section VI. of his paper, on a Manifestations, Classified mider Heads of Faults of Different Types. appearing after Treatment by the User, for Tracing their Probable Source."* The discussion of these specifications will be practically a continuation of our former discussions on "The Physics of Steel." We have passed through a period in which the chemical composition of steel has received the greatest prominence; but failures of steel forgings and castings of the best chemical composition have shown that we could not control the quality of the finished product by the chemical composition alone. It must be admitted that differences in the physical properties of the steel, greater than those due to small variations in composition,are produced by heat-treatment, both in connection with the mechanical work of forging and otherwise. The present result is a strong tendency to deem the heat-treatment more important than the chemical composition. I think the mean course is the safer. We should give them equal importance; for we know that to produce the best results me must start with a good

Jan 1, 1903

By John Birkinbine

EXTENDED discussions, by inviting attention to problems affecting the conservation of natural resources, have encouraged investigations as to their sufficiency, with the general result that the more thorough the examination, the less cause appears for anxiety as to the exhaustion or serious depletion of these resources. The extent of industrial development, the large plants and the enormous volumes of materials required, when compared with conditions a few decades ago, are sufficiently startling to enlist the attention of those who "fear .the pace," and yet in but few instances has real solicitude for the future. been warranted by a knowledge of true conditions. In a former communication, presented 5 years ago,1 I endeavored to emphasize the fact that true conservation represented the best utilization of reserves and not the locking up of resources for future use; a conviction which has become more pronounced as the subject was investigated. Prophecies of the, early exhaustion of mineral resources have raised the question as to our permanent reliance upon these, and encouraged inquiries which have in most cases developed reassuring conditions. But the fact that the future appears less dark than prognosticated cannot excuse wastefulness or improvidence; and detailed study which demonstrates an apparent abundance of natural resources should encourage their best application. In making inventories of resources one is liable to confine conclusions as to availability upon present circumstances and conditions in the past, or to formulate data for the future upon methods which are rapidly being displaced. In reserves which are not reproductive, such as minerals, the possibilities of exhausting the supply are startling if estimates assume that future extensions will follow methods which were less economical than those now employed, or to he used, and we dare not claim that the limit of advanced practice has been attained.

Jan 9, 1914

By Homer Staley

THE casting alloy 88 copper, 10 tin, 2 zinc, commonly known in England as Admiralty metal and in this country as Government bronze, gun metal, or Naval Department composition G, has, at its best, many valuable properties. However, its physical properties are known to vary widely with slight changes in method of manufacture of the castings, such as slight variations in composition, variation in pouring temperature, kind of mold used, method of pouring and gating of molds, size and shape of castings, amount and kind of heat treatment., and so forth.1 The microstructure of castings made from this alloy is influenced by slight variations of composition, rate of cooling, and kind and length of heat treatment. This is best understood by reference to the equilibrium diagram. The part of the diagram in which we are interested and the effect of the thermal equilibrium relations on the physical properties of the alloy 88 copper, 10 tin, 2 zinc, have been discussed by Hoyt, Camp-bell, Primrose, and Rawdon.2 In Fig. 1 is given the equilibrium diagram of the copper-tin alloys. Briefly stated, the relations of composition and temperature changes are as follows. Compositions between A and a consist of but one constituent-the a bronze, which is a, solid solution of copper and tin, rich in copper. On cooling from the molten state these compositions gradually crystallize, at temperatures above 790°, into a mass of interwoven tree-like crystals or dendrites. The cores of the dendrites are rich in copper and the percentage of tin gradually increases as the surfaces are approached. As cooling progresses, after all the metal has crystallized, no further changes occur, in the crystals other than diffusion within the crys-

Jan 9, 1919

By Magnus Troilius

SINCE the discussion on steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results obtained by different chemists. To any one having the least acquaintance with chemistry, it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application of chemistry to steelrail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it occurred to me, two years ago, that I could not do better than start a laboratory of my own, and engage one of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus obtain without delay thoroughly accurate determinations. Moreover, in order to carry on the operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as mas found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882