Search Documents

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900's, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

Development of Technology for Complex Uranium Ores Processing on the Flotation Process Basis

Sep 13, 2010

By Ü. Atalay, G. Alaeddinoglu, G. Özcengiz, G. Özbayoglu, Z. Özdemir

In this study, bacterial pre-treatment was applied before cyanidation in order to enhance the solubilization of silver from Artvin-Kafkasör ore Direct cyanidation process was found inefficient to recover silver from the ore. Only 40.36% silver recovery was obtained with direct cyanidation while silver recoveries of above 60% were obtained after bacterial treatment. Thiobacillus ferrooxidans was used as the microorganism in pretreatment tests. Effects of various parameters such as pulp density, duration, inoculum size and particle size on silver recovery have been investigated in this study.

Jan 1, 2001

The mineralisation consists principally of layered pyrite, phalerite and galena, situated conformably within a sequence of tuffaceous, bituminous shales and dolomitic sediments that include slump breccias. The sediments show little evidence of post sedimentary reconstitution. A volcanic-exhalative-sedimentary origin is postulated for the mineralisation. Attention is drawn to the similarity between the McArthur deposit and the lead-zinc-silver orebodies at Mount Isa. The primitive nature of the sulphides is reflected by their adverse metallurgical behaviour, and it seems that the best prospect for milling and flotation benefication may lie in the production of separate zinc and bulk concentrates

Jan 1, 1968

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By J. Sammut, T. G. Joseph, R. Andreev, M. Curley

"Decisions regarding mining method and subsequent choice of excavator must take into account the quantitative factors of productivity, availability, and capital, operating, and maintenance costs. Dig performance was compared between a hydraulic excavator (HE) and electric rope shovel (RS) of similar size class (i.e., use the same amount of energy to excavate a unit quantity of the same material from a mining face), focusing on the quantitative factors above. Machine performance, normalized to bucket capacity, was assessed as a function of hours of service (60,000 hours per machine). Results showed higher production rates for the HE of similar capacity and age. In general, the RS exhibited lower service cost per volume capacity, though it had higher capital cost. The RS became more cost effective than the HE of similar capacity within approximately 30,000 hours of service. ¦ KEYWORDS Cost, Electric rope shovel (RS), Excavation, Hydraulic excavator (HE), Surface mining RÉSUMÉ Les décisions concernant la méthode minière à adopter et le choix ultérieur d’un engin d’ex¬cavation doivent tenir compte des facteurs quantitatifs de la productivité, de la disponibilité ainsi que des coûts d’investissement, d’exploitation et d’entretien. Cette étude compare les performances en termes d’excavation d’une excavatrice hydraulique et d’une pelle électrique à câbles de même taille (qui utili¬sent par exemple la même quantité d’énergie pour creuser une quantité unitaire du même matériau dans un front de taille), en se concentrant sur les facteurs quantitatifs susmentionnés. La performance de la machine, normalisée à la contenance du godet de volume unitaire, est évaluée en fonction des heures de service (60 000 heures d’activité par machine). Les résultats montrent des taux de production plus élevés pour l’excavatrice hydraulique d’une capacité et d’une ancienneté similaires. De manière générale, la pelle électrique à câbles affiche un coût d’entretien par capacité volumique inférieur, mais son coût d’in¬vestissement est plus élevé. La pelle électrique à câbles devient plus rentable que l’excavatrice hydrau¬lique d’une même capacité au bout d’environ 30 000 heures de fonctionnement. ¦ MOTS CLÉS coût, excavation, excavatrice hydraulique, exploitation à ciel ouvert, pelle électrique à cablesINTRODUCTION The most common excavating tools in surface mining operations are the hydraulic excavator (HE) and electric rope shovel (RS). In general, electric RSs are more reliable and cheaper to maintain (P&H Mining Equipment, 2007), but where complicated geological conditions exist, HEs are preferred because they are generally considered to be more mobile."

Jan 1, 2019

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By L. Watters, R. Terry, D. Placha

Dense medium cyclones are the preferred means for cleaning 1/2 in. x 14Mesh to 28Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2mm) down to 14 Mesh to 28Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Feb 24, 1997

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

By Warren L. J, Horsley R. R, Meagher L

Mineral concentrators often use process water that is very saline and/or hard. In this paper the effect of increasing concentrations of sodium chloride and calcium chloride on the rheological properties of 70 wt% quartz suspensions (d5o - 10.6 ¦m) is reported. The apparent viscosity at 100 s t in 5 mol dm -3 sodium chloride solutions (approx. 300,000 ppm) was nearly 500 times the viscosity of water without salt or particles present. Part of the increase in viscosity is caused by aggregation (coagulation) of the suspension.

Jan 1, 1989

Jan 1, 2007

Removal of Arsenic in Enargite from Copper Ores by Flotation and Leaching in NaHS Media

Sep 13, 2010

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005

By Larry G. Stolarczyk

Jan 1, 1980

The paper presents the development of an integrated computer aided design and planning of open cast mining, with the use of object-oriented modelling and geoinformation technologies, on the example of interaction of the subsystems on planning optimisation and freight traffics.

Dec 6, 2010